UPB1510GV 3.0 GHz DIVIDE BY 4 PRESCALER TEST CIRCUIT FEATURES • HIGH FREQUENCY OPERATION TO 3 GHz Power Supply • FIXED DIVIDE RATIO: ÷ 4 1000 pF • LOW CURRENT CONSUMPTION: 15 mA at 5 V 5 V ± 0.5 V • SMALL PACKAGE: 8 PIN SSOP • AVAILABLE IN TAPE AND REEL 1000 pF C1 RFIN 1 8 OPEN 2 7 1000 pF 2200 pF DESCRIPTION 1000 pF NEC's UPB1510GV is a Silicon RFIC digital prescaler manufactured with the NESAT™ IV silicon bipolar process. It features frequency response to 3 GHz, a divide-by-four ratio, and operates on a 5 volt supply while drawing only 15 mA. The device is housed in a small 8 pin SSOP package that contributes to system miniaturization. The low power consumption and wide frequency operation makes the device well suited for use in a PLL synthesizer for UHF/VHF TV and DBS tuner applications. OUT C4 C2 3 6 OPEN 4 5 C3 ELECTRICAL CHARACTERISTICS (TA = -40 to +85°C, VCC = 4.5 to 5.5 V, ZS = ZL = 50 Ω) PART NUMBER PACKAGE OUTLINE SYMBOLS ICC PARAMETERS AND CONDITIONS UPB1510GV S08 UNITS MIN TYP MAX 14 17 Circuit Current, No Input Signal mA 10.5 fIN (u)1 Upper Limit Operating Frequency 1, PIN = -10 to +6 dBm GHz 3.0 fIN (u)2 Upper Limit Operating Frequency 2, PIN = -15 to +6 dBm GHz 2.7 fIN (L) Lower Limit Operating Frequency, PIN = -15 to +6 dBm GHz PIN1 Input Power 1, fIN = 2.7 to 3.0 GHz dBm -10 0.5 PIN2 Input Power 2, fIN = 1.0 to 2.7 GHz dBm -15 POUT Output Power, PIN = 0 dBm, fIN = 2.0 GHz dBm -12 +6 +6 -7 California Eastern Laboratories UPB1510GV ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C) SYMBOLS PARAMETERS UNITS RATINGS RECOMMENDED OPERATING CONDITIONS VCC Supply Voltage V 6.0 SYMBOL VIN Input Voltage V 6.0 VCC PD Total Power Dissipation2 mW 250 TA TA Operating Ambient Temp. °C -40 to +85 Storage Temperature °C -55 to +150 TSTG PARAMETER UNITS MIN TYP MAX Supply Voltage V 4.5 5.0 5.5 Operating Ambient Temp. °C -40 +25 +85 Notes: 1. Operation in excess of any one of these parameters may result in permanent damage. 2. Mounted on a double-sided copper clad 50x50x1.6 mm epoxy glass PWB (TA = +85˚C). INTERNAL BLOCK DIAGRAM IN D CLK IN CLK D CLK Q Q CLK Q Q OUT AMP SYSTEM APPLICATION EXAMPLE RF UNIT BLOCK OF DBS TUNER 1st IF Input from DBS converter MIX Baseband Output SAW BPF UPB1510GV ÷4 Prescaler OSC AGC amp FM demo PLL synth. for VHF/UHF band LPF PIN DESCRIPTIONS Pin No. Symbol Applied Voltage Description 1 VCC 4.5 to 5.5 1000 pF). Power supply pin. This pin must be decoupled with a bypass capacitor (e.g. 2 IN – Signal input pin. This pin should be coupled to source with a capacitor (e.g. 1000 pF). 3 IN – Signal input bypass pin. This pin must be equipped with a bypass capacitor (e.g. 1000 pF) to ground. 4 GND 0 Ground pin. Ground pattern on the board should be formed as wide as possible to minimize ground impedance. 5 GND 0 6 NC – No connection, this pin should be left open. 7 OUT – Divided frequency output pin. This pin is designed as an emitter follower output, and should be coupled to the load with a capacitor (e.g. 1000 pF). 8 NC – No connection, this pin should be left open. UPB1510GV TYPICAL PERFORMANCE CURVES (TA = +25°C unless otherwise noted) CURRENT vs. VOLTAGE and TEMPERATURE INPUT POWER vs. INPUT FREQUENCY and VOLTAGE +20 20 TA = +25°C No input signal Input Power, PIN (dBm) Circuit Current, ICC (mA) +10 15 TA = +25°C 10 TA = +85°C TA = -40°C 5 0 Guaranteed operating range -10 -20 VCC = 4.5 to 5.5 V -30 -40 0 -50 0 1 2 4 3 5 6 0.1 7 Supply Voltage, VCC (V) INPUT POWER vs. INPUT FREQUENCY and TEMPERATURE +20 0.5 1 3 10 Input Frequency, fin (GHz) OUTPUT POWER vs. INPUT FREQUENCY and VOLTAGE 0 TA = -40°C TA = 25°C TA = 85°C 0 TA = 85°C -10 Output Power, POUT (dBm) Input Power, PIN (dBm) +10 Guaranteed operating range TA = 25°C -20 -30 TA = -40°C TA = 85°C -5 TA = 25°C TA = -40°C -10 VCC = 5 V PIN = 0 dBm ZL = 50 W -40 VCC = 5 V -50 -15 0.1 0.5 3 1 0.1 10 1 3 10 Input Frequency, fin (GHz) Input Frequency, fin (GHz) OUTPUT POWER vs. INPUT FREQUENCY and VOLTAGE OUTPUT POWER vs. INPUT FREQUENCY and VOLTAGE 0 Output Power, POUT (dBm) 0 Output Power, POUT (dBm) 0.5 VCC = 5 V VCC = 5.5 V -5 VCC = 4.5 V -10 VCC = 5 V VCC = 5.5 V -5 VCC = 4.5 V -10 TA = 25°C PIN = 0 dBm ZL = 50 Ω TA = -40°C PIN = 0 dBm ZL = 50 Ω -15 0.1 0.5 1 3 Input Frequency, fin (GHz) 10 -15 0.1 0.5 1 3 Input Frequency, fin (MHz) 10 UPB1510GV TYPICAL PERFORMANCE CURVES (TA = +25°C unless otherwise noted) OUTPUT POWER vs. INPUT FREQUENCY and VOLTAGE Output Power, POUT (dBm) 0 VCC = 5 V VCC = 5.5 V -5 VCC = 4.5 V -10 TA = 85°C PIN = 0 dBm ZL = 50 Ω -15 0.1 0.5 1 3 10 Input Frequency, fin (GHz) TYPICAL SCATTERING PARAMETERS (TA = 25°C) S11 vs. INPUT FREQUENCY VCC = 5.0 V, TA = 25°C, ZO = 50 Ω S11 Z REF 1.0 Units 4 200.0 mUnits/ 27.159 Ω -27.582 Ω hp MARKER 4 3 GHz 4 1 3 START 0.500000000 GHz STOP 3.000000000 GHz 2 1 : 500 MHz 2 : 1000 MHz 3 : 2000 MHz 4 : 3000 MHz FREQUENCY MHz S11 (Ω) 500 1000 2000 3000 37.1 - j207.8 14.2 - j105.1 7.9 - j35.8 27.1 - j27.5 UPB1510GV TYPICAL SCATTERING PARAMETERS (TA = 25°C) S22 vs. OUTPUT FREQUENCY VCC = 5.0 V, fin = 500 MHz, TA = 25°C, ZO = 50 Ω S22 Z REF 1.0 Units 4 200.0 mUnits/ 60.925 Ω 104.77 Ω hp MARKER 4 750 MHz 4 3 : 125 MHz 1 2 2 : 250 MHz 1 3 : 500 MHz 4 : 750 MHz FREQUENCY MHz S22 (Ω) 125 250 500 750 55.5 + j6.7 53.7 + j30.4 55.0 + j60.3 60.9 + j104.8 START 0.125000000 GHz STOP 0.750000000 GHz S22 vs. OUTPUT FREQUENCY VCC = 5.0 V, fin = 3 GHz, TA = 25°C, ZO = 50 Ω S22 Z REF 1.0 Units 4 200.0 mUnits/ 15.613 Ω 98.168 Ω hp 4 MARKER 4 750 MHz 3 2 1 START 0.125000000 GHz STOP 0.750000000 GHz 1 : 125 MHz 2 : 250 MHz 3 : 500 MHz 4 : 750 MHz FREQUENCY MHz S22 (Ω) 125 250 500 750 28.5 + j11.5 27.6 + j23.6 20.5 + j50.7 15.6 + j98.2 UPB1510GV OUTLINE DIMENSIONS (Units in mm) PACKAGE OUTLINE S08 8 7 6 5 1510 1 2 3 3.0 MAX Detail of Lead End 4.94 ± 0.2 +0.10 0.15 -0.05 0.87±0.2 3.2±0.1 1.8 MAX 0.1 ± 0.1 0.65 +0.10 0.3 -0.05 8 2 7 3 6 4 5 +7˚ 3 -3˚ 4 1.5±0.1 1 0.5 ± 0.2 0.575 MAX 0.15 PIN CONNECTIONS 1. VCC 5. GND 2. IN 6. NC 3. IN 7. OUT 4. GND 8. NC ORDERING INFORMATION PART NUMBER QUANTITY UPB1510GV-E1-A 1000/Reel Note: 1. Embossed tape 8 mm wide. Pin 1 is in the tape pull-out direction. Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. EXCLUSIVE NORTH AMERICAN AGENT FOR RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS CALIFORNIA EASTERN LABORATORIES • Headquarters • 4590 Patrick Henry Drive • Santa Clara, CA 95054-1817 • (408) 988-3500 • Telex 34-6393 • FAX (408) 988-0279 24-Hour Fax-On-Demand: 800-390-3232 (U.S. and Canada only) • Internet: http://WWW.CEL.COM DATA SUBJECT TO CHANGE WITHOUT NOTICE 09/13/2000 4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Concentration Limit per RoHS (values are not yet fixed) Concentration contained in CEL devices -A Not Detected Lead (Pb) < 1000 PPM Mercury < 1000 PPM Not Detected Cadmium < 100 PPM Not Detected Hexavalent Chromium < 1000 PPM Not Detected PBB < 1000 PPM Not Detected PBDE < 1000 PPM Not Detected -AZ (*) If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.