NEC UPB1511TB-E3

800 MHz INPUT DIVIDE BY 2, 4 PRESCALER IC, UPB1511TB
FOR PORTABLE SYSTEMS
FEATURES
TEST CIRCUIT
• SUPPLY VOLTAGE
VCC = 2.4 to 3.3 V
• OPERATING FREQUENCY
fIN = 50 to 700 MHz at ÷ 2
50 to 800 MHz at ÷ 4
1 000 pF
• LOW CURRENT CONSUMPTION
3.5 mA at VCC = 3.0 V
3 SW
IN
4
2 GND
IN
5
1 OUT
Vcc
6
1 000 pF
• SELECTABLE DIVISION
÷ 2, ÷ 4
• HIGH-DENSITY SURFACE MOUNTING
6-pin super minimold
1 000 pF
1 000 pF
1 000 pF
DESCRIPTION
Power Supply
The UPB1511TB is a silicon monolithic integrated circuit
designed as a divide by 2,4 prescaler IC for portable radio
systems. This IC is manufactured using NEC's 30 GHz fMAX
UHS0 (Ultra High Speed Process) silicon bipolar process.
Consequently, this IC is lower circuit current and smaller
package than conventional UPB1509GV. The low power makes
this device ideally suited for cellular and cordless telephone
applications.
APPLICATIONS
• Portable radio systems
• Cellular/cordless telephone 2nd local prescaler
NEC's stringent quality assurance and test procedures ensure
the highest reliability and performance.
ELECTRICAL CHARACTERISTICS (TA = +25°C, VCC = 3.0 V)
PART NUMBER
PACKAGE OUTLINE
SYMBOLS
UPB1511TB
UNITS
MIN
TYP
MAX
Circuit Current, No Signals
mA
3.1
3.5
4.1
fIN (u)1
Upper Limit Operating Frequency 1, PIN = -20 to 0 dBm
MHz
500
fIN (u)2
Upper Limit Operating Frequency 2, PIN = -20 to -5 dBm @ ÷ 2
MHz
700
ICC
PARAMETERS AND CONDITIONS
@ ÷4
fIN (L)1
Lower Limit Operating Frequency 1, PIN = -20 to 0 dBm
fIN (L)2
800
MHz
50
Lower Limit Operating Frequency 2, PIN = -20 to -5 dBm
MHz
PIN1
Input Power 1, fIN = 50 to 800 MHz
dBm
-20
500
-5
PIN2
Input Power 2, fIN = 50 to 500 MHz
dBm
-20
0
VOUT
Output Voltage, RL = 200 Ω
VP-P
0.2
VIH
Divide Ratio Control Input High
V
0.7 x VCC
0.3
VCC + 0.5
VIL
Divide Ratio Control Input Low
V
-0.5
VCC x 0.3
California Eastern Laboratories
UPB1511TB
ABSOLUTE MAXIMUM RATINGS1
SYMBOLS
UNITS
RATINGS
Supply Voltage
TA = +25° C
V
3.6
VIN
Input Voltage
TA = +25° C, SW Pin
V
3.6
PD
Total Power Dissipation2
(TA = +85° C)
mW
200
TA
Operating Ambient Temp.
°C
-40 to +85
Storage Temperature
°C
-55 to +150
VCC
TSTG
PARAMETERS
RECOMMENDED
OPERATING CONDITIONS
SYMBOLS
PARAMETERS
VCC
TA
UNITS MIN
TYP MAX
Supply Voltage
V
2.4
3.0
3.3
Operating Ambient Temp.
°C
-40
+25
+85
SYSTEM APPLICATION EXAMPLE
Notes:
1. Operation in excess of any one of these conditions may result in
permanent damage.
2. Mounted on double sided copper clad 50 x 50 x 1.6mm epoxy
glass PWB
LNA
RX
DEMOD.
I
Q
VCO
VCO
÷N
PLL
PLL
SW
÷N
UPB1511TB
INTERNAL BLOCK DIAGRAM
I
0˚
Phase
Shifter
90˚
TX
Q
D
Q
D
PA
Q
IN
CLK
IN
CLK
Q
OUT
Q
SW
PRODUCT LINE-UP
PART NUMBER
ICC
VCC
÷2
÷4
÷8
(mA)
(V)
fIN
(MHZ)
fIN
(MHZ)
fIN
(MHZ)
PACKAGE
UPB1509 GV
5.0
2.2 to 5.5
50 to 700
50 to 800
50 to 1000
8-pin SSOP
UPB1511 TB
3.5
2.4 to 3.3
50 to 700
50 to 800
-
6-pin super minimold
PIN EXPLANATIONS
PIN NO.
SYMBOL
APPLIED
VOLTAGE (V)
FUNCTIONS AND EXPLANATION
1
OUT
–
Divided Frequency Output Pin. This pin is designed as an emitter follower output
and can deliver 0.2 VP-P minimum into a 200 Ω load.
This pin should be coupled to the load device with a capacitor (example: 1000 pF)
for DC cut.
2
GND
0
Ground Pin. Ground pattern on the board should be as wide as possible to
minimize ground impedance.
3
SW
H/L
Divide Ratio Control Pin. Divide ratio can be determined by the following applied
level to these pins.
SW
Divide ratio
H
1/2
L
1/4
These pins must be each equipped with bypass capacitor to minimize
their impedance.
4
IN
–
Signal Input Pin. This pin should be coupled to the signal source with a capacitor
(example: 1000 pF) for DC cut.
5
IN
–
Signal Input Bypass Pin. This pin must be equipped with a bypass capacitor
(example: 1000 pF) to minimize ground impedance.
6
VCC
2.4 TO 3.3
Power Supply Pin. This pin must be equipped with a bypass capacitor
(example: 1000 pF) to minimize ground impedance.
UPB1511TB
OUTLINE DIMENSIONS (Units in mm)
PIN CONNECTIONS
(Top View)
6-PIN SUPER MINIMOLD
(Bottom View)
3
1.25 ±0.1
0.2 ±0.1
1.3
1
0.65
2.0 ±0.2
0.65
2
4
3
5
5
2
6
6
1
0.7
0.9 ±0.1
0.15 +0.1
-0
0 to 0.1
ORDERING INFORMATION
TEST CIRCUIT
1 000 pF
3 SW
IN
4
2 GND
IN
5
1 OUT
Vcc
50 Ω
1 000 pF
Oscilloscope
4
PIN CONNECTION
1. OUT
2. GND
3. SW
4. IN
5. IN
6. VCC
0.1 MIN
High Impedance
C2Z
2.1 ±0.1
1 000 pF
150 Ω
PART NUMBER
PACKAGE
QUANTITY
UPB1511TB-E3
6-pin super minimold
Qty 3 kpcs/reel.
Notes:
1. Embossed tape 8 mm wide. Pin 1, 2, 3 face the tape perforation
side.
Signal Generator
1 000 pF
6
1 000 pF
50 Ω
Power Supply
Counter
(or Spectrum Analyzer)
Divide Ratio Setting
SW
H
1/2
L
1/4
Life Support Applications
These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably
be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and
agree to fully indemnify CEL for all damages resulting from such improper use or sale.
EXCLUSIVE NORTH AMERICAN AGENT FOR NEC RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS
CALIFORNIA EASTERN LABORATORIES • Headquarters • 4590 Patrick Henry Drive • Santa Clara, CA 95054-1817 • (408) 988-3500 • Telex 34-6393 • FAX (408) 988-0279
Internet: http://WWW.CEL.COM
DATA SUBJECT TO CHANGE WITHOUT NOTICE
07/18/2002