CONNOR-WINFIELD FPHA554

THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
HTTP://WWW.CONWIN.COM
PRODUCT
D ATA
SHEET
CRYSTAL CONTROLLED OSCILLATORS
CW 0503
FPHA554
155.52M
SURFACE MOUNT 5.0V PECL CLOCK
ABSOLUTE MAXIMUM RATINGS
FPHA554
TABLE 1.0
PARAMETER
UNITS
MINIMUM
NOMINAL
MAXIMUM
UNITS
-40
-
85
°C
-0.5
-
7.0
Vdc
Storage Temperature
Supply Voltage
(Vcc)
OPERATING SPECIFICATIONS
NOTE
DESCRIPTION
The Connor-Winfield
FPHA554 is a fixed frequency
surface mount Crystal
Controlled Oscillator (XO)
designed for applications
requiring low jitter and tight
frequency stability. Operating
at 5.0V supply voltage, the
FPHA554 provides PECL
Differential Outputs with an
enable/disable function.
TABLE 2.0
PARAME TER
MINIMUM
NOMINAL
MAXIMUM
UNITS
NOTE
44.736
-15
0
-
MHz
ppm
°C
1
-
200
15
70
(Vcc)
4.75
5.0
5.25
Vdc
(Icc)
-
-
70
mA
Jitter (BW=10Hz to 20MHz)
-
-
5
pS RMS
Jitter (BW=12kHz to 20MHz)
-
-
1
pS RMS
SSB Phase Noise at 10Hz offset
-
-60
-
dBc/Hz
SSB Phase Noise at 100Hz offset
-
-90
-
dBc/Hz
SSB Phase Noise at 1KHz offset
-
-100
-
dBc/Hz
SSB Phase Noise at 10KHz offset
-
-125
-
dBc/Hz
SSB Phase Noise at 10KHz offset
-
-135
-
dBc/Hz
MINIMUM
NOMINAL
MAXIMUM
UNITS
NOTE
-
-
Vdc
2
3.40
Vdc
2
Center Frequency
Total Frequency Tolerance
Operating Temperature Range
(Fo)
Supply Voltage
Supply Current
INPUT CHARACTERISTICS
TABLE 3.0
PARAMETER
Disable Input Voltage (High)
(Vih)
3.96
Enable Input Voltage (Low)
(Vil)
-
PECL OUTPUT CHARACTERISTICS
PARAMETER
LOAD
Voltage
(High)
(Low)
Duty Cycle
Rise / Fall Time 20% to 80%
Package
5.0V OPERATION
TABLE 4.0
(Voh)
(Vol)
PACKAGE CHARACTERISTICS
FEATURES
MINIMUM
3.96
45
-
NOMINAL
50
-
MAXIMUM
50
3.40
55
1
UNITS
Ohms
Vdc
Vdc
%
nS
LOW JITTER <1ps RMS
NOTE
3
OVERALL FREQUENCY TOLERANCE:
±15ppm
TEMPERATURE RANGE: 0 to 70°C
4
PECL DIFFERENTIAL OUTPUTS
ENABLE / DISABLE
TABLE 5.0
Non-hermetic package consisting of an FR4 subs trate with grounded metal
cover.
SURFACE MOUNT PACKAGE
TAPE AND REEL PACKAGING
PROCESS RECOMMENDATIONS
Solder Reflow
Wash
TABLE 6.0
The component solder used internal to this device has a melting point of
221°C. The peak temperature inside the device should be less than or
equal to 220°C for a maximum of 10 seconds
Ultrasonic cleaning is not recommended.
Notes
1) Includes initial tolerance, deviation over t emperature, supply and load variations, shock, vibrati on and 10 years aging.
2) When the oscillator is disabled, the true output is in a low state (Vol) and the complementary output is in the high s tate (VoH).
3) Output must be terminated into 50 ohms to Vcc – 2V or Thevenin equivalent.
4) Duty Cycle measured at 3.67V
ORDERING INFORMATION
FPHA554 - 155.52MHz
ECL
SERIES
CENTER
FREQUENCY
Specifications subject to change without notice.
DATA SHEET #: EC213
PAGE 1
OF
2
REV: 00
DATE: 01/26/05
aCopyright 2001 Connor-Winfield all rights reserved.
THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
HTTP://WWW.CONWIN.COM
PRODUCT
D ATA
SHEET
CRYSTAL CONTROLLED OSCILLATORS
CW DATE CODE
FPHA554
155.52M
Pin
1
2
3
4
5
6
7
8
9
10
Connection
N/C
Enable / Disable
N/C
Ground
N/C
Q Output
Q Output
N/C
Vcc
N/C
Dimensional Tolerance:
±.005 (.127mm)
SUGGESTED PAD LAYOUT
OUTPUT WAVEFORM
“1” LEVEL
“0” LEVEL
ENABLE/
DISABLE
Specifications subject to change without notice.
DATA SHEET #: EC213
PAGE 2
OF
2
REV: 01
DATE: 01/26/05
aCopyright 2001 Connor-Winfield all rights reserved.