G.SHDSL Magnetics Globespan • TM01346 Designed to comply with the requirements of GR1089, UL1950, EN60950, BABT and CSA950 to provide a supplementary insulation barrier with a working voltage of 250V • UL File Number E150991 • Minimum interwinding breakdown voltage of 1500 Vrms • Operating and storage temperature range: -40° to +85° C • Meets IEC 695, 2-2 flammability requirements • PWB Process Capability: standard printed wiring board assembly techniques, total-immersion cleaning • Reliability testing: shock, vibration, temperature cycling, temperature - humidity - bias ELECTRICAL SPECIFICATIONS AT 25° C Turns Ratio ±2% Inductance1 mH ±5% 100mA DC Leakage Inductance2 µH max Chip : Line Line Side Line Side Chip Side 1 : 5.4 3 17 0.59 DCR Ω nom ±10% Interwinding Capacitance4 pF max Longitudinal Balance3 dB max Insertion Loss3 dB max Frequency Response3 dB max Harmonic Distortion3 dB max Line Side 1&8 20kHz 300kHz 100kHz 40kHz 300kHz 5kHz Fundamental 3.44 90 -55 0.75 0.30 -75 Part Number S560-6600-Z2 All measurements are made with pins 2 and 3 connected and pins 6 and 7 connected. 1. Inductance measured at 10kHz, 0.1 Vac. 2. Leakage inductance measured at 100 kHz, 0.1 Vac. Short terminals 5, 6, 7 and 8. 3. Measurements made with 135Ω source and 4.6Ω load impedance. 4. Interwinding capacitance measured at 10 kHz, 01Vac. SCHEMATIC S560-6600-Z2 Chip 8 1 6 7 3 5 4 2 Line ©2001 Bel Fuse Inc. Specifications subject to change without notice. 11.01 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com page 1 G.SHDSL Magnetics Globespan TM01346 MECHANICAL 1 2 3 0.098 [2.50] 0.048 [1.22] 4 S560-6600-Z2 0.615 [15.62] 8 7 6 5 0.077 [1.96] Suggested PCB Pad Layout 0.475 [12.07] max 0.510 [12.95] max 0.460 [11.68] max 0.492 [12.50] 0.024 [060] 0.098 [250] 0.004 [0.10] 8 Edges 0.600 [15.24] max Dimensions are in inches [millimeters]. Standard dimension tolerance is ±0.005 [0.13] unless otherwise noted. Tape and Reel Packaging 32 mm wide by 24 mm pitch; 13 inch OD, 4 inch ID 200 components per reel, maximum Meets ANSI/EIA 481-2 Carrier Tape Standards User Feed Direction Orientation of Component Inside Pocket ©2001 Bel Fuse Inc. Specifications subject to change without notice. 11.01 CORPORATE FAR EAST EUROPE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com Bel Fuse Ltd. 8F / 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com page 2