Current Transducer HAT 200..1500-S For the electronic measurement of currents: DC, AC, pulsed, mixed, with a galvanic isolation between the primary circuit (high power) and the secondary circuit (electronic circuit). IPN = 200..1500 A VOUT = ± 4 V Electrical data Primary nominal r.m.s. current IPN (A) Primary current measuring range 4) IP (A) 200 400 500 600 750 800 1000 1200 1500 VC IC R IS VOUT ROUT RL ± ± ± ± ± ± ± ± ± 600 1200 1500 1800 2250 2400 3000 3000 3000 Supply voltage (± 5 %) 4) Current consumption Isolation resistance @ 500 VDC Output voltage @ ± IPN, RL = 10 kΩ, TA = 25°C Output internal resistance Load resistance Type HAT HAT HAT HAT HAT HAT HAT HAT HAT Features 200-S 400-S 500-S 600-S 750-S 800-S 1000-S 1200-S 1500-S ± 15 ± 15 > 1000 ±4 100 > 10 • Hall effect measuring principle • Galvanic isolation between primary V mA MΩ V Ω kΩ Accuracy-Dynamic performance data X ε L VOE VOH VOT TCε G tr f Accuracy @ IPN, TA = 25°C (without offset) Linearity error 1) (0 .. ± IPN) Electrical offset voltage, TA = 25°C Hysteresis offset voltage @ IP = 0; after an excursion of 1 x IPN Thermal drift of VOE Thermal drift of the gain (% of reading) Response time @ 90% of IP Frequency bandwidth 2) (- 3 dB) m Notes : and secondary circuit Isolation voltage 3000 V Low power consumption Extended measuring range(3 x IPN) Insulated plastic case recognized according to UL 94-V0 Advantages • Easy mounting • Small size and space saving • Only one design for wide current ratings range < ± 1 % of IPN < ± 1 % of IPN < ± 20 mV • High immunity to external < ± 10 mV <±1 mV/K < ± 0.1 %/K <5 µs DC .. 25 kHz Applications Ambient operating temperature - 10 .. + 80 Ambient storage temperature HAT 200-S, HAT 500..1500-S - 15 .. + 85 HAT 400-S - 25 .. + 85 Mass 300 UL94 classification V0 interference. • DC motor drives • Switched Mode Power Supplies (SMPS) • AC variable speed drives • Uninterruptible Power Supplies General data TA TS • • • • °C °C °C g (UPS) • Battery supplied applications • Power supplies for welding applications 1) Linearity data exclude the electrical offset. Please refer to derating curves in the technical file to avoid excessive core heating at high frequency. 3) Please consult characterisation report for more technical details and application advice. 4) Operating at ±12V ≤ Vc < ±15V will reduce the measuring range. 2) LEM reserves the right to carry out modifications on its transducers, in order to improve them, without previous notice. LEM Industrial 051011/9 Page 1/3 www.lem.com Current Transducer HAT 200..1500-S Isolation characteristics Vd dCp dCl CTI Rated Voltage with IEC 61010-1 standards and following conditions - Reinforced insulation - Over voltage category III - Pollution degree 2 - Heterogeneous field R.m.s. voltage for AC isolation test, 50 Hz, 1 mn Creepage distance Clearance distance Comparative Tracking Index (Group IIIa) 1000 3 > 11 > 11 275 V kV mm mm Notes : 051011/9 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without previous notice. LEM Industrial Page 2/3 www.lem.com Dimensions HAT 200..1500-S (in mm. 1 mm = 0.0394 inch) Top view HAT-S SERIES (unit = mm) = = 46 Max. = 38 = 5 12 24 HAT 500-S to 1500-S 12 29 12 Positive curren currentt flow 65 10 70 30 30.5 x 40.5 10 15.5 1 4 4 Molex 5045-04A 4 6 Pins arrangement 2 3 (-) Output 1 78 1 (+) 90 Front view 4 0V All holes O 4.5mm HAT 200-S Fixation by base-plate or on bus bar Mechanical characteristics • General tolerance • Transducer fastening • Connection of secondary 30.5 x 40.5 ± 1 mm By base-plate or on 432 1 bus bar Molex with5045-04A M4 screws. All slots ∅ 4.5 mm Molex 5045-04A Safety with M4 screws Pins arrangement: 1 2 3 4 (+) (-) Output 0V This transducer must be used in electric/electronic equipment with respect to applicable standards and safety requirements 99/05 in accordance with the following manufacturer's operating instructions. Caution, risk of electrical shock Remarks • IS is positive when IP flows in the direction of the arrow. • Temperature of the primary conductor should not exceed 100°C. When operating the transducer, certain parts of the module can carry hazardous voltage (eg. primary busbar, power supply). Ignoring this warning can lead to injury and/or cause serious damage. This transducer is a built-in device, whose conducting parts must be inaccessible after installation. A protective housing or additional shield could be used. Main supply must be able to be disconnected. 051011/9 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without previous notice. LEM Industrial Page 3/3 www.lem.com