No. STSE-CC6130A <Cat.No.061218> SPECIFICATIONS FOR NICHIA CHIP TYPE UV LED MODEL : NCSU033A(T) NICHIA CORPORATION -0- Nichia STSE-CC6130A <Cat.No.061218> 1.SPECIFICATIONS (1) Absolute Maximum Ratings Item Forward Current Pulse Forward Current Allowable Reverse Current Power Dissipation Operating Temperature Storage Temperature Dice Temperature Symbol IF IFP IR PD Topr Tstg Tj Absolute Maximum Rating 700 1000 85 3.3 -10 ~ + 85 -40 ~ + 100 130 (Ts=25°C) Unit mA mA mA W °C °C °C IFP Conditions : Pulse Width < = 10msec. and Duty < = 1/10 (2) Initial Electrical/Optical Characteristics Item Symbol Rank H VF Forward Voltage Rank M VF Rank L VF Peak Wavelength Rank Ua λP Spectrum Half Width Uλ Rank P7 Po Optical Power Output Rank P6 Po Rank P5 Po Condition IF=500[mA] IF=500[mA] IF=500[mA] IF=500[mA] IF=500[mA] IF=500[mA] IF=500[mA] IF=500[mA] Min. 4.0 3.6 3.2 360 270 230 190 Typ. (365) (9) - Ts : The solder temperature of products (Please refer to the drawing, 061130658591.) Forward Voltage Measurement allowance is ± 3%. Peak Wavelength Measurement allowance is ±3nm. Optical Power Output Measurement allowance is ±10%. 2.INITIAL OPTICAL/ELECTRICAL CHARACTERISTICS Please refer to figure’s page. 3.OUTLINE DIMENSIONS AND MATERIALS Please refer to figure’s page. Material as follows ; Package Glass Electrodes : : : -1- Ceramics Hard Glass Au Plating Max. 4.4 4.0 3.6 370 310 270 230 (Ts=25°C) Unit V V V nm nm mW mW mW Nichia STSE-CC6130A <Cat.No.061218> 4.PACKAGING · The LEDs are packed in cardboard boxes after packaging in moisture proof foil bag. Please refer to figure’s page. The label on the minimum packing unit shows ; Part Number, Lot Number, Ranking, Quantity (Taped Type) · The LEDs are packed in cardboard boxes after taping. Please refer to figure’s page. The label on the minimum packing unit shows ; Part Number, Lot Number, Ranking, Quantity · In order to protect the LEDs from mechanical shock, we pack them in cardboard boxes for transportation. · The LEDs may be damaged if the boxes are dropped or receive a strong impact against them, so precautions must be taken to prevent any damage. · The boxes are not water resistant and therefore must be kept away from water and moisture. · When the LEDs are transported, we recommend that you use the same packing method as Nichia. 5.LOT NUMBER The first six digits number shows lot number. The lot number is composed of the following characters; -U - Year ( 6 for 2006, 7 for 2007 ) - Month ( 1 for Jan., 9 for Sep., A for Oct., - Nichia's Product Number U - Ranking by Wavelength - Ranking by Optical Power Output - Ranking by Forward Voltage -2- B for Nov. ) Nichia STSE-CC6130A <Cat.No.061218> 6.RELIABILITY (1) TEST ITEMS AND RESULTS Test Item Standard Test Method Test Conditions Resistance to Soldering Heat (Reflow Soldering) Tsld=260°C, 10sec. Note Number of Damaged 2 times 0/10 100 cycles 0/10 Temperature Cycle JEITA ED-4701 100 105 -40°C ~ 25°C ~ 100°C ~ 25°C 30min. 5min. 30min. 5min. High Temperature Storage JEITA ED-4701 200 201 Ta=100°C 500hrs. 0/10 Low Temperature Storage JEITA ED-4701 200 202 Ta=-40°C 500hrs. 0/10 Ta=25°C, IF=500mA 500hrs. 0/10 500hrs. 0/10 500hrs. 0/10 500hrs. 0/10 500hrs. 0/10 48min. 0/10 3 times 0/10 Steady State Operating Life Condition 1 Tested with Nichia standard circuit board. Steady State Operating Life Condition 2 Ta=25°C, IF=700mA Tested with Nichia standard circuit board. Steady State Operating Life of High Temperature Ta=85°C, IF=300mA Tested with Nichia standard circuit board. Steady State Operating Life of High Humidity Heat 60°C, RH=90%, IF=450mA Tested with Nichia standard circuit board. Steady State Operating Life of Low Temperature Ta=-10°C, IF=500mA Tested with Nichia standard circuit board. Vibration JEITA ED-4701 400 403 Electrostatic Discharge JEITA ED-4701 300 304 100 ~ 2000 ~ 100Hz Sweep 4min. 200m/s2 3directions, 4cycles R=1.5kΩ, C=100pF Test Voltage=2kV Negative/Positive Thermal resistance of LED with Nichia standard circuit board : Rja ≒ 35°C/W (2) CRITERIA FOR JUDGING DAMAGE Item Forward Voltage Symbol Test Conditions VF IF=500mA Criteria for Judgement Min. Max. - Initial Level Optical Power Output Po IF=500mA Initial Level 0.7 The test is done after the board is cooled down enough at the room temperature. -3- - 1.1 Nichia STSE-CC6130A <Cat.No.061218> 7.CAUTIONS (1) Cautions · The devices are UV light LEDs. The LED during operation radiates intense UV light, which precautions must be taken to prevent looking directly at the UV light with unaided eyes. Do not look directly into the UV light or look through the optical system. When there is a possibility to receive the reflection of light, protect by using the UV light protective glasses so that light should not catch one’s eye directly. · The caution label is attached to the moisture proof foil bag and cardboard box. ! 危険 UV LED ! DANGER LED 放射 LED RADIATION ビームを直接見たり触れたり しないこと クラス 3B LED製品 AVOID EXPOSURE TO BEAM CLASS 3B LED PRODUCT (2) Storage · Storage Conditions Before opening the package : The LEDs should be kept at 30°C or less and 90%RH or less. The LEDs should be used within a year. When storing the LEDs, moisture proof packaging with absorbent material (silica gel) is recommended. After opening the package : If unused LEDs remain, they should be stored in moisture proof packages, such as sealed containers with packages of moisture absorbent material (silica gel). It is also recommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bag again. · Nichia LED electrodes are gold plated. The silver surface may be affected by environments which contain corrosive substances. Please avoid conditions which may cause the LED to corrode, tarnish or discolor. This corrosion or discoloration may cause difficulty during soldering operations. It is recommended that the User use the LEDs as soon as possible. · Please avoid rapid transitions in ambient temperature, especially in high humidity environments where condensation can occur. (3) Heat Generation · Thermal design of the end product is of paramount importance. Please consider the heat generation of the LED when making the system design. The coefficient of temperature increase per input electric power is affected by the thermal resistance of the circuit board and density of LED placement on the board, as well as other components. It is necessary to avoid intense heat generation and operate within the maximum ratings given in this specification. · Please decide on operating current volume according to LEDs’ ambient temperature and conduct heat release treatment. · The equation 1 indicates correlation between Tj and Ta, and the equation 2 indicates correlation between Tj and Ts. Tj=Ta + Rja W 1 Tj=Ts + Rjs W 2 Tj = Dice Temperature : °C, Ta = Ambient Temperature : °C, Ts = Solder Temperature : °C Rja = Heat resistance from Dice to Ambient temperature : °C /W, Rjs = Heat resistance from Dice to Ts measuring point : °C /W, W = Inputting Power (IF VF) : W · Maximum Tj shall be under 130°C. Keeping Tj less or equal to 100°C is recommended. -4- Nichia STSE-CC6130A <Cat.No.061218> (4) Soldering Conditions · The LEDs can be soldered in place using the reflow soldering method. Nichia cannot make a guarantee on the LEDs after they have been assembled using the dip soldering method. · Recommended soldering conditions Pre-heat Pre-heat time Peak temperature Soldering time Condition Reflow Soldering Lead Solder Lead-free Solder 180 ~ 200°C 120 ~ 150°C 120 sec. Max. 120 sec. Max. 240°C Max. 260°C Max. 10 sec. Max. 10 sec. Max. refer to refer to Temperature - profile 1. Temperature - profile 2. (N2 reflow is recommended.) Although the recommended soldering conditions are specified in the above table, reflow soldering at the lowest possible temperature is desirable for the LEDs. A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature. [Temperature-profile (Surface of circuit board)] Use the conditions shown to the under figure. <1 : Lead Solder> <2 : Lead-free Solder> 2.5 ~ 5°C / sec. 2.5 ~ 5°C / sec. Pre-heating 120 ~ 150°C 60sec.Max. Above 200°C 1~ 5°C / sec. 240°C Max. 10sec. Max. 1~ 5°C / sec. Pre-heating 180 ~ 200°C 60sec.Max. Above 220°C 260°C Max. 10sec. Max. 120sec.Max. 120sec.Max. [Recommended soldering pad design] 8 .4 Use the following conditions shown in the figure. 8 .4 7 4 .2 2 .8 (Unit : mm) · Occasionally there is a brightness decrease caused by the influence of heat or ambient atmosphere during air reflow. It is recommended that the User use the nitrogen reflow method. · Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable, a hot plate should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. · Reflow soldering should not be done more than two times. · When soldering, do not put stress on the LEDs during heating. · After soldering, do not warp the circuit board. (5) Cleaning · Please do not use ultrasonic cleaning, which may reduce the reliability of the product. -5- Nichia STSE-CC6130A-1 <Cat.No.070131> (6) Static Electricity · Static electricity or surge voltage damages the LEDs. It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. · All devices, equipment and machinery must be properly grounded. It is recommended that precautions be taken against surge voltage to the equipment that mounts the LEDs. · When inspecting the final products in which LEDs were assembled, it is recommended to check whether the assembled LEDs are damaged by static electricity or not. It is easy to find static-damaged LEDs by a light-on test or a VF test at a lower current (below 10mA is recommended). The LEDs should be used the light detector etc. when testing the light-on. Do not stare into the LEDs when testing. · Damaged LEDs will show some unusual characteristics such as the forward voltage becomes lower, or the LEDs do not light at the low current. Criteria : (VF > 2.5V at IF=5mA) (7) Safety Guideline for Human Eyes · In 1993, the International Electric Committee (IEC) issued a standard concerning laser product safety (IEC 825-1). Since then, this standard has been applied for diffused light sources (LEDs) as well as lasers. In 1998 IEC 60825-1 Edition 1.1 evaluated the magnitude of the light source. In 2001 IEC 60825-1 Amendment 2 converted the laser class into 7 classes for end products. Components are excluded from this system. Products which contain visible LEDs are now classified as class 1. This LED is classified as class 3B. Products containing LEDs can be classified as class 2 in cases where viewing angles are narrow, optical manipulation intensifies the light, and/or the energy emitted is high. For these systems it is recommended to avoid long term exposure. It is also recommended to follow the IEC regulations regarding safety and labeling of products. (8) Others · NCSU033A complies with RoHS Directive. · The LEDs are attached glass for air sealing and optical performance. If the glass faces are damaged by mechanical objects, there is possibility of losing its air sealing and optical performance. · This LED also emits visible light. Please take notice of visible light spectrum, in case you use this LED as light source of sensors etc. · The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such as office equipment, communications equipment, measurement instruments and household appliances). Consult Nichia’s sales staff in advance for information on the applications in which exceptional quality and reliability are required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control systems, automobiles, traffic control equipment, life support systems and safety devices). · User shall not reverse engineer by disassembling or analysis of the LEDs without having prior written consent from Nichia. When defective LEDs are found, the User shall inform Nichia directly before disassembling or analysis. · The formal specifications must be exchanged and signed by both parties before large volume purchase begins. · The appearance and specifications of the product may be modified for improvement without notice. -6- -7- Forward Voltage VF (V) Ta=25°C 2.5 2.0 1.5 1.0 0.5 0 3.0 3.5 4.0 4.5 5.0 Forward Voltage VF (V) 0 200 400 600 800 1000 1200 Forward Current IFP (mA) Ambient Temperature vs. Forward Voltage Ambient Temperature vs. Relative Power Output 5.0 2.0 IFP=500mA 4.6 4.2 3.8 3.4 3.0 -20 0 20 40 60 80 100 Ambient Temperature Ta (°C) Allowable Forward Current IF (mA) Relative Power Output (a.u.) Ta=25°C 100 10 2.5 1000 3.0 Relative Power Output (a.u.) Forward Current IFP (mA) 2000 1000 Ambient Temperature vs. Allowable Forward Current Forward Current vs. Relative Power Output Forward Voltage vs. Forward Current 800 600 400 Rja=35°C/W Tj =130°C 200 0 0 20 40 60 80 100 Ambient Temperature Ta (°C) IFP=500mA 1.0 0.5 0.2 -20 0 20 40 60 80 100 Ambient Temperature Ta (°C) NICHIA CORPORATION NCSU033A Title CHARACTERISTICS No. 061208658971 Nichia STSE-CC6130A <Cat.No.061218> Model Forward Current vs. Peak Wavelength Ta=25°C 369 367 365 363 361 10 Relative Emission Intensity (a.u.) Peak Wavelength λp (nm) 371 Spectrum 100 1000 Forward Current IFP (mA) Ambient Temperature vs. Peak Wavelength Ta=25°C IFP=500mA 1.0 0.8 0.6 0.4 0.2 0 300 350 400 450 500 550 600 Wavelength λ (nm) Directivity 0° 1.0 -8- IFP=500mA 369 367 365 363 361 -20 0 20 40 60 80 100 Ambient Temperature Ta (°C) Relative Power Output (a.u.) 371 Peak Wavelength λp (nm) 1.2 10° 20° 30° Ta=25°C IFP=500mA 40° 50° 60° 0.5 70° 80° 0 90° 60° 30° Radiation Angle 0° 0.5 NICHIA CORPORATION NCSU033A Title CHARACTERISTICS No. 061208658981 Nichia STSE-CC6130A <Cat.No.061218> Model 90° 1.0 6 .6 6 .8 4 .2 Φ 4 .35 2 .1 Anode 2 .8 LED Die 0 .65 Anode Cathode 0 .65 Cathode 6 .6 6 .8 Cathode ma rk Protection device -9Ts ( ※ ) A ½ K Ts : Measure point of solder ½½ NCSU033A has a protection device built in as a protection circuit against static electricity. MATERIALS Ceramics Hard Glass Au Plating Model NICHIA CORPORATION Title No. NCSU033A Unit mm OUTLINE DIMENSIONS 061130658591 Allow ±0.2 Nichia STSE-CC6130A <Cat.No.061218> ITEM PACKAGE GLASS ELECTRODES Internal Circuit +0.1 ±0.05 ±0.1 2 ±0.1 ±0.1 0.29 7.15 5.5 ±0.05 +0.3 4 12-0.1 ±0.1 12 1.75 φ1.5-0 ±0.1 7.15 +0.25 φ1.5-0 ±0.1 2.5 LEDs mounting part -10Top cover tape トップカバーテープ Embossed carrier tape エンボスキャリアテープ 100pcs/bag NCxU033x Title PACKING No. 061130536742 Unit mm Scale Allow Nichia STSE-CC6130A <Cat.No.061218> NICHIA CORPORATION Model Nichia STSE-CC6130A <Cat.No.061218> The IC pack and moisture absorbent material are put in the moisture proof foil bag and then heat sealed. IC pack Label NICHIA Seal UV TYPE LOT QTY LED NCxU033x xxxxxx-Uz PCS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Caution Label Moisture absorbent material ! 危険 Moisture proof foil bag UV LED ! DANGER LED RADIATION LED放射 ビームを直接見たり触れたり しないこと クラス 3B LED製品 AVOID EXPOSURE TO BEAM CLASS 3B LED PRODUCT ¼This Caution Label is applied on Moisture proof foil bag and on Cardboard box. Empty space in the box is filled with cushion material. Label NICHIA Nichia LED UV TYPE RANK QTY LED NCxU033x Uz PCS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Packing unit Moisture proof foil bag Cardboard box Cardboard box S Quantity/bag (pcs) 100 MAX. Dimensions (mm) 250¯140¯90¯4t NICHIA CORPORATION -11- Bag/box 5bag MAX. Quantity/box (pcs) 500 MAX. Model NCxU033x Title PACKING No. 061130536752 Taping part Reel part +0 φ180-3 ±0.05 2 ±0.1 φ1.5 ±0.1 12 4 1.75 +0.1 -0 ±1 17.5 ±0.5 13.5 ±0.1 0.29 ±0.1 7.15 +0.25 φ1.5-0 .2 ±0 3 φ1 Label ±0.1 2.5 UV TYPE LOT QTY No LEDs φ60+1 -0 7.15 +0.3 φ 21 ±0. 8 5.5 ±0.05 12-0.1 ±0.1 Cathode LED NCxU033xT XXXXXX-△■● pcs LEDs mounting part No LEDs -12Pull direction Top cover tape トップカバーテープ Embossed carrier tape エンボスキャリアテープ 500pcs/Reel Reel Lead Min. 40mm Reel Lead Min. 320mm (No LEDs is more than 27) Reel Lead Min. 400mm Model NICHIA CORPORATION Title No. NCxU033xT TAPING DIMENSIONS 061130536762 Unit mm Scale Allow Nichia STSE-CC6130A <Cat.No.061218> Taping is based on the JIS C 0806 : Packaging of Electronic Components on Continuous Tapes. Nichia STSE-CC6130A <Cat.No.061218> The reel and moisture absorbent material are put in the moisture proof foil bag and then heat sealed. Reel Label NICHIA Seal UV TYPE LOT QTY LED NCxU033xT xxxxxx-Uz PCS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Caution Label Moisture absorbent material ! 危険 Moisture proof foil bag UV LED ! DANGER LED RADIATION LED放射 ビームを直接見たり触れたり しないこと クラス 3B LED製品 AVOID EXPOSURE TO BEAM CLASS 3B LED PRODUCT ¼This Caution Label is applied on Moisture proof foil bag and on Cardboard box. The box is partitioned with the cardboard. Label NICHIA Nichia LED UV TYPE RANK QTY LED NCxU033xT Uz PCS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Packing unit Moisture proof foil bag Cardboard box Cardboard box S Cardboard box M Cardboard box L Reel/bag 1reel Quantity/bag (pcs) 500 MAX. Dimensions (mm) 291¯237¯120¯8t 259¯247¯243¯5t 444¯262¯259¯8t Reel/box 5reel MAX. 10reel MAX. 20reel MAX. Model NICHIA CORPORATION -13- Quantity/box (pcs) 2,500 MAX. 5,000 MAX. 10,000 MAX. NCxU033xT Title PACKING No. 061130542462