175 Watts LPS170 Series Total Power: 110-175 Watts Input Voltage: 85-264 VAC 120-300 VDC # of Outputs: Single Electrical Specs Input Input range Frequency Inrush current Efficiency EMI filter Power factor Safety ground leakage current Special Features • Active power factor correction • IEC EN61000-3-2 compliance • Wide Range Adjustable output Remote sense on main output • Single wire current sharing • Power fail and remote inhibit • Built-in EMI filter • Low output ripple • Overvoltage protection • Overload protection • Thermal overload protection • DC power good • 5 V standby output • 12 V Aux output • Optional cover (-C suffix) Environmental Operating temperature: 0° to 50°C ambientderate each output at 2.5% per degree from 50° to 70°C Maximum power Adjustment range Hold-up time Overload protection Overvoltage protection Standby output Aux output Power failure Remote inhibit Remote sense DC-OK Vibration: Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances 0.75 G peak 5 Hz to 500 Hz, operational Temperature coefficient: ± .04% per °C MTBF demonstrated: >550,000 hours at full load and 25°C ambient conditions 110 W convection (75 W with cover) 175 W with 30 CFM forced air (130 W with cover) 2:1 wide ratio minimum 20 ms @175 W load at nominal line Short circuit protection on all outputs. Case overload protected @ 110-145% above peak rating 10% to 40% above nominal output 5 V @ 2A regulated ±5% 12 V @ 1 A -5 %, +10% Logic Control 5% to 95% Storage temperature: -40° to 85°C 1.0 mA @ 50/60 Hz, 264 VAC input Output Electromagnetic susceptibility: designed to meet IEC EN61000-4, -2, -3, -4, -5, -6, -8, -11, Level 3 Humidity: Operating; non-condensing 85-264 VAC, 120-300 VDC 47-63 Hz 38 A max, cold start @ 25°C 75% typical at full load Meets FCC Class B conducted CISPR 22 Class B conducted EN55022 Class B conducted VDE 0878 PT3 Class B conducted 0.99 typical TTL logic signal goes high 100 - 500 msec after V1 output; It goes low at least 4 msec before loss of regulation Requires contact closure to inhibit outputs Compensates for 0.5 V lead drop min. Will operate without remote sense connected. Reverse connection protected. TTL logic signal goes high after main output is in regulation. It goes low when there is a loss of regulation Safety VDE UL CB CSA CE NEMKO 0805/EN60950 (IEC950) UL1950 Certificate and report CSA 22.2-234 Level 3 Mark (LVD) EN 60950/EMKO-TUE rev 08.09.03 118 Technical Support: (888) 41-ASTEC or (407) 241-2752 Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 AMERICAS EUROPE ASIA 5810 Van Allen Way Carlsbad, CA 92008 Telephone: 760-930-4600 Facsimile: 760-930-0698 Astec House, Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX, UK Telephone: 44 (1384) 842-211 Facsimile: 44 (1384) 843-355 Units 2111-2116, Level 21 Tower1, Metroplaza 223, Hing Fong Road Fwai Fong, New Territories Hong Kong Telephone: 852-2437-9662 Facsimile: 852-2402-4426 LPS170 Series Ordering Information Model Number Output Voltage Minimum Load Maximum Load with Convection Cooling Maximum Load with 30 CFM Forced Air Peak Load Regulation2 Ripple P/P(PARD)3 LPS172 LPS173 LPS174 LPS175 5 V (2.5-6V) 12 V (6-12 V) 15 V (12-24 V) 24 V (24-54 V) 0A 0A 0A 0A 22 A 9.1 A 7.3 A 4.5 A 35 A 15 A 12 A 7.5 A 38 A 16.5 A 13.2 A 8.2 A ±2% ±2% ±2% ±2% 50 mV 120 mV <1% <1% 1. Peak current lasting <30 seconds with a maximum 10% duty cycle. 2. At 25°C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with 20 MHz bandwidth and 10 µF in parallel with a 0.1 µF capacitor at rated line voltage and load ranges. 4. Remote inhibit resets OVP latch Note: -C suffix added to the model number indicates cover option. Ordering Information 1 5 6 LPS17x SK1 PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 PIN 8 PIN 9 PIN 10 +12V 5V Standby Common V1 SWP Common +V1 sense Sense common Remote inhibit DC power good POK SK3 TB-1 TB-2 COMMON Main output SK4 PIN 1 PIN 3 PIN 5 GROUND LINE NEUTRAL Mating Connectors (SK4) AC Input: - 10 SK1 Connector + SK3 1.50 (38.1) Voltage Adj POT 0.75 (19.0) 0.95 (24.0) 6.61 (168.0) 0.55 (14.0) 7.4 (188.0) 8.5 (216.0) Molex 09-50-8051 (USA) Molex 09-91-0500 (UK) PINS: 08-58-0111 (SK3) DC Output: Molex 19141-0058 5 3 1 (SK1) Control Signals: SK4 0.88 (22.2) 1.07 (27.2) Molex 90142-0010 (USA) PINS: 90119-2110 or Amp: 87977-3 PINS: 87309-8 M3 #6-32 Astec connector kit #70-841-016 4.25 (108.0) 2.50 (63.5) 2.11 (53.5) Notes: 1. Specifications subject to change without notice. 2. All dimensions in inches (mm), tolerance is ±0.02”. 3. Specifications are for convection rating at factory settings unless otherwise stated. 4. Mounting screw maximum insertion depth is 0.12”. 5. Warranty: 1 year 6. Weight: 1.8 lb / 0.85 kg #6-32(8 PLACES) M3(8 PLACES) www.astecpower.com 119