PCM1802 SLES023C – DECEMBER 2001 – REVISED JANUARY 2005 SINGLE-ENDED ANALOG-INPUT 24-BIT, 96-kHz STEREO A/D CONVERTER FEATURES APPLICATIONS • • • • • • • • • • • • • • • 24-Bit Delta-Sigma Stereo A/D Converter Single-Ended Voltage Input: 3 V p-p Antialiasing Filter Included Oversampling Decimation Filter – Oversampling Frequency: ×64, ×128 – Pass-Band Ripple: ±0.05 dB – Stop-Band Attenuation: –65 dB – On-Chip High-Pass Filter (HPF): 0.84 Hz (44.1 kHz) High Performance – THD+N: 96 dB (Typical) – SNR: 105 dB (Typical) – Dynamic Range: 105 dB (Typical) PCM Audio Interface – Master/Slave Mode Selectable – Data Formats: 24-Bit Left-Justified; 24-Bit I2S; 20-, 24-Bit Right-Justified Sampling Rate: 16 kHz to 96 kHz System Clock: 256 fS, 384 fS, 512 fS, 768 fS Dual Power Supplies: 5 V for Analog, 3.3 V for Digital Package: 20-Pin SSOP AV Amplifier Receiver MD Player CD Recorder Multitrack Receiver Electric Musical Instrument DESCRIPTION The PCM1802 is a high-performance, low-cost, single-chip stereo analog-to-digital converter with single-ended analog voltage input. The PCM1802 uses a delta-sigma modulator with 64- or 128-times oversampling, and includes a digital decimation filter and high-pass filter (HPF), which removes the dc component of the input signal. For various applications, the PCM1802 supports master and slave modes and four data formats in serial interface. The PCM1802 is suitable for a wide variety of costsensitive consumer applications where good performance, 5-V analog supply, and 3.3-V digital supply operation is required. The PCM1802 is fabricated using a highly advanced CMOS process and is available in the DB 20-pin SSOP package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. System Two, Audio Precision are trademarks of Audio Precision. All other trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2001–2005, Texas Instruments Incorporated PCM1802 www.ti.com SLES023C – DECEMBER 2001 – REVISED JANUARY 2005 This device contains circuits to protect its inputs and outputs against damage due to high static voltages or electrostatic fields. These circuits have been qualified to protect this device against electrostatic discharges (ESD) of up to 2 kV according to MIL-STD-883C, Method 3015; however, it is advised that precautions be taken to avoid application of any voltage higher than maximum-rated voltages to these high-impedance circuits. During storage or handling, the device leads should be shorted together or the device should be placed in conductive foam. In a circuit, unused inputs should always be connected to an appropriated logic voltage level, preferably either VCC or ground. Specific guidelines for handling devices of this type are contained in the publication Electrostatic Discharge (ESD) (SSYA010) available from Texas Instruments. PIN ASSIGNMENTS PCM1802 (TOP VIEW) VINL VINR VREF1 VREF2 VCC AGND PDWN BYPAS FSYNC LRCK 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 MODE1 MODE0 FMT1 FMT0 OSR SCKI VDD DGND DOUT BCK P0009-02 BLOCK DIAGRAM VINL Single-End /Differential Converter 5th Order Delta-Sigma Modulator ×1/64 (×1/128) Decimation Filter with High-Pass Filter VREF1 Reference VREF2 VINR Single-End /Differential Converter BCK LRCK Serial Interface FSYNC DOUT Mode/ Format Control 5th Order Delta-Sigma Modulator FMT0 FMT1 MODE0 MODE1 BYPAS Clock and Timing Control Power Supply VCC AGND DGND OSR PDWN SCKI VDD B0004-07 2 PCM1802 www.ti.com SLES023C – DECEMBER 2001 – REVISED JANUARY 2005 Terminal Functions TERMINAL NAME PIN AGND 6 BCK 11 BYPAS 8 DGND DOUT I/O – DESCRIPTIONS Analog GND I/O Bit clock input/output (1) I HPF bypass control. Low: normal mode (dc cut); High: bypass mode (through) (2) 13 – Digital GND 12 O Audio data output FMT0 17 I Audio data format select 0. See data format (2) FMT1 18 I Audio data format select 1. See data format (2) FSYNC 9 I/O Frame synchronous clock input/output(1) LRCK 10 I/O Sampling clock input/output(1) MODE0 19 I Mode select 0. See interface mode(2) MODE1 20 I Mode select 1. See interface mode(2) OSR 16 I Oversampling ratio select. Low: ×64 fS; High: ×128 fS(2) PDWN 7 I Power-down control, active-low(2) SCKI 15 I System clock input; 256 fS, 384 fS, 512 fS, or 768 fS (3) VCC 5 – Analog power supply, 5 V VDD 14 – Digital power supply, 3.3 V VINL 1 I Analog input, L-channel VINR 2 I Analog input, R-channel VREF1 3 – Reference-1 decoupling capacitor VREF2 4 – Reference-2 voltage input, normally connected to VCC (1) (2) (3) Schmitt-trigger input Schmitt-trigger input with internal pulldown (50 kΩ typically), 5-V tolerant Schmitt-trigger input, 5-V tolerant ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) (1) Supply voltage VCC 6.5 V VDD 4V Ground voltage differences AGND, DGND Supply voltage difference VCC, VDD Digital input voltage FSYNC, LRCK, BCK, DOUT PDWN, BYPAS, SCKI, OSR, FMT0, FMT1, MODE0, MODE1 Analog input voltage Input current (any pins except supplies) VINL, VINR, VREF1, VREF2 ±0.1 V VCC – VDD < 3.0 V –0.3 V to (VDD + 0.3 V) –0.3 V to 6.5 V –0.3 V to (VCC + 0.3 V) ±10 mA Ambient temperature under bias –40°C to 125°C Storage temperature –55°C to 150°C Junction temperature Lead temperature (soldering) Package temperature (IR reflow, peak) (1) 150°C 260°C, 5 s 260°C Stresses beyond those listed under "absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 3 PCM1802 www.ti.com SLES023C – DECEMBER 2001 – REVISED JANUARY 2005 ELECTRICAL CHARACTERISTICS all specifications at TA = 25°C, VCC = 5 V, VDD = 3.3 V, master mode, fS = 44.1 kHz, system clock = 384 fS, oversampling ratio = ×128, 24-bit data (unless otherwise noted) TEST CONDITIONS PCM1802DB MIN TYP Resolution UNIT MAX 24 Bits DATA FORMAT Left-justified, I2S, right-justified Audio data interface format Audio data bit length 20, 24 Audio data format fS Bits MSB first, 2s complement Sampling frequency System clock frequency 16 44.1 96 256 fS 4.096 11.2896 24.576 384 fS 6.144 16.9344 36.864 512 fS 8.192 22.5792 49.152 768 fS 12.288 33.8688 (1) kHz MHz INPUT LOGIC VIH (2) 2 VDD VIL (2) 0 0.8 2 5.5 VIH (3) Input logic level VIL (3) 0 IIH (4) IIL (4) IIH (5) Input logic current IIL (5) 0.8 VIN = VDD ±10 VIN = 0 V ±10 VIN = VDD VDC 65 100 µA ±10 VIN = 0 V OUTPUT LOGIC VOH (6) VOL (6) IOUT = –1 mA Output logic level 2.8 IOUT = 1 mA 0.5 VDC DC ACCURACY Gain mismatch, channel-to-channel Gain error Bipolar zero error DYNAMIC PERFORMANCE HPF bypassed (7) Total harmonic distortion + noise S/N ratio (1) (2) (3) (4) (5) (6) (7) (8) (9) 4 ±2 ±6 %FSR ±2 %FSR 0.0015% (9) fS = 96 kHz, VIN = –0.5 dB fS = 96 kHz, A-weighted 1.2% 100 (9) fS = 44.1 kHz, A-weighted fS = 96 kHz, A-weighted 0.7% (9) fS = 44.1 kHz, A-weighted (9) 0.003% 0.0025% fS = 44.1 kHz, VIN = –60 dB fS = 96 kHz, VIN = –60 dB Dynamic range ±4 %FSR (8) fS = 44.1 kHz, VIN = –0.5 dB THD+N ±1 105 103 100 105 103 dB dB Maximum system clock frequency is not applicable at 768 fS, fS = 96 kHz. See the System Clock section of this data sheet. Pins 9–11: FSYNC, LRCK, BCK (Schmitt-trigger input in slave mode) Pins 7–8, 15–20: PDWN, BYPAS, SCKI, OSR, FMT0, FMT1, MODE0, MODE1 (Schmitt-trigger input, 5-V tolerant) Pins 9–11, 15: FSYNC, LRCK, BCK (Schmitt-trigger input in slave mode), SCKI (Schmitt-trigger input) Pins 7–8, 16–20: PDWN, BYPAS, OSR, FMT0, FMT1, MODE0, MODE1 (Schmitt-trigger input, with 50-kΩ typical pulldown resistor) Pins 9–12: FSYNC, LRCK, BCK (in master mode), DOUT High-pass filter Analog performance specifications are tested with System Two™ audio measurement system by Audio Precision™, using 400-Hz HPF, 20-kHz LPF for 44.1-kHz operation, 40-kHz LPF for 96-kHz operation in RMS mode. fS = 96 kHz, system clock = 256 fS, oversampling ratio = ×64. PCM1802 www.ti.com SLES023C – DECEMBER 2001 – REVISED JANUARY 2005 ELECTRICAL CHARACTERISTICS (continued) all specifications at TA = 25°C, VCC = 5 V, VDD = 3.3 V, master mode, fS = 44.1 kHz, system clock = 384 fS, oversampling ratio = ×128, 24-bit data (unless otherwise noted) PCM1802DB TEST CONDITIONS Channel separation MIN fS = 44.1 kHz fS = 96 kHz 96 (9) TYP MAX 103 UNIT dB 98 ANALOG INPUT Input voltage 0.6 VCC Vp-p Center voltage (VREF1) 0.5 VCC V Input impedance Antialiasing filter frequency response –3 dB 20 kΩ 300 kHz DIGITAL FILTER PERFORMANCE Pass band 0.454 fS Stop band 0.583 fS Hz ±0.05 Pass-band ripple Stop-band attenuation –65 Delay time HPF frequency response –3 dB Hz dB dB 17.4/fS s 0.019 fS mHz POWER SUPPLY REQUIREMENTS VCC VDD ICC IDD PD 4.5 5 5.5 2.7 3.3 3.6 VCC = 5 V, VDD = 3.3 V 24 30 fS = 44.1 kHz VCC = 5 V, VDD = 3.3 V 8.3 10 Voltage range Supply current (10) V(8) 17 fS = 44.1 kHz, VCC = 5 V, VDD = 3.3 V 147 fS = 96 kHz, VCC = 5 V, VDD = 3.3 V(8) 176 VCC = 5 V, VDD = 3.3 V 0.5 fS = 96 kHz, VCC = 5 V, VDD = 3.3 Power dissipation; operation Power dissipation; power down 183 VDC mA mW mW TEMPERATURE RANGE Operation temperature Thermal resistance (θJA) –40 20-pin SSOP 85 115 °C °C/W (10) Minimum load on DOUT (pin 12), BCK (pin 11), LRCK (pin 10), FSYNC (pin 9) 5 PCM1802 www.ti.com SLES023C – DECEMBER 2001 – REVISED JANUARY 2005 TYPICAL PERFORMANCE CURVES OF INTERNAL FILTER Digital Filter—Decimation Filter Frequency Response AMPLITUDE vs FREQUENCY AMPLITUDE vs FREQUENCY 50 50 Oversampling Ratio = 128 Oversampling Ratio = 64 0 Amplitude − dB Amplitude − dB 0 −50 −100 −150 −50 −100 −150 −200 −200 0 8 16 24 32 40 48 56 64 Frequency [× fS] 0 8 16 24 32 Frequency [× fS] G001 Figure 1. Overall Characteristics G002 Figure 2. Overall Characteristics AMPLITUDE vs FREQUENCY AMPLITUDE vs FREQUENCY 0.2 0 −10 0.0 −20 Amplitude − dB Amplitude − dB −30 −40 −50 −60 −70 −80 −90 −0.2 −0.4 −0.6 −0.8 Oversampling Ratio = 128 and 64 −100 0.00 0.25 Oversampling Ratio = 128 and 64 0.50 0.75 1.00 Frequency [× fS] Figure 3. Stop-Band Attenuation Characteristics G003 −1.0 0.0 0.1 0.2 0.3 0.4 0.5 Frequency [× fS] 0.6 G004 Figure 4. Pass-Band Ripple Characteristics All specifications at TA = 25°C, VCC = 5 V, VDD = 3.3 V, master mode, fS = 44.1 kHz, system clock = 384 fS, oversampling ratio = ×128, 24-bit data, unless otherwise noted. 6 PCM1802 www.ti.com SLES023C – DECEMBER 2001 – REVISED JANUARY 2005 TYPICAL PERFORMANCE CURVES OF INTERNAL FILTER (continued) HPF (High-Pass Filter) Frequency Response AMPLITUDE vs FREQUENCY AMPLITUDE vs FREQUENCY 0.2 0 −10 0.0 −20 Amplitude − dB Amplitude − dB −30 −40 −50 −60 −70 −80 −0.2 −0.4 −0.6 −0.8 −90 −100 0.0 −1.0 0.1 0.2 0.3 Frequency [× fS/1000] 0 0.4 1 2 3 4 Frequency [× fS/1000] G005 Figure 5. HPF Stop-Band Characteristics G006 Figure 6. HPF Pass-Band Characteristics Analog Filter—Antialiasing Filter Frequence Response AMPLITUDE vs FREQUENCY 0 0.0 −5 −0.1 −10 −0.2 −15 −0.3 Amplitude − dB Amplitude − dB AMPLITUDE vs FREQUENCY −20 −25 −30 −0.4 −0.5 −0.6 −35 −0.7 −40 −0.8 −45 −0.9 −50 100 −1.0 1k 10k 100k 1M 10M 1 10 100 1k 10k 100k f − Frequency − Hz f − Frequency − Hz G007 Figure 7. Antialias Filter Stop-Band Characteristics G008 Figure 8. Antialias Filter Pass-Band Characteristics All specifications at TA = 25°C, VCC = 5 V, VDD = 3.3 V, master mode, fS = 44.1 kHz, system clock = 384 fS, oversampling ratio = ×128, 24-bit data, unless otherwise noted. 7 PCM1802 www.ti.com SLES023C – DECEMBER 2001 – REVISED JANUARY 2005 TYPICAL PERFORMANCE CURVES TOTAL HARMONIC DISTORTION + NOISE vs FREE-AIR TEMPERATURE DYNAMIC RANGE and SNR vs FREE-AIR TEMPERATURE 110 109 Dynamic Range and SNR − dB THD+N − Total Harmonic Distortion + Noise − % 0.004 0.003 0.002 107 Dynamic Range 106 105 SNR 104 103 102 101 0.001 −50 −25 0 25 50 75 TA − Free-Air Temperature − °C 100 −50 100 −25 0 25 50 75 TA − Free-Air Temperature − °C G009 Figure 9. Figure 10. TOTAL HARMONIC DISTORTION + NOISE vs SUPPLY VOLTAGE DYNAMIC RANGE and SNR vs SUPPY VOLTAGE 100 G010 110 0.004 109 Dynamic Range and SNR − dB THD+N − Total Harmonic Distortion + Noise − % 108 0.003 0.002 108 107 Dynamic Range 106 105 SNR 104 103 102 101 0.001 4.25 4.50 4.75 5.00 5.25 VCC − Supply Voltage − V Figure 11. 5.50 5.75 G011 100 4.25 4.50 4.75 5.00 5.25 VCC − Supply Voltage − V 5.50 5.75 G012 Figure 12. All specifications at TA = 25°C, VCC = 5 V, VDD = 3.3 V, master mode, fS = 44.1 kHz, system clock = 384 fS, oversampling ratio = ×128, 24-bit data, unless otherwise noted. 8 PCM1802 www.ti.com SLES023C – DECEMBER 2001 – REVISED JANUARY 2005 TYPICAL PERFORMANCE CURVES (continued) TOTAL HARMONIC DISTORTION + NOISE vs fSAMPLE CONDITION DYNAMIC RANGE and SNR vs fSAMPLE CONDITION 110 †f S = 48 kHz, System Clock = 256 fS, Oversampling Ratio = ×128. ‡f = 96 kHz, System Clock = 256 f , S S Oversampling Ratio = ×64. †f S = 48 kHz, System Clock = 256 fS, Oversampling Ratio = ×128. ‡f = 96 kHz, System Clock = 256 f , S S Oversampling Ratio = ×64. 109 Dynamic Range and SNR − dB THD+N − Total Harmonic Distortion + Noise − % 0.004 0.003 0.002 108 107 Dynamic Range 106 105 SNR 104 103 102 101 100 0.001 0 10 20† 30‡ 44.1 48 96 fSAMPLE Condition − kHz 0 40 20† 48 10 44.1 30‡ 96 fSAMPLE Condition − kHz G013 Figure 13. Figure 14. AMPLITUE vs FREQUENCY AMPLITUDE vs FREQUENCY 40 G014 Output Spectrum 0 0 Input Level = −60 dB Data Points = 8192 −20 −20 −40 −40 Amplitude − dB Amplitude − dB Input Level = −0.5 dB Data Points = 8192 −60 −80 −60 −80 −100 −100 −120 −120 −140 −140 0 5 10 15 20 0 5 10 f − Frequency − kHz 20 G016 G015 Figure 15. 15 f − Frequency − kHz Figure 16. All specifications at TA = 25°C, VCC = 5 V, VDD = 3.3 V, master mode, fS = 44.1 kHz, system clock = 384 fS, oversampling ratio = ×128, 24-bit data, unless otherwise noted. 9 PCM1802 www.ti.com SLES023C – DECEMBER 2001 – REVISED JANUARY 2005 TYPICAL PERFORMANCE CURVES (continued) TOTAL HARMONIC DISTORTION + NOISE vs SIGNAL LEVEL THD+N − Total Harmonic Distortion + Noise − % 100 10 1 0.1 0.01 0.001 −100 −90 −80 −70 −60 −50 −40 −30 −20 −10 0 Signal Level − dB G017 Figure 17. Supply Current SUPPLY CURRENT vs fSAMPLE CONDITION ICC and IDD − Supply Current − mA 30 ICC 25 20 15 IDD 10 †f S = 48 kHz, System Clock = 256 fS, Oversampling Ratio = ×128. ‡f = 96 kHz, System Clock = 256 f , S S Oversampling Ratio = ×64. 5 0 0 10 44.1 20† 48 30‡ 96 fSAMPLE Condition − kHz 40 G018 Figure 18. All specifications at TA = 25°C, VCC = 5 V, VDD = 3.3 V, master mode, fS = 44.1 kHz, system clock = 384 fS, oversampling ratio = ×128, 24-bit data, unless otherwise noted. 10 PCM1802 www.ti.com SLES023C – DECEMBER 2001 – REVISED JANUARY 2005 PRINCIPLES OF OPERATION The PCM1802 consists of a reference circuit, two channels of single-ended-to-differential converter, a fifth-order delta-sigma modulator with full differential architecture, a decimation filter with high-pass filter, and a serial interface circuit. Figure 19 illustrates the total architecture of the PCM1802, Figure 20 illustrates the architecture of single-ended-to-differential converter and antialiasing filter, and Figure 21 is the block diagram of the fifth-order delta-sigma modulator and transfer function. An on-chip high-precision reference with one external capacitor provides all reference voltages that are needed in the PCM1802 and defines the full-scale voltage range for both channels. On-chip single-ended-to-differential signal converters save the design, space, and extra parts cost for external signal converters. Full-differential architecture provides a wide dynamic range and excellent power-supply rejection performance. The input signal is sampled at a ×64 or ×128 oversampling rate, thus eliminating an external sample-hold amplifier. A fifth-order delta-sigma noise shaper, which consists of five integrators using the switched capacitor technique and a comparator, shapes the quantization noise generated by the comparator and 1-bit DAC outside of the audio signal band. The high-order delta-sigma modulation randomizes the modulator outputs and reduces the idle tone level. The 64-fS or 128-fS, 1-bit stream from the delta-sigma modulator is converted to a 1-fS, 24-bit or 20-bit digital signal by removing high-frequency noise components with a decimation filter. The dc component of the signal is removed by the HPF, and the HPF output is converted to a time-multiplexed serial signal through the serial interface, which provides flexible serial formats. VINL Single-End /Differential Converter 5th Order Delta-Sigma Modulator ×1/64 (×1/128) Decimation Filter with High-Pass Filter VREF1 Reference VREF2 VINR Single-End /Differential Converter BCK LRCK Serial Interface FSYNC DOUT Mode/ Format Control 5th Order Delta-Sigma Modulator FMT0 FMT1 MODE0 MODE1 BYPAS Clock and Timing Control Power Supply OSR PDWN SCKI VCC AGND DGND VDD B0004-07 Figure 19. Block Diagram 11 PCM1802 www.ti.com SLES023C – DECEMBER 2001 – REVISED JANUARY 2005 PRINCIPLES OF OPERATION (continued) 1 µF 20 kΩ + VINL − 1 − + (+) + (−) VREF1 Delta-Sigma Modulator 3 + 0.1 µF Reference 10 µF VREF2 4 VCC 5 S0011-05 Figure 20. Analog Front End (Left Channel) Analog In X(z) + − 1st SW-CAP Integrator + − 2nd SW-CAP Integrator + 3rd SW-CAP Integrator + + + + − 4th SW-CAP Integrator + 5th SW-CAP Integrator + H(z) + Qn(z) Digital Out Y(z) + Comparator 1-Bit DAC Y(z) = STF(z) * X(z) + NTF(z) * Qn(z) Signal Transfer Function STF(z) = H(z) / [1 + H(z)] Noise Transfer Function NTF(z) = 1 / [1 + H(z)] B0005-02 Figure 21. Block Diagram of Fifth-Order Delta-Sigma Modulator 12 PCM1802 www.ti.com SLES023C – DECEMBER 2001 – REVISED JANUARY 2005 PRINCIPLES OF OPERATION (continued) System Clock The PCM1802 supports 256 fS, 384 fS, 512 fS, and 768 fS as the system clock, where fS is the audio sampling frequency. The system clock must be supplied on SCKI (pin 15). The PCM1802 has a system clock detection circuit which automatically senses if the system clock is operating at 256 fS, 384 fS, 512 fS, or 768 fS in slave mode. In master mode, the system clock frequency must be selected by MODE0 (pin 19) and MODE1 (pin 20), and 768 fS is not available. For system clock inputs of 384 fS, 512 fS, and 768 fS, the system clock is divided to 256 fS automatically, and the 256 fS clock is used to operate the delta-sigma modulator and the digital filter. Table 1 shows the relationship of typical sampling frequencies and system clock frequencies, and Figure 22 shows system clock timing. Table 1. Sampling Frequency and System Clock Frequency SAMPLING RATE FREQUENCY (kHz) SYSTEM CLOCK FREQUENCY (MHz) 256 fS 384 fS 512 fS 768 fS 32 8.192 12.288 16.384 24.576 44.1 11.2896 16.9344 22.5792 33.8688 48 12.288 18.432 24.576 36.864 64 16.384 24.576 32.768 49.152 88.2 22.5792 33.8688 45.1584 — 96 24.576 36.864 49.152 — t(SCKH) t(SCKL) SCKI 2V SCKI 0.8 V T0005A07 PARAMETER MIN MAX UNIT t(SCKH) System clock-pulse duration, high 7 ns t(SCKL) System clock-pulse duration, low 7 ns Figure 22. System Clock Timing 13 PCM1802 www.ti.com SLES023C – DECEMBER 2001 – REVISED JANUARY 2005 Power-On Reset Sequence The PCM1802 has an internal power-on reset circuit, and initialization (reset) is performed automatically when the power supply (VDD) exceeds 2.2 V (typical). While VDD < 2.2 V (typical), and for 1024 system-clock counts after VDD > 2.2 V (typical), the PCM1802 stays in the reset state and the digital output is forced to zero. The digital output is valid after the reset state is released and the time of 4480/fS has passed. Figure 23 illustrates the internal power-on reset timing and the digital output for power-on reset. VDD 2.6 V 2.2 V 1.8 V Reset Reset Removal Internal Reset 1024 System Clocks 4480 / fS System Clock DOUT Zero Data Normal Data T0014-05 Figure 23. Internal Power-On Reset Timing Serial Audio Data Interface The PCM1802 interfaces with the audio system through BCK (pin 11), LRCK (pin 10), FSYNC (pin 9), and DOUT (pin 12). 14 PCM1802 www.ti.com SLES023C – DECEMBER 2001 – REVISED JANUARY 2005 Interface Mode The PCM1802 supports master mode and slave mode as interface modes, and they are selected by MODE1 (pin 20) and MODE0 (pin 19) as shown in Table 2. In master mode, the PCM1802 provides the timing for serial audio data communications between the PCM1802 and the digital audio processor or external circuit. In slave mode, the PCM1802 receives the timing for data transfer from an external controller. Table 2. Interface Mode MODE1 MODE0 0 0 Slave mode (256 fS, 384 fS, 512 fS, 768 fS) INTERFACE MODE 0 1 Master mode (512 fS) 1 0 Master mode (384 fS) 1 1 Master mode (256 fS) Master mode In master mode, BCK, LRCK, and FSYNC work as output pins, and these pins are controlled by timing which is generated in the clock circuit of the PCM1802. FSYNC is used to designate the valid data from the PCM1802. The rising edge of FSYNC indicates the starting point of the converted audio data and the falling edge of this signal indicates the ending point of the data. The frequency of this signal is fixed at 2 × LRCK. The duty cycle ratio depends on data bit length. The frequency of BCK is fixed at 64 × LRCK. The 768 fS system clock is not available in master mode. Slave mode In slave mode, BCK, LRCK, and FSYNC work as input pins. FSYNC is used to enable the BCK signal, and the PCM1802 can shift out the converted data while FSYNC is HIGH. The PCM1802 accepts either the 64 BCK/LRCK or the 48 BCK/LRCK format. The delay of FSYNC from the LRCK transition must be within 16 BCKs for the 64 BCK/LRCK format and within 12 BCKs for the 48 BCK/LRCK format. Data Format The PCM1802 supports four audio data formats in both master and slave modes, and they are selected by FMT1 (pin 18) and FMT0 (pin 17) as shown in Table 3. Figure 24 and Figure 26 illustrate the data formats in slave mode and master mode, respectively. Table 3. Data Format FORMAT# FMT1 FMT0 0 0 0 Left-justified, 24-bit FORMAT 1 0 1 I2S, 24-bit 2 1 0 Right-justified, 24-bit 3 1 1 Right-justified, 20-bit 15 PCM1802 www.ti.com SLES023C – DECEMBER 2001 – REVISED JANUARY 2005 Interface Timing Figure 25 and Figure 27 illustrate the interface timing in slave mode and master mode, respectively. FORMAT 0: FMT[1:0] = 00 24-Bit, MSB-First, Left-Justified FSYNC Left-Channel LRCK Right-Channel BCK DOUT 1 2 3 22 23 24 MSB 1 LSB 2 3 22 23 24 MSB 1 LSB FORMAT 1: FMT[1:0] = 01 24-Bit, MSB-First, I2S FSYNC LRCK Left-Channel Right-Channel BCK DOUT 1 2 3 22 23 24 1 LSB MSB 2 3 22 23 24 LSB MSB FORMAT 2: FMT[1:0] = 10 24-Bit, MSB-First, Right-Justified FSYNC Left-Channel LRCK Right-Channel BCK DOUT 24 1 2 3 22 23 24 MSB LSB 1 2 3 22 23 24 MSB LSB FORMAT 3: FMT[1:0] = 11 20-Bit, MSB-First, Right-Justified FSYNC LRCK Left-Channel Right-Channel BCK DOUT 20 1 2 MSB 3 18 19 20 LSB 1 2 MSB 3 18 19 20 LSB T0016-12 Figure 24. Audio Data Format (Slave Mode: FSYNC, LRCK, and BCK Work as Inputs) 16 PCM1802 www.ti.com SLES023C – DECEMBER 2001 – REVISED JANUARY 2005 1.4 V FSYNC t(FSSU) t(FSHD) t(LRCP) 1.4 V LRCK t(BCKL) t(BCKH) t(LRSU) t(LRHD) 1.4 V BCK t(CKDO) t(BCKP) t(LRDO) 0.5 VDD DOUT T0017-01 PARAMETER MIN TYP MAX UNIT t(BCKP) BCK period 150 ns t(BCKH) BCK pulse duration, high 60 ns t(BCKL) BCK pulse duration, low 60 ns t(LRSU) LRCK setup time to BCK rising edge 40 ns t(LRHD) LRCK hold time to BCK rising edge 20 ns t(LRCP) LRCK period 10 µs t(FSSU) FSYNC setup time to BCK rising edge 20 ns t(FSHD) FSYNC hold time to BCK rising edge t(CKDO) Delay time, BCK falling edge to DOUT valid –10 20 ns t(LRDO) Delay time, LRCK edge to DOUT valid –10 20 ns tr Rise time of all signals 10 ns tf Fall time of all signals 10 ns 20 ns NOTE: Timing measurement reference level is (VIH + VIL)/2. Rise and fall times are measured from 10% to 90% of IN/OUT signal swing. Load capacitance of DOUT is 20 pF. Figure 25. Audio Data Interface Timing (Slave Mode: FSYNC, LRCK, and BCK Work as Inputs) 17 PCM1802 www.ti.com SLES023C – DECEMBER 2001 – REVISED JANUARY 2005 FORMAT 0: FMT[1:0] = 00 24-Bit, MSB-First, Left-Justified FSYNC Left-Channel LRCK Right-Channel BCK DOUT 1 2 3 22 23 24 MSB 1 LSB 2 3 22 23 24 MSB 1 LSB FORMAT 1: FMT[1:0] = 01 24-Bit, MSB-First, I2S FSYNC LRCK Left-Channel Right-Channel BCK DOUT 1 2 3 22 23 24 1 LSB MSB 2 3 22 23 24 LSB MSB FORMAT 2: FMT[1:0] = 10 24-Bit, MSB-First, Right-Justified FSYNC Left-Channel LRCK Right-Channel BCK DOUT 24 1 2 3 22 23 24 MSB LSB 1 2 3 22 23 24 MSB LSB FORMAT 3: FMT[1:0] = 11 20-Bit, MSB-First, Right-Justified FSYNC Left-Channel LRCK Right-Channel BCK DOUT 20 1 2 MSB 3 18 19 20 LSB 1 2 MSB 3 18 19 20 LSB T0016-13 Figure 26. Audio Data Format (Master Mode: FSYNC, LRCK, and BCK Work as Outputs) 18 PCM1802 www.ti.com SLES023C – DECEMBER 2001 – REVISED JANUARY 2005 t(FSYP) 0.5 VDD FSYNC t(CKFS) t(LRCP) 0.5 VDD LRCK t(BCKL) t(BCKH) t(CKLR) 0.5 VDD BCK t(BCKP) t(CKDO) t(LRDO) 0.5 VDD DOUT T0018-01 PARAMETER MIN TYP MAX UNIT 150 1/(64 fS) 1200 ns 75 600 ns 75 600 ns t(BCKP) BCK period t(BCKH) BCK pulse duration, high t(BCKL) BCK pulse duration, low t(CKLR) Delay time, BCK falling edge to LRCK valid t(LRCP) LRCK period t(CKFS) Delay time, BCK falling edge to FSYNC valid t(FSYP) FSYNC period t(CKDO) Delay time, BCK falling edge to DOUT valid –10 t(LRDO) Delay time, LRCK edge to DOUT valid –10 tr tf –10 20 ns 80 µs 20 ns 40 µs 20 ns 20 ns Rise time of all signals 10 ns Fall time of all signals 10 ns 10 1/fS –10 5 1/(2 fS) NOTE: Timing measurement reference level is (VIH + VIL) / 2. Rise and fall times are measured from 10% to 90% of IN/OUT signal swing. Load capacitance of all signals is 20 pF. Figure 27. Audio Data Interface Timing (Master Mode: FSYNC, LRCK, and BCK Work as Outputs) Synchronization With Digital Audio System In slave mode, the PCM1802 operates under LRCK, synchronized with system clock SCKI. The PCM1802 does not need a specific phase relationship between LRCK and SCKI, but does require the synchronization of LRCK and SCKI. If the relationship between LRCK and SCKI changes more than ±6 BCKs for 64 BCK/frame (±5 BCKs for 48 BCK/frame) during one sample period due to LRCK or SCKI jitter, internal operation of the ADC halts within 1/fS and digital output is forced into BPZ code until resynchronization between LRCK and SCKI is completed. In the case of changes less than ±5 BCKs for 64 BCK/frame (±4 BCKs for 48 BCK/frame), resynchronization does not occur. Figure 28 illustrates the digital output response for loss of synchronization and resynchronization. During undefined data, some noise might be generated in the audio signal. Also, the transition of normal to undefined data and undefined or zero data to normal creates a data discontinuity in the digital output, which can generate some noise in the audio signal. 19 PCM1802 www.ti.com SLES023C – DECEMBER 2001 – REVISED JANUARY 2005 It is recommended to set PDWN low to get stable analog performance when the sampling rate, interface mode, data format, or oversampling control is changed. Synchronization Lost State of Synchronization SYNCHRONOUS Resynchronization ASYNCHRONOUS SYNCHRONOUS 1/fS DOUT NORMAL DATA 32/fS UNDEFINED DATA ZERO DATA NORMAL DATA T0020-05 Figure 28. ADC Digital Output for Loss of Synchronization and Resynchronization Power Down, HPF Bypass, Oversampling Control PDWN (pin 7) controls the entire ADC operation. During power-down mode, both the supply current for the analog portion and the clock signal for the digital portion are shut down, and power dissipation is minimized. Also, DOUT (pin 12) is disabled and no system clock is accepted during power-down mode. Power-Down Control PDWN MODE LOW Power-down mode HIGH Normal operation mode The built-in function for dc component rejection can be bypassed using the BYPAS (pin 8) control. In bypass mode, the dc components of the analog input signal, internal dc offset, etc., are also converted and included in the digital output data. HPF Bypass Control BYPAS HPF (HIGH-PASS FILTER) MODE LOW Normal (no dc component on DOUT) mode HIGH Bypass (dc component on DOUT) mode OSR (pin 16) controls the oversampling ratio of the delta-sigma modulator, ×64 or ×128. The ×128 mode is available for fS < 50 kHz, and must be used carefully as performance is affected by the duty cycle of the 384 fS system clock. Oversampling Control OSR 20 OVERSAMPLING RATIO LOW ×64 HIGH ×128 (fS < 50 kHz) PCM1802 www.ti.com SLES023C – DECEMBER 2001 – REVISED JANUARY 2005 APPLICATION INFORMATION Typical Circuit Connection Diagram Figure 29 illustrates a typical circuit connection diagram in which the cutoff frequency of the input HPF is about 8 Hz. L-Ch IN R-Ch IN C1(1) + C2(1) + VINL MODE1 20 2 VINR MODE0 19 3 VREF1 FMT1 18 Mode [1:0] C5(3) C6(4) 1 + FMT0 17 OSR 16 Oversampling AGND SCKI 15 System Clock 7 PDWN VDD 14 8 BYPAS DGND 13 9 FSYNC DOUT 12 Data Out BCK 11 Data Clock 4 VREF2 5 VCC 6 Power Down LCF Bypass R1(5) 5V 0V + Control Format [1:0] + C4(2) PCM1802 Control 10 LRCK + 3.3 V C3(2) 0V L/R Clock Audio Data Processor Frame Sync. S0026-02 (1) C1, C2: A 1-µF capacitor gives 8-Hz (τ = 1 µF × 20 kΩ) cutoff frequency for input HPF in normal operation and requires a power-on settling time with a 20-ms time constant during the power-on initialization period. (2) C3, C4: Bypass capacitors, 0.1-µF ceramic and 10-µF tantalum, depending on layout and power supply (3) C5: 0.1-µF ceramic and 10-µF tantalum capacitors are recommended. (4) C6: 0.1-µF ceramic and 10-µF tantalum capacitors are recommended when using a noisy analog power supply. These capacitor are not required for a clean analog supply. (5) R1: A 1-kΩ resistor is recommended when using a noisy analog power supply. This resistor is shorted for a clean analog supply. Figure 29. Typical Circuit Connection 21 PCM1802 SLES023C – DECEMBER 2001 – REVISED JANUARY 2005 www.ti.com APPLICATION INFORMATION (continued) Board Design and Layout Considerations VCC, VDD Pins The digital and analog power supply lines to the PCM1802 should be bypassed to the corresponding ground pins with 0.1-µF ceramic and 10-µF tantalum capacitors as close to the pins as possible to maximize the dynamic performance of the ADC. AGND, DGND Pins To maximize the dynamic performance of the PCM1802, the analog and digital grounds are not connected internally. These grounds should have low impedance to avoid digital noise feeding back into the analog ground. They should be connected directly to each other under the parts to reduce the potential noise problem. VIN Pins A 1-µF capacitor is recommended as an ac-coupling capacitor, which gives an 8-Hz cutoff frequency. If a higher full-scale input voltage is required, it can be accommodated by adding only one series resistor to each VIN pin. VREF1 Pin A ceramic capacitor of 0.1 µF and an electrolytic capacitor of 10 µF are recommended between VREF1 and AGND to ensure low source impedance for the ADC references. These capacitors should be located as close as possible to the VREF1 pin to reduce dynamic errors on the ADC references. VREF2 Pin The differential voltage between VREF2 and AGND sets the analog input full-scale range. A ceramic capacitor of 0.1 µF and an electrolytic capacitor of 10 µF are recommended between VREF2 and AGND with the insertion of a 1-kΩ resistor between VCC and VREF2 when using a noisy analog power supply. These capacitors and resistor are not required for a clean analog supply. These capacitors should be located as close as possible to the VREF2 pin to reduce dynamic errors on the ADC references. Full-scale input level is affected by this 1-kΩ resistor, decreasing by 3%. DOUT Pin The DOUT pin has enough load drive capability, but locating a buffer near the PCM1802 and minimizing load capacitance is recommended if the DOUT line is long, in order to minimize the digital-analog crosstalk and maximize the dynamic performance of the ADC. System Clock The quality of the system clock can influence dynamic performance, as the PCM1802 operates based on the system clock. In slave mode, it may be necessary to consider the system-clock duty cycle, jitter, and the time difference between the system clock transition and the BCK or LRCK transition. 22 PACKAGE OPTION ADDENDUM www.ti.com 7-Jun-2010 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) PCM1802DB ACTIVE SSOP DB 20 65 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Request Free Samples PCM1802DBG4 ACTIVE SSOP DB 20 65 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Request Free Samples PCM1802DBR ACTIVE SSOP DB 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Purchase Samples PCM1802DBRG4 ACTIVE SSOP DB 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Purchase Samples PCM1802S1DB OBSOLETE SSOP DB 20 TBD Call TI Call TI Samples Not Available PCM1802S1DBG4 OBSOLETE SSOP DB 20 TBD Call TI Call TI Samples Not Available (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 7-Jun-2010 Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 13-Jun-2008 TAPE AND REEL INFORMATION *All dimensions are nominal Device PCM1802DBR Package Package Pins Type Drawing SSOP DB 20 SPQ Reel Reel Diameter Width (mm) W1 (mm) 2000 330.0 17.4 Pack Materials-Page 1 A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 8.5 7.6 2.4 12.0 16.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 13-Jun-2008 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) PCM1802DBR SSOP DB 20 2000 336.6 336.6 28.6 Pack Materials-Page 2 MECHANICAL DATA MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 28 PINS SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,25 0,09 8,20 7,40 5,60 5,00 Gage Plane 1 14 0,25 A 0°–ā8° 0,95 0,55 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 /E 12/01 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DLP® Products www.dlp.com Communications and Telecom www.ti.com/communications DSP dsp.ti.com Computers and Peripherals www.ti.com/computers Clocks and Timers www.ti.com/clocks Consumer Electronics www.ti.com/consumer-apps Interface interface.ti.com Energy www.ti.com/energy Logic logic.ti.com Industrial www.ti.com/industrial Power Mgmt power.ti.com Medical www.ti.com/medical Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Space, Avionics & Defense www.ti.com/space-avionics-defense RF/IF and ZigBee® Solutions www.ti.com/lprf Video and Imaging www.ti.com/video Wireless www.ti.com/wireless-apps Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2010, Texas Instruments Incorporated