DC-AC INVERTER UNIT PS-DA0201-170-B(S) (10 W DUAL OUTPUTS) (PRELIMINARY INFORMATION) DESCRIPTION : This low profile DC to AC Inverter is developed for dual lamps. Optimized for Sharp: LQ150X1LG71_TL_LD-19251C 20070220 LQ150X1LG81_TL_LD-19356A 20070319 APPLICABLE LCD: 6.4 to 15 inches double lamp type Lamp Voltage 675 Vrms Lamp Current 2 x 6.5 mArms Lamp Start Up Voltage 1.680 Vrms (Vin : 12 Vdc) FEATURES : Remote ON/OFF Open Lamp Detection RoHS compliant (S) TEMPERATURE & HUMIDITY : Operating Temperature Range Storage Temperature Range Humidity DIMENSIONS : LxWxH 0°C ~ +60°C -40°C ~ +85°C 95 %RH max 160 x 25 x 12 mm Pin 1 Pin 1 Unit : mm Weight :24,2 (g) typ. Pin 1 Pin 1 Note: Please use plastic screw in case of a non-insulating mounting base! Components No. 1 2 Part Description PCB Connector CN1 Qty. 1 1 Material UL94V-0 (FR-4 or CEM-3) S5B-PH-K Note t=1m m JST or equal 3 Connector CN2 + CN3 2 SM02(8.0)B-BHS-1-TB JST or equal Output side CN2: Input side CN1: Pin No. CN 1-1 CN 1-2 CN 1-3 CN 1-4 Symbols Vin GND Vrm t Vbr Ratings 10.8 ~ 13.2 Vdc 0 ~ 0.4 = OFF / 2.5 ~ Vin = ON 0 ~ 2.5 Vdc CN 1-5 N.C. - Pin No. CN 2-1 Symbols Vhigh Ratings 675 Vrm s (6.5 m Arm s ) CN 2-2 Vlow (GND) Output side CN3: Pin No. CN 3-1 Symbols Vhigh Ratings 675 Vrm s (6.5 m Arm s ) CN 3-2 Vlow (GND) Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (1) Version 1.0.2; 7th July 2008 DC-AC INVERTER UNIT PS-DA0201-170-B(S) (10 W DUAL OUTPUTS) (PRELIMINARY INFORMATION) ELECTRICAL CHARACTERISTICS : Conditions Specification Parameters Symbols Output Current Output Current Input Current Frequency Open Circuit Voltage Iout Iout Iin F Vopen 12±1.2 12±0.6 12±1.2 12±1.2 11.4 0.0 2.5 0.0 0.0 0.0 0 0 0 0 0 Ts d 12±1.2 0.0 0 ~ +60 No load Shutdow n Note 1 : Vin (V) Vbr (V) Tu (°C) ~ +60 ~ +60 ~ +60 ~ +60 ~ +60 Unit Note 7.0 1.2 70 1.900 m Arm s % Adc kHz Vrm s Dut y 10 0% - s ec wit hout load Min. Typ. Max. 6.0 40 1.680 6.5 20 0.88 60 1.750 - 1.0 Dut y M in Please keep minimum of 2mm clearance (all directions) between inverter high voltage area as marked on mechanical drawing and any conductors. TEST CIRCUIT : F A Vin 12 V Iin 1000:1 PROBE F CN1-1 CN2-1 a V b Operation of unit a Operation b Non operation SW3 V CN1-2 Vrmt 0.4 / 5 Vdc SW 1 Vopen V ~ SW1 CN1-3 CL1 RL1 A ~ T1 CN2-2 SW4 Iout1 SW5 CN1-4 Vbr 0 ~ 2.5 Vdc CN3-1 CL2 RL2 N.C. CN1-5 CN3-2 SW6 A ~ Iout2 Power Systems – The Power Solution Web: Email: www.Power-Systems.de [email protected] All specifications are subject to change without notice. Address: Hauptstr. 48 ; 74360 Ilsfeld-Auenstein / Germany Tel. : + 49 / 70 62 / 67 59 - 6 Fax: + 49 / 70 62 / 67 59 - 800 Page (2) Version 1.0.2; 7th July 2008