60 km CWDM GbE SFP Transceiver SPC-GB-YX-xx Features • Data rate 1.062 to 1.25 Gb/s • 60 km reach • 22 dB min , 26 dB typical link budget • Commercial and Industrial temperature available • CWDM wavelength, DFB laser • SFP MSA SFF-8074i compatible • Digital Diagnostic SFF-8472 compatible • Telcordia GR-468 compliant • RoHS compliant General Operating Parameter Symbol Min. Typical Max. Unit Vcc 3.135 3.3 3.465 V Icc - - 500 mA Icc - - 300 mA IccR,IccT - - 300 mA Supply Voltage Total Current, -40 to 5ºCa Total Current, -5 to 85ºC Total Current each supply pin Power Supply Rejectionb PSR 100 - - mVp-p Operating temperature(-Cxx) Top -5 - 70 ºC Operating Temperature(-Txx) Top -40 - 85 ºC Storage Temperature Tst -40 - 85 ºC Data Rate GbE DR - 1250 - Mbps DR - 1062.5 - Mbps Data Rate FC a) Denotes deviation from MSA b) 20Hz to 155MHz Transmitter Specifications (Optical) Parameter Symbol Min Typical Max Unit Optical Power POP -2 0 3 dBm Average Launch Power Of Off Tx POff - - -30 dBm Extinction Ratio (Dynamic) ER 9 - - dB - - - 802.3z compliant Eye Mask Optical Jitter Random JR - - 147 ps Optical Jitter Deterministic JD - - 80 ps Total Jitter TJ - - 200 ps Optical Rise Timec tr - - 260 ps Optical Fall Timec tf - 260 ps Mean Wavelength Spectral Width (20dB) Side Mode Suppression Ratio Optical Path Penalty at 50 Kmd λ 1xx1-6.5nm 1xx1 1xx1+6.5nm nm ∆λ - - 1 nm SMSR 30 - - dB dp - 0.5 1 dB Relative Intensity Noise RIN - - -120 dB/Hz Reflection Tolerancee rp - - -24 dB c) 20%-80% values d) Measured at BER of 10-12 ,PRBS of 27 -1, at eye center e) 1 dB degardation of receiver sensitivity LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 1 LUMNDS1541-FEB2307 rev. A.1 60 km CWDM GbE SFP Transceiver SPC-GB-YX-xx Transmitter Specifications (Electical) Parameter Symbol Min Typical Max Unit Rin 80 100 120 Ω PECL Single Ended Data Input Swing Vin,p-p 250 - 1200 mV TxFault_Fault Vfault 2 - Vcc V Vnormal Vee - Vee+0.5 V Vd 2 - Vcc V Ven Vee - Vee+0.8 V Symbol Min Typical Max Unit Rsens,low - -26 -24 dBm Input Differential Impedence TxFault_Normal TxDisable_Disable TxDisable_Enable Receiver Specifications Parameter Receive Power Lowf Receive Power Highf Damage Threshold For Receiver Wavelength Reflection tolerance Rsens,high -3 0 - dBm Pin,damage 6 - - dBm λ 1200 - 1625 nm RX_r LOS Assert - - -12 dB -34 - - dBm - - -25 dBm 0.5 - - dB LOS De-assert LOS Hysteresis f)at 10-12 BER,27 -1 PRBS,nominal wavelength Electrical Output Parameter Symbol Min Typical Max Unit PECL Single Ended Data Output Swing Vout, p-p 185 - 800 mV Data Output Rise Time tr - - 320 ps Data Output Fall Time tf - - 320 ps Timing and Electrical Parameter Tx Disable Negate Time Tx Disable Assert Time Initial Turn-on Time after power-up Time To Initialize, Including Reset Of Tx Fault Symbol Min Typical Max Unit t_on - - 1 ms t_off - - 10 µs t_power-up - TBD 60 sec t_init - - 300 ms Tx Fault Assert Time t_fault - - 100 µs Tx Disable To Reset t_reset 10 - - µs t_loss_on - - 100 µs LOS Assert Time LOS De-assert Time t_loss_off - - 100 µs Serial ID Clock Rate f_serial_clock 2 - 100 KHz RX_LOS Voltage (High) 2 - Vcc V RX_LOS Voltage (Low) - - 0.8 V - - 170 ps Receiver Jitter Deterministic JD, receive Receiver Jitter Random JR, receive - - 96 ps MOD_DEF (0:2)-High VH 2 - Vcc V MOD_DEF (0:2)-Low VL Vee - Vee+0.5 V VLOS fault 2 - Vcc V VLOSnormal Vee - Vee+0.55 V LOS Output Voltage-Fault LOS Output Voltage-Normal LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2 LUMNDS1541-FEB2307 rev. A.1 60 km CWDM GbE SFP Transceiver SPC-GB-YX-xx λ Wavelength Ordering SPC-GB-YX-xx See table below for “XX” values λc Wavelength Guide Code λC Unit Code λC Unit Code λC Unit Code λC Unit 31 1311 nm 39 1391 nm 47 1471 nm 55 1551 nm 33 1331 nm 41 1411 nm 49 1491 nm 57 1571 nm 35 1351 nm 43 1431 nm 51 1511 nm 59 1591 nm 37 1371 nm 45 1451 nm 53 1531 nm 61 1611 nm Diagnostics Parameter Range Temperature(-CDx) -5 to 70 Accuracy Unit Calibration ±3 ºC Internal Temperature(-TDx) Formula Tc(C)=Tad(16 bit signed twos complement)/256 -40 to 85 ±3 ºC Internal Tc(C)=Tad(16 bit signed twos complement)/256 Voltage 0 to Vcc 0.1 V Internal V(Volts)=Vad(16 bit unsigned integer)*0.1 Bias Current 0 to 120 5 mA External I(mA)=Islope*Iad(16 bit unsigned integer)+Ioffset TX Power -2 to 3 ±3 dBm External TX_PWR(µW)=TX_PWRslope*TX_PWRad(16 bit unsigned integer +TX_PWRoffset RX Power -24 to -3 ±3 dBm External RX_PWR(µW)=A0+A1*x+A2*x^2+A3*x^3+A4*x^4 LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 3 LUMNDS1541-FEB2307 rev. A.1 60 km CWDM GbE SFP Transceiver SPC-GB-YX-xx EEPROM Serial ID Name of Field Vendor Name Vendor OUI Vendor PN LUMINENTOIC.COM Description of Field SFP Vendor Name(ASCII) IEEE Vendor OUI Code For LuminentOIC Inc. Part Number in ASCII, e.g. SPC-GB-YX-xxCDA Address Hex ASCII 20 4C L 21 55 U 22 4D M 23 49 I 24 4E N 25 45 E 26 4E N 27 54 T 28 4F O 29 49 I 30 43 C 37 00 38 06 39 B5 40 53 41 50 P 42 43 C 43 47 G 44 42 B 45 59 Y 46 58 X 47 x x 48 x x 49 43 C 50 44 D 51 41 A 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 4 S LUMNDS1541-FEB2307 rev. A.1 60 km CWDM GbE SFP Transceiver SPC-GB-YX-xx Pin Function Notes 1 VeeT TX GND 2 TX_FAULT Open Collector 3 TX_DISABLE Internally Pulled High 4 MOD_DEF2 Serial Data Input 5 MOD_DEF1 Serial Clock Input 6 MOD_DEF0 Internally Grounded 7 NC Not Connected 8 LOS Open Collector 9 VeeR RX Ground 10 VeeR RX Ground 11 VeeR RX Ground 12 RXD- RX Data Negative 13 RXD+ RX Data Positive 14 VeeR RX GND 15 VccT,R* Supply Voltage 16 VccT,R* Supply Voltage 17 VeeT TX GND 18 TXD+ TX Data Positive 19 TXD- TX Data Negative 20 VeeT TX GND *denotes deviations from MSA standard Outline Drawing Units in mm(inch) LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 5 LUMNDS1541-FEB2307 rev. A.1 60 km CWDM GbE SFP Transceiver SPC-GB-YX-xx Suggested Transceiver Interface 1H Vcc 10F 1H 0.1F VCCT .01F Protocol IC LuminentOIC SFP 10K R1 TX_DISABLE TX_DISABLE TX_FAULT TX_FAULT TD + SerDes Laser Driver .01F 100 TD VEET .01F VCCR 10F 0.1F RD + Receiver Amplifier .01F 100 RD - RX_LOS RX_LOS Vcc R VEER 1 R1 R1 .01F EEPROM R1 MOD_DEF 2 MOD_DEF 1 MOD_DEF 0 R1=47K to 10K LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 6 LUMNDS1541-FEB2307 rev. A.1 60 km CWDM GbE SFP Transceiver SPC-GB-YX-xx Ordering Inf ormation A vailable Options: SPC-GB-Y X-xxCDA SPC-GB-Y X-xxCNA SPC-GB-Y X-xxTDA SPC-GB-Y X-xxTNA Part numbering Definition: SPC - GB - Y X - xx Temperature Diagnostic Revision • SPC = Small Form Pluggable CW DM GB = 1.25 Gbps Y X = IEEE 802.3z Interface 60km • xx = CW DM W avelength • Operating Temperature C = Commeracial (-5 to 70) T = Industrial (-40 to 85) • D = Digital Diagnostic N = No Digital Diagnostic • Design Revision Warnings: Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notes: IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2003 All rights reserved LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 7 LUMNDS1541-FEB2307 rev. A.1