DS92LV040A 4 Channel Bus LVDS Transceiver General Description Features The DS92LV040A is one in a series of Bus LVDS transceivers designed specifically for high speed, low power backplane or cable interfaces. The device operates from a single 3.3V power supply and includes four differential line drivers and four receivers. To minimize bus loading, the driver outputs and receiver inputs are internally connected. The device also features a flow through pin out which allows easy PCB routing for short stubs between its pins and the connector. The driver translates 3V LVTTL levels (single-ended) to differential Bus LVDS (BLVDS) output levels. This allows for high speed operation while consuming minimal power and reducing EMI. In addition, the differential signaling provides common mode noise rejection greater than ± 1V. The receiver threshold is less than +0/−70 mV. The receiver translates the differential Bus LVDS to standard (LVTTL/ LVCMOS) levels. (See Applications Information Section for more details.) n Bus LVDS Signaling n Propagation delay: Driver 2.3ns max, Receiver 3.2ns max n Low power CMOS design n 100% Transition time 1ns driver typical, 1.3ns receiver typical n High Signaling Rate Capability (above 155 Mbps) n 0.1V to 2.3V Common Mode Range for VID = 200mV n 70 mV Receiver Sensitivity n Supports open and terminated failsafe on port pins n 3.3V operation n Glitch free power up/down (Driver & Receiver disabled) n Light Bus Loading (5 pF typical) per Bus LVDS load n Designed for Double Termination Applications n Balanced Output Impedance n Product offered in 44 pin LLP (Leadless Leadframe Package) package n High impedance Bus pins on power off (VCC = 0V) Simplified Functional Diagram 10133601 © 2002 National Semiconductor Corporation DS101336 www.national.com DS92LV040A 4 Channel Bus LVDS Transceiver August 2002 DS92LV040A Absolute Maximum Ratings θja (Note 3) (Notes 1, 25.8˚C/W θjc 2) Supply Voltage (VCC) (Soldering, 4 sec.) 260˚C 4.0V Recommended Operating Conditions −0.3V to (VCC +0.3V) Driver Input Voltage (DIN) −65˚C to +150˚C Lead Temperature Enable Input Voltage (DE, RE) 25.5˚C/W Storage Temperature Range If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. −0.3V to (VCC +0.3V) Min Max Supply Voltage (VCC) 3.0 3.6 V Receiver Input Voltage 0.0 2.4 V ESD (Note 4) Operating Free Air Temperature −40 +85 ˚C (HBM 1.5 kΩ, 100 pF) Slowest Input Edge Rate Receiver Output Voltage (ROUT) −0.3V to (VCC +0.3V) Bus Pin Voltage (DO/RI ± ) −0.3V to +3.9V > 4kV > 250V Machine Model LLP(Note 3) 4.8 W Derate LLP Package ∆t/∆V (Note 7)(20% to 80%) Maximum Package Power Dissipation at 25˚C Units Data 1.0 ns/V Control 3.0 ns/V 38.8mW/˚C DC Electrical Characteristics Over recommended operating supply voltage and temperature ranges unless otherwise specified (Notes 2, 4) Symbol Parameter Conditions Pin Min Typ Max Units DO+/RI+, DO−/RI− 200 300 460 mV 5 27 mV 1.1 1.3 1.5 V 5 10 mV 1.4 1.65 V VOD Output Differential Voltage ∆VOD VOD Magnitude Change VOS Offset Voltage ∆VOS Offset Magnitude Change VOHD Driver Output High Voltage RL = 27Ω VOLD Driver Output Low Voltage RL = 27Ω IOSD Driver Output Short Circuit Current (Note 11) VOD = 0V, DE = VCC, Driver outputs shorted together VOHR Receiver Voltage Output High (Note 12) VCC−0.2 V Inputs Open VCC−0.2 V Inputs Terminated, RL = 27Ω VCC−0.2 V VOLR Receiver Voltage Output Low IOD Receiver Output Dynamic Current (Note 11) VTH Input Threshold High (Note 9) VTL Input Threshold Low (Note 9) VCMR Receiver Common Mode Range IIN Input Current www.national.com RL = 27Ω, Figure 1 VID = +300 mV 0.95 IOH = −4 mA |30| ROUT IOL = 4.0 mA, VID = −300 mV 0.05 VID = 300mV, VOUT = VCC−1.0V −50 VID = −300mV, VOUT = 1.0V DE = 0V, Over common mode range 1.1 DO+/RI+, DO−/RI− −70 V | 45| 0.100 |33| mA V mA |36| 60 mA −40 0 mV −40 |VID|/2 mV 2.4 − |VID|/2 V DE = 0V, RE = 2.4V, VIN = +2.4V or 0V −20 ±1 +20 µA VCC = 0V, VIN = +2.4V or 0V −20 ±1 +20 µA 2 (Continued) Over recommended operating supply voltage and temperature ranges unless otherwise specified (Notes 2, 4) Symbol Parameter Conditions Pin Min Typ Max Units 2.0 VCC V GND 0.8 V +20 µA +20 µA VIH Minimum Input High Voltage VIL Maximum Input Low Voltage IIH Input High Current VIN = VCC or 2.4V −20 IIL Input Low Current VIN = GND or 0.4V −20 ± 2.5 ± 2.5 VCL Input Diode Clamp Voltage ICLAMP = −18 mA −1.5 −0.8 ICCD Power Supply Current Drivers Enabled, Receivers Disabled No Load, DE = RE = VCC, DIN = VCC or GND Power Supply Current Drivers Disabled, Receivers Enabled DE = RE = 0V, VID = ± 300mV Power Supply Current, Drivers and Receivers TRI-STATE DE = 0V; RE = VCC, DIN = VCC or GND Power Supply Current, Drivers and Receivers Enabled DE = VCC; RE = 0V, DIN = VCC or GND, RL = 27Ω Power Off Leakage Current VCC = 0V or OPEN, DIN, DE, RE = 0V or OPEN, VAPPLIED = 3.6V (Port Pins) ICCR ICCZ ICC IOFF DIN, DE, RE V VCC DO+/RI+, DO−/RI− 20 40 mA 27 40 mA 28 40 mA 70 100 mA +20 µA −20 COUTPUT Capacitance @ Bus Pins DO+/RI+, DO−/RI− 5 pF cOUTPUT Capacitance @ ROUT ROUT 5 pF AC Electrical Characteristics Over recommended operating supply voltage and temperature ranges unless otherwise specified (Note 7) Symbol Parameter Conditions Min Typ Max Units DIFFERENTIAL DRIVER TIMING REQUIREMENTS tPHLD Differential Prop. Delay High to Low (Note 9) tPLHD Differential Prop. Delay Low to High (Note 9) tSKD1 Differential Skew |tPHLD–tPLHD| (duty cycle)(Note 10), (Note 9) RL = 27Ω, Figures 2, 3, CL = 10 pF 1.0 1.5 2.3 ns 1.0 1.5 2.3 ns 80 160 ps tCCSK Channel to Channel Skew (all 4 channels), (Note 9) 220 400 ps tTLH Transition Time Low to High (20% to 80%) 0.4 0.75 1.3 ns tTHL Transition Time High to Low (80% to 20%) 0.4 0.75 1.3 ns tPHZ Disable Time High to Z 5.0 10 ns tPLZ Disable Time Low to Z 5.0 10 ns tPZH Enable Time Z to High 5.0 10 ns tPZL Enable Time Z to Low 5.0 10 ns fMAXD Guaranteed operation per data sheet up to the Min. Duty Cycle 45/55%,Transition time ≤ 25% of period (Note 9) RL = 27Ω, Figures 4, 5, CL = 10 pF 85 3 125 MHz www.national.com DS92LV040A DC Electrical Characteristics DS92LV040A AC Electrical Characteristics (Continued) Over recommended operating supply voltage and temperature ranges unless otherwise specified (Note 7) Symbol Parameter Conditions Min Typ Max Units DIFFERENTIAL RECEIVER TIMING REQUIREMENTS tPHLDR Differential Prop. Delay High to Low (Note 9) tPLHDR Differential Prop Delay Low to High (Note 9) tSDK1R Differential Skew |tPHLD–tPLHD| (duty cycle)(Note 10), (Note 9) Figures 6, 7, CL = 15 pF tCCSKR Channel to Channel Skew (all 4 channels)(Note 9) tTLHR Transition Time Low to High (10% to 90%) (Note 9) tTHLR Transition Time High to Low (90% to 10%) (Note 9) tPHZ Disable Time High to Z tPLZ Disable Time Low to Z tPZH Enable Time Z to High tPZL Enable Time Z to Low fMAXR Guaranteed operation per data sheet up to the Min. Duty Cycle 45/55%,Transition time ≤ 25% of period (Note 9) 1.6 2.4 3.2 ns 1.6 2.4 3.2 ns 85 160 ps 140 300 ps 0.850 1.250 2.0 ns 0.850 1.030 2.0 ns 3.0 10 ns 3.0 10 ns 3.0 10 ns 3.0 10 ns RL = 500Ω, Figures 8, 9, CL = 15 pF 85 125 MHz Note 1: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The table of “Electrical Characteristics” provides conditions for actual device operation. Note 2: All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to ground unless otherwise specified except VOD, ∆VOD and VID. Note 3: Package must be mounted to pc board in accordance with AN-1187 to achieve thermals. Note 4: All typicals are given for VCC = +3.3V and TA = +25˚C, unless otherwise stated. Note 5: ESD Rating: HBM (1.5 kΩ, 100 pF) > 4 kV EIAJ (0Ω, 200 pF) > 250. Note 6: CL includes probe and fixture capacitance. Note 7: Generator waveforms for all tests unless otherwise specified: f = 25 MHz, ZO = 50Ω, tr, tf = < 1.0 ns (0%–100%). To ensure fastest propagation delay and minimum skew, data input edge rates should be equal to or faster than 1ns/V; control signals equal to or faster than 3ns/V. In general, the faster the input edge rate, the better the AC performance. Note 8: The DS92LV040A functions within datasheet specification when a resistive load is applied to the driver outputs. Note 9: Propagation delays, transition times, and receiver threshold are guaranteed by design and characterization. Note 10: tSKD1 |tPHLD–tPLHD| is the worst case pulse skew (measure of duty cycle) over recommended operation conditions. Note 11: Only one output at a time should be shorted, do not exceed maximum package power dissipation capacity. Note 12: VOH fail-safe terminated test performed with 27Ω connected between RI+ and RI− inputs. No external voltage is applied. Note 13: Chip to Chip skew is the difference in differential propagation delay between any channels of any devices, either edge. function of load resistor. The current mode requires (as discussed above) that a resistive termination be employed to terminate the signal and to complete the loop. Unterminated configurations are not allowed. The 12 mA loop current will develop a differential voltage of about 300mV across a 27Ω (double terminated 54Ω differential transmission backplane) effective resistance, which the receiver detects with a 230 mV minimum differential noise margin neglecting resistive line losses (driven signal minus receiver threshold (300 mV – 70 mV = 230 mV)). The signal is centered around +1.2V (Driver Offset, VOS ) with respect to ground. Note that the steady-state voltage (VSS ) peak-to-peak swing is twice the differential voltage (VOD ) and is typically 600 mV. The current mode driver provides substantial benefits over voltage mode drivers, such as an RS-422 driver. Its quiescent current remains relatively flat versus switching frequency. Whereas the RS-422 voltage mode driver increases exponentially in most case between 20 MHz–50 MHz. This is due to the overlap current that flows between the rails of the device when the internal gates switch. Whereas the current mode driver switches a fixed current between its output without any substantial overlap current. This is similar to some ECL and PECL devices, but without the heavy static ICC requirements of the ECL/PECL designs. LVDS requires 80% less current than similar PECL devices. AC specifications for the driver are a tenfold improvement over other Applications Information General application guidelines and hints may be found in the following application notes: AN-808, AN-977, AN-971, and AN-903. BLVDS drivers and receivers are intended to be used in a differential backplane configuration. Transceivers or receivers are connected to the driver through a balanced media such as differential PCB traces. Typically, the characteristic differential impedance of the media (Zo) is in the range of 50Ω to 100Ω. Two termination resistors of ZoΩ each are placed at the ends of the transmission line backplane. The termination resistor converts the current sourced by the driver into a voltage that is detected by the receiver. The effects of mid-stream connector(s), cable stub(s), and other impedance discontinuity as well as ground shifting, noise margin limits, and total termination loading must be taken into account. The DS92LV040A differential line driver is a balanced current mode design. A current mode driver, generally speaking has a high output impedance (100 ohms) and supplies a reasonably constant current for a range of loads (a voltage mode driver on the other hand supplies a constant voltage for a range of loads). Current is switched through the load in one direction to produce a logic state and in the other direction to produce the other logic state. The output current is typically 12 mA. The current changes as a www.national.com 4 traces 3mm apart since magnetic field cancellation is much better with the closer traces. Plus, noise induced on the differential lines is much more likely to appear as common-mode which is rejected by the receiver. Match electrical lengths between traces to reduce skew. Skew between the signals of a pair means a phase difference between signals which destroys the magnetic field cancellation benefits of differential signals and EMI will result. (Note the velocity of propagation, v = c/Er where c (the speed of light) = 0.2997mm/ps or 0.0118 in/ps). Do not rely solely on the autoroute function for differential traces. Carefully review dimensions to match differential impedance and provide isolation for the differential lines. Minimize the number of vias and other discontinuity on the line. Avoid 90˚ turns (these cause impedance discontinuity). Use arcs or 45˚ bevels. Within a pair of traces, the distance between the two traces should be minimized to maintain common-mode rejection of the receivers. On the printed circuit board, this distance should remain constant to avoid discontinuity in differential impedance. Minor violations at connection points are allowable. • Stub Length: Stub lengths should be kept to a minimum. The typical transition time of the DS92LV040A BLVDS output is 0.75ns (20% to 80%). The extrapolated 100 percent time is 0.75/0.6 or 1.25ns. For a general approximation, if the electrical length of a trace is greater than 1/5 of the transition edge, then the trace is considered a transmission line. For example, 1.25ns/5 is 250 picoseconds. Let velocity equal 160ps per inch for a typical loaded backplane. Then maximum stub length is 250ps/ 160ps/in or 1.56 inches. To determine the maximum stub for your backplane, you need to know the propagation velocity for the actual conditions (refer to application notes AN 905 and AN 808). PACKAGE and SOLDERING INFORMATION: • Refer to packaging application note AN-1187. This application note details the package attachment methods to achieve the correct solderability and thermal results. (Continued) existing RS-422 drivers. The TRI-STATE function allows the driver outputs to be disabled, thus obtaining an even lower power state when the transmission of data is not required. There are a few common practices which should be implied when designing PCB for Bus LVDS signaling. Recommended practices are: • Use at least 4 PCB board layer (Bus LVDS signals, ground, power and TTL signals). • Keep drivers and receivers as close to the (Bus LVDS port side) connector as possible. • Bypass each Bus LVDS device and also use distributed bulk capacitance between power planes. Surface mount capacitors placed close to power and ground pins work best. Three or more high frequency, multi-layer ceramic (MLC) surface mount (0.1 µF, 0.01 µF, 0.001 µF) in parallel should be used between each VCC and ground. Multiple vias should be used to connect VCC and Ground planes to the pads of the by-pass capacitors. In addition, it may be necessary to randomly distribute by-pass capacitors of different values (200pF to 1000pF) to achieve different resonant frequencies. • Use the termination resistor which best matches the differential impedance of your transmission line. • Leave unused Bus LVDS receiver inputs open (floating). Limit traces on unused inputs to < 0.5 inches. • Isolate TTL signals from Bus LVDS signals MEDIA (CONNECTOR or BACKPLANE) SELECTION: • The backplane and connectors should have a matched differential impedance. Use controlled impedance traces which match the differential impedance of your transmission medium (ie. backplane or cable) and termination resistor(s). Run the differential pair trace lines as close together as possible as soon as they leave the IC . This will help eliminate reflections and ensure noise is coupled as common-mode. In fact, we have seen that differential signals which are 1mm apart radiate far less noise than 5 www.national.com DS92LV040A Applications Information DS92LV040A Applications Information (Continued) TABLE 1. Functional Table MODE SELECTED DE RE DRIVER MODE H H RECEIVER MODE L L TRI-STATE™ MODE L H LOOP BACK MODE H L TABLE 2. Transmitter Mode INPUTS DE OUTPUTS DIN DO+ DO− H H L L H H H L H 0.8V < DIN < 2.0V X X L X Z Z TABLE 3. Receiver Mode INPUTS OUTPUT RE (RI+) – (RI−) L L ( < −70 mV) L L H ( > 0 mV) H L −70 mV < VID < 0 mV X H X Z X = High or Low logic state L = Low state Z = High impedance state H = High state Test Circuits and Timing Waveforms 10133603 FIGURE 1. Differential Driver DC Test Circuit www.national.com 6 DS92LV040A Test Circuits and Timing Waveforms (Continued) 10133604 FIGURE 2. Differential Driver Propagation Delay and Transition Time Test Circuit 10133605 FIGURE 3. Differential Driver Propagation Delay and Transition Time Waveforms 10133606 FIGURE 4. Driver TRI-STATE Delay Test Circuit 7 www.national.com DS92LV040A Test Circuits and Timing Waveforms (Continued) 10133607 FIGURE 5. Driver TRI-STATE Delay Waveforms 10133608 FIGURE 6. Receiver Propagation Delay and Transition Time Test Circuit 10133609 FIGURE 7. Receiver Propagation Delay and Transition Time Waveforms 10133610 FIGURE 8. Receiver TRI-STATE Delay Test Circuit www.national.com 8 DS92LV040A Test Circuits and Timing Waveforms (Continued) 10133611 FIGURE 9. Receiver TRI-STATE Delay Waveforms Typical Bus Application Configurations 10133612 Bidirectional Half-Duplex Point-to-Point Applications 10133613 Multi-Point Bus Applications 9 www.national.com DS92LV040A Connection Diagram 10133602 Top View Order Number DS92LV040ATLQA See NS Package Number LQA44A www.national.com 10 Pin Name Pin # Input/Output DO+/RI+ 14, 16, 19, 21 I/O True Bus LVDS Driver Outputs and Receiver Inputs. DO−/RI− 13, 15, 18, 20 I/O Complimentary Bus LVDS Driver Outputs and Receiver Inputs. DIN 35, 37, 40, 42 I LVTTL Driver Input. No pull up or pull down is attached to this pin RO 36, 38, 41, 43 O LVTTL Receiver Output. RE12 29 I Receiver Enable LVTTL Input (Active Low). This pin, when low, configures receiver outputs, RO1 and RO2 active. When this pin is high, RO1 and RO2 are TRI-STATE. If this pin is floating, a weak current source to VCC causes RO1 and RO2 to be TRI-STATE RE34 5 I Receiver Enable LVTTL Input (Active Low). This pin, when low, configures receiver outputs, RO3 and RO4 active. When this pin is high, RO3 and RO4 are TRI-STATE. If this pin is floating, a weak current source to VCC causes RO3 and RO4 to be TRI-STATE DE12 26 I Driver Enable LVTTL Input (Active High). This pin, when high, configures driver outputs, DO1+/RIN1+, DO1−/RIN1− and DO2+/RIN2+, DO2−/RIN2− active. When this pin is low, driver outputs 1 and 2 are TRI-STATE. If this pin is floating, a weak current source to VCC causes driver outputs 1 and 2 to be active DE34 8 I Driver Enable LVTTL Input (Active High). This pin, when high, configures driver outputs, DO3+/RIN3+, DO3−/RIN3− and DO4+/RIN4+, DO4−/RIN4− active. When this pin is low, driver outputs 3 and 4 are TRI-STATE. If this pin is floating, a weak current source to VCC causes driver outputs 3 and 4 to be active GND 4, 28, 31, 39 Ground Ground for digital circuitry (must connect to GND on PC board). These pins connected internally. VCC 3, 6, 30 Power VCC for digital circuitry (must connect to VCC on PC board). These pins connected internally. AGND 9, 17, 25 Ground Ground for analog circuitry (must connect to GND on PC board). These pins connected internally. AVCC 7, 10, 22, 27 Power Analog VCC (must connect to VCC on PC board). These pins connected internally. NC 1, 2, 11, 12, 23, 24, 32, 33, 34, 44 N/A Reserved for future use, leave open circuit. GND Must connect to GND plane through vias to achieve the theta ja specified under Absolute Maximum Ratings. The DAP (die attach pad) is the heat transfer material that is centered on the bottom of the LLP package. Refer to application note AN-1187 for attachment details. DAP Descriptions 11 www.national.com DS92LV040A Pinout Description DS92LV040A 4 Channel Bus LVDS Transceiver Physical Dimensions All dimensions are in millimeters Physical Dimensions inches (millimeters) unless otherwise noted 44 pin Plastic LLP Package Order Number DS92LV040ATLQA NS Package Number LQA44A LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Email: [email protected] www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: [email protected] National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.