THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. WWW.CONWIN.COM PRODUCT D AT A SHEET CRYSTAL CONTROLLED OSCILLATORS CW 0639 VSPLD63TE 622.08M 3.3V SURFACE MOUNT VCSO OSCILLATOR ABSOLUTE M AXIMUM RATING S PARAMETER TABLE 1.0 UNITS MINIMUM NOMINAL MAXIMUM UNITS -55 - 125 °C Storage Temperature Supply Voltage (Vcc) -0.5 - 7.0 Vdc Control Voltage (Vc) -0.5 - 7.0 Vdc MINIMUM NOMINAL MAXIMUM UNITS - 622.08 - MHz OPERATING SPECIFIC ATIONS NOTE DESCRIPTION TABLE 2.0 PARAMETER Center Frequency (Fo) Frequency Stability Operating Temperature Range - +/-150 - ppm -40 - 85 °C Vdc Supply Voltage (Vcc) 3.135 3.3 3.465 Supply Current (Icc) - - 80 mA Jitter (BW=10Hz to 20MHz) - - 3.0 ps rms Jitter (BW=12kHz to 80MHz) - - 0.5 ps rms SSB Phase Noise at 100Hz offset - -70 - dBc/Hz SSB Phase Noise at 1KHz offset - -105 - dBc/Hz SSB Phase Noise at 10KHz offset - -145 - dBc/Hz SSB Phase Noise at 100KHz offset - -155 - dBc/Hz MINIMUM NOMINAL MAXIMUM UNITS INPUT CHARACTERISTICS NOTE 1 TABLE 3.0 PARAMETER Control Voltage Range (Vc) NOTE 0.3 1.65 3.0 Vdc +/-50 - - ppm Gain Transfer (Kv) - 175 - ppm/volt Monotonic Linearity -15 - 15 % - 50K - Ohm 10 - - KHz 1.68 Vdc 3 - Vdc 3 Absolute Pull Range (APR) Input Impedance Modulation Bandwidth (3dB) Enable Input Voltage (Low) (Vil) - Disable Input Voltage (High) (Vih) 2.275 VSPLD63TE 2 The Connor-Winfield VSPLD63TE is a 3.3V Voltage Controlled SAW Oscillator (VCSO) with Differential LVPECL outputs and Enable/Disable function. The VSPLD63TE is designed for use with PLL systems in SONET/SDH systems requiring low jitter and wide pull range over the industrial temperature range. No multiplication schemes are used in this oscillator design. FEATURES VOLTAGE CONTROLLED SAW OSCILLATOR LOW PROFILE, SURFACE MOUNT PACKAGE 3.3V OPERATION LOW JITTER <0.5pS RMS ABSOLUTE PULL RANGE (APR): ±50ppm LOW VOLTAGE PECL OUTPUT CHARACTERISTICS PARAMETER MINIMUM NOMINAL MAXIMUM UNITS NOTE - - 50 Ohms 4 2.275 - - Vdc LOAD Voltage (High) (Voh) (Low) (Vol) Duty Cycle at 50% Level Rise and fall times (Measured 20% to 80%) PACKAG E CHARACTERISTICS TABLE 4.0 - - 1.68 Vdc 45 50 55 % - 250 400 ps PROCESS RECOMMENDATIONS Notes 1.0 2.0 3.0 4.0 TAPE AND REEL PACKAGING TABLE 6.0 Soldering Process Wash DIFFERENTIAL LVPECL OUTPUTS ENABLE / DISABLE FUNCTION TABLE 5.0 Non-hermetic package consisting of an FR4 substrate with grounded metal cover. Package TEMPERATURE RANGE: -40 to 85°C See solder profile page 2. Ultrasonic cleaning is not recommended. RoHS 5/6 COMPLIANT ORDERING INFORMATION VSPLD63TE - 622.08MHz I Frequency stability vs. change in temperature, control voltage (Vc) = 1.65 Vdc. Control voltage for (Fo) = 1.65 Vdc Typical. Positive Transfer Function. When oscillator is disabled the pin 4 output is in a low state (Vol) and the pin 5 output is in the high state (VoH) 50 ohm termination into Vcc-2V or Thevein equivalent. VCSO SERIES CENTER FREQUENCY Specifications subject to change without notice. DATA SHEET #: Vs001 PAGE 1 OF 2 REV: 01 DATE: 9/29/06 aCopyright 2001 Connor-Winfield all rights reserved. THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. WWW.CONWIN.COM PRODUCT D AT A SHEET CRYSTAL CONTROLLED OSCILLATORS Package Outline Pin Connections .140 MAX Pin 1 2 3 4 5 6 CW VSPLD63TE 622.08M (3.56mm) TABLE 7.0 Function Control Voltage Enable / Disable Ground (Case) Output Q Output Q Vcc Dimensional Tolerance: ±.005 (.127mm) Output Waveform Suggested Pad Layout Solder Profile Test Circuit Temperature 225°C Ramp-Up Rate 3°C/second max. from 150°C to 225°C. 225°C tp Ramp-Down Rate 6°C/second max. 183°C 150°C 100°C 2 25°C 1.65V 0 E/D Time 60-120s Max. 10-30s 60-150s Max. Vcc = Vcc2 = 3.3Vdc 360 Sec. Max. Specifications subject to change without notice. DATA SHEET #: Vs001 PAGE 2 OF 2 REV: 01 DATE: 9/29/06 aCopyright 2001 Connor-Winfield all rights reserved.