HOLTEK HT82A821R

HT82A821R
USB Audio MCU
Features
· USB 2.0 full speed compatible
· Total FIFO size are 400 byte (8, 8, 384 for EP0~EP2)
· USB spec v1.1 full speed operation and USB audio
· 2048´15 program memory ROM
device class spec v1.0
· 192´8 MCU type data memory RAM (Bank0)
· Operating voltage: fSYS= 6MHz/12MHz: 3.3V~5.5V
· HALT function and wake-up feature reduce power
· Low voltage reset function (3.0V±0.3V)
consumption
· High-performance 48kHz sampling rate for audio
· 8 bidirectional I/O lines (max.)
playback
· Two 16-bit programmable timer/event counter and
· Embedded class AB power amplifier for speaker
overflow interrupts
driving
· Watchdog Timer
· Embedded High Performance 16 bit audio DAC
· 16-level subroutine nesting
· Support digital volume control
· Bit manipulation instruction
· HID support which can remote control of playback
· 15-bit table read instruction
volume/mute
· 63 powerful instructions
· 3 endpoints supported (endpoint 0 included)
· All instructions in one or two machine cycles
· Support 1 Control , 1 Interrupt , 1 Isochronous
· 24-pin SSOP (150mil), 24-pin SOP (300mil) package
transfer
General Description
tal programmable gain amplifier. The gain range is from
-32dB to +6dB.
This HT82A821R is an 8-bit high performance
RISC-like microcontroller designed for USB Speaker
product applications. The HT82A821R combines a
16-bit DAC, USB transceiver, SIE (Serial Interface Engine), audio class processing unit, FIFO, 8-bit MCU into
a single chip. The DAC in the HT82A821R is operating
at the 48kHz sampling rate. The HT82A821R has a digi-
Rev. 1.10
The HT82A821R has a Human Interface Device function that allows a user to control the playback volume at
the device side. The HT82A821R also can mute the analog output signal by the operation of HID buttons.
1
June 29, 2007
HT82A821R
Block Diagram
S T A C K 0
B P
S T A C K 1
S T A C K 2
T M R 1 C
In te rru p t
C ir c u it
P ro g ra m
C o u n te r
S T A C K 1 5
M
T M R 0 C
M
M P
U
fS
Y S
/4
fS
Y S
/4
X
IN T C
T M R 0
In s tr u c tio n
R e g is te r
U
T M R 1
S T A C K 1 4
P ro g ra m
R O M
M
U
X
D A T A
M e m o ry
X
E N /D IS
W D T S
W D T P r e s c a le r
P A C
O S C I
U S B D +
U S B D V 3 3 O
P O R T A
P A
S T A T U S
A L U
O S C O
M
U
fS
X
Y S
/4
W D T O S C
M U X
In s tr u c tio n
D e c o d e r
T im in g
G e n e ra to r
W D T
P A 0 ~ P A 7
S h ifte r
A C C
U S B 1 .1 X C V R
U S B 1 .1
F u ll S p e e d E n g in e
3 .3 V R e g u la to r
F IF O
IS O
P ro c e s s
D ig ita l
V o lu m e
C o n tro l
D A C
W r ite D a ta
M U X
1 6 - b it
D /A
L O U T
P o w e r
A m p
R O U T
Pin Assignment
P A 3
1
2 4
P A 4
P A 2
2
2 3
P A 5
P A 1
3
2 2
P A 6
P A 0
4
2 1
P A 7
A V D D 2
5
2 0
D V S S 1
R O U T
6
1 9
V 3 3 O
L O U T
7
1 8
U S B D P
A V S S 2
8
1 7
U S B D N
A V S S 1
9
1 6
D V D D 1
B IA S
1 0
1 5
R E S E T
A V D D 1
1 1
1 4
O S C O
D V S S 2
1 2
1 3
O S C I
H T 8 2 A 8 2 1 R
2 4 S S O P -A /S O P -A
Rev. 1.10
2
June 29, 2007
HT82A821R
Pin Description
Pin No. Pin Name
I/O
Description
4~1,
24~21
PA0~PA7
I/O
Bidirectional 8-bit input/output port. Each bit can be configured as wake-up input by
mask option. Software instructions determine the CMOS output or Schmitt trigger input
with or without pull-high (by mask option).
5
AVDD2
¾
Audio power amplifier positive power supply.
6
ROUT
O
Right driver analog output
7
LOUT
O
Left driver analog output
8
AVSS2
¾
Audio power amplifier negative power supply, ground
9
AVSS1
¾
Audio DAC negative power supply, ground
10
BIAS
O
Connect a capacitor to ground to increase half-supply stability
11
AVDD1
¾
Audio DAC positive power supply
12
DVSS2
¾
Negative digital & I/O power supply, ground
13
14
OSCI
OSCO
I
O
OSCI, OSCO are connected to an 6MHz or 12MHz crystal/resonator (determined by
software instructions) for the internal system clock
15
RESET
I
Schmitt trigger reset input, active low
16
DVDD1
¾
Positive digital power supply
17
USBDN
I/O
USBDN is USBD- line
USB function is controlled by software control register
18
USBDP
I/O
USBDP is USBD+ line
USB function is controlled by software control register
19
V33O
O
3.3V regulator output
20
DVSS1
¾
Negative digital power supply, ground
Absolute Maximum Ratings
Supply Voltage ...........................VSS-0.3V to VSS+6.0V
Storage Temperature ............................-50°C to 125°C
Input Voltage..............................VSS-0.3V to VDD+0.3V
Operating Temperature...........................-40°C to 85°C
IOL Total ..............................................................150mA
IOH Total............................................................-100mA
Total Power Dissipation .....................................500mW
Note: These are stress ratings only. Stresses exceeding the range specified under ²Absolute Maximum Ratings² may
cause substantial damage to the device. Functional operation of this device at other conditions beyond those
listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability.
Rev. 1.10
3
June 29, 2007
HT82A821R
D.C. Characteristics
Symbol
Parameter
Ta=25°C
Test Conditions
VDD
Conditions
¾
Min.
Typ.
Max.
Unit
3.3
5
5.5
V
VDD
Operating Voltage
5V
IDD
Operating Current
5V
No load, fSYS=12MHz
¾
9
¾
mA
ISTB1
Standby Current
5V
No load, system HALT,
USB suspend
¾
3
¾
mA
ISTB2
Standby Current
5V
No load, system HALT,
USB transceiver and 3.3V
regulator on
¾
146
¾
mA
VIL1
Input Low Voltage for I/O Ports
5V
¾
0
¾
0.3VDD
V
VIH1
Input High Voltage for I/O Ports
5V
¾
0.7VDD
¾
VDD
V
VIL2
Input Low Voltage (RESET)
5V
¾
0
¾
0.4VDD
V
VIH2
Input High Voltage (RESET)
5V
¾
0.9VDD
¾
VDD
V
IOL
I/O Port Sink Current
5V
VOL=0.1VDD
¾
5
¾
mA
IOH
I/O Port Source Current
5V
VOH=0.7VDD
¾
-5
¾
mA
RPH
Pull-high Resistance
5V
¾
30
50
90
kW
VLVR
Low Voltage Reset
5V
¾
2.7
3
3.3
V
VV33O
3.3V Regulator Output
5V
3
3.3
3.6
V
IV33O=-5mA
DAC+Power Amp:
Test condition: Measurement bandwidth 20Hz to 20kHz, fS= 48kHz. Line output series capacitor with 220mF.
THD+N
SNR
DR
POUT
THD+NNote1
Signal to Noise RatioNote1
Dynamic Range
Output Power
4W load
¾
-30
¾
8W load
¾
-35
¾
4W load
¾
81
¾
8W load
¾
82
¾
4W load
¾
87
¾
8W load
¾
88
¾
4W load, THD=10%
¾
400
¾
8W load, THD=10%
¾
200
¾
5V
5V
5V
5V
dB
dB
dB
mW/ch
Note: 1. Sine wave input at 1kHz, -6dB
A.C. Characteristics
Symbol
Parameter
Ta=25°C
Test Conditions
Min.
Typ.
Max.
Unit
¾
0.4
¾
12
MHz
5V
¾
¾
100
¾
ms
RESET Input Pulse Width
¾
¾
1
¾
¾
ms
tSST
System Start-up Timer Period
¾
¾
¾
1024
¾
tSYS
tINT
Interrupt Pulse Width
¾
¾
1
¾
¾
ms
VDD
Conditions
5V
tWDTOSC Watchdog Oscillator Period
tRES
fSYS
System Clock (Crystal OSC)
Note: tSYS=1/fSYS
Rev. 1.10
4
June 29, 2007
HT82A821R
Functional Description
incremented by one. The program counter then points to
the memory word containing the next instruction code.
Execution Flow
The system clock for the micro-controller is from a crystal oscillator. The system clock is internally divided into
four non-overlapping clocks. One instruction cycle consists of four system clock cycles.
When executing a jump instruction, conditional skip execution, loading to the PCL register, performing a subroutine call or return from subroutine, initial reset,
internal interrupt, external interrupt or return from interrupts, the PC manipulates the program transfer by loading the address corresponding to each instruction.
Instruction fetching and execution are pipelined in such
a way that a fetch takes an instruction cycle while decoding and execution takes the next instruction cycle.
However, the pipelining scheme causes each instruction to be effectively executed in a cycle. If an instruction
changes the program counter, two cycles are required to
complete the instruction.
The conditional skip is activated by instructions. Once
the condition is met, the next instruction, fetched during
the current instruction execution, is discarded and a
dummy cycle replaces it to get the proper instruction.
Otherwise proceed with the next instruction.
Program Counter - PC
The lower byte of the program counter (PCL) is a readable and writeable register (06H). Moving data into the
PCL performs a short jump. The destination will be
within the current program ROM page.
The program counter (PC) controls the sequence in
which the instructions stored in the program ROM are
executed and its contents specify a full range of program memory.
When a control transfer takes place, an additional
dummy cycle is required.
After accessing a program memory word to fetch an instruction code, the contents of the program counter are
S y s te m
C lo c k
T 1
T 2
T 3
T 4
T 1
T 2
T 3
T 4
T 1
T 2
T 3
T 4
O S C 2 ( R C o n ly )
P C
P C
P C + 1
F e tc h IN S T (P C )
E x e c u te IN S T (P C -1 )
P C + 2
F e tc h IN S T (P C + 1 )
E x e c u te IN S T (P C )
F e tc h IN S T (P C + 2 )
E x e c u te IN S T (P C + 1 )
Execution Flow
Mode
Program Counter
*10
*9
*8
*7
*6
*5
*4
*3
*2
*1
*0
Initial Reset
0
0
0
0
0
0
0
0
0
0
0
USB Interrupt
0
0
0
0
0
0
0
0
1
0
0
Timer/Event Counter 0 Overflow
0
0
0
0
0
0
0
1
0
0
0
Timer/Event Counter 1 Overflow
0
0
0
0
0
0
0
1
1
0
0
Skip
Program Counter+2
Loading PCL
*10
*9
*8
@7
@6
@5
@4
@3
@2
@1
@0
Jump, Call Branch
#10
#9
#8
#7
#6
#5
#4
#3
#2
#1
#0
Return from Subroutine
S10
S9
S8
S7
S6
S5
S4
S3
S2
S1
S0
Program Counter
Note: *10~*0: Program counter bits
S10~S0: Stack register bits
#10~#0: Instruction code bits
Rev. 1.10
@7~@0: PCL bits
5
June 29, 2007
HT82A821R
Program Memory - PROM
rupt is enabled and the stack is not full, the program
begins execution at location 00CH.
The program memory is used to store the program instructions which are to be executed. It also contains
data, table, and interrupt entries, and is organized into
2048´15 bits, addressed by the program counter and table pointer.
· Table location
Any location in the program memory can be used as
look-up tables. There are three method to read the
ROM data by two table read instructions: ²TABRDC²
and ²TABRDL², transfer the contents of the
lower-order byte to the specified data memory, and
the higher-order byte to TBLH (08H).
Only the destination of the lower-order byte in the table is well-defined, the other bits of the table word are
transferred to the lower portion of TBLH, and the remaining 1-bit words are read as ²0². The Table
Higher-order byte register (TBLH) is read only. The table pointer (TBLP, TBHP) is a read/write register (07H,
1FH), which indicates the table location. Before accessing the table, the location must be placed in the
TBLP and TBHP (If the OTP option TBHP is disabled,
the value in TBHP has no effect). The TBLH is read
only and cannot be restored. If the main routine and
the ISR (Interrupt Service Routine) both employ the
table read instruction, the contents of the TBLH in the
main routine are likely to be changed by the table read
instruction used in the ISR. Errors can occur. In other
words, using the table read instruction in the main routine and the ISR simultaneously should be avoided.
However, if the table read instruction has to be applied
in both the main routine and the ISR, the interrupt
should be disabled prior to the table read instruction. It
will not be enabled until the TBLH has been backed
up. All table related instructions require two cycles to
complete the operation. These areas may function as
normal program memory depending on the requirements.
Certain locations in the program memory are reserved
for special usage:
· Location 000H
This area is reserved for program initialization. After a
chip reset, the program always begins execution at location 000H.
· Location 004H
This area is reserved for the USB interrupt service
program. If the USB interrupt is activated, the interrupt
is enabled and the stack is not full, the program begins
execution at location 004H.
· Location 008H
This area is reserved for the Timer/Event Counter 0 interrupt service program. If a timer interrupt results
from a Timer/Event Counter 0 overflow, and if the interrupt is enabled and the stack is not full, the program
begins execution at location 008H.
· Location 00CH
This location is reserved for the Timer/Event Counter
1 interrupt service program. If a timer interrupt results
from a Timer/Event Counter 1 overflow, and the inter0 0 0 H
D e v ic e In itia liz a tio n P r o g r a m
0 0 4 H
U S B In te r r u p t S u b r o u tin e
0 0 8 H
T im e r /E v e n t C o u n te r 0
In te r r u p t S u b r o u tin e
0 0 C H
T im e r /E v e n t C o u n te r 1
In te r r u p t S u b r o u tin e
n 0 0 H
P ro g ra m
M e m o ry
Stack Register - STACK
This is a special part of the memory which is used to
save the contents of the program counter only. The
stack is organized into 16 levels and is neither part of the
data nor part of the program space, and is neither readable nor writeable. The activated level is indexed by the
stack pointer (SP) and is neither readable nor writeable.
At a subroutine call or interrupt acknowledge signal, the
contents of the program counter are pushed onto the
stack. At the end of a subroutine or an interrupt routine,
L o o k - u p T a b le ( 2 5 6 W o r d s )
n F F H
L o o k - u p T a b le ( 2 5 6 W o r d s )
7 F F H
1 5 B its
N o te : n ra n g e s fro m
0 to 7
Program Memory
Instruction
Table Location
*10
*9
*8
*7
*6
*5
*4
*3
*2
*1
*0
TABRDC [m]
P10
P9
P8
@7
@6
@5
@4
@3
@2
@1
@0
TABRDL [m]
1
1
1
@7
@6
@5
@4
@3
@2
@1
@0
Table Location
Note: *10~*0: Table location bits
P10~P8: Current program counter bits when TBHP is disabled
@7~@0: TBLP bits
Rev. 1.10
TBHP register bit2~bit0 when TBHP is enabled
6
June 29, 2007
HT82A821R
B a n k 0 S p e c ia l R e g is te r
signaled by a return instruction (RET or RETI), the program counter is restored to its previous value from the
stack. After a chip reset, the SP will point to the top of the
stack.
0 0 H
If the stack is full and a non-masked interrupt takes
place, the interrupt request flag will be recorded but the
acknowledge signal will be inhibited. When the stack
pointer is decremented (by RET or RETI), the interrupt
will be serviced. This feature prevents stack overflow allowing the programmer to use the structure more easily.
In a similar case, if the stack is full and a ²CALL² is subsequently executed, stack overflow occurs and the first
entry will be lost (only the most recent 16 return addresses are stored).
Data Memory - RAM
In d ir e c t A d d r e s s in g R e g is te r 0
0 1 H
M P 0
0 2 H
In d ir e c t A d d r e s s in g R e g is te r 1
0 3 H
M P 1
0 4 H
B P
0 5 H
A C C
0 6 H
P C L
0 7 H
T B L P
0 8 H
T B L H
0 9 H
W D T S
0 A H
S T A T U S
0 B H
IN T C 0
0 C H
T M R 0 H
0 D H
T M R 0 L
0 E H
T M R 0 C
0 F H
T M R 1 H
The data memory (RAM) is designed with 192´8 bits.
The data memory is divided into two functional groups:
namely; special function registers 54´8 bits and general
purpose data memory, Bank0: 192´8 bits. Most are
read/write, but some are read only.
1 0 H
T M R 1 L
1 1 H
T M R 1 C
The special function registers include the indirect addressing registers (R0;00H, R1;02H), Bank register (BP,
04H), Timer/Event Counter 0 higher order byte register
(TMR0H;0CH), Timer/Event Counter 0 lower order byte
register (TMR0L;0DH), Timer/Event Counter 0 control
register (TMR0C;0EH), Timer/Event Counter 1 higher
order byte register (TMR1H;0FH), Timer/Event Counter
1 lower order byte register (TMR1L;10H), Timer/Event
Counter 1 control register (TMR1C;11H), program counter lower-order byte register (PCL;06H), memory pointer
registers (MP0;01H, MP1;03H), accumulator
(ACC;05H), table pointer (TBLP;07H, TBHP;1FH), table
higher-order byte register (TBLH;08H), status register
( S TAT U S ; 0 A H ) , i n t e r r u p t c o n t r o l r e g i s t e r 0
(INTC0;0BH), Watchdog Timer option setting register
(WDTS;09H), I/O registers (PA;12H), I/O control registers (PAC;13H). Digital Volume Control Register
(USVC;1CH). USB status and control register
(USC;20H), USB endpoint interrupt status register
(USR;21H), system clock control register (UCC;22H).
Address and remote wakeup register (AWR;23H),
STALL register(24H), SIES register (25H), MISC register(26H), SETIO register(27H), FIFO0~FIFO2 register
(28H~2AH). DAC_Limit_L register (2DH), DAC_Limit_H
register (2EH), DAC_WR register (2FH).
1 B H
P A
1 3 H
P A C
1 4 H
1 C H
U S V C
1 D H
1 E H
1 F H
T B H P
2 0 H
U S C
2 1 H
U S R
2 2 H
U C C
2 3 H
A W R
2 4 H
S T A L L
2 5 H
S IE S
2 6 H
M IS C
2 7 H
S E T IO
2 8 H
F IF O 0
2 9 H
F IF O 1
2 A H
F IF O 2
2 B H
2 C H
2 D H
2 E H
2 F H
3 0 H
3 F H
4 0 H
The remaining space before the 40H is reserved for future expanded usage and reading these locations will
get ²00H². The general purpose data memory, addressed from 40H to FFH, is used for data and control
information under instruction commands.
F F H
D A C _ L im it_ L
D A C _ L im it_ H
D A C _ W R
G e n e ra l P u rp o s e
D a ta R A M
(1 9 2 B y te s )
RAM Mapping
data memory can be set and reset by ²SET [m].i² and
²CLR [m].i². They are also indirectly accessible through
memory pointer registers (MP0 or MP1).
All of the data memory areas can handle arithmetic,
logic, increment, decrement and rotate operations directly. Except for some dedicated bits, each bit in the
Rev. 1.10
1 2 H
7
June 29, 2007
HT82A821R
Indirect Addressing Register
Status Register - STATUS
Locations 00H and 02H are indirect addressing registers that are not physically implemented. Any read/write
operation on [00H] ([02H]) will access the data memory
pointed to by MP0 (MP1). Reading location 00H (02H)
indirectly will return the result 00H. Writing indirectly results in no operation.
This 8-bit register (0AH) contains the zero flag (Z), carry
flag (C), auxiliary carry flag (AC), overflow flag (OV),
power down flag (PDF), and watchdog time-out flag
(TO). It also records the status information and controls
the operation sequence.
With the exception of the TO and PDF flags, bits in the
status register can be altered by instructions like most
other registers. Any data written into the status register
will not change the TO or PDF flag. In addition, operations related to the status register may give different results from those intended.
The function of data movement between two indirect addressing registers is not supported. The memory pointer
registers (MP0 and MP1) are 8-bit registers used to access the RAM by combining corresponding indirect addressing registers.
The TO flag can be affected only by a system power-up,
a WDT time-out or executing the ²CLR WDT² or ²HALT²
instruction. The PDF flag can be affected only by executing the ²HALT² or ²CLR WDT² instruction or during a
system power-up.
Bank Pointer
The bank pointer is used to assign the accessed RAM
bank. When the users want to access the RAM bank 0, a
²0² should be loaded onto BP. RAM locations before
40H in any bank are overlapped.
The Z, OV, AC and C flags generally reflect the status of
the latest operations.
Accumulator
The accumulator is closely related to ALU operations. It
is also mapped to location 05H of the data memory and
can carry out immediate data operations. The data
movement between two data memory locations must
pass through the accumulator.
In addition, upon entering the interrupt sequence or executing a subroutine call, the status register will not be
automatically pushed onto the stack. If the contents of
the status are important and if the subroutine can corrupt the status register, precautions must be taken to
save it properly.
Arithmetic and Logic Unit - ALU
Interrupt
This circuit performs 8-bit arithmetic and logic operations. The ALU provides the following functions:
The device provides USB interrupt and internal
timer/event counter interrupts. The Interrupt Control
Register0 (INTC0;0BH) contains the interrupt control
bits that are used to set the enable/disable status and interrupt request flags.
· Arithmetic operations (ADD, ADC, SUB, SBC, DAA)
· Logic operations (AND, OR, XOR, CPL)
· Rotation (RL, RR, RLC, RRC)
· Increment and Decrement (INC, DEC)
Once an interrupt subroutine is serviced, all the other interrupts will be blocked (by clearing the EMI bit). This
scheme may prevent any further interrupt nesting. Other
interrupt requests may occur during this interval but only
· Branch decision (SZ, SNZ, SIZ, SDZ ....)
The ALU not only saves the results of a data operation
but also changes the status register.
Bit No.
Label
Function
0
C
C is set if an operation results in a carry during an addition operation or if a borrow does not
take place during a subtraction operation; otherwise C is cleared. C is also affected by a rotate
through carry instruction.
1
AC
AC is set if an operation results in a carry out of the low nibbles in addition or no borrow from
the high nibble into the low nibble in subtraction; otherwise AC is cleared.
2
Z
3
OV
OV is set if an operation results in a carry into the highest-order bit but not a carry out of the
highest-order bit, or vice versa; otherwise OV is cleared.
4
PDF
PDF is cleared by a system power-up or executing the ²CLR WDT² instruction. PDF is set by
executing the ²HALT² instruction.
5
TO
TO is cleared by a system power-up or executing the ²CLR WDT² or ²HALT² instruction. TO is
set by a WDT time-out.
6~7
¾
Unused bit, read as ²0²
Z is set if the result of an arithmetic or logic operation is zero; otherwise Z is cleared.
Status (0AH) Register
Rev. 1.10
8
June 29, 2007
HT82A821R
the interrupt request flag is recorded. If a certain interrupt requires servicing within the service routine, the
EMI bit and the corresponding bit of the INTC may be
set to allow interrupt nesting. If the stack is full, the interrupt request will not be acknowledged, even if the related interrupt is enabled, until the SP is decremented. If
immediate service is desired, the stack must be prevented from becoming full.
set and a USB interrupt is triggered.
All these kinds of interrupts have a wake-up capability.
As an interrupt is serviced, a control transfer occurs by
pushing the program counter onto the stack, followed by
a branch to a subroutine at a specified location in the
program memory. Only the program counter is pushed
onto the stack. If the contents of the register or status
register (STATUS) are altered by the interrupt service
program which corrupts the desired control sequence,
the contents should be saved in advance.
The internal Timer/Even Counter 1 interrupt is initialized
by setting the Timer/Event Counter 1 interrupt request
flag (bit 6 of INTC0), caused by a timer 1 overflow. When
the interrupt is enabled, the stack is not full and the T1F
is set, a subroutine call to location 0CH will occur. The
related interrupt request flag (T1F) will be reset and the
EMI bit cleared to disable further interrupts.
The internal Timer/Event Counter 0 interrupt is initialized by setting the Timer/Event Counter 0 interrupt request flag (bit 5 of INTC0), caused by a timer 0 overflow.
When the interrupt is enabled, the stack is not full and
the T0F bit is set, a subroutine call to location 08H will
occur. The related interrupt request flag (T0F) will be reset and the EMI bit cleared to disable further interrupts.
During the execution of an interrupt subroutine, other interrupt acknowledge signals are held until the ²RETI² instruction is executed or the EMI bit and the related
interrupt control bit are set to 1 (if the stack is not full). To
return from the interrupt subroutine, ²RET² or ²RETI²
may be invoked. RETI will set the EMI bit to enable an
interrupt service, but RET will not.
The USB interrupts are triggered by the following USB
events and the related interrupt request flag (USBF; bit
4 of the INTC0) will be set.
· Access of the corresponding USB FIFO from PC
· The USB suspend signal from PC
· The USB resume signal from PC
Interrupts, occurring in the interval between the rising
edges of two consecutive T2 pulses, will be serviced on
the latter of the two T2 pulses, if the corresponding interrupts are enabled. In the case of simultaneous requests
the following table shows the priority that is applied.
These can be masked by resetting the EMI bit.
· USB Reset signal
When the interrupt is enabled, the stack is not full and
the external interrupt is active, a subroutine call to location 04H will occur. The interrupt request flag (USBF)
and EMI bits will be cleared to disable other interrupts.
When PC Host access the FIFO of the HT82A821R, the
corresponding request bit of USR is set, and a USB interrupt is triggered. So user can easy to decide which
FIFO is accessed. When the interrupt has been served,
the corresponding bit should be cleared by firmware.
When HT82A821R receive a USB Suspend signal from
Host PC, the suspend line (bit0 of USC) of the
HT82A821R is set and a USB interrupt is also triggered.
No.
Also when HT82A821R receive a Resume signal from
Host PC, the resume line (bit3 of USC) of HT82A821R is
Label
0
EMI
Priority Vector
a
USB interrupt
1
04H
b
Timer/Event Counter 0 overflow
2
08H
c
Timer/Event Counter 1 overflow
3
0CH
It is recommended that a program does not use the
²CALL subroutine² within the interrupt subroutine. Interrupts often occur in an unpredictable manner or need to
be serviced immediately in some applications. If only
one stack is left and enabling the interrupt is not well
controlled, the original control sequence will be damaged once the ²CALL² operates in the interrupt subroutine.
When the HT82A821R receives a Resume signal from
the Host PC, the resume line (bit3 of the USC) of the
HT82A821R are set and a USB interrupt is triggered.
Bit No.
Interrupt Source
Function
Controls the master (global) interrupt (1=enable; 0=disable)
1
EUI
Controls the USB interrupt (1=enable; 0= disable)
2
ET0I
Controls the Timer/Event Counter 0 interrupt (1=enable; 0=disable)
3
ET1I
Controls the Timer/Event Counter 1 interrupt (1=enable; 0=disable)
4
USBF
USB interrupt request flag (1=active; 0=inactive)
5
T0F
Internal Timer/Event Counter 0 request flag (1:active; 0:inactive)
6
T1F
Internal Timer/Event Counter 1 request flag (1:active; 0:inactive)
7
¾
Unused bit, read as ²0²
INTC0 (0BH) Register
Rev. 1.10
9
June 29, 2007
HT82A821R
Oscillator Configuration
The WDT OSC period is typical 65ms. This time-out period may vary with temperature, VDD and process variations. The WDT OSC always works for any operation
mode.
There is an oscillator circuit in the microcontroller.
O S C I
If the instruction clock is selected as the WDT clock
source, the WDT operates in the same manner except in
the halt mode. In the mode, the WDT stops counting and
lose its protecting purpose. In this situation the logic can
only be re-started by external logic. The high nibble and
bit3 of the WDTS are reserved for user defined flags,
which can be used to indicate some specified status.
O S C O
C r y s ta l O s c illa to r
System Oscillator
This oscillator is designed for system clocks. The HALT
mode stops the system oscillator and ignores an external signal to conserve power.
The WDT overflow under normal operation initializes a
²chip reset² and sets the status bit ²TO². In the HALT
mode, the overflow initializes a ²warm reset², and only
the PC and SP are reset to zero. To clear the contents of
the WDT, there are three methods to be adopted, i.e.,
external reset (a low level to RESET), software instruction, and a ²HALT² instruction. There are two types of
software instructions; ²CLR WDT² and the other set
²CLR WDT1² and ²CLR WDT2². Of these two types of
instruction, only one type of instruction can be active at a
time depending on the options ²CLR WDT² times selection option. If the ²CLR WDT² is selected (i.e., CLR WDT
times equal one), any execution of the ²CLR WDT² instruction clears the WDT. In the case that ²CLR WDT1²
and ²CLR WDT2² are chosen (i.e., CLR WDT times
equal two), these two instructions have to be executed
to clear the WDT; otherwise, the WDT may reset the
chip due to time-out.
A crystal across OSCI and OSCO is needed to provide
the feedback and phase shift required for the oscillator.
No other external components are required. Instead of a
crystal, a resonator can also be connected between
OSCI and OSCO to get a frequency reference, but two
external capacitors in OSCI and OSCO are required.
The WDT oscillator is a free running on-chip RC oscillator, and no external components are required. Even if
the system enters the power down mode, the system
clock is stopped, but the WDT oscillator still works. The
WDT oscillator can be disabled by ROM code option to
conserve power.
Watchdog Timer - WDT
The WDT clock source is implemented by a dedicated
RC oscillator (WDT oscillator) or a instruction clock (system clock/4). The timer is designed to prevent a software malfunction or sequence from jumping to an
unknown location with unpredictable results. The WDT
can be disabled by options. But if the WDT is disabled,
all executions related to the WDT lead to no operation.
W D T O S C
S y s te m C lo c k /4
When the WDT clock source is selected, it will be first divided by 256 (8-stage) to get the nominal time-out period. By invoking the WDT prescaler, longer time-out
periods can be realized. Writing data to WS2, WS1,
WS0 can give different time-out periods.
Bit No.
WS0
WS1
WS2
3
¾
7~4
T3~T0
W D T P r e s c a le r
8 - b it C o u n te r
7 - b it C o u n te r
W S 0 ~ W S 2
8 -to -1 M U X
W D T T im e - o u t
Watchdog Timer
Label
0
1
2
M a s k
O p tio n
S e le c t
Function
Watchdog Timer division ratio selection bits
Bit 2,1,0 = 000, division ratio = 1:1
Bit 2,1,0 = 001, division ratio = 1:2
Bit 2,1,0 = 010, division ratio = 1:4
Bit 2,1,0 = 011, division ratio = 1:8
Bit 2,1,0 = 100, division ratio = 1:16
Bit 2,1,0 = 101, division ratio = 1:32
Bit 2,1,0 = 110, division ratio = 1:64
Bit 2,1,0 = 111, division ratio = 1:128
Unused bit, read as ²0²
Test mode setting bits
(T3, T2, T1, T0)=(0, 1, 0, 1), enter DAC write mode. Otherwise normal operation.
WDTS (09H) Register
Rev. 1.10
10
June 29, 2007
HT82A821R
Power Down Operation - HALT
The WDT time-out during HALT is different from other
chip reset conditions, since it can perform a ²warm re set² that resets only the program counter and SP, leaving the other circuits in their original state. Some registers remain unchanged during other reset conditions.
Most registers are reset to the ²initial condition² when
the reset conditions are met. By examining the PDF and
TO flags, the program can distinguish between different
²chip resets².
The HALT mode is initialized by the ²HALT² instruction
and results in the following:
· The system oscillator will be turned off but the WDT
oscillator remains running (if the WDT oscillator is selected).
· The contents of the on-chip RAM and registers remain
unchanged.
· The WDT and WDT prescaler will be cleared and re-
counted again (if the WDT clock is from the WDT oscillator).
· All of the I/O ports remain in their original status.
TO PDF
RESET Conditions
0
0
RESET reset during power-up
· The PDF flag is set and the TO flag is cleared.
u
u
RESET reset during normal operation
The system can leave the HALT mode by means of an
external reset, an interrupt, an external falling edge signal on port A or a WDT overflow. An external reset
causes a device initialization and the WDT overflow performs a ²warm reset². After the TO and PDF flags are
examined, the cause for chip reset can be determined.
The PDF flag is cleared by a system power-up or executing the ²CLR WDT² instruction and is set when executing the ²HALT² instruction. The TO flag is set if the
WDT time-out occurs, and causes a wake-up that only
resets the program counter and SP; the others remain in
their original status.
0
1
RESET wake-up HALT
1
u
WDT time-out during normal operation
1
1
WDT wake-up HALT
Note: ²u² stands for ²unchanged²
To guarantee that the system oscillator is started and
stabilized, the SST (System Start-up Timer) provides an
extra delay of 1024 system clock pulses when the system resets (power-up, WDT time-out or RES reset) or
the system awakes from the HALT state.
When a system reset occurs, the SST delay is added
during the reset period. Any wake-up from HALT will enable the SST delay.
The port A wake-up and interrupt methods can be considered as a continuation of normal execution. Each bit
in port A can be independently selected to wake-up the
device by mask option. Awakening from an I/O port stimulus, the program will resume execution of the next instruction. If it awakens from an interrupt, two sequence
may occur. If the related interrupt is disabled or the interrupt is enabled but the stack is full, the program will resume execution at the next instruction. If the interrupt is
enabled and the stack is not full, the regular interrupt response takes place. If an interrupt request flag is set to
²1² before entering the HALT mode, the wake-up function of the related interrupt will be disabled. Once a
wake-up event occurs, it takes 1024 tSYS (system clock
period) to resume normal operation. In other words, a
dummy period will be inserted after a wake-up. If the
wake-up results from an interrupt acknowledge signal,
the actual interrupt subroutine execution will be delayed
by one or more cycles. If the wake-up results in the next
instruction execution, this will be executed immediately
after the dummy period is finished.
V
D D
R E S E T
Reset Circuit
V D D
R E S
tS
S S T T im e - o u t
C h ip
R e s e t
Reset Timing Chart
H A L T
W a rm
R e s e t
W D T
To minimize power consumption, all the I/O pins should
be carefully managed before entering the HALT status.
R E S E T
Reset
There are four ways in which a reset can occur:
O S C I
· RES reset during normal operation
· RES reset during HALT
S S T
1 0 - b it R ip p le
C o u n te r
S y s te m
· WDT time-out reset during normal operation
C o ld
R e s e t
R e s e t
Reset Configuration
· USB reset
Rev. 1.10
S T
11
June 29, 2007
HT82A821R
The functional unit chip reset status are shown below.
Program Counter
000H
Interrupt
Disable
WDT
Clear. After master reset,WDT begins counting
Timer/event Counter
Off
Input/output Ports
Input mode
Stack Pointer
Points to the top of the stack
The registers status are summarized in the following table.
Reset
(Power On)
WDT
Time-out
(Normal
Operation)
RES Reset
(Normal
Operation)
RES Reset
(HALT)
WDT
Time-Out
(HALT)*
USB-Reset
(Normal)
USB-Reset
(HALT)
MP0
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
MP1
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
ACC
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
000H
000H
000H
000H
000H
000H
000H
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
Register
Program
Counter
TBLP
TBLH
-xxx xxxx
-uuu uuuu
-uuu uuuu
-uuu uuuu
-uuu uuuu
-uuu uuuu
-uuu uuuu
WDTS
0000 0111
0000 0111
0000 0111
0000 0111
uuuu uuuu
0000 0111
0000 0111
STATUS
--00 xxxx
--1u uuuu
--uu uuuu
--01 uuuu
--11 uuuu
--uu uuuu
--01 uuuu
INTC0
-000 0000
-000 0000
-000 0000
-000 0000
-uuu uuuu
-000 0000
-000 0000
TMR0H
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
TMR0L
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
TMR0C
00-0 1000
00-0 1000
00-0 1000
00-0 1000
uu-u uuuu
00-0 1000
00-0 1000
TMR1H
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
TMR1L
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
TMR1C
00-0 1---
00-0 1---
00-0 1---
00-0 1---
uu-u u---
00-0 1---
00-0 1---
PA
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
1111 1111
1111 1111
PAC
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
1111 1111
1111 1111
USC
1000 0000
uuxx uuuu
10xx 0000
10xx 0000
10xx uuuu
1000 0u00
1000 0u00
USR
0000 0000
uuuu uuuu
0000 0000
0000 0000
uuuu uuuu
00uu 0000
00uu 0000
UCC
0000 0000
uuuu uuuu
0000 0000
0000 0000
uuuu uuuu
0u00 u000
0u00 u000
AWR
0000 0000
uuuu uuuu
0000 0000
0000 0000
uuuu uuuu
0000 0000
0000 0000
STALL
0000 0000
uuuu uuuu
0000 0000
0000 0000
uuuu uuuu
0000 0000
0000 0000
SIES
0000 0000
uuuu uuuu
0000 0000
0000 0000
uuuu uuuu
0u00 u000
0u00 u000
MISC
0000 0000
uuuu uuuu
0000 0000
0000 0000
uuuu uuuu
0000 0000
0000 0000
SETIO
xxxx x010
xxxx x010
xxxx x010
xxxx x010
xxxx x010
xxxx x010
xxxx x010
FIFO0
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
0000 0000
0000 0000
FIFO1
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
0000 0000
0000 0000
FIFO2
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
0000 0000
0000 0000
DAC_LIMIT_L
0000 0000
0000 0000
0000 0000
0000 0000
uuuu uuuu
0000 0000
0000 0000
DAC_LIMIT_H
0000 0000
0000 0000
0000 0000
0000 0000
uuuu uuuu
0000 0000
0000 0000
DAC_WR
0000 0000
0000 0000
0000 0000
0000 0000
uuuu uuuu
0000 0000
0000 0000
Note: ²*² stands for ²warm reset²
²u² stands for ²unchanged²
²x² stands for ²unknown²
²_² stands for ²undefined²
Rev. 1.10
12
June 29, 2007
HT82A821R
(TMR0, TMR1) pin. The timer mode functions as a normal timer with the clock source coming from the internal
clock source. Finally, the pulse width measurement
mode can be used to count the high level or low level duration of the external signal (TMR0, TMR1), and the
counting is based on the internal clock source.
Timer/Event Counter
Two timer/event counters (TMR0, TMR1) are implemented in the microcontroller. The timer/event counter
0/1 contains a 16-bit programmable count-up counter
and the clock may come from an external source or an
internal clock source. An internal clock source comes
from fSYS/4. The external clock input allows the user to
count external events, measure time intervals or pulse
widths, or to generate an accurate time base. There are
six registers related to the Timer/Event Counter 0;
TMR0H (0CH), TMR0L (0DH), TMR0C (0EH) and the
Timer/Event Counter 1; TMR1H (0FH), TMR1L (10H),
TMR1C (11H). For 16-bit timer to write data to TMR0/1L
will only put the written data to an internal lower-order
byte buffer (8-bit) and writing TMR0/1H will transfer the
specified data and the contents of the lower-order byte
buffer to TMR0/1H and TMR0/1L registers. The
Timer/Event Counter 0/1 preload register is changed by
each writing TMR0/1H operations. Reading TMR0/1H
will latch the contents of TMR0/1H and TMR0/1L counters to the destination and the lower-order byte buffer,
respectively. Reading the TMR0/1L will read the contents of the lower-order byte buffer. The TMR0/1C is the
Timer/Event Counter 0/1 control register, which defines
the operating mode, counting enable or disable and an
active edge.
In the event count or timer mode, the timer/event counter starts counting at the current contents in the
timer/event counter and ends at FFFFH. Once an overflow occurs, the counter is reloaded from the timer/event
counter preload register, and generates an interrupt request flag (T0F; bit 5 of INTC0, T1F; bit 6 of INTC0). In
the pulse width measurement mode with the values of
the TON and TE bits equal to 1, after the TMR0 (TMR1)
has received a transient from low to high (or high to low if
the TE bit is ²0²), it will start counting until the TMR0
(TMR1) returns to the original level and resets the TON.
The measured result remains in the timer/event counter
even if the activated transient occurs again. In other
words, only 1-cycle measurement can be made until the
TON is set. The cycle measurement will re-function as
long as it receives further transient pulse. In this operation mode, the timer/event counter begins counting not
according to the logic level but to the transient edges. In
the case of counter overflows, the counter is reloaded
from the timer/event counter register and issues an interrupt request, as in the other two modes, i.e., event
and timer modes.
The TM0 and TM1 bits define the operation mode. The
event count mode is used to count external events,
which means that the clock source is from an external
Bit No.
Label
0~2, 5
¾
Unused bit, read as ²0²
3
TE
Defines the TMR active edge of the timer/event counter
In Event counter mode (TM1, TM0)=(0, 1):
1=count on falling edge;
0=count on rising edge
In Pulse width measurement mode (TM1, TM0)=(1, 1):
1=start counting on the rising edge, stop on the falling edge;
0=start counting on the falling edge, stop on the rising edge
4
TON
Enable/disable the timer counting (0=disable; 1=enable)
TM0
TM1
Defines the operating mode
01=Event count mode (external clock)
10=Timer mode (internal clock)
11=Pulse width measurement mode
00=Unused
6
7
Function
TMRC (11H) Register
fS
Y S /4
f IN
D a ta B u s
T
T M 1
T M 0
T M R 0 /1
1 6 B its
T im e r /E v e n t C o u n te r
P r e lo a d R e g is te r
R e lo a d
T E
T M 1
T M 0
T O N
P u ls e W id th
M e a s u re m e n t
M o d e C o n tro l
1 6 B its
T im e r /E v e n t C o u n te r
(T M R 0 /1 )
O v e r flo w
to In te rru p t
Timer/Event Counter 0/1
Rev. 1.10
13
June 29, 2007
HT82A821R
Each I/O line has its own control register (PAC) to control the input/output configuration. With this control register, CMOS output or Schmitt trigger input with or
without pull-high resistor structures can be reconfigured
dynamically (i.e., on-the-fly) under software control. To
function as an input, the corresponding latch of the control register must write ²1². The input source also depends on the control register. If the control register bit is
²1² the input will read the pad state. If the control register
bit is ²0² the contents of the latches will move to the internal bus. The latter is possible in the ²Read-modifywrite² instruction. For output function, CMOS configurations can be selected. The control register is mapped to
location 13H.
To enable the counting operation, the Timer ON bit
(TON; bit 4 of TMR0C or TMR1C) should be set to 1. In
the pulse width measurement mode, TON is automatically cleared after the measurement cycle is completed.
But in the other two modes, the TON can only be reset
by instructions. The overflow of the Timer/Event Counter 0/1 is one of the wake-up sources. No matter what
the operation mode is, writing a 0 to ET0I or ET1I disables the related interrupt service.
In the case of timer/event counter OFF condition, writing
data to the timer/event counter preload register also reloads that data to the timer/event counter. But if the
timer/event counter is turn on, data written to the
timer/event counter is kept only in the timer/event counter preload register. The timer/event counter still continues its operation until an overflow occurs.
After a chip reset, these input/output lines remain at high
levels or in a floating state (depending on the
pull-high/low options). Each bit of these input/output
latches can be set or cleared by ²SET [m].i² and ²CLR
[m].i² (m=12H) instructions.
When the timer/event counter (reading TMR0/TMR1) is
read, the clock is blocked to avoid errors, as this may results in a counting error. Blocking of the clock should be
taken into account by the programmer.
Some instructions first input data and then follow the
output operations. For example, ²SET [m].i², ²CLR
[m].i², ²CPL [m]², ²CPLA [m]² read the entire port states
into the CPU, execute the defined operations
(bit-operation), and then write the results back to the
latches or the accumulator.
Input/Output Ports
There are 8 bidirectional input/output lines (PA) in the
microcontroller, which are mapped to the data memory
of [12H] respectively. All of these I/O ports can be used
for input and output operations. For input operation,
these ports are non-latching, that is, the inputs must be
ready at the T2 rising edge of instruction ²MOV A,[m]²
(m=12H). For output operation, all the data is latched
and remains unchanged until the output latch is rewritten.
Each line of port A has the capability of waking-up the
device.
It is recommended that unused or not bonded out I/O
lines should be set as output pins by software instruction
to avoid consuming power under input floating state.
V
D a ta B u s
W r ite C o n tr o l R e g is te r
D D
C o n tr o l B it
P u ll- h ig h
Q
D
Q
C K
S
C h ip R e s e t
R e a d C o n tr o l R e g is te r
W r ite D a ta R e g is te r
P A 0 ~ P A 7
D a ta B it
Q
D
C K
S
Q
M
R e a d D a ta R e g is te r
S y s te m
U
X
W a k e - u p ( P A o n ly )
M a s k O p tio n
Input/Output Ports
Rev. 1.10
14
June 29, 2007
HT82A821R
Low Voltage Reset - LVR (by ROM Code Option)
the Resume line (bit 3 of USC) is set. In order to make
HT82A821R work properly, the firmware must set the
USBCKEN (bit 3 of UCC) to 1 and clear the SUSP2 (bit4
of the UCC). Since the Resume signal will be cleared
before the Idle signal is sent out by the host and the Suspend line (bit 0 of USC) is going to ²0². So when the
MCU is detecting the Suspend line (bit0 of USC), the
Resume line should be remembered and token into consideration. The following is the timing diagram:
The LVR option is 3.0V.
The microcontroller provides low voltage reset circuit in
order to monitor the supply voltage of the device. If the
supply voltage of the device is within the range
0.9V~VLVR such as changing a battery, the LVR will automatically reset the device internally.
The LVR includes the following specifications:
· The low voltage (0.9V~VLVR) has to remain in their
S U S P E N D
original state to exceed 1ms. If the low voltage state
does not exceed 1ms, the LVR will ignore it and do not
perform a reset function.
U S B R e s u m e S ig n a l
· The LVR uses the ²OR² function with the external
U S B _ IN T
RESET signal to perform chip reset.
Suspend Wake-Up and Remote Wake-Up
The device with remote wake up function can wake-up
the USB Host by sending a wake-up pulse through
RMWK (bit 1 of USC). Once the USB Host receive the
wake-up signal from HT82A821R, it will send a Resume
signal to device. The timing as follow:
If there is no signal on the USB bus for over 3ms, the
HT82A821R will go into a suspend mode. The Suspend
line (bit 0 of the USC) will be set to ²1² and a USB interrupt is triggered to indicate that the HT82A821R should
jump to the suspend state to meet the USB suspend current spec.
S U S P E N D
M in . 1 U S B C L K
In order to meet the suspend current, the firmware
should disable the USB clock by clearing the USBCKEN
(bit3 of the UCC) to ²0².
R M W K
Also the user can further decrease the suspend current
by set the SUSP2 (bit4 of the UCC).
U S B R e s u m e S ig n a l
U S B _ IN T
When the resume signal is sent out by the host, the
HT82A821R will wake up the MCU by USB interrupt and
Rev. 1.10
M in .2 .5 m s
15
June 29, 2007
HT82A821R
USB Interface
The HT82A821R have 3 Endpoints (EP0 ~EP2). EP0 supports Control transfer. EP1 supports Interrupt transfer. EP2
supports Isochronous transfer.
These registers, including USC (20H), USR (21H), UCC (22H), AWR (23H), STALL (24H ), SIES (25H), MISC (26H),
SETIO (27H), FIFO0 (28H), FIFO1 (29H), FIFO2 (2AH) used for the USB function.
The FIFO size of each FIFO is 8 byte (FIFO0), 8 byte (FIFO1), 384 byte (FIFO2), and total are 400 bytes.
URD (bit7 of USC) is USB reset signal control function definition bit.
Bit No.
Label
R/W
Reset
Functions
0
SUSP
R
0
Read only, USB suspend indication. When this bit is set to ²1² (set
by SIE), it indicates the USB bus enters suspend mode. The USB interrupt is also triggered on changing from low to high of this bit.
1
RMWK
R/W
0
USB remote wake-up command. It is set by MCU to force the USB
host leaving the suspend mode.
0
USB reset indication. This bit is set/cleared by USB SIE. This bit is
used to detect USB reset event on USB bus. When this bit is set to
²1², this indicates an USB reset is occurred and an USB interrupt will
be initialized.
2
URST
R/W
3
RESUME
R
0
USB resume indication. When the USB leaves suspend mode, this
bit is set to ²1² (set by SIE). When the RESUME is set by SIE, an interrupt will be generated to wake-up the MCU. In order to detecting
the suspend state, MCU should set USBCKEN and clear SUSP2 (in
UCC register) to enable the SIE detecting function. The RESUME
will be cleared while the SUSP is going ²0². When MCU is detecting
the SUSP, the RESUME (causes MCU to wake-up) should be remembered and token into consideration.
4
V33O
R/W
0
0/1: Turn-off/on V33O output
5~6
¾
¾
¾
Undefined bit, read as ²0².
7
URD
R/W
1
USB reset signal control function definition
1: USB reset signal will reset MCU
0: USB reset signal cannot reset MCU
USC (20H) Register
The USR (USB endpoint interrupt status register) register is used to indicate which endpoint is accessed and to select
serial bus (USB). The endpoint request flags (EP0F, EP1F, EP2F) are used to indicate which endpoints are accessed. If
an endpoint is accessed, the related endpoint request flag will be set to ²1² and the USB interrupt will occur (if USB interrupt is enabled and the stack is not full). When the active endpoint request flag is served, the endpoint request flag
has to be cleared to ²0² by software.
Bit No.
Label
R/W
Reset
Functions
0
EP0F
R/W
0
When this bit is set to ²1² (set by SIE). It indicates the endpoint 0 is
accessed and an USB interrupt will occur. When the interrupt has
been served, this bit should be cleared by software.
1
EP1F
R/W
0
When this bit is set to ²1² (set by SIE). It indicates the endpoint 1 is
accessed and an USB interrupt will occur. When the interrupt has
been served, this bit should be cleared by software.
2
EP2F
R/W
0
When this bit is set to ²1² (set by SIE). It indicates the endpoint 2 is
accessed and an USB interrupt will occur. When the interrupt has
been served, this bit should be cleared by software.
3~7
¾
¾
¾
Undefined bit, read as ²0².
USR (21H) Register
Rev. 1.10
16
June 29, 2007
HT82A821R
There is a system clock control register implemented to select the clock used in the MCU. This register consists of USB
clock control bit (USBCKEN), second suspend mode control bit (SUSP2) and system clock selection (SYSCLK)
And to define which endpoint FIFO is select by EPS2, EPS1 and EPS0.
Bit No.
Label
R/W
Reset
Functions
0~2
EPS0~EPS2
R/W
0
Accessing endpoint FIFO selection, EPS2, EPS1, EPS0:
000: Select endpoint 0 FIFO
001: Select endpoint 1 FIFO
010: Select endpoint 2 FIFO
011: reserved for future expansion, cannot be used
100: reserved for future expansion, cannot be used
101: reserved for future expansion, cannot be used
110: reserved for future expansion, cannot be used
111: reserved for future expansion, cannot be used
If the selected endpoints are not existed, the related functions will be
absent.
3
USBCKEN
R/W
0
USB clock control bit. When this bit is set to ²1², it indicates that the
USB clock is enabled.
Otherwise, the USB clock is turned-off.
4
SUSP2
R/W
0
This bit is used for reducing power consumption in suspend mode.
In normal mode, clean this bit to ²0²
In HALT mode, set this bit to ²1² for reducing power consumption.
5
fSYS24MHz
R/W
0
This bit is used to define the MCU system clock comes form external
OSC or system clock comes PLL output 24MHz clock.
0: system clock comes from OSC
1: system clock comes from PLL output 24MHz
0
This bit is used to specify the system clock oscillator frequency used
by MCU.
If a 6MHz crystal oscillator or resonator is used, this bit should be set
to ²1².
If a 12MHz crystal oscillator or resonator is used. this bit should be
cleared to ²0².
6
SYSCLK
R/W
UCC (22H) Register
Note: Isochronous endpoint 2 is implemented by hardware, so FIFO2 can not read/write by firmware.
AWR register contains current address and a remote wake up function control bit. The initial value of AWR is ²00H².
The address value extracted from the USB command has not to be loaded into this register until the SETUP stage being finished.
Bit No.
Label
R/W
Power-on
Functions
0
WKEN
R/W
0
USB remote-wake-up enable/disable (1/0)
1~7
AD0~AD6
R/W
0
USB device address
AWR (23H) Register
STALL register shows where the corresponding endpoint works properly or not. As soon as the endpoint works improperly, the related bit in the STALL has to be set to ²1². The STALL will be cleared by USB reset signal.
Bit No.
Label
R/W
Power-on
Functions
0~2
STL0~STL2
R/W
0
Set by users when related USB endpoints were stalled. They are
cleared by USB reset and Setup Token event.
3~7
STL3~STL7
¾
0
Undefined bit, read as ²0².
STALL (24H) Register
Rev. 1.10
17
June 29, 2007
HT82A821R
Bit No.
Label
R/W
Power-on
Functions
0
ASET
R/W
0
This bit is used to configure the SIE automatically change the device address by the value stored in the AWR register. When this bit is set to ²1²
by firmware, the SIE will update the device address by the value stored
in the AWR register after PC host is successfully read the data from device by IN operation. Otherwise, when this bit is cleared to ²0², the SIE
will update the device address immediately after an address is written to
the AWR register. So, in order to work properly, firmware has to clear
this bit after next valid SETUP token is received.
1
ERR
R/W
0
This bit is used to indicate there are some errors occurred during the
FIFO0 is accessed. This bit is set by SIE and should be cleared by firmware.
2
OUT
R/W
0
This bit is used to indicate there are OUT token (except the OUT zero
length token) has been received. The firmware clears this bit after the
OUT data has been read. Also, this bit will be cleared by SIE after the
next valid SETUP token is received.
3
IN
R
0
This bit is used to indicate the current USB receiving signal from PC host
is IN token.
4
NAK
R
0
This bit is used to indicate the SIE is transmitted NAK signal to host in response to PC host IN or OUT token.
5
CRCF
R/W
0
Error condition failure flag include CRC, PID, no integrate token error,
CRCF will be set by hardware and the CRCF need to be cleared by firmware.
6
EOT
R
1
Token package active flag, low active.
0
NAK token interrupt mask flag. If this bit set, when device sent a NAK token to host, the interrupt will not happen. Otherwise when this bit is
cleared, device sent a NAK token to host will enter the interrupt
sub-routine.
7
NMI
R/W
SIES (25H) Register
MISC register combines a command and status to control desired endpoint FIFO action and to show the status of
wanted endpoint FIFO. The MISC will be cleared by USB reset signal.
Bit No.
Label
R/W
Power-on
Functions
0
REQUEST
R/W
0
After setting others status of desired one, FIFO can be requested by setting this bit high active. After work has been done, this bit must be set
low.
1
TX
R/W
0
To represent the direction and transition end MCU accesses, When being set logic 1, MCU wants to write data to FIFO. After the work being
done, this bit must be set logic 0 before terminating request to represent
transition end. For reading action, this bit must be set logic 0 to represent
MCU want to read and must be set logic 1 after the work done.
2
CLEAR
R/W
0
To represent MCU clear requested FIFO, even the FIFO is not ready. After clearing the FIFO, USB interface will send force_tx_err to tell Host
that data under-run if Host want to read data.
3
¾
R
0
Undefined bit, read as ²0².
4
ISOEN-
R/W
0
To enable the isochronous pipe interrupt.
5
SETCMD
R/W
0
To show that the data in FIFO is setup command. This bit will last this
state until next one entering the FIFO.
6
READY
R
0
To tell that the desired FIFO is ready to work.
7
LEN0
R
0
To tell that host sent a 0-sized packet to MCU. This bit must be cleared
by read action to corresponding FIFO.
USB MISC (26H) Register
Rev. 1.10
18
June 29, 2007
HT82A821R
Bit No.
Label
R/W
Power-on
Functions
0
DATATG*
R/W
0
To toggle this bit, all the DATA token will send DATA0 first.
1
SETIO1**
R/W
1
Set endpoint1 input or output pipe (1/0), default input pipe(1)
2
SETIO2**
R/W
0
Set endpoint2 input or output pipe (1/0), default output pipe(0)
3~7
¾
¾
¾
Reserved
SETIO Register, USB Endpoint 1~Endpoint 2 Set IN/OUT Pipe Register
Note: *USB definition: when host send a ²set Configuration², the Data pipe should send the DATA0 (about the Data
toggle) first. So, when Device received a ²set configuration² setup command, user need to toggle this bit for
next data will send a Data0 first.
**Only need to set the data pipe as a input pile or output pile. The purpose of this function is to avoid the host
sent a abnormal IN or OUT token and make the endpoint disability.
Bit No.
Label
R/W
Power-on
Functions
0~6
USVC0~
USVC6
R/W
0
Volume control Bit0~Bit6
7
MUTE
R/W
0
Mute control, low active.
USB Speaker Volume Control
Result (dB)
USVC
Result (dB)
USVC
Result (dB)
USVC
Result (dB)
USVC
6
000_1100
-2
111_1100
-10
110_1100
-24
101_1100
5.5
000_1011
-2.5
111_1011
-10.5
110_1011
-25
101_1011
5
000_1010
-3
111_1010
-11
110_1010
-26
101_1010
4.5
000_1001
-3.5
111_1001
-11.5
110_1001
-27
101_1001
4
000_1000
-4
111_1000
-12
110_1000
-28
101_1000
3.5
000_0111
-4.5
111_0111
-13
110_0111
-29
101_0111
3
000_0110
-5
111_0110
-14
110_0110
-30
101_0110
2.5
000_0101
-5.5
111_0101
-15
110_0101
-31
101_0101
2
000_0100
-6
111_0100
-16
110_0100
-32
101_0100
1.5
000_0011
-6.5
111_0011
-17
110_0011
¾
¾
1
000_0010
-7
111_0010
-18
110_0010
¾
¾
0.5
000_0001
-7.5
111_0001
-19
110_0001
¾
¾
0
000_0000
-8
111_0000
-20
110_0000
¾
¾
-0.5
111_1111
-8.5
110_1111
-21
101_1111
¾
¾
-1
111_1110
-9
110_1110
-22
101_1110
¾
¾
-1.5
111_1101
-9.5
110_1101
-23
101_1101
¾
¾
Speaker mute Control:
MUTE= 0: Mute Speaker output.
MUTE= 1: Normal.
Registers
FIFO0~
FIFO2
R/W
R/W
Power-on
Functions
xxH
EPi accessing register (i = 0~2). When an endpoint is disabled, the corresponding
accessing register should be disabled.
USB Endpoint Accessing Registers Definitions
Rev. 1.10
19
June 29, 2007
HT82A821R
DAC_Limit_L and DAC_Limit_H are used to define the 16-bit DAC output limit. DAC_Limit_L and DAC_Limit_H are unsigned value. If the 16-bit data from Host over the range defined by DAC_Limit_L and DAC_Limit_H, the output digital
code to DAC will be clamp.
DAC_Limit_L
DAC output limit low byte
DAC_Limit_H
DAC output limit high byte
Setting DAC output limit value example:
;----------------------------------------------------------; DAC Limit POR Value=8000H
; Set DAC Limit Value=FF00H
;----------------------------------------------------------clr
[02DH]
; Set DAC Limit low byte=00H
set
[02EH]
; Set DAC Limit high byte=FFH
;----------------------------------------------------------In order to prevent the pop noise of speaker output, power amplifier should be output at the value of VDD/2 (send
8000H to DAC) during the initial power on state. If software set high then clear the bit DAC_WR_TRIG (bit 3 of
DAC_WR register), the value on the DAC_Limit_L and DAC_Limit_H registers will write to DAC.
Bit No.
Label
R/W
Power-on
0~2, 4~7
¾
R
0
Undefined bit, read as ²0².
Functions
3
DAC_WR_TRIG
R/W
0
DAC write trigger bit
DAC_WR (2FH) Register
Example to avoid popping noise:
System_Initial:
;----------------------------------------------------------; Avoid Pop Noise
;----------------------------------------------------------mov
a,WDTS
mov
FIFO_TEMP,a
mov
a,01010000b
andm
a,WDTS
mov
a,01010000b
orm
a,WDTS
;Enter DAC Write Data mode, high nibble of WDTS=0101b
clr
[02DH]
;Set DAC data low byte=00H
mov
a,80H
mov
[02EH],a
;Save WDTS value
;Set DAC data high byte=80H
nop
;Write 8000H to DAC
set
[02FH].3
nop
clr
[02FH].3
nop
;----------------------------------------------------------mov
a,FIFO_TEMP
;Restore WDTS value
mov
WDTS,a
;Quit DAC Write Data mode
;----------------------------------------------------------Note: At DAC write data mode (high nibble of WDTS register is 0101b), DAC_Limit_L and DAC_Limit_H registers will
be the 16-bit DAC input data register at falling edge of DAC_WR_TRIG. Otherwise, these two registers are
used to define the 16-bit DAC output limit.
Rev. 1.10
20
June 29, 2007
HT82A821R
Configuration Options
The following table shows all kinds of OTP option in the microcontroller. All of the OTP options must be defined to ensure proper system functioning.
No.
Options
1
PA0~PA7 pull-high resistor enabled or disabled (by bit)
2
LVR enable or disable
3
WDT enable or disable
4
WDT clock source: fSYS/4 or WDTOSC
5
CLRWDT instruction(s): 1 or 2
6
PA0~PA7 wake-up enabled or disabled (by bit)
7
TBHP enable or disable (default disable)
Application Circuits
J 1
U S B -B T y p e
1
D V D D
2
D 3
D +
4
V S S
1
5
A V D D
3 3 W
1 0 m F
0 .1 m F
1 .5 k W
3 3 W
3 3 W
F B 1
B e a d
D V D D
0 .1 m F
V 3 3 O
1
P A 2
2
P A 1
3
P A 0
4
A V D D 2
5
R O U T
6
2
L O U T
7
B e a d F e r r ite
1
2
A V S S 2
8
U S B D N
4 7 p F
1 0 m F
4 7 p F
2
1
B e a d F e r r ite
1 0 m F
F B 2
1
A V D D
2
A V S S 1
9
B IA S
1 0
A V D D 1
1 1
D V S S 2
1 2
0 .1 m F
1
B e a d F e r r ite
2
A V D D 2
0 .1 m F
1 0 m F
P A 5
P A 1
P A 6
P A 0
P A 7
A V D D 2
D V S S 1
R O U T
V 3 3 O
L O U T
U S B D P
A V S S 2
U S B D N
A V S S 1
D V D D 1
B IA S
R E S E T
O S C O
D V S S 2
O S C I
2 4
2 3
P A 4
P A 5
2 2
P A 6
2 1
P A 7
2 0
D V S S 1
1 9
V 3 3 O
1 8
U S B D P
1 7
U S B D N
1 6
D V D D 1
1 5
R E S E T
1 4
O S C O
O S C I
1 3
1 0 0 k W
0 .1 m F
D V D D
S W 1
R e s e t
1 2 M H z
S W 2
J 5
S W 3
P A 1
P h o n e ja c k S te r e o 1
S W 5
P A 3
1
1
S W 6
1 0 0 m F
3
2
S W 4
P A 2
P A 4
Rev. 1.10
P A 4
P A 2
H T 8 2 A 8 2 1 R
1 0 m F
P A 0
A V D D
P A 3
A V D D 1
A V D D 1
B e a d F e r r ite
L 3
U 1
P A 3
U S B D P
2
1 0 0 m F
L O U T
R O U T
A V S S 2
2
21
June 29, 2007
HT82A821R
Instruction Set
subtract instruction mnemonics to enable the necessary
arithmetic to be carried out. Care must be taken to ensure correct handling of carry and borrow data when results exceed 255 for addition and less than 0 for
subtraction. The increment and decrement instructions
INC, INCA, DEC and DECA provide a simple means of
increasing or decreasing by a value of one of the values
in the destination specified.
Introduction
Central to the successful operation of any
microcontroller is its instruction set, which is a set of program instruction codes that directs the microcontroller to
perform certain operations. In the case of Holtek
microcontrollers, a comprehensive and flexible set of
over 60 instructions is provided to enable programmers
to implement their application with the minimum of programming overheads.
Logical and Rotate Operations
For easier understanding of the various instruction
codes, they have been subdivided into several functional groupings.
The standard logical operations such as AND, OR, XOR
and CPL all have their own instruction within the Holtek
microcontroller instruction set. As with the case of most
instructions involving data manipulation, data must pass
through the Accumulator which may involve additional
programming steps. In all logical data operations, the
zero flag may be set if the result of the operation is zero.
Another form of logical data manipulation comes from
the rotate instructions such as RR, RL, RRC and RLC
which provide a simple means of rotating one bit right or
left. Different rotate instructions exist depending on program requirements. Rotate instructions are useful for
serial port programming applications where data can be
rotated from an internal register into the Carry bit from
where it can be examined and the necessary serial bit
set high or low. Another application where rotate data
operations are used is to implement multiplication and
division calculations.
Instruction Timing
Most instructions are implemented within one instruction cycle. The exceptions to this are branch, call, or table read instructions where two instruction cycles are
required. One instruction cycle is equal to 4 system
clock cycles, therefore in the case of an 8MHz system
oscillator, most instructions would be implemented
within 0.5ms and branch or call instructions would be implemented within 1ms. Although instructions which require one more cycle to implement are generally limited
to the JMP, CALL, RET, RETI and table read instructions, it is important to realize that any other instructions
which involve manipulation of the Program Counter Low
register or PCL will also take one more cycle to implement. As instructions which change the contents of the
PCL will imply a direct jump to that new address, one
more cycle will be required. Examples of such instructions would be ²CLR PCL² or ²MOV PCL, A². For the
case of skip instructions, it must be noted that if the result of the comparison involves a skip operation then
this will also take one more cycle, if no skip is involved
then only one cycle is required.
Branches and Control Transfer
Program branching takes the form of either jumps to
specified locations using the JMP instruction or to a subroutine using the CALL instruction. They differ in the
sense that in the case of a subroutine call, the program
must return to the instruction immediately when the subroutine has been carried out. This is done by placing a
return instruction RET in the subroutine which will cause
the program to jump back to the address right after the
CALL instruction. In the case of a JMP instruction, the
program simply jumps to the desired location. There is
no requirement to jump back to the original jumping off
point as in the case of the CALL instruction. One special
and extremely useful set of branch instructions are the
conditional branches. Here a decision is first made regarding the condition of a certain data memory or individual bits. Depending upon the conditions, the program
will continue with the next instruction or skip over it and
jump to the following instruction. These instructions are
the key to decision making and branching within the program perhaps determined by the condition of certain input switches or by the condition of internal data bits.
Moving and Transferring Data
The transfer of data within the microcontroller program
is one of the most frequently used operations. Making
use of three kinds of MOV instructions, data can be
transferred from registers to the Accumulator and
vice-versa as well as being able to move specific immediate data directly into the Accumulator. One of the most
important data transfer applications is to receive data
from the input ports and transfer data to the output ports.
Arithmetic Operations
The ability to perform certain arithmetic operations and
data manipulation is a necessary feature of most
microcontroller applications. Within the Holtek
microcontroller instruction set are a range of add and
Rev. 1.10
22
June 29, 2007
HT82A821R
Bit Operations
Other Operations
The ability to provide single bit operations on Data Memory is an extremely flexible feature of all Holtek
microcontrollers. This feature is especially useful for
output port bit programming where individual bits or port
pins can be directly set high or low using either the ²SET
[m].i² or ²CLR [m].i² instructions respectively. The feature removes the need for programmers to first read the
8-bit output port, manipulate the input data to ensure
that other bits are not changed and then output the port
with the correct new data. This read-modify-write process is taken care of automatically when these bit operation instructions are used.
In addition to the above functional instructions, a range
of other instructions also exist such as the ²HALT² instruction for Power-down operations and instructions to
control the operation of the Watchdog Timer for reliable
program operations under extreme electric or electromagnetic environments. For their relevant operations,
refer to the functional related sections.
Instruction Set Summary
The following table depicts a summary of the instruction
set categorised according to function and can be consulted as a basic instruction reference using the following listed conventions.
Table Read Operations
Table conventions:
Data storage is normally implemented by using registers. However, when working with large amounts of
fixed data, the volume involved often makes it inconvenient to store the fixed data in the Data Memory. To overcome this problem, Holtek microcontrollers allow an
area of Program Memory to be setup as a table where
data can be directly stored. A set of easy to use instructions provides the means by which this fixed data can be
referenced and retrieved from the Program Memory.
Mnemonic
x: Bits immediate data
m: Data Memory address
A: Accumulator
i: 0~7 number of bits
addr: Program memory address
Description
Cycles
Flag Affected
1
1Note
1
1
1Note
1
1
1Note
1
1Note
1Note
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
C
1
1
1
1Note
1Note
1Note
1
1
1
1Note
1
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
1
1Note
1
1Note
Z
Z
Z
Z
Arithmetic
ADD A,[m]
ADDM A,[m]
ADD A,x
ADC A,[m]
ADCM A,[m]
SUB A,x
SUB A,[m]
SUBM A,[m]
SBC A,[m]
SBCM A,[m]
DAA [m]
Add Data Memory to ACC
Add ACC to Data Memory
Add immediate data to ACC
Add Data Memory to ACC with Carry
Add ACC to Data memory with Carry
Subtract immediate data from the ACC
Subtract Data Memory from ACC
Subtract Data Memory from ACC with result in Data Memory
Subtract Data Memory from ACC with Carry
Subtract Data Memory from ACC with Carry, result in Data Memory
Decimal adjust ACC for Addition with result in Data Memory
Logic Operation
AND A,[m]
OR A,[m]
XOR A,[m]
ANDM A,[m]
ORM A,[m]
XORM A,[m]
AND A,x
OR A,x
XOR A,x
CPL [m]
CPLA [m]
Logical AND Data Memory to ACC
Logical OR Data Memory to ACC
Logical XOR Data Memory to ACC
Logical AND ACC to Data Memory
Logical OR ACC to Data Memory
Logical XOR ACC to Data Memory
Logical AND immediate Data to ACC
Logical OR immediate Data to ACC
Logical XOR immediate Data to ACC
Complement Data Memory
Complement Data Memory with result in ACC
Increment & Decrement
INCA [m]
INC [m]
DECA [m]
DEC [m]
Rev. 1.10
Increment Data Memory with result in ACC
Increment Data Memory
Decrement Data Memory with result in ACC
Decrement Data Memory
23
June 29, 2007
HT82A821R
Mnemonic
Description
Cycles
Flag Affected
Rotate Data Memory right with result in ACC
Rotate Data Memory right
Rotate Data Memory right through Carry with result in ACC
Rotate Data Memory right through Carry
Rotate Data Memory left with result in ACC
Rotate Data Memory left
Rotate Data Memory left through Carry with result in ACC
Rotate Data Memory left through Carry
1
1Note
1
1Note
1
1Note
1
1Note
None
None
C
C
None
None
C
C
Move Data Memory to ACC
Move ACC to Data Memory
Move immediate data to ACC
1
1Note
1
None
None
None
Clear bit of Data Memory
Set bit of Data Memory
1Note
1Note
None
None
Jump unconditionally
Skip if Data Memory is zero
Skip if Data Memory is zero with data movement to ACC
Skip if bit i of Data Memory is zero
Skip if bit i of Data Memory is not zero
Skip if increment Data Memory is zero
Skip if decrement Data Memory is zero
Skip if increment Data Memory is zero with result in ACC
Skip if decrement Data Memory is zero with result in ACC
Subroutine call
Return from subroutine
Return from subroutine and load immediate data to ACC
Return from interrupt
2
1Note
1note
1Note
1Note
1Note
1Note
1Note
1Note
2
2
2
2
None
None
None
None
None
None
None
None
None
None
None
None
None
Read table (current page) to TBLH and Data Memory
Read table (last page) to TBLH and Data Memory
2Note
2Note
None
None
No operation
Clear Data Memory
Set Data Memory
Clear Watchdog Timer
Pre-clear Watchdog Timer
Pre-clear Watchdog Timer
Swap nibbles of Data Memory
Swap nibbles of Data Memory with result in ACC
Enter power down mode
1
1Note
1Note
1
1
1
1Note
1
1
None
None
None
TO, PDF
TO, PDF
TO, PDF
None
None
TO, PDF
Rotate
RRA [m]
RR [m]
RRCA [m]
RRC [m]
RLA [m]
RL [m]
RLCA [m]
RLC [m]
Data Move
MOV A,[m]
MOV [m],A
MOV A,x
Bit Operation
CLR [m].i
SET [m].i
Branch
JMP addr
SZ [m]
SZA [m]
SZ [m].i
SNZ [m].i
SIZ [m]
SDZ [m]
SIZA [m]
SDZA [m]
CALL addr
RET
RET A,x
RETI
Table Read
TABRDC [m]
TABRDL [m]
Miscellaneous
NOP
CLR [m]
SET [m]
CLR WDT
CLR WDT1
CLR WDT2
SWAP [m]
SWAPA [m]
HALT
Note: 1. For skip instructions, if the result of the comparison involves a skip then two cycles are required,
if no skip takes place only one cycle is required.
2. Any instruction which changes the contents of the PCL will also require 2 cycles for execution.
3. For the ²CLR WDT1² and ²CLR WDT2² instructions the TO and PDF flags may be affected by
the execution status. The TO and PDF flags are cleared after both ²CLR WDT1² and
²CLR WDT2² instructions are consecutively executed. Otherwise the TO and PDF flags
remain unchanged.
Rev. 1.10
24
June 29, 2007
HT82A821R
Instruction Definition
ADC A,[m]
Add Data Memory to ACC with Carry
Description
The contents of the specified Data Memory, Accumulator and the carry flag are added. The
result is stored in the Accumulator.
Operation
ACC ¬ ACC + [m] + C
Affected flag(s)
OV, Z, AC, C
ADCM A,[m]
Add ACC to Data Memory with Carry
Description
The contents of the specified Data Memory, Accumulator and the carry flag are added. The
result is stored in the specified Data Memory.
Operation
[m] ¬ ACC + [m] + C
Affected flag(s)
OV, Z, AC, C
ADD A,[m]
Add Data Memory to ACC
Description
The contents of the specified Data Memory and the Accumulator are added. The result is
stored in the Accumulator.
Operation
ACC ¬ ACC + [m]
Affected flag(s)
OV, Z, AC, C
ADD A,x
Add immediate data to ACC
Description
The contents of the Accumulator and the specified immediate data are added. The result is
stored in the Accumulator.
Operation
ACC ¬ ACC + x
Affected flag(s)
OV, Z, AC, C
ADDM A,[m]
Add ACC to Data Memory
Description
The contents of the specified Data Memory and the Accumulator are added. The result is
stored in the specified Data Memory.
Operation
[m] ¬ ACC + [m]
Affected flag(s)
OV, Z, AC, C
AND A,[m]
Logical AND Data Memory to ACC
Description
Data in the Accumulator and the specified Data Memory perform a bitwise logical AND operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²AND² [m]
Affected flag(s)
Z
AND A,x
Logical AND immediate data to ACC
Description
Data in the Accumulator and the specified immediate data perform a bitwise logical AND
operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²AND² x
Affected flag(s)
Z
ANDM A,[m]
Logical AND ACC to Data Memory
Description
Data in the specified Data Memory and the Accumulator perform a bitwise logical AND operation. The result is stored in the Data Memory.
Operation
[m] ¬ ACC ²AND² [m]
Affected flag(s)
Z
Rev. 1.10
25
June 29, 2007
HT82A821R
CALL addr
Subroutine call
Description
Unconditionally calls a subroutine at the specified address. The Program Counter then increments by 1 to obtain the address of the next instruction which is then pushed onto the
stack. The specified address is then loaded and the program continues execution from this
new address. As this instruction requires an additional operation, it is a two cycle instruction.
Operation
Stack ¬ Program Counter + 1
Program Counter ¬ addr
Affected flag(s)
None
CLR [m]
Clear Data Memory
Description
Each bit of the specified Data Memory is cleared to 0.
Operation
[m] ¬ 00H
Affected flag(s)
None
CLR [m].i
Clear bit of Data Memory
Description
Bit i of the specified Data Memory is cleared to 0.
Operation
[m].i ¬ 0
Affected flag(s)
None
CLR WDT
Clear Watchdog Timer
Description
The TO, PDF flags and the WDT are all cleared.
Operation
WDT cleared
TO ¬ 0
PDF ¬ 0
Affected flag(s)
TO, PDF
CLR WDT1
Pre-clear Watchdog Timer
Description
The TO, PDF flags and the WDT are all cleared. Note that this instruction works in conjunction with CLR WDT2 and must be executed alternately with CLR WDT2 to have effect. Repetitively executing this instruction without alternately executing CLR WDT2 will have no
effect.
Operation
WDT cleared
TO ¬ 0
PDF ¬ 0
Affected flag(s)
TO, PDF
CLR WDT2
Pre-clear Watchdog Timer
Description
The TO, PDF flags and the WDT are all cleared. Note that this instruction works in conjunction with CLR WDT1 and must be executed alternately with CLR WDT1 to have effect. Repetitively executing this instruction without alternately executing CLR WDT1 will have no
effect.
Operation
WDT cleared
TO ¬ 0
PDF ¬ 0
Affected flag(s)
TO, PDF
Rev. 1.10
26
June 29, 2007
HT82A821R
CPL [m]
Complement Data Memory
Description
Each bit of the specified Data Memory is logically complemented (1¢s complement). Bits
which previously contained a 1 are changed to 0 and vice versa.
Operation
[m] ¬ [m]
Affected flag(s)
Z
CPLA [m]
Complement Data Memory with result in ACC
Description
Each bit of the specified Data Memory is logically complemented (1¢s complement). Bits
which previously contained a 1 are changed to 0 and vice versa. The complemented result
is stored in the Accumulator and the contents of the Data Memory remain unchanged.
Operation
ACC ¬ [m]
Affected flag(s)
Z
DAA [m]
Decimal-Adjust ACC for addition with result in Data Memory
Description
Convert the contents of the Accumulator value to a BCD ( Binary Coded Decimal) value resulting from the previous addition of two BCD variables. If the low nibble is greater than 9 or
if AC flag is set, then a value of 6 will be added to the low nibble. Otherwise the low nibble
remains unchanged. If the high nibble is greater than 9 or if the C flag is set, then a value of
6 will be added to the high nibble. Essentially, the decimal conversion is performed by adding 00H, 06H, 60H or 66H depending on the Accumulator and flag conditions. Only the C
flag may be affected by this instruction which indicates that if the original BCD sum is
greater than 100, it allows multiple precision decimal addition.
Operation
[m] ¬ ACC + 00H or
[m] ¬ ACC + 06H or
[m] ¬ ACC + 60H or
[m] ¬ ACC + 66H
Affected flag(s)
C
DEC [m]
Decrement Data Memory
Description
Data in the specified Data Memory is decremented by 1.
Operation
[m] ¬ [m] - 1
Affected flag(s)
Z
DECA [m]
Decrement Data Memory with result in ACC
Description
Data in the specified Data Memory is decremented by 1. The result is stored in the Accumulator. The contents of the Data Memory remain unchanged.
Operation
ACC ¬ [m] - 1
Affected flag(s)
Z
HALT
Enter power down mode
Description
This instruction stops the program execution and turns off the system clock. The contents
of the Data Memory and registers are retained. The WDT and prescaler are cleared. The
power down flag PDF is set and the WDT time-out flag TO is cleared.
Operation
TO ¬ 0
PDF ¬ 1
Affected flag(s)
TO, PDF
Rev. 1.10
27
June 29, 2007
HT82A821R
INC [m]
Increment Data Memory
Description
Data in the specified Data Memory is incremented by 1.
Operation
[m] ¬ [m] + 1
Affected flag(s)
Z
INCA [m]
Increment Data Memory with result in ACC
Description
Data in the specified Data Memory is incremented by 1. The result is stored in the Accumulator. The contents of the Data Memory remain unchanged.
Operation
ACC ¬ [m] + 1
Affected flag(s)
Z
JMP addr
Jump unconditionally
Description
The contents of the Program Counter are replaced with the specified address. Program
execution then continues from this new address. As this requires the insertion of a dummy
instruction while the new address is loaded, it is a two cycle instruction.
Operation
Program Counter ¬ addr
Affected flag(s)
None
MOV A,[m]
Move Data Memory to ACC
Description
The contents of the specified Data Memory are copied to the Accumulator.
Operation
ACC ¬ [m]
Affected flag(s)
None
MOV A,x
Move immediate data to ACC
Description
The immediate data specified is loaded into the Accumulator.
Operation
ACC ¬ x
Affected flag(s)
None
MOV [m],A
Move ACC to Data Memory
Description
The contents of the Accumulator are copied to the specified Data Memory.
Operation
[m] ¬ ACC
Affected flag(s)
None
NOP
No operation
Description
No operation is performed. Execution continues with the next instruction.
Operation
No operation
Affected flag(s)
None
OR A,[m]
Logical OR Data Memory to ACC
Description
Data in the Accumulator and the specified Data Memory perform a bitwise logical OR operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²OR² [m]
Affected flag(s)
Z
Rev. 1.10
28
June 29, 2007
HT82A821R
OR A,x
Logical OR immediate data to ACC
Description
Data in the Accumulator and the specified immediate data perform a bitwise logical OR operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²OR² x
Affected flag(s)
Z
ORM A,[m]
Logical OR ACC to Data Memory
Description
Data in the specified Data Memory and the Accumulator perform a bitwise logical OR operation. The result is stored in the Data Memory.
Operation
[m] ¬ ACC ²OR² [m]
Affected flag(s)
Z
RET
Return from subroutine
Description
The Program Counter is restored from the stack. Program execution continues at the restored address.
Operation
Program Counter ¬ Stack
Affected flag(s)
None
RET A,x
Return from subroutine and load immediate data to ACC
Description
The Program Counter is restored from the stack and the Accumulator loaded with the
specified immediate data. Program execution continues at the restored address.
Operation
Program Counter ¬ Stack
ACC ¬ x
Affected flag(s)
None
RETI
Return from interrupt
Description
The Program Counter is restored from the stack and the interrupts are re-enabled by setting the EMI bit. EMI is the enable master (global) interrupt bit (bit 0; register INTC). If an interrupt was pending when the RETI instruction is executed, the pending Interrupt routine
will be processed before returning to the main program.
Operation
Program Counter ¬ Stack
EMI ¬ 1
Affected flag(s)
None
RL [m]
Rotate Data Memory left
Description
The contents of the specified Data Memory are rotated left by 1 bit with bit 7 rotated into bit
0.
Operation
[m].(i+1) ¬ [m].i; (i = 0~6)
[m].0 ¬ [m].7
Affected flag(s)
None
RLA [m]
Rotate Data Memory left with result in ACC
Description
The contents of the specified Data Memory are rotated left by 1 bit with bit 7 rotated into bit
0. The rotated result is stored in the Accumulator and the contents of the Data Memory remain unchanged.
Operation
ACC.(i+1) ¬ [m].i; (i = 0~6)
ACC.0 ¬ [m].7
Affected flag(s)
None
Rev. 1.10
29
June 29, 2007
HT82A821R
RLC [m]
Rotate Data Memory left through Carry
Description
The contents of the specified Data Memory and the carry flag are rotated left by 1 bit. Bit 7
replaces the Carry bit and the original carry flag is rotated into bit 0.
Operation
[m].(i+1) ¬ [m].i; (i = 0~6)
[m].0 ¬ C
C ¬ [m].7
Affected flag(s)
C
RLCA [m]
Rotate Data Memory left through Carry with result in ACC
Description
Data in the specified Data Memory and the carry flag are rotated left by 1 bit. Bit 7 replaces
the Carry bit and the original carry flag is rotated into the bit 0. The rotated result is stored in
the Accumulator and the contents of the Data Memory remain unchanged.
Operation
ACC.(i+1) ¬ [m].i; (i = 0~6)
ACC.0 ¬ C
C ¬ [m].7
Affected flag(s)
C
RR [m]
Rotate Data Memory right
Description
The contents of the specified Data Memory are rotated right by 1 bit with bit 0 rotated into
bit 7.
Operation
[m].i ¬ [m].(i+1); (i = 0~6)
[m].7 ¬ [m].0
Affected flag(s)
None
RRA [m]
Rotate Data Memory right with result in ACC
Description
Data in the specified Data Memory and the carry flag are rotated right by 1 bit with bit 0 rotated into bit 7. The rotated result is stored in the Accumulator and the contents of the Data
Memory remain unchanged.
Operation
ACC.i ¬ [m].(i+1); (i = 0~6)
ACC.7 ¬ [m].0
Affected flag(s)
None
RRC [m]
Rotate Data Memory right through Carry
Description
The contents of the specified Data Memory and the carry flag are rotated right by 1 bit. Bit 0
replaces the Carry bit and the original carry flag is rotated into bit 7.
Operation
[m].i ¬ [m].(i+1); (i = 0~6)
[m].7 ¬ C
C ¬ [m].0
Affected flag(s)
C
RRCA [m]
Rotate Data Memory right through Carry with result in ACC
Description
Data in the specified Data Memory and the carry flag are rotated right by 1 bit. Bit 0 replaces the Carry bit and the original carry flag is rotated into bit 7. The rotated result is
stored in the Accumulator and the contents of the Data Memory remain unchanged.
Operation
ACC.i ¬ [m].(i+1); (i = 0~6)
ACC.7 ¬ C
C ¬ [m].0
Affected flag(s)
C
Rev. 1.10
30
June 29, 2007
HT82A821R
SBC A,[m]
Subtract Data Memory from ACC with Carry
Description
The contents of the specified Data Memory and the complement of the carry flag are subtracted from the Accumulator. The result is stored in the Accumulator. Note that if the result
of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is positive or
zero, the C flag will be set to 1.
Operation
ACC ¬ ACC - [m] - C
Affected flag(s)
OV, Z, AC, C
SBCM A,[m]
Subtract Data Memory from ACC with Carry and result in Data Memory
Description
The contents of the specified Data Memory and the complement of the carry flag are subtracted from the Accumulator. The result is stored in the Data Memory. Note that if the result of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is
positive or zero, the C flag will be set to 1.
Operation
[m] ¬ ACC - [m] - C
Affected flag(s)
OV, Z, AC, C
SDZ [m]
Skip if decrement Data Memory is 0
Description
The contents of the specified Data Memory are first decremented by 1. If the result is 0 the
following instruction is skipped. As this requires the insertion of a dummy instruction while
the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the program
proceeds with the following instruction.
Operation
[m] ¬ [m] - 1
Skip if [m] = 0
Affected flag(s)
None
SDZA [m]
Skip if decrement Data Memory is zero with result in ACC
Description
The contents of the specified Data Memory are first decremented by 1. If the result is 0, the
following instruction is skipped. The result is stored in the Accumulator but the specified
Data Memory contents remain unchanged. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not
0, the program proceeds with the following instruction.
Operation
ACC ¬ [m] - 1
Skip if ACC = 0
Affected flag(s)
None
SET [m]
Set Data Memory
Description
Each bit of the specified Data Memory is set to 1.
Operation
[m] ¬ FFH
Affected flag(s)
None
SET [m].i
Set bit of Data Memory
Description
Bit i of the specified Data Memory is set to 1.
Operation
[m].i ¬ 1
Affected flag(s)
None
Rev. 1.10
31
June 29, 2007
HT82A821R
SIZ [m]
Skip if increment Data Memory is 0
Description
The contents of the specified Data Memory are first incremented by 1. If the result is 0, the
following instruction is skipped. As this requires the insertion of a dummy instruction while
the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the program
proceeds with the following instruction.
Operation
[m] ¬ [m] + 1
Skip if [m] = 0
Affected flag(s)
None
SIZA [m]
Skip if increment Data Memory is zero with result in ACC
Description
The contents of the specified Data Memory are first incremented by 1. If the result is 0, the
following instruction is skipped. The result is stored in the Accumulator but the specified
Data Memory contents remain unchanged. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not
0 the program proceeds with the following instruction.
Operation
ACC ¬ [m] + 1
Skip if ACC = 0
Affected flag(s)
None
SNZ [m].i
Skip if bit i of Data Memory is not 0
Description
If bit i of the specified Data Memory is not 0, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two
cycle instruction. If the result is 0 the program proceeds with the following instruction.
Operation
Skip if [m].i ¹ 0
Affected flag(s)
None
SUB A,[m]
Subtract Data Memory from ACC
Description
The specified Data Memory is subtracted from the contents of the Accumulator. The result
is stored in the Accumulator. Note that if the result of subtraction is negative, the C flag will
be cleared to 0, otherwise if the result is positive or zero, the C flag will be set to 1.
Operation
ACC ¬ ACC - [m]
Affected flag(s)
OV, Z, AC, C
SUBM A,[m]
Subtract Data Memory from ACC with result in Data Memory
Description
The specified Data Memory is subtracted from the contents of the Accumulator. The result
is stored in the Data Memory. Note that if the result of subtraction is negative, the C flag will
be cleared to 0, otherwise if the result is positive or zero, the C flag will be set to 1.
Operation
[m] ¬ ACC - [m]
Affected flag(s)
OV, Z, AC, C
SUB A,x
Subtract immediate data from ACC
Description
The immediate data specified by the code is subtracted from the contents of the Accumulator. The result is stored in the Accumulator. Note that if the result of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is positive or zero, the C flag will
be set to 1.
Operation
ACC ¬ ACC - x
Affected flag(s)
OV, Z, AC, C
Rev. 1.10
32
June 29, 2007
HT82A821R
SWAP [m]
Swap nibbles of Data Memory
Description
The low-order and high-order nibbles of the specified Data Memory are interchanged.
Operation
[m].3~[m].0 « [m].7 ~ [m].4
Affected flag(s)
None
SWAPA [m]
Swap nibbles of Data Memory with result in ACC
Description
The low-order and high-order nibbles of the specified Data Memory are interchanged. The
result is stored in the Accumulator. The contents of the Data Memory remain unchanged.
Operation
ACC.3 ~ ACC.0 ¬ [m].7 ~ [m].4
ACC.7 ~ ACC.4 ¬ [m].3 ~ [m].0
Affected flag(s)
None
SZ [m]
Skip if Data Memory is 0
Description
If the contents of the specified Data Memory is 0, the following instruction is skipped. As
this requires the insertion of a dummy instruction while the next instruction is fetched, it is a
two cycle instruction. If the result is not 0 the program proceeds with the following instruction.
Operation
Skip if [m] = 0
Affected flag(s)
None
SZA [m]
Skip if Data Memory is 0 with data movement to ACC
Description
The contents of the specified Data Memory are copied to the Accumulator. If the value is
zero, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the
program proceeds with the following instruction.
Operation
ACC ¬ [m]
Skip if [m] = 0
Affected flag(s)
None
SZ [m].i
Skip if bit i of Data Memory is 0
Description
If bit i of the specified Data Memory is 0, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two
cycle instruction. If the result is not 0, the program proceeds with the following instruction.
Operation
Skip if [m].i = 0
Affected flag(s)
None
TABRDC [m]
Read table (current page) to TBLH and Data Memory
Description
The low byte of the program code (current page) addressed by the table pointer (TBLP) is
moved to the specified Data Memory and the high byte moved to TBLH.
Operation
[m] ¬ program code (low byte)
TBLH ¬ program code (high byte)
Affected flag(s)
None
TABRDL [m]
Read table (last page) to TBLH and Data Memory
Description
The low byte of the program code (last page) addressed by the table pointer (TBLP) is
moved to the specified Data Memory and the high byte moved to TBLH.
Operation
[m] ¬ program code (low byte)
TBLH ¬ program code (high byte)
Affected flag(s)
None
Rev. 1.10
33
June 29, 2007
HT82A821R
XOR A,[m]
Logical XOR Data Memory to ACC
Description
Data in the Accumulator and the specified Data Memory perform a bitwise logical XOR operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²XOR² [m]
Affected flag(s)
Z
XORM A,[m]
Logical XOR ACC to Data Memory
Description
Data in the specified Data Memory and the Accumulator perform a bitwise logical XOR operation. The result is stored in the Data Memory.
Operation
[m] ¬ ACC ²XOR² [m]
Affected flag(s)
Z
XOR A,x
Logical XOR immediate data to ACC
Description
Data in the Accumulator and the specified immediate data perform a bitwise logical XOR
operation. The result is stored in the Accumulator.
Operation
ACC ¬ ACC ²XOR² x
Affected flag(s)
Z
Rev. 1.10
34
June 29, 2007
HT82A821R
Package Information
24-pin SSOP (150mil) Outline Dimensions
1 3
2 4
A
B
1 2
1
C
C '
G
H
D
E
Symbol
Rev. 1.10
a
F
Dimensions in mil
Min.
Nom.
Max.
A
228
¾
244
B
150
¾
157
C
8
¾
12
C¢
335
¾
346
D
54
¾
60
E
¾
25
¾
F
4
¾
10
G
22
¾
28
H
7
¾
10
a
0°
¾
8°
35
June 29, 2007
HT82A821R
24-pin SOP (300mil) Outline Dimensions
1 3
2 4
A
B
1 2
1
C
C '
G
H
D
E
Symbol
Rev. 1.10
a
F
Dimensions in mil
Min.
Nom.
Max.
A
394
¾
419
B
290
¾
300
C
14
¾
20
C¢
590
¾
614
D
92
¾
104
E
¾
50
¾
F
4
¾
¾
G
32
¾
38
H
4
¾
12
a
0°
¾
10°
36
June 29, 2007
HT82A821R
Product Tape and Reel Specifications
Reel Dimensions
D
T 2
A
C
B
T 1
SSOP 24S (150mil)
Symbol
Description
Dimensions in mm
A
Reel Outer Diameter
B
Reel Inner Diameter
62±1.5
C
Spindle Hole Diameter
13+0.5
-0.2
D
Key Slit Width
330±1
2±0.5
T1
Space Between Flange
16.8+0.3
-0.2
T2
Reel Thickness
22.2±0.2
SOP 24W
Symbol
Description
Dimensions in mm
A
Reel Outer Diameter
330±1
B
Reel Inner Diameter
62±1.5
C
Spindle Hole Diameter
13+0.5
-0.2
D
Key Slit Width
2±0.5
T1
Space Between Flange
24.8+0.3
-0.2
T2
Reel Thickness
30.2±0.2
Rev. 1.10
37
June 29, 2007
HT82A821R
Carrier Tape Dimensions
P 0
D
P 1
t
E
F
W
C
D 1
B 0
P
K 0
A 0
SSOP 24S (150mil)
Symbol
Description
Dimensions in mm
W
Carrier Tape Width
16+0.3
-0.1
P
Cavity Pitch
8±0.1
E
Perforation Position
F
Cavity to Perforation (Width Direction)
7.5±0.1
D
Perforation Diameter
1.5+0.1
D1
Cavity Hole Diameter
1.5+0.25
P0
Perforation Pitch
1.75±0.1
4±0.1
P1
Cavity to Perforation (Length Direction)
A0
Cavity Length
6.5±0.1
B0
Cavity Width
9.5±0.1
K0
Cavity Depth
2.1±0.1
t
Carrier Tape Thickness
0.3±0.05
C
Cover Tape Width
2±0.1
13.3
SOP 24W
Symbol
Description
Dimensions in mm
W
Carrier Tape Width
24±0.3
P
Cavity Pitch
12±0.1
E
Perforation Position
1.75±0.1
F
Cavity to Perforation (Width Direction)
11.5±0.1
D
Perforation Diameter
1.55+0.1
D1
Cavity Hole Diameter
1.5+0.25
P0
Perforation Pitch
4±0.1
P1
Cavity to Perforation (Length Direction)
2±0.1
A0
Cavity Length
10.9±0.1
B0
Cavity Width
15.9±0.1
K0
Cavity Depth
t
Carrier Tape Thickness
C
Cover Tape Width
Rev. 1.10
3.1±0.1
0.35±0.05
21.3
38
June 29, 2007
HT82A821R
Holtek Semiconductor Inc. (Headquarters)
No.3, Creation Rd. II, Science Park, Hsinchu, Taiwan
Tel: 886-3-563-1999
Fax: 886-3-563-1189
http://www.holtek.com.tw
Holtek Semiconductor Inc. (Taipei Sales Office)
4F-2, No. 3-2, YuanQu St., Nankang Software Park, Taipei 115, Taiwan
Tel: 886-2-2655-7070
Fax: 886-2-2655-7373
Fax: 886-2-2655-7383 (International sales hotline)
Holtek Semiconductor Inc. (Shanghai Sales Office)
7th Floor, Building 2, No.889, Yi Shan Rd., Shanghai, China 200233
Tel: 86-21-6485-5560
Fax: 86-21-6485-0313
http://www.holtek.com.cn
Holtek Semiconductor Inc. (Shenzhen Sales Office)
5/F, Unit A, Productivity Building, Cross of Science M 3rd Road and Gaoxin M 2nd Road, Science Park, Nanshan District,
Shenzhen, China 518057
Tel: 86-755-8616-9908, 86-755-8616-9308
Fax: 86-755-8616-9722
Holtek Semiconductor Inc. (Beijing Sales Office)
Suite 1721, Jinyu Tower, A129 West Xuan Wu Men Street, Xicheng District, Beijing, China 100031
Tel: 86-10-6641-0030, 86-10-6641-7751, 86-10-6641-7752
Fax: 86-10-6641-0125
Holtek Semiconductor Inc. (Chengdu Sales Office)
709, Building 3, Champagne Plaza, No.97 Dongda Street, Chengdu, Sichuan, China 610016
Tel: 86-28-6653-6590
Fax: 86-28-6653-6591
Holtek Semiconductor (USA), Inc. (North America Sales Office)
46729 Fremont Blvd., Fremont, CA 94538
Tel: 1-510-252-9880
Fax: 1-510-252-9885
http://www.holtek.com
Copyright Ó 2007 by HOLTEK SEMICONDUCTOR INC.
The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used
solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable
without further modification, nor recommends the use of its products for application that may present a risk to human life
due to malfunction or otherwise. Holtek¢s products are not authorized for use as critical components in life support devices
or systems. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information,
please visit our web site at http://www.holtek.com.tw.
Rev. 1.10
39
June 29, 2007