TI OPA356AQDBVRQ1

OPA356-Q1
www.ti.com.................................................................................................................................................................................................. SBOS479 – MARCH 2009
200-MHz CMOS OPERATIONAL AMPLIFIER
FEATURES
APPLICATIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
1
•
•
•
•
•
Qualified For Automotive Applications
Unity-Gain Bandwidth: 450 MHz
Wide Bandwidth: 200 MHz GBW
High Slew Rate: 360 V/s
Low Noise: 5.8 nV/√Hz
Excellent Video Performance
– Differential Gain: 0.02%
– Differential Phase: 0.05°
– 0.1-dB Gain Flatness: 75 MHz
Input Range Includes Ground
Rail-To-Rail Output (Within 100 mV)
Low Input Bias Current: 3 pA
Thermal Shutdown
Single-Supply Operating Range: 2.5 V To 5.5 V
•
•
•
Video Processing
Ultrasound
Optical Networking, Tunable Lasers
Photodiode Transimpedance Amplifiers
Active Filters
High-Speed Integrators
Analog-To-Digital (A/D) Converter Input
Buffers
Digital-To-Analog (D/A) Converter Output
Amplifiers
Barcode Scanners
Communications
DESCRIPTION
The OPA356 is a high-speed voltage-feedback CMOS operational amplifier designed for video and other
applications requiring wide bandwidth. The OPA356 is unity gain stable and can drive large output currents.
Differential gain is 0.02% and differential phase is 0.05°. Quiescent current is only 8.3 mA.
OPA356 is optimized for operation on single or dual supplies as low as 2.5 V (±1.25 V) and up to 5.5 V
(±2.75 V). Common-mode input range for the OPA356 extends 100 mV below ground and up to 1.5 V from V+.
The output swing is within 100 mV of the rails, supporting wide dynamic range.
The OPA356 is available in the SOT23-5 package and is specified over the –40°C to 125°C range.
DBV PACKAGE
(TOP VIEW)
Out 1
V+
5
–VIN
V+
Out
OPA356
V– 2
+VIN
+In 3
4
–In
V–
ORDERING INFORMATION (1)
PACKAGE (2)
TA
–40°C to 125°C
(1)
(2)
SOT-23 – DBV
Reel of 3000
ORDERABLE PART NUMBER
OPA356AQDBVRQ1
TOP-SIDE MARKING
OOVQ
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2009, Texas Instruments Incorporated
OPA356-Q1
SBOS479 – MARCH 2009.................................................................................................................................................................................................. www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range (unless otherwise noted)
VS
Supply voltage, V+ to V–
VIN
Signal input terminals voltage range
7.5 V
(2)
–0.5 V to (V+ + 0.5 V)
V– current (2)
10 mA
Output short-circuit duration (3)
Continuous
θJA
Thermal impedance, junction to free air (4)
TA
Operating free-air temperature range
–40°C to 125°C
TSTG
Storage temperature range
–65°C to 150°C
TJ
Junction temperature
160°C
TLEAD
Lead temperature (soldering, 10 s)
300°C
(1)
(2)
(3)
(4)
150°C/W
Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those specified is not implied.
Input terminals are diode-clamped to the power-supply rails. Input signals that can swing more than 0.5 V beyond the supply rails should
be current limited to 10 mA or less.
Short-circuit to ground one amplifier per package.
The package thermal impedance is calculated in accordance with JESD 51-5.
RECOMMENDED OPERATING CONDITIONS
MIN
MAX
VS
Supply voltage, V– to V+
2.7
5.5
V
TA
Operating free-air temperature
–40
125
°C
2
Submit Documentation Feedback
UNIT
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA356-Q1
OPA356-Q1
www.ti.com.................................................................................................................................................................................................. SBOS479 – MARCH 2009
ELECTRICAL CHARACTERISTICS
VS = 2.7 V to 5.5 V, RF = 604 Ω, RL = 150 Ω connected to VS/2 (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VS = 5 V, VCM = V– + 0.8 V
TA (1)
MIN
25°C
TYP
MAX
±2
±9
UNIT
VOS
Input offset voltage
ΔVOS/
ΔT
Offset voltage drift over
temperature
PSRR
Offset voltage drift vs
power supply
IB
Input bias current
IOS
Input offset current
Vn
Input voltage noise
density
In
Input current noise
density
VCM
Input common-mode
voltage range
CMRR
Input common-mode
rejection ratio
ZID
Differential input
impedance
25°C
1013 || 1.5
Ω || pF
ZICM
Common-mode input
impedance
25°C
1013 || 1.5
Ω || pF
AOL
Open-loop gain
Full range
Small-signal bandwidth
µV/°C
Full range
±7
25°C
±80
±350
µV/V
25°C
3
±50
pA
25°C
±1
±50
pA
f = 1 MHz
25°C
5.8
nV/√Hz
f = 1 MHz
25°C
50
fA/√Hz
VS = 2.7 V to 5.5 V,
VCM = VS/2 – 0.15 V
VS = 5.5 V, –0.1 V < VCM < 4 V
VS = 5 V, 0.3 V < VO < 4.7 V
25°C
V– – 0.1
25°C
66
Full range
66
25°C
84
Full range
80
G = +1, VO = 100 mVp-p, RF = 0 Ω
f–3dB
mV
±15
G = +2, VO = 100 mVp-p, RL = 50 Ω
G = +2, VO = 100 mVp-p, RL = 150 Ω
V+ – 1.5
80
V
dB
92
dB
450
100
25°C
MHz
170
G = +2, VO = 100 mVp-p, RL = 1 kΩ
200
GBW
Gain-bandwidth product
G = +10, RL = 1 kΩ
25°C
200
MHz
f0.1dB
Bandwidth for 0.1-dB
gain flatness
G = +2, VO = 100 mVp-p, RF = 560 Ω
25°C
75
MHz
SR
Slew rate
VS = 5 V, G = +2, 4-V output step
25°C
+300
–360
V/µs
trf
Rise-and-fall time
tsettle
Settling
time
0.1%
0.01%
Overload recovery time
Harmonic
distortion
Second
harmonic
Third
harmonic
G = +2, VO = 200 mVp-p, 10% to 90%
G = +2, VO = 2 Vp-p, 10% to 90%
VS = 5 V, G = +2, 2-V output step
VIN × Gain = VS
G = +2, f = 1 MHz, VO = 2 Vp-p,
RL = 200 Ω
2.4
25°C
25°C
30
25°C
120
25°C
8
25°C
–81
25°C
–93
NTSC, RL = 150 Ω
25°C
0.02
Differential phase error
NTSC, RL = 150 Ω
25°C
0.05
VS = 5 V, RL = 150 Ω, AOL > 84 dB
VS = 5 V, RL = 1 kΩ
0.2
25°C
(1)
(2)
Output
current (2)
Peak
ns
%
°
0.3
0.1
VS = 5 V, RL = 50 Ω
0.4
Continuous
IO
ns
dBc
Differential gain error
Voltage output swing
from rail
ns
8
V
0.6
±60
VS = 5 V
25°C
VS = 3 V
±100
mA
±80
Full range TA = –40°C to 125°C
See typical characteristic graph Output Voltage Swing vs Output Current.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA356-Q1
3
OPA356-Q1
SBOS479 – MARCH 2009.................................................................................................................................................................................................. www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
VS = 2.7 V to 5.5 V, RF = 604 Ω, RL = 150 Ω connected to VS/2 (unless otherwise noted)
PARAMETER
IQ
4
TEST CONDITIONS
TA (1)
MIN
TYP
Short-circuit current
25°C
+250
–200
Closed-loop output
impedance
25°C
0.02
25°C
8.3
Quiescent current
VS = 5 V, IO = 0
Thermal shutdown
junction temperature
Shutdown
Full range
Reset from shutdown
25°C
Submit Documentation Feedback
MAX
11
14
160
140
UNIT
mA
Ω
mA
°C
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA356-Q1
OPA356-Q1
www.ti.com.................................................................................................................................................................................................. SBOS479 – MARCH 2009
TYPICAL CHARACTERISTICS
TA = 25°C, VS = 5 V, G = +2, RF = 604 Ω, RL = 150 Ω connected to VS/2 (unless otherwise noted)
NON-INVERTING SMALL-SIGNAL
FREQUENCY RESPONSE
INVERTING SMALL-SIGNAL
FREQUENCY RESPONSE
6
3
VO = 0.1Vp-p
0
Normalized Gain (dB)
3
Normalized Gain (dB)
VO = 0.1Vp-p
G = +1
RF = 0
0
–3
G = +2
–6
G = +5
–9
G = +10
1M
–3
G = –5
G = –10
–9
10M
Frequency (Hz)
100M
–15
100k
1G
1M
NON-INVERTING SMALL-SIGNAL
STEP RESPONSE
100M
1G
G = +2
Output Voltage (500mV/div)
G = +2
Output Voltage (50mV/div)
10M
Frequency (Hz)
NON-INVERTING LARGE-SIGNAL
STEP RESPONSE
Time (20ns/div)
Time (20ns/div)
HARMONIC DISTORTION vs OUTPUT VOLTAGE
0.1dB GAIN FLATNESS FOR VARIOUS R F
–50
VO = 0.1Vp-p
CL = 0pF
0.4
RF = 604Ω
0.3
0.2
0.1
0
–0.1
RF = 560Ω
–0.2
–0.3
RF = 500Ω
–0.4
Harmonic Distortion (dBc)
0.5
Normalized Gain (dB)
G = –2
–6
–12
–12
–15
100k
G = –1
f = 1MHz
RL = 200Ω
–60
–70
2nd Harmonic
–80
3rd Harmonic
–90
–100
–0.5
1
10
Frequency (MHz)
100
0
1
2
Output Voltage (Vp-p)
3
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA356-Q1
4
5
OPA356-Q1
SBOS479 – MARCH 2009.................................................................................................................................................................................................. www.ti.com
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VS = 5 V, G = +2, RF = 604 Ω, RL = 150 Ω connected to VS/2 (unless otherwise noted)
HARMONIC DISTORTION vs INVERTING GAIN
HARMONIC DISTORTION vs NON-INVERTING GAIN
–50
VO = 2Vp-p
f = 1MHz
RL = 200Ω
–60
Harmonic Distortion (dBc)
Harmonic Distortion (dBc)
–50
–70
2nd Harmonic
–80
3rd Harmonic
–90
VO = 2Vp-p
f = 1MHz
RL = 200Ω
–60
–70
2nd Harmonic
–80
3rd Harmonic
–90
–100
–100
1
1
10
10
Gain (V/V)
Gain (V/V)
HARMONIC DISTORTION vs FREQUENCY
HARMONIC DISTORTION vs LOAD RESISTANCE
–60
–50
VO = 2Vp-p
RL = 200Ω
VO = 2Vp-p
f = 1MHz
Harmonic Distortion (dBc)
Harmonic Distortion (dBc)
–50
2nd Harmonic
–70
–80
3rd Harmonic
–90
–60
–70
–80
2nd Harmonic
–90
3rd Harmonic
–100
1M
Frequency (Hz)
10M
100
1k
RL (Ω)
FREQUENCY RESPONSE FOR VARIOUS R L
INPUT VOLTAGE AND CURRENT NOISE
SPECTRAL DENSITY vs FREQUENCY
3
RL = 10kΩ
10k
0
Normalized Gain (dB)
Voltage Noise (nV/ √Hz), Current Noise (fA/√Hz)
–100
100k
1k
Current Noise
Voltage Noise
100
10
–3
CL = 0pF
VO = 0.1Vp-p
RL = 50Ω
–6
RL = 150Ω
–9
RL = 1kΩ
–12
–15
100k
1
10
100
1k
10k
100k
1M
10M
100M
1M
10M
Frequency (Hz)
100M
1G
Frequency (Hz)
6
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA356-Q1
OPA356-Q1
www.ti.com.................................................................................................................................................................................................. SBOS479 – MARCH 2009
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VS = 5 V, G = +2, RF = 604 Ω, RL = 150 Ω connected to VS/2 (unless otherwise noted)
FREQUENCY RESPONSE FOR VARIOUS C L
RECOMMENDED RS vs CAPACITIVE LOAD
9
120
Normalized Gain (dB)
CL = 100pF
RS = 0Ω
VO = 0.1Vp-p
6
100
CL = 47pF
3
80
RS (Ω)
0
–3
CL = 5.6pF
60
VIN
RS
40
CL
20
–12
–15
100k
0
1M
10M
Frequency (Hz)
100M
1G
1
VO
CL
CL = 47pF
RS = 36Ω
1kΩ
604Ω
–12
(1kΩ is
Optional)
604Ω
–PSRR
80
RS
OPA356
–9
90
CL = 5.6pF
RS = 80Ω
CMRR, PSRR (dB)
VIN
–6
100
100
CL = 100pF
RS = 24Ω
–3
10
Capacitive Load (pF)
COMMON-MODE REJECTION RATIO AND
POWER-SUPPLY REJECTION RATIO vs FREQUENCY
G = +2
VO = 0.1Vp-p
0
(1kΩ is
Optional)
604Ω
FREQUENCY RESPONSE vs CAPACITIVE LOAD
3
Normalized Gain (dB)
1kΩ
604Ω
–9
+PSRR
70
60
CMRR
50
40
30
20
10
–15
1M
10M
100M
Frequency (Hz)
1G
0
10k
OPEN-LOOP GAIN AND PHASE
100k
1M
10M
Frequency (Hz)
100M
1G
COMPOSITE VIDEO
DIFFERENTIAL GAIN AND PHASE
180
0.40
160
RL = 1kΩ
140
120
0.35
Phase
100
dG/dP (%/degrees)
Open-Loop Phase (degrees)
Open-Loop Gain (dB)
VO
OPA356
–6
80
60
RL = 150Ω
40
Gain
20
0
0.30
0.25
0.20
dP
0.15
0.10
dG
0.05
–20
1k
10k
100k
1M
10M
Frequency (Hz)
100M
1G
0
1
2
3
Number of 150Ω Loads
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA356-Q1
4
7
OPA356-Q1
SBOS479 – MARCH 2009.................................................................................................................................................................................................. www.ti.com
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VS = 5 V, G = +2, RF = 604 Ω, RL = 150 Ω connected to VS/2 (unless otherwise noted)
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT
FOR V S = 3V
INPUT BIAS CURRENT vs TEMPERATURE
10n
25°C
1n
–55°C
Output Voltage (V)
Input Bias Current (pA)
3
100
10
2
125°C
Continuous currents above
60mA are not recommended
125°C
1
–55°C
25°C
1
–55
–35
–15
5
25
45
65
Temperature ( °C)
85
105 125 135
0
0
30
60
90
Output Current (mA)
120
150
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT
FOR V S = 5V
SUPPLY CURRENT vs TEMPERATURE
14
5
25°C
VS = 5.5V
–55°C
4
10
Output Voltage (V)
Supply Current (mA)
12
8
6
VS = 2.5V
VS = 3V
4
VS = 5V
2
125°C
3
Continuous currents above
60mA are not recommended
2
125°C
1
–55°C
25°C
0
–55
–35
–15
5
25
45
65
Temperature ( °C)
85
105 125 135
0
0
50
100
150
Output Current (mA)
200
250
MAXIMUM OUTPUT VOLTAGE vs FREQUENCY
CLOSED-LOOP OUTPUT IMPEDANCE vs FREQUENCY
100
6
10
Output Voltage (Vp-p)
Output Impedance (Ω)
VS = 5.5V
5
1
OPA356
0.1
604Ω
ZO
0.01
3
VS = 2.7V
2
1
604Ω
0.001
0
10k
8
Maximum Output
Voltage without
Slew-Rate
Induced Distortion
4
100k
1M
10M
Frequency (Hz)
100M
1G
1
Submit Documentation Feedback
10
Frequency (MHz)
100
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA356-Q1
OPA356-Q1
www.ti.com.................................................................................................................................................................................................. SBOS479 – MARCH 2009
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VS = 5 V, G = +2, RF = 604 Ω, RL = 150 Ω connected to VS/2 (unless otherwise noted)
OUTPUT SETTLING TIME TO 0.1%
OPEN-LOOP GAIN vs TEMPERATURE
110
0.2
VO = 2Vp-p
RL = 1kΩ
100
Open-Loop Gain (dB)
Output Error (%)
0.1
0
–0.1
–0.2
90
RL = 150Ω
80
70
–0.3
60
–0.4
0
5
10
15
20 25
30
Time (ns)
35
40
45
–55
50
OFFSET VOLTAGE PRODUCTION DISTRIBUTION
–15
5
25
45
65
Temperature ( °C)
85
105 125 135
COMMON-MODE REJECTION RATIO AND
POWER-SUPPLY REJECTION RATIO vs TEMPERATURE
20
100
18
16
Power-Supply Rejection Ratio
90
14
CMRR, PSRR (dB)
Percent of Amplifiers (%)
–35
12
10
8
6
4
80
Common-Mode Rejection Ratio
70
60
2
0
–9 –8 –7 –6 –5–4–3–2– 1 0 1 2 3 4 5 6 7 8 9
Offset Voltage (mV)
50
–55
–35
–15
5
25
45
65
Temperature ( °C)
85
105 125 135
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA356-Q1
9
OPA356-Q1
SBOS479 – MARCH 2009.................................................................................................................................................................................................. www.ti.com
APPLICATION INFORMATION
The OPA356 is a CMOS high-speed voltage-feedback operational amplifier designed for video and other
general-purpose applications.
The amplifier features a 200-MHz gain bandwidth and 360-V/µs slew rate, but it is unity-gain stable and can be
operated as a 1-V/V voltage follower.
Its input common-mode voltage range includes ground, allowing the OPA356 to be used in virtually any
single-supply application up to a supply voltage of 5.5 V.
PCB Layout
Good high-frequency PC board layout techniques should be employed for the OPA356. Generous use of ground
planes, short direct signal traces, and a suitable bypass capacitor located at the V+ pin assure clean, stable
operation. Large areas of copper also provide a means of dissipating heat that is generated within the amplifier in
normal operation.
Sockets are definitely not recommended for use with any high-speed amplifier.
A 10-µF ceramic bypass capacitor is the minimum recommended value; adding a 1-µF or larger tantalum
capacitor in parallel can be beneficial when driving a low-resistance load. Providing adequate bypass
capacitance is essential to achieving very low harmonic and intermodulation distortion.
Operating Voltage
The OPA356 is specified over a power-supply range of 2.7 V to 5.5 V (±1.35 V to ±2.75 V). However, the supply
voltage may range from 2.5 V to 5.5 V (±1.25 V to ±2.75 V). Supply voltages higher than 7.5 V (absolute
maximum) can permanently damage the amplifier.
Parameters that vary significantly over supply voltage or temperature are shown in the Typical Characteristics
section of this data sheet.
Output Drive
The OPA356 output stage is capable of driving a standard back-terminated 75-Ω video cable. By
back-terminating a transmission line, it does not exhibit a capacitive load to its driver. A properly back-terminated
75-Ω cable does not appear as capacitance; it presents only a 150-Ω resistive load to the OPA356 output.
The output stage can supply high short-circuit current (typically over 200 mA). Therefore, an on-chip thermal
shutdown circuit is provided to protect the OPA356 from dangerously high junction temperatures. At 160°C, the
protection circuit will shut down the amplifier. Normal operation will resume when the junction temperature cools
to below 140°C.
NOTE:
It is not recommended to run a continuous dc current in excess of ±60 mA. See the
"Output Voltage Swing vs Output Current" graph in the Typical Characteristics section
of this data sheet.
10
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA356-Q1
OPA356-Q1
www.ti.com.................................................................................................................................................................................................. SBOS479 – MARCH 2009
Input and ESD Protection
All OPA356 pins are static protected with internal ESD protection diodes tied to the supplies, as shown in
Figure 1. These diodes provide overdrive protection if the current is externally limited to 10 mA by the source or
by a resistor.
+V CC
External
Pin
Internal
Circuitry
–V CC
Figure 1. Internal ESD Protection
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): OPA356-Q1
11
PACKAGE OPTION ADDENDUM
www.ti.com
9-Sep-2011
PACKAGING INFORMATION
Orderable Device
OPA356AQDBVRQ1
Status
(1)
Package Type Package
Drawing
ACTIVE
SOT-23
DBV
Pins
Package Qty
5
3000
Eco Plan
(2)
Green (RoHS
& no Sb/Br)
Lead/
Ball Finish
MSL Peak Temp
(3)
Samples
(Requires Login)
CU NIPDAU Level-2-260C-1 YEAR
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF OPA356-Q1 :
• Catalog: OPA356
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
1-Dec-2011
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
OPA356AQDBVRQ1
Package Package Pins
Type Drawing
SPQ
SOT-23
3000
DBV
5
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
180.0
8.4
Pack Materials-Page 1
3.2
B0
(mm)
K0
(mm)
P1
(mm)
3.1
1.39
4.0
W
Pin1
(mm) Quadrant
8.0
Q3
PACKAGE MATERIALS INFORMATION
www.ti.com
1-Dec-2011
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
OPA356AQDBVRQ1
SOT-23
DBV
5
3000
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and Automotive www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
www.ti.com/video
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated