54ACT11000, 74ACT11000 QUADRUPLE 2-INPUT POSITIVE-NAND GATES SCAS002A – D2957, JUNE 1987 – REVISED APRIL 1993 • • • • Inputs Are TTL-Voltage Compatible Flow-Through Architecture Optimizes PCB Layout Center-Pin VCC and GND Configurations Minimize High-Speed Switching Noise EPICt (Enhanced-Performance Implanted CMOS) 1-mm Process 500-mA Typical Latch-Up Immunity at 125°C Package Options Include Plastic Small-Outline Packages, Ceramic Chip Carriers, and Standard Plastic and Ceramic 300-mil DIPs description These devices contain four independent 2-input NAND gates. They perform the Boolean functions Y = ASB or Y = A + B in positive logic. The 54ACT11000 is characterized for operation over the full military temperature range of – 55°C to 125°C. The 74ACT11000 is characterized for operation from – 40°C to 85°C. FUNCTION TABLE (each gate) INPUTS 1B 2A 2B 3A 3B 4A 4B 1 (TOP VIEW) 1A 1Y 2Y GND GND 3Y 4Y 4B H H L L X H X L H 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 1B 2A 2B VCC VCC 3A 3B 4A 2A 1B NC 1A 1Y 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 3B 4A NC 4B 4Y 2Y GND NC GND 3Y B 1 54ACT11000 . . . FK PACKAGE (TOP VIEW) OUTPUT Y A NC – No internal connection logic symbol† 1A 54ACT11000 . . . J PACKAGE 74ACT11000 . . . D OR N PACKAGE 2B VCC NC VCC 3A • • logic diagram (positive logic) & 16 15 14 11 10 9 8 2 3 6 1A 1Y 2A 2Y 3Y 1Y 1B 2Y 2B 3A 3Y 3B 7 4Y 4A 4Y 4B † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Pin numbers shown are for the D, J, and N packages. EPIC is a trademark of Texas Instruments Incorporated. Copyright 1993, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 2–1 54ACT11000, 74ACT11000 QUADRUPLE 2-INPUT POSITIVE-NAND GATES SCAS002A – D2957, JUNE 1987 – REVISED APRIL 1993 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 6 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to VCC + 0.5 V Output voltage range, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to VCC + 0.5 V Input clamp current, IIK (VI < 0 or VI > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 20 mA Output clamp current, IOK (VO < 0 or VO > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 50 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 50 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 100 mA Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: The input and output voltage ratings may be exceeded if the input and output current ratings are observed. recommended operating conditions 54ACT11000 MAX MIN MAX 4.5 5.5 4.5 5.5 VCC VIH Supply voltage VIL VI Low-level input voltage Input voltage 0 VO IOH Output voltage 0 High-level output current IOL Dt /Dv Low-level output current TA Operating free-air temperature High-level input voltage 74ACT11000 MIN 2 2 0.8 Input transition rise or fall rate UNIT V V 0.8 V VCC VCC V – 24 – 24 mA 24 24 mA VCC VCC 0 0 V 0 10 0 10 ns/ V – 55 125 – 40 85 °C electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS IOH = – 50 mA VOH VOL IOH = – 24 mA VCC TA = 25°C MIN TYP MAX 54ACT11000 MIN MAX MIN 4.5 V 4.4 4.4 4.4 5.5 V 5.4 5.4 5.4 4.5 V 3.94 3.7 3.8 5.5 V 4.94 4.7 4.8 IOH = – 50 mA‡ IOH = – 75 mA‡ 5.5 V IOL = 50 mA 4.5 V UNIT V 3.85 0.1 0.1 5.5 V 0.1 0.1 0.1 4.5 V 0.36 0.5 0.44 5.5 V 0.36 0.5 0.44 0.1 V IOL = 50 mA‡ IOL = 75 mA‡ 5.5 V II ICC VI = VCC or GND VI = VCC or GND, 5.5 V ± 0.1 ±1 ±1 5.5 V 4 80 40 mA mA DICCw One input at 3.4 V,, Other inputs at GND or VCC 55V 5.5 09 0.9 1 1 mA Ci VI = VCC or GND 1.65 5.5 V IO = 0 5V 1.65 3.5 ‡ Not more than one output should be tested at a time, and the duration of the test should not exceed 10 ms. § This is the increase in supply current for each input that is at one of the specified TTL voltage levels rather than 0 V or VCC. 2–2 MAX 3.85 5.5 V IOL = 24 mA 74ACT11000 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 pF 54ACT11000, 74ACT11000 QUADRUPLE 2-INPUT POSITIVE-NAND GATES SCAS002A – D2957, JUNE 1987 – REVISED APRIL 1993 switching characteristics over recommended ranges of supply voltage and free-air temperature (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL A or B Y MIN TA = 25°C TYP MAX 54ACT11000 74ACT11000 MIN MAX MIN MAX 1.5 7.2 10.9 1.5 13.3 1.5 12.3 1.5 5.8 8 1.5 9.5 1.5 8.8 UNIT ns operating characteristics, VCC = 5 V, TA = 25°C PARAMETER Cpd TEST CONDITIONS Power dissipation capacitance per gate CL = 50 pF, f = 1 MHz TYP UNIT 23 pF PARAMETER MEASUREMENT INFORMATION 3V Input (see Note B) From Output Under Test CL = 50 pF (see Note A) 1.5 V 1.5 V 0V tPHL 500 Ω tPLH 50% VCC Output VOH 50% VCC VOL VOLTAGE WAVEFORMS LOAD CIRCUIT NOTES: A. CL includes probe and jig capacitance. B. Input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr = 3 ns, tf = 3 ns. C. The outputs are measured one at a time with one input transition per measurement. Figure 1. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 2–3 PACKAGE MATERIALS INFORMATION www.ti.com 17-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device 74ACT11000DR Package Package Pins Type Drawing SOIC D 16 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2500 330.0 16.4 Pack Materials-Page 1 6.5 B0 (mm) K0 (mm) P1 (mm) 10.3 2.1 8.0 W Pin1 (mm) Quadrant 16.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 17-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) 74ACT11000DR SOIC D 16 2500 333.2 345.9 28.6 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated