3.0mmx1.0mm RIGHT ANGLE SMD CHIP LED LAMP APBA3010SURKSGC HYPER RED SUPER BRIGHT GREEN Features Description 3.0mmx1.0mm RIGHT ANGLE SMT LED, 2.0mm The Hyper Red source color devices are made with DH THICKNESS. InGaAlP on GaAs substrate Light Emitting Diode. LOW POWER CONSUMPTION. The Super Bright Green source color devices are made WIDE VIEWING ANGLE. with Gallium Phosphide Green Light Emitting Diode. IDEAL FOR BACKLIGHT AND INDICATOR. VARIOUS COLRS AND LENS TYPES AVAILABLE. PACKAGE : 2000PCS / REEL. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.15(0.006") unless otherwise noted. 3. Specifications are subject to change without notice. SPEC NO: DSAD1090 REV NO: V.2 DATE: DEC/29/2003 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: S.J.HOU PAGE: 1 OF 5 Selection Guide Part No. Dice Iv (mcd) @ 20mA Lens Type Min. Typ. 110 200 2.6 12 HYPER RED (InGaAlP) APBA3010SURKSGC Viewing Angle WATER CLEAR 2 θ 1/2 140° SUPER BRIGHT GREEN (GaP) Note: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. λpeak Peak Wavelength Hyper Red Super Bright Green λD Dominate Wavelength ∆λ1/2 Max. Units Test Conditions 650 565 nm IF=20mA Hyper Red Super Bright Green 635 568 nm IF=20mA Spectral Line Half-width Hyper Red Super Bright Green 28 30 nm IF=20mA C Capacitance Hyper Red Super Bright Green 35 15 pF VF=0V;f=1MHz VF Forward Voltage Hyper Red Super Bright Green 1.95 2.2 2.5 2.5 V IF=20mA IR Reverse Current All 10 uA VR = 5V Absolute Maximum Ratings at TA=25°C Parameter Hyper Red Super Bright Green Units Power dissipation 170 105 mW DC Forward Current 30 25 mA Peak Forward Current [1] 185 140 mA 5 5 V Reverse Voltage Operating / storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAD1090 REV NO: V.2 DATE: DEC/29/2003 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: S.J.HOU PAGE: 2 OF 5 APBA3010SURKSGC Hyper Red SPEC NO: DSAD1090 REV NO: V.2 DATE: DEC/29/2003 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: S.J.HOU PAGE: 3 OF 5 Super Bright Green SPEC NO: DSAD1090 REV NO: V.2 DATE: DEC/29/2003 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: S.J.HOU PAGE: 4 OF 5 APBA3010SURKSGC SMT Reflow Soldering Instructions Number of reflow process shall be less than 2 times and cooling process to normal temperature is required between first and second soldering process. Recommended Soldering Pattern (Units : mm) Tape Specifications (Units : mm) SPEC NO: DSAD1090 REV NO: V.2 DATE: DEC/29/2003 APPROVED: J. Lu CHECKED: Allen Liu DRAWN: S.J.HOU PAGE: 5 OF 5