4.0x3.0mm RIGHT ANGLE SMD CHIP LED LAMP ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features APEKA4030TGC GREEN Description 4.0mmx3.0mm RIGHT ANGLE SMT LED, 2.65mm The Green source color devices are made with InGaN on SiC Light Emitting Diode. THICKNESS. LOW POWER CONSUMPTION. Static electricity and surge damage the LEDS. WIDE VIEWING ANGLE. It is recommended to use a wrist band or IDEAL FOR BACKLIGHT AND INDICATOR. anti-electrostatic glove when handling the LEDs. PACKAGE :500PCS / REEL. All devices, equipment and machinery must be RoHS COMPLIANT. electrically grounded. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.2(0.008") unless otherwise noted. 3. Specifications are subject to change without notice. SPEC NO: DSAD1188 REV NO: V.2 DATE: JUN/30/2005 PAGE: 1 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN ERP:1204000453 Selection Guide Part No. Dice APEKA4030TGC Iv (mcd) @ 20mA Lens Type GREEN (InGaN) WATER CLEAR Viewing Angle Min. Typ. 2θ θ1/2 50 100 90° Note: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device λpeak Peak Wavelength Green λD Dominant Wavelength ∆λ1/2 Typ. Max. Units Test Conditions 500 nm IF=20mA Green 505 nm IF=20mA Spectral Line Half-width Green 30 nm IF=20mA C Capacitance Green 56 pF VF=0V;f=1MHz VF Forward Voltage Green 3.6 4.4 V IF=20mA IR Reverse Current Green 10 uA VR = 5V Absolute Maximum Ratings at TA=25°C Parameter Green Units Power dissipation 110 mW DC Forward Current 30 mA Peak Forward Current [1] 150 mA 5 V Reverse Voltage Operating/Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAD1188 REV NO: V.2 DATE: JUN/30/2005 PAGE: 2 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN ERP:1204000453 Green APEKA4030TGC SPEC NO: DSAD1188 REV NO: V.2 DATE: JUN/30/2005 PAGE: 3 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN ERP:1204000453 APEKA4030TGC Recommended Soldering Pattern (Units : mm) Tape Specifications (Units : mm) SPEC NO: DSAD1188 REV NO: V.2 DATE: JUN/30/2005 PAGE: 4 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN ERP:1204000453 PACKING & LABEL SPECIFICATIONS APEKA4030TGC Remarks: If special sorting is required (e.g. binning based on forward voltage, luminous intensity, or wavelength), the typical accuracy of the sorting process is as follows: 1. Wavelength: +/-1nm 2. Luminous Intensity: +/-15% 3. Forward Voltage: +/-0.1V Note: Accuracy may depend on the sorting parameters. SPEC NO: DSAD1188 REV NO: V.2 DATE: JUN/30/2005 PAGE: 5 OF 5 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: H.Q.YUAN ERP:1204000453