OTS-4V8A Optiva Standard, 4 Composite Video and 8 Audio ® Composite Video and Audio Transmission The OTS-4V8A provides for the digital transmission of 4 Channels of Composite Video and 8 Channels of Analog Audio. Video Audio Data System Design ST, LC, SC or FC ST, LC, SC or FC Composite Video In Composite Video Out All units come in an insert card version. Composite Video In The cards can be inserted into our 16-slot, 19” rack-mountable card cage (OT-CC-16-100) or one of our smaller Optiva Desktop Card 8 Analog Racks (OT-DTCR Series). Audio In The Optiva® Desktop Card Racks can handle one, two or four insert cards, creating compact, mountable, stand alone systems. The use of separate OT-DTCR enclosures allows for future flexibility and expansion as all cards are hot-swappable and can be used in any enclosure. Each one of our card housing units operate with an appropriate power supply. See “Accessories” for power supply specifications. Composite Video Out A L E R T S T A T U S 8 Analog Audio Out Optiva™ Optiva™ VAD Transmission VAD Transmission OTS-4VT8AT OTS-4VR8AR Features • Composite Video and Analog Audio over one fiber • 12-Bit Digital Transmission (Video) Optiva Upgrade Path • TDM - Single Wavelength This system can be purchased without an optical port as an add-on to an existing Optiva® system daisy-chain. (See “Non-Optical Version” below). • Complies with SMPTE Standards The Optiva bandwidth requirement of this system is 1,444 Mbps. • Stand-alone or rack-mount ® ® A L E R T S T A T U S • Compatible with MDM-7000 Series for WDM and CWDM multiplexing • No EMI or RFI and no ground loops • Ideal for Professional AV applications Versions Available* Wavelength (nm) & Fiber Transmit** Receive** 1310 Multimode 1310 Singlemode 1310 Singlemode (D) 1550 Singlemode 1550 Singlemode (D) 1270-1610 SM (CWDM) OTS-4VT8AT-B1-XX-IC OTS-4VT8AT-B2-XX-IC OTS-4VT8AT-B2D-XX-IC OTS-4VT8AT-B3-XX-IC OTS-4VT8AT-B3D-XX-IC OTS-4VT8AT-L4-XX-IC OTS-4VR8AR-B1-XX-IC OTS-4VR8AR-B2-XX-IC OTS-4VR8AR-B2D-XX-IC OTS-4VR8AR-B3-XX-IC OTS-4VR8AR-B3D-XX-IC OTS-4VR8AR-L4-XX-IC Non-Optical Version OTS-4VT8AT-NOC-IC OTS-4VR8AR-NOC-IC Optical Connector Optical Budget (dB) Range*** (km) Form Factor ST, FC, LC or SC ST, FC, LC or SC ST, FC, LC or SC ST, FC, LC or SC ST, FC, LC or SC ST, FC, LC or SC 10 7 12 17 25 Varies 1.5 10 20 40 60 20-70 IC (3-slots) IC (3-slots) IC (3-slots) IC (3-slots) IC (3-slots) IC (3-slots) N/A N/A N/A IC (3-slots) Analog Audio Codes - To indicate your Analog Audio impedance preference, please use the following instead of "A" in the model number: "AB" = Input Balanced 600 Ohm, Output Balanced 600 Ohm; "ABH" = Input Balanced Hi-Z, Output Balanced Low-Z; and "AUH" = Input Unbalanced Hi-Z, Output Unbalanced Low-Z. * Contact Opticomm for other versions available. ** XX indicates the type of optical connector. Each of ST, FC, LC or SC are available. *** Chromatic dispersion and additional losses should be taken into account. 800-867-8426 • [email protected] • www.opticomm.com • Contact Opticomm for custom requirements. Opticomm reserves the right to change specifications without notice Composite Video, Audio & Data Video Standard Bit Resolution Level Bandwidth Differential Gain Differential Phase Passband Ripple Chroma/Luma Delay Compatibility Signal to Noise Ratio Connector Optiva™™Configurable Multi-Signal Optiva Transmission Platform Communication Platform SMPTE 170M; RS-250C (Short Haul) 12-Bit Digital Transmission 1.0 Volt p-p 5.5 MHz < 2% < 0.7° < ±0.2 dB to 5.5 MHz <12ns NTSC, PAL, SECAM > 67 dB BNC (IEC 60169-8) Network Management Management Network SDI HD-SDI SDIand & HD-SDI Composite Video, Video, Composite Audio & & Data Data Audio Audio/FSK/Intercom RGB/VGA/DVI RGB/VGA/DVI Audio/FSK/Intercom Data (Ethernet/Serial/USB) (Ethernet/Serial/USB) Data Analog Audio Level Bandwidth Signal to Noise Ratio Total Harmonic Distortion Signal Coding Connector General Dimensions & Weight Storage temperature Humidity Operating voltage Consumption System Latency Local Monitoring Remote Monitoring 6 dBm In/Out 20 Hz to 20 KHz > 80 dB < 0.1% 24-bit Micro DB25 Impedance Options: Input Balanced 600 Ohm Balanced Hi-Z Unbalanced Hi-Z Insert Card (IC): 6.3” L x 0.8” W x 4.0” H Operating temperature -20° C to +55° C -40° C to +85° C 0 to 95% non-condensing 9-12 VDC Output Balanced 600 Ohm Balanced Low-Z Unbalanced Low-Z 11 oz CATV/RF & & L-Band L-Band CATV/RF Optical Switching, Switching, Routing Routing Optical & Redundancy & Redundancy Passive Multiplexing Multiplexing Passive Solutions Solutions Enclosures, Racks Racks Enclosures, & Frames Frames & Power Supplies Supplies Power and Accessories & Accessories < 7w per insert card Less than 1ms (Audio <10ms) LED Status Indication Compatible with OptivaView™ SNMP Management Suite MADE IN THE USA Sample Configuration