AGILENT MGA

3-volt, Low Noise Amplifier
for 0.8 – 6 GHz Applications
Technical Data
MGA-85563
Features
• 1.6 dB minimum Noise
Figure at 1.9 GHz
Surface Mount Package
SOT-363 (SC-70)
Description
Pin Connections and
Package Marking
The MGA-85563 features a
minimum noise figure of 1.6 dB
and associated gain of 18 dB at
1.9 GHz. The output is matched
internally to 50 Ω, and the input is
partially matched, requiring only
a single external inductor for
optimal performance. The supply
current can be adjusted using an
external resistor, varying IP3
from +12 dBm to +17 dBm.
• Adjustable IP3 from
+12 dBm to +17 dBm via
External Resistor
• 18 dB Gain at 1.9 GHz
• Single 3 V Supply
• Unconditionally Stable
Applications
GND
1
GND
2
INPUT
3
85x
• Amplifier for Cellular, PCS,
and Wireless LAN
Applications
6
OUTPUT
and Vd
5
GND
4
Rbias
Note:
Package marking provides orientation
and identification; “x” is date code.
Equivalent Circuit
(Simplified)
6
RF OUTPUT
and Vd
3
4
BIAS
RF
INPUT
R bias
1, 2, 5
BIAS
GROUND
Agilent’s MGA-85563 is
an easy-to-use GaAs RFIC
amplifier that offers low noise
figure and high gain from 0.8 to
6 GHz. Packaged in an ultraminiature SOT-363 package, it
requires half the board space of a
SOT-143 package.
The circuit uses state-of-the-art
PHEMT technology with proven
reliability. On-chip bias circuitry
allows operation from a single
+3 V supply, while resistive
feedback ensures stability (K > 1)
over frequency and temperature.
2
MGA-85563 Absolute Maximum Ratings
Symbol
Vd, max
Parameter
Units
Absolute
Maximum[1]
V
5.5
dBm
+13
Maximum Device Voltage
Pin
CW RF Input Power
Tch
Channel Temperature
°C
150
TSTG
Storage Temperature
°C
-65 to 150
Thermal Resistance[2]:
θ ch to c = 155°C/W
Notes:
1. Operation of this device above any one
of these limits may cause permanent
damage.
2. TC = 25°C (TC is defined to be the
temperature at the package pins where
contact is made to the circuit board).
Electrical Specifications, TC = 25°C, ZO = 50 Ω, Vd = 3 V, and using default of no external resistor at
the Rbias pin
Symbol
Units Min. Typ. Max. Std. Dev.[3]
Parameters and Test Conditions
Gain in Test Circuit [1]
f = 2.0 GHz
dB
NFtest
Noise Figure in Test Circuit [1]
f = 2.0 GHz
dB
1.85
NFMIN
Minimum Noise Figure
(measured with Γopt presented to the
input and 50 Ω presented to the output)
f = 0.9 GHz
f = 1.5 GHz
f = 2.0 GHz
f = 2.4 GHz
f = 4.0 GHz
f = 5.0 GHz
f = 6.0 GHz
dB
1.6
1.6
1.6
1.6
1.6
1.6
1.6
Associated Gain at NFMIN
(measured with Γopt presented to the
input and 50 Ω presented to the output)
f = 0.9 GHz
f = 1.5 GHz
f = 2.0 GHz
f = 2.4 GHz
f = 4.0 GHz
f = 5.0 GHz
f = 6.0 GHz
dB
Third Order Intercept Point
(measured with 50 Ω presented
to the input and output)
f = 0.9 GHz dBm
f = 1.5 GHz
f = 2.0 GHz
f = 2.4 GHz
f = 4.0 GHz
f = 5.0 GHz
f = 6.0 GHz
13
13
11.5
11.5
13
12.5
12
Output Power at 1 dB Gain Compression
(measured with 50 Ω presented
to the input and output)
f = 0.9 GHz dBm
f = 1.5 GHz
f = 2.0 GHz
f = 2.4 GHz
f = 4.0 GHz
f = 5.0 GHz
f = 6.0 GHz
0.8
0.9
0.9
1.0
1.4
1.3
1.2
Gtest
GA
IP3
P1 dB
16
19
17.0
17.5
18.0
18.5
17.5
16.0
14.5
1.0
2.3
0.1
0.1
1.0
1.2
1.1
3
MGA-85563 Electrical Specifications, continued, TC = 25°C, ZO = 50 Ω, Vd = 3 V, and using default
of no external resistor at the Rbias pin
Symbol
VSWR in
VSWR out
ISOL
Id
Parameters and Test Conditions
Units Min. Typ. Max. Std. Dev.[3]
Input VSWR [2]
Output
2.5:1
VSWR [2]
1.3:1
Isolation
f = 0.9 – 3.0 GHz
f = 3.0 – 6.0 GHz
Device Current
dB
37
30
mA
15
0.6
20
1.9
Notes:
1. Guaranteed specifications are 100% tested in the circuit of Figure 1.
2. Measured using the final test circuit shown below at f = 2 GHz.
3. Standard Deviation number is based on measurement of at least 500 parts from three non-consecutive wafer lots during
the initial characterization of this product, and is intended to be used as an estimate for distribution of the typical
specification.
MGA-85563 Final Test Circuit, TC = 25°C, ZO = 50 Ω
56 pF
RF
OUTPUT
85
RF
INPUT
18 nH
4.7 nH
56 pF
940 pF
3V
4
MGA-85563 Typical Performance, TC = 25°C, ZO = 50 Ω, Vd = 3 V, and using default of no external
resistor at the Rbias pin
20
ASSOCIATED GAIN (dB)
3
2
1
0
0
1
2
3
4
5
6
4
+85°C
+25°C
–40°C
18
16
14
12 3.3 V
3.0 V
2.7 V
10
0
1
Figure 1. Minimum Noise Figure vs.
Frequency and Voltage.
NOISE FIGURE AND GAIN (dB)
ASSOCIATED GAIN (dB)
16
14
3
4
5
5
6
0
14
12
GA50
NF50
NFMIN
10
8
6
4
2
1
2
3
4
5
6
2
3
4
5
6
FREQUENCY (GHz)
Figure 7. Output Power @ 1 dB Gain
Compression vs. Frequency and
Temperature.
6
4
2
0
-2 3.3V
3.0V
2.7V
-4
0
1
17
17
3.3V
3.0V
15 2.7V
15
13
13
11
2
3
4
5
6
+85°C
+25°C
–40°C
11
9
9
7
7
-2
-4
5
Figure 6. Output Power @ 1 dB Gain
Compression vs. Frequency and Voltage.
IP3 (dBm)
IP3 (dBm)
0
4
FREQUENCY (GHz)
Figure 5. Gain and Noise Figure (50 Ω
Source and Load) vs. Frequency.
2
3
Figure 3. Minimum Noise Figure vs.
Frequency and Temperature.
FREQUENCY (GHz)
+85°C
+25°C
–40°C
2
16
0
6
1
1
FREQUENCY (GHz)
0
6
Figure 4. Associated Gain vs.
Frequency and Temperature.
0
1
6
FREQUENCY (GHz)
OUTPUT POWER (dBm)
4
18
18
4
3
Figure 2. Associated Gain vs.
Frequency and Voltage.
20
2
2
FREQUENCY (GHz)
FREQUENCY (GHz)
12 +85°C
+25°C
–40°C
10
0
1
3
0
2
OUTPUT POWER (dBm)
NOISE FIGURE (dB)
3.3V
3.0V
2.7V
NOISE FIGURE (dB)
4
5
5
0
1
2
3
4
5
6
0
1
2
3
4
5
6
FREQUENCY (GHz)
FREQUENCY (GHz)
Figure 8. Output Third Order Intercept
Point vs. Frequency and Voltage.
Figure 9. Output Third Order Intercept
Point vs. Frequency and Temperature.
5
MGA-85563 Typical Performance, continued, TC = 25°C, ZO = 50 Ω, Vd = 3 V, and using default of
no external resistor at the Rbias pin
6
20
+85°C
+25°C
–40°C
16
12
8
4
IP3
12
8
0
1
2
3
4
5
P1dB
0
14 16 18
6
2
0
-2
-4
-6
4
0
INPUT, IP3 (dBm)
16
31 mA
23 mA
19 mA
15 mA
4
P1dB and IP3 (dBm)
DEVICE CURRENT, Id (mA)
20
-8
-10
20 22 24 26 28 30
32
0
1
2
3
4
5
6
SUPPLY VOLTAGE (V)
CURRENT (mA) @ 2.0 GHz
FREQUENCY (GHz)
Figure 10. Device Current vs. Voltage
and Temperature.
Figure 11. Output Third Order
Intercept and P1dB vs. Device Current.
Figure 12. Input Third Order Intercept
vs. Frequency and Device Current.
10
25
8
23
GAIN (dB)
VSWR
Input
6
4
Output
2
1
2
3
4
5
6
FREQUENCY (GHz)
Figure 13. Input and Output VSWR vs.
Frequency.
Gass
19
17
0
0
21
Gain, |S21|2
15
14 16 18
20 22 24 26 28 30
32
CURRENT (mA) @ 2.0 GHz
Figure 14. Gain, |S21|2, and Gain
Associated with Minimum Noise vs.
Current.
6
MGA-85563 Typical Scattering Parameters, TC = 25°C, ZO = 50 Ω, Vd = 3 V, and using default of
no external resistor at the Rbias pin
Freq.
S11
GHz
dB Mag. Ang.
dB
0.2
0.5
0.9
1.0
1.5
1.8
1.9
2.0
2.1
2.2
2.3
2.4
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
-1.1
-1.7
-2.1
-2.2
-2.2
-2.3
-2.3
-2.3
-2.2
-2.2
-2.2
-2.2
-2.3
-2.6
-3.4
-5.4
-5.3
-5.9
-6.8
-8.2
-9.4
-10.8
-12.3
-13.5
0.88
0.82
0.79
0.78
0.77
0.76
0.77
0.77
0.77
0.78
0.78
0.77
0.77
0.75
0.68
0.54
0.55
0.51
0.46
0.39
0.34
0.29
0.24
0.21
-10
-15
-22
-24
-34
-39
-41
-43
-45
-48
-50
-53
-55
-68
-84
-90
-96
-110
-123
-136
-150
-164
-174
172
S21
Mag.
Ang.
dB
1.6
3.8
5.5
5.7
6.6
6.7
6.7
6.8
6.9
7.0
7.0
7.2
7.3
7.6
7.7
6.5
6.1
5.9
5.6
5.3
4.9
4.5
4.0
3.7
115
66
27
20
-11
-26
-30
-34
-38
-42
-47
-51
-55
-78
-102
-126
-139
-156
-173
169
152
136
120
106
-30.8
-33.6
-35.9
-36.5
-39.2
-41.1
-41.3
-41.0
-40.3
-39.2
-39.2
-39.2
-38.4
-35.9
-31.7
-28.9
-30.2
-29.9
-29.6
-28.9
-28.0
-27.1
-26.2
-25.7
4.0
11.5
14.8
15.2
16.4
16.5
16.6
16.6
16.8
16.9
17.1
17.2
17.3
17.6
17.8
16.3
15.7
15.4
15.0
14.4
13.8
13.0
12.1
11.3
S12
Mag. Ang.
0.029
0.021
0.016
0.015
0.011
0.009
0.009
0.009
0.010
0.011
0.011
0.011
0.012
0.016
0.026
0.036
0.031
0.032
0.033
0.036
0.040
0.044
0.049
0.052
MGA-85563 Typical Noise Parameters,
TC = 25°C, ZO = 50 Ω, Vd = 3 V, and using default of no external resistor
at the Rbias pin
Γopt
Frequency
(GHz)
Fmin
(dB)
Mag.
Ang.
RN
(Ω)
0.2
0.5
0.9
1.0
1.5
1.8
1.9
2.0
2.1
2.2
2.3
2.4
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
1.63
1.61
1.60
1.59
1.57
1.56
1.56
1.56
1.56
1.56
1.56
1.56
1.56
1.57
1.56
1.57
1.58
1.59
1.59
1.63
1.65
1.66
1.68
1.70
0.70
0.67
0.63
0.62
0.57
0.56
0.56
0.56
0.56
0.55
0.54
0.54
0.53
0.50
0.49
0.49
0.46
0.43
0.40
0.35
0.25
0.15
0.06
0.04
28
29
29
29
30
32
33
34
35
37
39
41
42
49
54
61
69
78
86
94
104
114
125
-48
0.86
0.81
0.73
0.72
0.63
0.59
0.59
0.58
0.57
0.55
0.53
0.52
0.51
0.47
0.43
0.41
0.37
0.32
0.29
0.25
0.23
0.20
0.18
0.15
1
-18
-16
-15
-8
5
16
26
31
34
37
39
42
57
61
38
27
29
26
25
23
19
14
8
dB
S22
Mag.
Ang.
K
Factor
-4.5
-9.8
-15.3
-16.2
-19.3
-19.5
-19.7
-20.5
-22.0
-24.2
-25.8
-27.1
-28.2
-22.4
-15.0
-10.2
-11.1
-11.1
-11.1
-10.8
-10.5
-10.1
-9.8
-9.4
0.60
0.32
0.17
0.16
0.11
0.11
0.10
0.09
0.08
0.06
0.05
0.04
0.04
0.08
0.18
0.31
0.28
0.28
0.28
0.29
0.30
0.31
0.33
0.34
-42
-69
-79
-78
-81
-88
-97
-110
-123
-136
-149
-164
176
113
92
51
26
15
4
-7
-17
-26
-35
-45
2.1
2.1
2.3
2.3
2.7
3.5
3.6
3.4
3.1
2.8
2.6
2.5
2.4
1.8
1.3
1.4
1.7
1.8
1.9
2.0
2.1
2.1
2.2
2.2
7
Description
The MGA-85563 is a two-stage,
low noise GaAs RFIC amplifier
designed for receiver applications
in the 800 MHz to 5.8 GHz
frequency range. The device
combines low noise performance
with high linearity to make it a
desirable choice for receiver front
end stages.
A special feature of the
MGA-85563 is the ability to
customize its output power
capability for higher linearity by
setting the device’s current. For
applications requiring additional
dynamic range, the third order
intercept point can be boosted by
up to 6 dB by using this feature.
The MGA-85563 operates from a
+3-volt power supply and draws a
nominal current of 15 mA. The
RFIC is contained in a miniature
SOT-363 (SC-70) package to
minimize printed circuit board
space. The combination of 3-volt
operation and small size are
important to designers of miniature, battery-powered wireless
communications products such as
cellular telephones, PCS, and RF
modems.
The high frequency response of
the MGA-85563 extends through
6 GHz making it an excellent
choice for use in 5 GHz RLL as
well as 2.4 and 5.7 GHz spread
spectrum and ISM/license-free
band applications.
Internal, on-chip capacitors limit
the low end frequency response
to applications above approximately 500 MHz.
Application Guidelines
The MGA-85563 is very easy to
use. For most applications, all
that is required to operate the
MGA-85563 is to apply +3 volts to
the RF Output pin, and noise
match the RF Input.
RF Input
To achieve lowest noise figure
performance, the input of the
MGA-85563 should be matched
from the system impedance
(typically 50 Ω) to the optimum
source impedance for minimum
noise, Γopt. Since the real part of
the input of the device impedance
is near 50 Ω and the reactive part
is capacitive, a simple series
inductor at the input is often all
that is needed to provide a
suitable noise match for many
applications.
RF Output
The RF Output port is internally
matched to 50 Ω and will not
normally require additional
matching.
DC Bias
DC bias is applied to the
MGA-85563 through the RF
Output connection. Figure 15
shows how an inductor (RFC) is
used to isolate the RF signal from
the DC supply. The bias line is
capacitively bypassed to keep RF
from the DC supply lines and
prevent resonant dips or peaks in
the response of the amplifier.
The DC schematic for an
MGA-85563 amplifier circuit is
shown in Figure 15.
C3
RF
Input
C1
Rb
85
MGA-85563 Applications
Information
+3V
RFC
RF
Output
C2
Figure 15. Schematic Diagram with
Bias and Current Setting
Connections.
A DC blocking capacitor (C2) is
used at the output of the RFIC to
isolate the supply voltage from
succeeding circuits.
While the RF input terminal of the
MGA-85563 is at DC ground
potential, it should not be used as
a current sink. If the input is
connected directly to a preceding
stage that has a DC voltage
present, a blocking capacitor (C1)
should be used.
Setting the Bias Current for
Higher Linearity
The MGA-85563 has a feature that
allows the user to place an
external resistor (Rb) from the
R bias pin to DC ground and
thereby increase the device
current. The current can be raised
from its nominal 15 mA up to
approximately 50 mA. The higher
current increases amplifier
linearity by boosting output
power (P1dB) by up to 8 dB.
Maximum linearity performance
is obtained at a current of 30 to
35 mA. Currents greater than
35 mA are not recommended
since the output power has
reached a point of diminishing
returns at this current.
Figure 16 shows the relationship
between device current and the
value of the external resistor.
8
that could impair the high frequency RF performance of the
MGA-85563. The layout is shown
with a footprint of a SOT-363
package superimposed on the
PCB pads for reference.
35
25
20
15
10
10
50
90
130
170
200
Rb (Ω)
Figure 16. Bias Current vs. Resistor
Value.
The current is increased only in
the second stage of the
MGA-85563. Bias current for the
first stage remains fixed and thus
the input impedance and noise
figure for the amplifier are
unaffected by the increase in bias
current. The output match is also
generally unaffected by increased
device current and remains quite
good over the complete operating
current and frequency range.
PCB Layout
A recommended PCB pad layout
for the miniature SOT-363 (SC-70)
package that is used by the
MGA-85563 is shown in Figure 17.
0.026
Starting with the package pad
layout in Figure 17, an RF layout
similar to the one shown in
Figure 18 a good starting point for
microstripline designs using the
MGA-85563 amplifier.
RF
Input
85
Id (mA)
30
RF
Output
Rb
Figure 18. RF Layout.
Adequate grounding of Pins 1, 2,
and 5 of the RFIC are important
to maintain device stability and
RF performance. Each of the
ground pins should be connected
to the groundplane on the backside of the PCB by means of
plated through holes (vias). The
ground vias should be placed as
close to the package terminals as
practical. At least one via should
be located next to each ground
pin to assure good RF grounding.
It is a good practice to use
multiple vias to further minimize
ground path inductance.
0.075
0.035
0.016
Figure 17. PCB Pad Layout for
MGA-85563 Package (dimensions in
inches).
This layout provides ample
allowance for package placement
by automated assembly equipment without adding parasitics
If the adjustable current feature is
to be used, an additional ground
pad located near the Rbias pin may
be used to connect the currentsetting resistor (Rb) directly from
the Rbias pin to ground. (The
ground pad for Pin 5 could also
be used for this purpose.) Note
that when using an external
resistor, the Rbias pad should not
be bypassed to ground. Doing so
could result in undesirable
resonances in the amplifier gain
response.
If for any reason the R b resistor is
not located immediately adjacent
to the MGA-85563 (such as in the
case of remote current adjustment or to implement dynamic
control of the device’s linearity),
then a small series resistor (e.g.,
10 Ω) should be located near the
Rbias pin to de-Q the connection
from the MGA-85563 to the
external current-setting circuit.
If the adjustable current feature
of the MGA-85563 is not used, the
Rbias pin should be left open.
When not used, the PCB pad for
the R bias pin should only be large
enough to provide a mechanical
attachment, such as shown in
Figure 17. If a large pad or length
of line is connected to the R bias
pad, a potential exists for the pad
parasitics to interact with the
internal circuitry of the
MGA-85563 to create an undesirable resonance in the gain
response of the amplifier.
While it might be considered an
effective RF practice, it is recommended that the PCB pads for the
ground pins not be connected
together underneath the body of
the package. In many cases, it is
important that the individual
stages within the device be
grounded separately to prevent
inadvertent interstage feedback.
In addition, PCB traces hidden
under the package cannot be
adequately inspected for SMT
solder bridging or quality.
PCB Materials
FR-4 or G-10 type materials are
good choices for most low cost
wireless applications using single
or multi-layer printed circuit
boards. Typical single-layer board
thickness is 0.020 to 0.031 inches.
Circuit boards thicker than
0.031 inches are not recom-
9
For noise figure critical or higher
frequency applications, the
additional cost of PTFE/glass
dielectric materials may be
warranted to minimize transmission line loss at the amplifier’s
input.
Application Example
The printed circuit layout in
Figure 19 can be used with the
MGA-85563 for frequencies from
800 MHz through 6 GHz. This
layout is a microstripline design
(solid groundplane on the backside of the circuit board) with
50 Ω interfaces for the RF input
and output. The circuit is fabricated on 0.031-inch thick FR-4
dielectric material. Plated
through holes (vias) are used to
bring the ground to the top side
of the circuit where needed.
Multiple vias are used to reduce
the inductance of the paths to
ground.
matched to Γopt . From the table
of Typical Noise Parameters, the
value of Γopt at 1.9 GHz is found
to be 0.56 ∠+33°. The conjugate
of Γopt , 0.56 ∠-33°, is plotted on
the Smith chart as Point A in
Figure 20. The addition of a
0.108 inch length (actual length
on FR-4; electrical length is 11.7°
of 50 Ω transmission line (MLIN)
rotates Point A around to the
R = 1 circle on the Smith chart. A
series 5.6 nH inductor (L1) is then
all that is required to complete
the match to 50 Ω.
1
0.5
2
C (50 Ω)
0.2
RF
Input
0.2
B
L1
A (Γopt)
MLIN
2
0.5
C1
Vd
L1 MLIN
C3
RF
Input
85
mended due to excessive
inductance in the ground vias.
Rb
C4
RFC
C2
RF
Output
Notes: L1 = 5.6 nH
RFC = 22 nH
C1 – C4 = 56 pH
MLIN = 0.108 inch, 50 Ω
(C1, C4 and Rb are optional)
Figure 22. Schematic of 1.9 GHz
Circuit.
DC bias is applied to the
MGA-85563 through the RFC at
the RF Output pin. The power
supply connection is bypassed to
ground with capacitor C3. Provision is made for an additional
bypass capacitor, C4, to be added
to the bias line near the +3 volt
connection. C4 will not normally
be needed unless several stages
are cascaded using a common
power supply.
C
A
-0.2
B
-2
-0.5
-1
The optional resistor, Rb, may be
added if desired to increase
device current to handle higher
level signals. The use of the biassetting resistor will not affect the
input matching circuit.
Figure 20. Input Impedance Match.
+Vd
The output of the MGA-85563 is
already well matched to 50 Ω and
no additional matching is needed.
IN
The resulting RF circuit is shown
in Figure 21.
Rbias
OUT
MGA-85-A
5.6 nH
RF
Input
50 Ω
0.108 in.
MGARF
85563 Output
Figure 21. Input Circuit for 1.9 GHz.
Figure 19. Multi-purpose PCB Layout.
1.9 GHz Design
To illustrate the simplicity of
using the MGA-85563, a 1.9 GHz
amplifier for PCS type receiver
applications is presented.
To achieve minimum noise figure,
the 50 Ω input to the amplifier is
Since the input terminal of the
MGA-85563 is at ground potential,
the input DC blocking capacitor
C1 need not be used unless the
amplifier is connected to a
preceding stage that has a voltage
present at this point.
A schematic diagram of the
complete 1.9 GHz circuit with the
input noise match and DC biasing
is shown in Figure 22.
The value of the DC blocking and
RF bypass capacitors (C1 – C4)
should be chosen to provide a
small reactance (typically
<2 ohms) at the lowest operating
frequency. For this 1.9 GHz
design example, 56 pF capacitors
with a reactance of 1.5 ohms are
adequate. The reactance of the
RF choke (RFC) should be high
(i.e., several hundred ohms) at
10
+Vd
IN
Actual component values may
differ slightly from those shown
in Table 1 due to variations in
circuit layout, grounding, and
component parasitics. A CAD
program such as Agilent’s Touchstone® is recommended to fully
analyze and account for these
circuit variables.
C4
MLIN
85
L1
C3
RFC
C2
Rbias
Hints and Troubleshooting
OUT
MGA-85-A
Figure 23. Complete 1.9 GHz Amplifier Circuit.
the lowest frequency of operation. A 22 nH inductor with a
reactance of 262 ohms at 1.9 GHz
is sufficiently high to minimize
the loss from circuit loading.
The completed 1.9 GHz amplifier
for this example with all components and SMA connectors
assembled is shown in Figure 23.
Designs for Other
Frequencies
The same basic design approach
described above for 1.9 GHz can
be applied to other frequency
bands. Inductor values for
matching the input for low noise
figure are shown in Table 1.
For frequencies below 1000 MHz,
the series input inductor
approach provides a good match
but may not completely noise
match the MGA-85563. A twoelement matching circuit may be
required at lower frequencies to
exactly match the input to Γopt. At
lower frequencies, the real part of
Γopt has started to move away
from 50 Ω (i.e., away from the
R = 1 circle on the Smith chart) as
the angle of Γopt decreases. A
small shunt capacitor (typically
0.4 to 0.9 pF) added between the
input pin and the adjacent ground
pad to create a shunt C-series L
matching network will realize an
improvement in noise figure of
several tenths of a dB. A lower
value for L1 may be needed
depending on the actual length of
the input line between Pin 1 and
L1 as well as the value of the
shunt C.
For frequencies above 3 GHz, the
input is already well matched to
50 Ω and no additional matching
is normally needed.
Frequency
(GHz)
0.8*
0.9*
1.5
1.9
2.4
5.1
5.8
L1
(nH)
22
18
8.2
5.6
2.7
0
0
Table 1. Input Inductor Values for
Various Operating Frequencies.
(*Additional matching required for
optimum NF).
Oscillation
Unconditional stability of the
MGA-85563 is dependent on
having very good grounding.
Inadequate device grounding or
poor PCB layout techniques could
cause the device to be potentially
unstable.
Even though a design may be
unconditionally stable (K > 1 and
B1 > 0) over its full frequency
range, other possibilities exist
that may cause an amplifier
circuit to oscillate. One thing to
check is feedback in bias circuits.
It is important to capacitively
bypass the connections to active
bias circuits to ensure stable
operation. In multistage circuits,
feedback through bias lines can
also lead to oscillation.
Components of insufficient
quality for the frequency range of
the amplifier can sometimes lead
to instability. Also, component
values that are chosen to be much
higher in value than is appropriate for the application can
present a problem. In both of
these cases, the components may
have reactive parasitics that make
their impedances very different
than expected. Chip capacitors
may have excessive inductance,
or chip inductors can exhibit
resonances at unexpected
frequencies.
11
A Note on Supply Line
Bypassing
Multiple bypass capacitors are
normally used throughout the
power distribution within a
wireless system. Consideration
should be given to potential
resonances formed by the combination of these capacitors and the
inductance of the DC distribution
lines. The addition of a small
value resistor in the bias supply
line between bypass capacitors
will often de-Q the bias circuit
and eliminate resonance effects.
Statistical Parameters
Several categories of parameters
appear within this data sheet.
Parameters may be described
with values that are either
“minimum or maximum,”
“typical,” or “standard
deviations.”
The values for parameters are
based on comprehensive product
characterization data, in which
automated measurements are
made on of a minimum of 500
parts taken from three nonconsecutive process lots of
semiconductor wafers. The data
derived from product characterization tends to be normally
distributed, e.g., fits the standard
bell curve.
Parameters considered to be the
most important to system performance are bounded by minimum
or maximum values. For the
MGA-85563, these parameters
are: Gain (Gtest), Noise Figure
(NFtest), and Device Current (Id).
Each of the guaranteed parameters is 100% tested as part of the
manufacturing process.
typical data are the mathematical
mean (µ), of the normal distribution taken from the characterization data. For parameters where
measurements or mathematical
averaging may not be practical,
such as S-parameters or Noise
Parameters and the performance
curves, the data represents a
nominal part taken from the
center of the characterization
distribution. Typical values are
intended to be used as a basis for
electrical design.
To assist designers in optimizing
not only the immediate amplifier
circuit using the MGA-85563, but
to also evaluate and optimize
trade-offs that affect a complete
wireless system, the standard
deviation (σ) is provided for
many of the Electrical Specifications parameters (at 25°C) in
addition to the mean. The standard deviation is a measure of the
variability about the mean. It will
be recalled that a normal distribution is completely described by
the mean and standard deviation.
Standard statistics tables or
calculations provide the probability of a parameter falling between
any two values, usually symmetrically located about the mean.
Referring to Figure 24 for example, the probability of a
parameter being between ±1σ is
68.3%; between ±2σ is 95.4%; and
between ±3σ is 99.7%.
68%
95%
99%
-3σ
Values for most of the parameters
in the table of Electrical Specifications that are described by
-2σ
-1σ Mean (µ) +1σ +2σ
(typical)
+3σ
Parameter Value
Figure 24. Normal Distribution.
Phase Reference Planes
The positions of the reference
planes used to specify S-parameters and Noise Parameters for
the MGA-85563 are shown in
Figure 25. As seen in the illustration, the reference planes are
located at the point where the
package leads contact the test
circuit.
REFERENCE
PLANES
TEST CIRCUIT
Figure 25. Phase Reference Planes.
SMT Assembly
Reliable assembly of surface
mount components is a complex
process that involves many
material, process, and equipment
factors, including: method of
heating (e.g., IR or vapor phase
reflow, wave soldering, etc.)
circuit board material, conductor
thickness and pattern, type of
solder alloy, and the thermal
conductivity and thermal mass of
components. Components with a
low mass, such as the SOT-363
package, will reach solder reflow
temperatures faster than those
with a greater mass.
The MGA-85563 is qualified to the
time-temperature profile shown
in Figure 26. This profile is
representative of an IR reflow
type of surface mount assembly
process.
After ramping up from room
temperature, the circuit board
with components attached to it
(held in place with solder paste)
passes through one or more
preheat zones. The preheat zones
increase the temperature of the
board and components to prevent
thermal shock and begin evapo-
12
250
TMAX
TEMPERATURE (°C)
200
150
Reflow
Zone
100
Preheat
Zone
Cool Down
Zone
50
0
0
60
120
180
240
300
TIME (seconds)
Figure 26. Surface Mount Assembly Profile.
rating solvents from the solder
paste. The reflow zone briefly
elevates the temperature sufficiently to produce a reflow of the
solder.
only to the minimum temperatures and times necessary to
achieve a uniform reflow of
solder.
Electrostatic Sensitivity
The rates of change of temperature for the ramp-up and cooldown zones are chosen to be low
enough to not cause deformation
of the board or damage to components due to thermal shock. The
maximum temperature in the
reflow zone (TMAX) should not
exceed 235°C.
These parameters are typical for a
surface mount assembly process
for the MGA-85563. As a general
guideline, the circuit board and
components should be exposed
RFICs are electrostatic discharge
(ESD) sensitive
devices. Although the
MGA-85563 is robust in design,
permanent damage may occur to
these devices if they are subjected to high energy electrostatic
discharges. Electrostatic charges
as high as several thousand volts
(which readily accumulate on the
human body and on test equipment) can discharge without
detection and may result in
degradation in performance,
reliability, or failure.
Electronic devices may be
subjected to ESD damage in any
of the following areas:
•
•
•
•
Storage & handling
Inspection & testing
Assembly
In-circuit use
The MGA-85563 is a ESD Class 1
device. Therefore, proper ESD
precautions are recommended
when handling, inspecting,
testing, assembling, and using
these devices to avoid damage.
13
Package Dimensions
Outline 63 (SOT-363/SC-70)
PACKAGE
MARKING
CODE (XX)
1.30 (0.051)
REF.
2.20 (0.087)
2.00 (0.079)
XXX
DATE CODE (X)
1.35 (0.053)
1.15 (0.045)
0.650 BSC (0.025)
0.425 (0.017)
TYP.
2.20 (0.087)
1.80 (0.071)
0.10 (0.004)
0.00 (0.00)
0.30 REF.
1.00 (0.039)
0.80 (0.031)
0.25 (0.010)
0.15 (0.006)
10°
0.30 (0.012)
0.10 (0.004)
0.20 (0.008)
0.10 (0.004)
DIMENSIONS ARE IN MILLIMETERS (INCHES)
MGA-85563 Part Number Ordering Information
Part Number
Devices per Container
Container
MGA-85563-TR1
3000
7" reel
MGA-85563-BLK
100
Antistatic bag
14
Device Orientation
REEL
END VIEW
TOP VIEW
4 mm
8 mm
CARRIER
TAPE
85x
85x
85x
85x
USER
FEED
DIRECTION
COVER TAPE
Tape Dimensions and Product Orientation
For Outline 63
P
P2
D
P0
E
F
W
C
D1
t1 (CARRIER TAPE THICKNESS)
Tt (COVER TAPE THICKNESS)
K0
8° MAX.
A0
DESCRIPTION
5° MAX.
B0
SYMBOL
SIZE (mm)
SIZE (INCHES)
CAVITY
LENGTH
WIDTH
DEPTH
PITCH
BOTTOM HOLE DIAMETER
A0
B0
K0
P
D1
2.24 ± 0.10
2.34 ± 0.10
1.22 ± 0.10
4.00 ± 0.10
1.00 + 0.25
0.088 ± 0.004
0.092 ± 0.004
0.048 ± 0.004
0.157 ± 0.004
0.039 + 0.010
PERFORATION
DIAMETER
PITCH
POSITION
D
P0
E
1.55 ± 0.05
4.00 ± 0.10
1.75 ± 0.10
0.061 ± 0.002
0.157 ± 0.004
0.069 ± 0.004
CARRIER TAPE
WIDTH
THICKNESS
W
t1
8.00 ± 0.30
0.255 ± 0.013
0.315 ± 0.012
0.010 ± 0.0005
COVER TAPE
WIDTH
TAPE THICKNESS
C
Tt
5.4 ± 0.10
0.062 ± 0.001
0.205 ± 0.004
0.0025 ± 0.00004
DISTANCE
CAVITY TO PERFORATION
(WIDTH DIRECTION)
F
3.50 ± 0.05
0.138 ± 0.002
CAVITY TO PERFORATION
(LENGTH DIRECTION)
P2
2.00 ± 0.05
0.079 ± 0.002
www.semiconductor.agilent.com
Data subject to change.
Copyright © 1999 Agilent Technologies
Obsoletes 5966-4894E
5968-6303E (11/99)