CEL UPB1508GV-E1-A

3.0 GHz
DIVIDE BY 2 PRESCALER
FEATURES
UPB1508GV
INTERNAL BLOCK DIAGRAM
• HIGH FREQUENCY OPERATION TO 3 GHz
• FIXED DIVIDE RATIO: ÷2
• LOW CURRENT CONSUMPTION: 12 mA at 5 V
IN
D
CLK
IN
CLK
• SMALL PACKAGE: 8 pin SSOP
• AVAILABLE IN TAPE AND REEL
Q
Q
OUT
AMP
DESCRIPTION
NEC's UPB1508GV is a Silicon RFIC digital prescaler manufactured with the NESAT™ IV silicon bipolar process. It features frequency response to 3 GHz, a divide-by-two ratio, and
operates on a 5 volt supply while drawing only 12 mA. The
device is housed in a small 8 pin SSOP package that contributes to system miniaturization. The low power consumption
and wide frequency operation makes the device well suited for
use in a PLL synthesizer for UHF/VHF TV and DBS tuner
applications.
ELECTRICAL CHARACTERISTICS (TA = -40 to +85°C, VCC = 4.5 to 5.5 V, ZS = ZL = 50 Ω)
PART NUMBER
PACKAGE OUTLINE
SYMBOLS
UNITS
MIN
TYP
MAX
Supply Current
mA
7.6
12
14.5
fIN (U)
Upper Limit Operating Frequency, PIN = -10 to +6 dBm
PIN = -15 to +6 dBm
GHz
GHz
3.0
2.7
fIN (L)
Lower Limit Operating Frequency, PIN = -15 to +6 dBm
GHz
Input Power, fIN = 2.7 to 3.0 GHz
fIN = 0.5 to 2.7 GHz
dBm
dBm
-10
-15
Output Power, PIN =0 dBm, fIN = 2 GHz
dBm
-12
ICC
PIN
POUT
PARAMETERS AND CONDITIONS
UPB1508GV
S08
0.5
+6
+6
-7
California Eastern Laboratories
UPB1508GV
ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C)
SYMBOLS
PARAMETERS
UNITS
RATINGS
RECOMMENDED
OPERATING CONDITIONS
VCC
Supply Voltage
V
6.0
SYMBOL
VIN
Input Voltage
V
6.0
VCC
Supply Voltage
PARAMETER
UNITS MIN TYP MAX
V
4.5
5.0
5.5
PT
Total Power Dissipation2
mW
250
TOP
Operating Temperature
°C
-40
+25
+85
TOP
Operating Temperature
°C
-40 to +85
TSTG
Storage Temperature
°C
-55 to +150
Notes:
1. Operation in excess of any one of these parameters may result
in permanent damage.
2. Mounted on a double-sided copper clad 50x50x1.6 mm epoxy
glass PWB (TA = +85˚C).
TEST CIRCUIT
Power Supply
1000 pF
Signal Generator
50 Ω
5 V ±0.5 V
1000 pF
C1
1000 pF
3
8 OPEN
1000 pF
7
C4
6 OPEN
4
5
1
2
C2
HP8665A
1000 pF
Counter HP5350B
(Spectrum Analyzer)
50 Ω
C3
PIN DESCRIPTIONS
Pin no.
Symbol
Applied
Voltage
Pin
Voltage
Description
1
VCC
4.5 to 5.5
2
IN
1.7 to 4.95
Signal input pin. This pin should be coupled with a capacitor (eg 1000 pF).
3
IN
1.7 to 4.95
Signal input bypass pin. This pin must be equipped with a bypass capacitor
(eg 1000 pF) to ground.
4, 5
GND
6
NC
7
OUT
8
NC
Power supply pin. This pin must be equipped with
bypass capacitor (eg 1000 pF) to ground.
0
Ground pin. Ground pattern on the board should be formed as wide as possible to
minimize ground impedance.
No connection. This pin should be left open.
1.0 to 4.7
Divided frequency output pin.
This pin should be coupled to load device with a capacitor (eg 1000 pF).
No connection. This pin should be left open.
UPB1508GV
TYPICAL PERFORMANCE CURVES (Unless otherwise specified, TA = 25°C)
INPUT POWER vs.
INPUT FREQUENCY and VOLTAGE
CIRCUIT CURRENT vs.
SUPPLY VOLTAGE and TEMPERATURE
+20
15
Input Power, PIN (dBm)
TA = +85 °C
Circuit Current, ICC (mA)
TA = +25 °C
+10
10
TA = +25 °C
TA = -40 °C
5
VCC = 4.5 to 5.5 V
0
Guaranteed
Operating
Window
-10
-20
VCC = 4.5 to 5.5 V
-30
-40
-50
0
-60
0
1
2
3
4
5
100
6
Supply Voltage, VCC (V)
INPUT POWER vs.
INPUT FREQUENCY and TEMPERATURE
+20
TA = +25 °C
TA = +85 °C
-10
Guaranteed
Operating
Window
TA = +85 °C
-20
-30
TA = +25 °C
TA = -40 °C
-40
VCC = 5.0 V
PIN = 0 dBm
ZL = 50 Ω
-2
Output Power, POUT (dBm)
Input Power, PIN (dBm)
0
TA = -40 °C
0
TA = +25 °C
-4
TA = -40 °C
TA = +85 °C
-6
TA = -40 °C
-8
TA = +85 °C
-10
TA = +25 °C
-12
-14
-50
-16
-60
100
1000
100
4000
1000
4000
Input Frequency, fin (MHz)
Input Frequency, fin (MHz)
OUTPUT POWER vs.
INPUT FREQUENCY and VOLTAGE
OUTPUT POWER vs.
INPUT FREQUENCY and VOLTAGE
0
0
VCC = 5.5 V
-4
VCC = 5.0 V
-6
TA = -40 °C
PIN = 0 dBm
ZL = 50 Ω
-2
Output Power, POUT (dBm)
TA = +25 °C
PIN = 0 dBm
ZL = 50 Ω
-2
Output Power, POUT (dBm)
4000
OUTPUT POWER vs.
INPUT FREQUENCY and VOLTAGE
VCC = 4.5 to 5.5 V
+10
1000
Input Frequency, fin (MHz)
VCC = 4.5 V
-8
-10
-12
-14
VCC = 5.5 V
-4
-6
VCC = 5.0 V
-8
VCC = 4.5 V
-10
-12
-14
-16
100
1000
Input Frequency, fin (MHz)
4000
-16
100
1000
Input Frequency, fin (MHz)
4000
UPB1508GV
TYPICAL PERFORMANCE CURVES (Unless otherwise specified, TA = 25 °C)
OUTPUT POWER vs.
INPUT FREQUENCY and VOLTAGE
0
Output Power, POUT (dBm)
-2
TA = +85 °C
PIN = 0 dBm
ZL = 50 Ω
VCC = 5.5 V
-4
-6
VCC = 5.0 V
-8
VCC = 4.5 V
-10
-12
-14
-16
100
1000
4000
Input Frequency, fin (MHz)
TYPICAL SCATTERING PARAMETERS (TA = 25 °C)
S11 vs. INPUT FREQUENCY
FREQUENCY
S11
VCC = 5.0 V
S11
Z
REF 1.0 Units
2
200.0 mUnits/
34.604 Ω -26.496 Ω
hp
C
D
MARKER 4
3.0 GHZ
4
1
3
2
START 0.500000000 GHz
STOP 3.000000000 GHz
1
: 0.5 GHz
2
: 1.0 GHz
3
: 2.0 GHz
4
: 3.0 GHz
GHz
MAG
ANG
0.5
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3.0
0.850
0.796
0.790
0.754
0.766
0.701
0.660
0.606
0.571
0.521
0.495
0.441
0.479
0.602
0.595
0.608
0.603
0.599
0.588
0.532
0.396
0.325
0.270
0.232
0.258
0.351
-30.2
-37.8
-39.2
-45.2
-53.7
-57.6
-62.3
-67.2
-70.3
-70.6
-68.3
-60.6
-45.1
-62.3
-74.2
-82.9
-89.8
-97.3
-107.7
-122.0
-132.0
-127.1
-123.6
-122.7
-105.8
-103.7
UPB1508GV
TYPICAL SCATTERING PARAMETERS (TA = 25 °C)
FREQUENCY
S22 vs. OUTPUT FREQUENCY
VCC = 5.0 V, fin = 498 MHz
S22
Z
REF 1.0 Units
2
200.0 mUnits/
87.789 Ω -13.633 Ω
hp
C
D
MARKER 4
1.5 GHZ
1
2
3
4
1
: 0.25 GHz
2
: 0.50 GHz
3
: 1.00 GHz
4
: 1.50 GHz
START 0.250000000 GHz
STOP 1.500000000 GHz
S22
GHz
MAG
ANG
0.25
0.30
0.35
0.40
0.45
0.50
0.55
0.60
0.65
0.70
0.75
0.80
0.85
0.90
0.95
1.00
1.05
1.10
1.15
1.20
1.25
1.30
1.35
1.40
1.45
1.50
0.526
0.463
0.466
0.460
0.441
0.456
0.353
0.438
0.444
0.436
0.435
0.431
0.431
0.431
0.408
0.445
0.428
0.429
0.355
0.418
0.403
0.392
0.368
0.343
0.319
0.289
118.9
131.2
124.7
117.1
110.2
103.0
94.8
91.1
83.9
78.3
71.8
65.9
60.3
53.7
49.2
44.9
41.0
33.7
42.7
20.0
17.1
9.6
3.3
-3.4
-9.2
-14.1
S22 vs. OUTPUT FREQUENCY
FREQUENCY
VCC = 5.0 V, fin = 3002 MHz
S22
Z
REF 1.0 Units
2
200.0 mUnits/
91.109 Ω 2.6523 Ω
hp
C
D
MARKER 4
1.5 GHZ
2
3
1
4
START 0.250000000 GHz
STOP 1.500000000 GHz
1
: 0.25 GHz
2
: 0.50 GHz
3
: 1.00 GHz
4
: 1.50 GHz
S22
GHz
MAG
ANG
0.25
0.30
0.35
0.40
0.45
0.50
0.55
0.60
0.65
0.70
0.75
0.80
0.85
0.90
0.95
1.00
1.10
1.15
1.20
1.25
1.30
1.35
1.40
1.45
1.50
0.555
0.545
0.571
0.529
0.521
0.515
0.510
0.492
0.487
0.482
0.473
0.461
0.454
0.449
0.430
0.443
0.440
0.438
0.501
0.408
0.388
0.359
0.335
0.304
0.285
146.6
139.9
136.1
127.9
122.4
116.9
104.5
106.6
100.9
95.3
89.9
83.8
78.4
72.3
69.6
64.3
52.3
46.0
37.5
32.9
25.1
16.3
9.7
3.1
4.6
UPB1508GV
SYSTEM APPLICATION EXAMPLE
1st IF Input from
DBS Converter
Baseband Output
MIX
SAW
BPF
AGC Amp. FM Demo.
UPB1508GV
+2
Prescaler
OSC
PLLsynth.
for
VHF/UHF
band
LPF
PIN CONNECTION
OUTLINE DIMENSIONS (Units in mm)
PACKAGE OUTLINE S08
7
8
6
5
1508
2
3
3.0 MAX
8
2
7
3
6
4
5
Detail of Lead End
N
1
1
+7˚
4
3 -3˚
4.94 ± 0.2
+0.10
0.15 -0.05
1.5±0.1
0.87±0.2
3.2±0.1
1.8 MAX
0.1 ± 0.1
0.65
+0.10
0.3 -0.05
0.5 ± 0.2
0.575 MAX
0.15
PIN CONNECTIONS
1. VCC
5. GND
2. IN
6. NC
3. IN
7. OUT
4. GND
8. NC
ORDERING INFORMATION
PART NUMBER
QUANTITY
UPB1508GV-E1-A
1000/Reel
Note:
1. Embossed tape 8 mm wide.
Pin 1 is in the tape pull-out direction.
Life Support Applications
These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably
be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and
agree to fully indemnify CEL for all damages resulting from such improper use or sale.
EXCLUSIVE NORTH AMERICAN AGENT FOR
RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS
CALIFORNIA EASTERN LABORATORIES • Headquarters • 4590 Patrick Henry Drive • Santa Clara, CA 95054-1817 • (408) 988-3500 • Telex 34-6393 • FAX (408) 988-0279
24-Hour Fax-On-Demand: 800-390-3232 (U.S. and Canada only) • Internet: http://WWW.CEL.COM
DATA SUBJECT TO CHANGE WITHOUT NOTICE
09/21/2000
4590 Patrick Henry Drive
Santa Clara, CA 95054-1817
Telephone: (408) 919-2500
Facsimile: (408) 988-0279
Subject: Compliance with EU Directives
CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant
with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous
Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive
2003/11/EC Restriction on Penta and Octa BDE.
CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates
that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are
exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals.
All devices with these suffixes meet the requirements of the RoHS directive.
This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that
go into its products as of the date of disclosure of this information.
Restricted Substance
per RoHS
Concentration Limit per RoHS
(values are not yet fixed)
Concentration contained
in CEL devices
-A
Not Detected
Lead (Pb)
< 1000 PPM
Mercury
< 1000 PPM
Not Detected
Cadmium
< 100 PPM
Not Detected
Hexavalent Chromium
< 1000 PPM
Not Detected
PBB
< 1000 PPM
Not Detected
PBDE
< 1000 PPM
Not Detected
-AZ
(*)
If you should have any additional questions regarding our devices and compliance to environmental
standards, please do not hesitate to contact your local representative.
Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance
content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information
provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better
integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate
information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL
suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for
release.
In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to
customer on an annual basis.
See CEL Terms and Conditions for additional clarification of warranties and liability.