NSC DS90LV031B

DS90LV031B
3V LVDS Quad CMOS Differential Line Driver
General Description
Features
The DS90LV031B is a quad CMOS differential line driver
designed for applications requiring ultra low power dissipation and high data rates. The device is designed to support
data rates in excess of 400 Mbps (200 MHz) utilizing Low
Voltage Differential Signaling (LVDS) technology.
The DS90LV031B accepts low voltage TTL/CMOS input levels and translates them to low voltage (350 mV) differential
output signals. In addition the driver supports a TRI-STATE ®
function that may be used to disable the output stage, disabling the load current, and thus dropping the device to an
ultra low idle power state of 13 mW typical. The
DS90LV031B is enhanced over the DS90LV031A in that the
inputs are further ruggedized for excessive undershoot.
The EN and EN* inputs allow active Low or active High
control of the TRI-STATE outputs. The enables are common
to all four drivers. The DS90LV031B and companion line
receiver (DS90LV032A) provide a new alternative to high
power pseudo-ECL devices for high speed point-to-point
interface applications.
n
n
n
n
n
Connection Diagram
n
n
n
n
n
n
n
n
> 400 Mbps (200 MHz) switching rates
0.1 ns typical differential skew
0.4 ns maximum differential skew
2.0 ns maximum propagation delay
Ruggedized inputs that can withstand excessive
undershoot
3.3V power supply design
± 350 mV differential signaling
Low power dissipation (13mW at 3.3V static)
Interoperable with existing 5V LVDS devices
Compatible with IEEE 1596.3 SCI LVDS standard
Compatible with TIA/EIA-644 LVDS standard
Industrial temperature operating range
Available in SOIC surface mount packaging
Functional Diagram
Dual-In-Line
10131101
Order Number DS90LV031BTM
See NS Package Number M16A
Truth Table
DRIVER
Enables
Input
Outputs
EN
EN*
DIN
DOUT+
DOUT−
L
H
X
Z
Z
L
L
H
H
H
L
All other combinations of
ENABLE inputs
10131102
TRI-STATE ® is a registered trademark of National Semiconductor Corporation.
© 2005 National Semiconductor Corporation
DS101311
www.national.com
DS90LV031B 3V LVDS Quad CMOS Differential Line Driver
January 2005
DS90LV031B
Absolute Maximum Ratings (Note 1)
Lead Temperature Range
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Maximum Junction
Temperature
Supply Voltage (VCC)
Soldering (4 sec.)
−0.3V to +4V
Input Voltage (DIN)(Note 2)
−0.6V to (VCC + 0.3V)
Enable Input Voltage (EN,
EN*)(Note 2)
−0.6V to (VCC + 0.3V)
+150˚C
ESD Rating
≥ 7 kV
(HBM, 1.5 kΩ, 100 pF)
(EIAJ, 0 Ω, 200 pF)
Output Voltage (DOUT+,
DOUT−)(Note 2)
−0.6V to +3.9V
(DOUT+, DOUT−)
Recommended Operating
Conditions
Continuous
Min
Typ
Max
Supply Voltage (VCC)
+3.0
+3.3
+3.6
V
Operating Free Air
Temperature (TA)
−40
+25
+85
˚C
Maximum Package Power Dissipation @ +25˚C
M Package
1088 mW
8.5 mW/˚C above +25˚C
Storage Temperature Range
≥ 500 V
≥ 1250 V
(CDM)
Short Circuit Duration
Derate M Package
+260˚C
−65˚C to +150˚C
Units
Electrical Characteristics
Over supply voltage and operating temperature ranges, unless otherwise specified. (Notes 3, 4, 5)
Symbol
Parameter
Conditions
Pin
Min
Typ
Max
DOUT−
DOUT+
250
350
450
mV
4
35
|mV|
1.25
1.375
V
5
25
|mV|
1.38
1.6
V
VOD1
Differential Output Voltage
∆VOD1
Change in Magnitude of VOD1 for
Complementary Output States
VOS
Offset Voltage
∆VOS
Change in Magnitude of VOS for
Complementary Output States
VOH
Output Voltage High
VOL
Output Voltage Low
VIH
Input Voltage High
VIL
Input Voltage Low
IIH
Input Current
IIL
Input Current
VIN = GND or 0.4V
−10
±1
±1
VCL
Input Clamp Voltage
ICL = −18 mA
−1.5
−0.8
IOS
Output Short Circuit Current
ENABLED, (Note 11)
DIN = VCC, DOUT+ = 0V or
DIN = GND, DOUT− = 0V
IOSD
Differential Output Short Circuit
Current
ENABLED, VOD = 0V (Note 11)
IOFF
Power-off Leakage
VOUT = 0V or 3.6V,
VCC = 0V or Open
IOZ
Output TRI-STATE Current
EN = 0.8V and EN* = 2.0V
VOUT = 0V or VCC
ICC
No Load Supply Current Drivers
Enabled
DIN = VCC or GND
ICCL
Loaded Supply Current Drivers
Enabled
ICCZ
No Load Supply Current Drivers
Disabled
www.national.com
RL = 100Ω (Figure 1)
1.125
0.90
1.03
V
2.0
VCC
V
GND
0.8
V
+10
µA
+10
µA
−6.0
−9.0
mA
−6.0
−9.0
mA
−20
±1
+20
µA
−10
±1
+10
µA
5.0
8.0
mA
RL = 100Ω All Channels,
DIN = VCC or GND (all inputs)
23
30
mA
DIN = VCC or GND,
EN = GND, EN* = VCC
2.6
6.0
mA
VIN = VCC or 2.5V
2
DIN,
EN,
EN*
Units
−10
DOUT−
DOUT+
VCC
V
Over supply voltage and operating temperature ranges, unless otherwise specified. (Notes 4, 10, 12)
Symbol
Parameter
Conditions
Min
Typ
Max
Units
0.8
1.18
2.0
ns
0.8
1.25
2.0
ns
0
0.07
0.4
ns
Channel-to-Channel Skew (Note 7)
0
0.1
0.5
ns
Differential Part to Part Skew (Note 8)
0
1.0
ns
tSKD4
Differential Part to Part Skew (Note 9)
0
1.2
ns
tTLH
Rise Time
0.38
1.5
ns
tTHL
Fall Time
0.40
1.5
ns
5
ns
5
ns
tPHLD
Differential Propagation Delay High to Low
tPLHD
Differential Propagation Delay Low to High
tSKD1
Differential Pulse Skew |tPHLD − tPLHD|
(Note 6)
tSKD2
tSKD3
RL = 100Ω, CL = 10 pF
(Figure 2 and Figure 3)
tPHZ
Disable Time High to Z
tPLZ
Disable Time Low to Z
tPZH
Enable Time Z to High
7
ns
tPZL
Enable Time Z to Low
7
ns
fMAX
Maximum Operating Frequency (Note 14)
RL = 100Ω, CL = 10 pF
(Figure 4 and Figure 5)
200
250
MHz
Note 1: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices
should be operated at these limits. The table of “Electrical Characteristics” specifies conditions of device operation.
Note 2: These ABS-MAX voltage ratings are guaranteed by design and bench characterization. The pin under test is pulled negative with respect to ground, using
a curve tracer. During the test, ICC and the current out of the pin under test are monitored using DC meters.
Note 3: Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground except: VOD1 and
∆VOD1.
Note 4: All typicals are given for: VCC = +3.3V, TA = +25˚C.
Note 5: The DS90LV031B is a current mode device and only functions within datasheet specifications when a resistive load is applied to the driver outputs typical
range is (90Ω to 110Ω)
Note 6: tSKD1, |tPHLD − tPLHD| is the magnitude difference in differential propagation delay time between the positive going edge and the negative going edge of the
same channel.
Note 7: tSKD2 is the Differential Channel-to-Channel Skew of any event on the same device.
Note 8: tSKD3, Differential Part to Part Skew, is defined as the difference between the minimum and maximum specified differential propagation delays. This
specification applies to devices at the same VCC and within 5˚C of each other within the operating temperature range.
Note 9: tSKD4, part to part skew, is the differential channel-to-channel skew of any event between devices. This specification applies to devices over recommended
operating temperature and voltage ranges, and across process distribution. tSKD4 is defined as |Max − Min| differential propagation delay.
Note 10: Generator waveform for all tests unless otherwise specified: f = 1 MHz, ZO = 50Ω, tr ≤ 1 ns, and tf ≤ 1 ns.
Note 11: Output short circuit current (IOS) is specified as magnitude only, minus sign indicates direction only.
Note 12: CL includes probe and jig capacitance.
Note 13: All input voltages are for one channel unless otherwise specified. Other inputs are set to GND.
Note 14: fMAX generator input conditions: tr = tf < 1ns, (0% to 100%), 50% duty cycle, 0V to 3V. Output Criteria: duty cycle = 45%/55%, VOD > 250mV, all channels
switching.
Parameter Measurement
Information
10131103
FIGURE 1. Driver VOD and VOS Test Circuit
3
www.national.com
DS90LV031B
Switching Characteristics - Industrial
DS90LV031B
Parameter Measurement Information
(Continued)
10131104
FIGURE 2. Driver Propagation Delay and Transition Time Test Circuit
10131105
FIGURE 3. Driver Propagation Delay and Transition Time Waveforms
10131106
FIGURE 4. Driver TRI-STATE Delay Test Circuit
www.national.com
4
DS90LV031B
Parameter Measurement Information
(Continued)
10131107
FIGURE 5. Driver TRI-STATE Delay Waveform
Typical Application
10131108
FIGURE 6. Point-to-Point Application
The DS90LV031B differential line driver is a balanced current source design. A current mode driver, generally speaking has a high output impedance and supplies a constant
current for a range of loads (a voltage mode driver on the
other hand supplies a constant voltage for a range of loads).
Current is switched through the load in one direction to
produce a logic state and in the other direction to produce
the other logic state. The output current is typically 3.5 mA, a
minimum of 2.5 mA, and a maximum of 4.5 mA. The current
mode requires (as discussed above) that a resistive termination be employed to terminate the signal and to complete
the loop as shown in Figure 6. AC or unterminated configurations are not allowed. The 3.5 mA loop current will develop
a differential voltage of 350 mV across the 100Ω termination
resistor which the receiver detects with a 250 mV minimum
differential noise margin neglecting resistive line losses
(driven signal minus receiver threshold (350 mV – 100 mV =
250 mV)). The signal is centered around +1.2V (Driver Offset, VOS) with respect to ground as shown in Figure 7. Note
that the steady-state voltage (VSS) peak-to-peak swing is
twice the differential voltage (VOD) and is typically 700 mV.
The current mode driver provides substantial benefits over
voltage mode drivers, such as an RS-422 driver. Its quiescent current remains relatively flat versus switching fre-
Applications Information
General application guidelines and hints for LVDS drivers
and receivers may be found in the following application
notes: LVDS Owner’s Manual (lit #550062-001), AN808,
AN977, AN971, AN916, AN805, AN903.
LVDS drivers and receivers are intended to be primarily used
in an uncomplicated point-to-point configuration as is shown
in Figure 6. This configuration provides a clean signaling
environment for the quick edge rates of the drivers. The
receiver is connected to the driver through a balanced media
which may be a standard twisted pair cable, a parallel pair
cable, or simply PCB traces. Typically, the characteristic
differential impedance of the media is in the range of 100Ω.
A termination resistor of 100Ω should be selected to match
the media, and is located as close to the receiver input pins
as possible. The termination resistor converts the current
sourced by the driver into a voltage that is detected by the
receiver. Other configurations are possible such as a multireceiver configuration, but the effects of a mid-stream connector(s), cable stub(s), and other impedance discontinuities
as well as ground shifting, noise margin limits, and total
termination loading must be taken into account.
5
www.national.com
DS90LV031B
Applications Information
Within a pair of traces, the distance between the two traces
should be minimized to maintain common-mode rejection of
the receivers. On the printed circuit board, this distance
should remain constant to avoid discontinuities in differential
impedance. Minor violations at connection points are allowable.
(Continued)
quency. Whereas the RS-422 voltage mode driver increases
exponentially in most case between 20 MHz–50 MHz. This
is due to the overlap current that flows between the rails of
the device when the internal gates switch. Whereas the
current mode driver switches a fixed current between its
output without any substantial overlap current. This is similar
to some ECL and PECL devices, but without the heavy static
ICC requirements of the ECL/PECL designs. LVDS requires
about 80% less current than similar PECL devices. AC specifications for the driver are a tenfold improvement over other
existing RS-422 drivers.
The TRI-STATE function allows the driver outputs to be
disabled, thus obtaining an even lower power state when the
transmission of data is not required.
The footprint of the DS90LV031B is the same as the industry
standard 26LS31 Quad Differential (RS-422) Driver and is a
step down replacement for the 5V DS90C031 Quad Driver.
TERMINATION
Use a resistor which best matches the differential impedance
or your transmission line. The resistor should be between
90Ω and 130Ω. Remember that the current mode outputs
need the termination resistor to generate the differential
voltage. LVDS will not work without resistor termination.
Typically, connect a single resistor across the pair at the
receiver end.
Surface mount 1% to 2% resistors are best. PCB stubs,
component lead, and the distance from the termination to the
receiver inputs should be minimized. The distance between
the termination resistor and the receiver should be < 10mm
(12mm MAX).
POWER DECOUPLING RECOMMENDATIONS
PROBING LVDS TRANSMISSION LINES
Always use high impedance ( > 100kΩ), low capacitance
( < 2pF) scope probes with a wide bandwidth (1GHz) scope.
Improper probing will give deceiving results.
Bypass capacitors must be used on power pins. High frequency ceramic (surface mount is recommended) 0.1µF in
parallel with 0.01µF, in parallel with 0.001µF at the power
supply pin as well as scattered capacitors over the printed
circuit board. Multiple vias should be used to connect the
decoupling capacitors to the power planes. A 10µF (35V) or
greater solid tantalum capacitor should be connected at the
power entry point on the printed circuit board.
CABLES AND CONNECTORS, GENERAL COMMENTS
When choosing cable and connectors for LVDS it is important to remember:
Use controlled impedance media. The cables and connectors you use should have a matched differential impedance
of about 100Ω. They should not introduce major impedance
discontinuities.
Balanced cables (e.g. twisted pair) are usually better than
unbalanced cables (ribbon cable, simple coax.) for noise
reduction and signal quality. Balanced cables tend to generate less EMI due to field canceling effects and also tend to
pick up electromagnetic radiation a common-mode (not differential mode) noise which is rejected by the receiver. For
cable distances < 0.5M, most cables can be made to work
effectively. For distances 0.5M ≤ d ≤ 10M, CAT 3 (category 3)
twisted pair cable works well, is readily available and relatively inexpensive.
PC BOARD CONSIDERATIONS
Use at least 4 PCB layers (top to bottom); LVDS signals,
ground, power, TTL signals.
Isolate TTL signals from LVDS signals, otherwise the TTL
may couple onto the LVDS lines. It is best to put TTL and
LVDS signals on different layers which are isolated by a
power/ground plane(s).
Keep drivers and receivers as close to the (LVDS port side)
connectors as possible.
DIFFERENTIAL TRACES
Use controlled impedance traces which match the differential impedance of your transmission medium (ie. cable) and
termination resistor. Run the differential pair trace lines as
close together as possible as soon as they leave the IC
(stubs should be < 10mm long). This will help eliminate
reflections and ensure noise is coupled as common-mode.
In fact, we have seen that differential signals which are 1mm
apart radiate far less noise than traces 3mm apart since
magnetic field cancellation is much better with the closer
traces. Plus, noise induced on the differential lines is much
more likely to appear as common-mode which is rejected by
the receiver.
Match electrical lengths between traces to reduce skew.
Skew between the signals of a pair means a phase difference between signals which destroys the magnetic field
cancellation benefits of differential signals and EMI will result. (Note the velocity of propagation, v = c/Er where c (the
speed of light) = 0.2997mm/ps or 0.0118 in/ps). Do not rely
solely on the autoroute function for differential traces. Carefully review dimensions to match differential impedance and
provide isolation for the differential lines. Minimize the number or vias and other discontinuities on the line.
Avoid 90˚ turns (these cause impedance discontinuities).
Use arcs or 45˚ bevels.
www.national.com
FAIL-SAFE FEATURE
The LVDS receiver is a high gain, high speed device that
amplifies a small differential signal (20mV) to CMOS logic
levels. Due to the high gain and tight threshold of the receiver, care should be taken to prevent noise from appearing
as a valid signal.
The receiver’s internal fail-safe circuitry is designed to
source/sink a small amount of current, providing fail-safe
protection (a stable known state of HIGH output voltage) for
floating, terminated or shorted receiver inputs.
1. Open Input Pins. The DS90LV032A is a quad receiver
device, and if an application requires only 1, 2 or 3
receivers, the unused channel(s) inputs should be left
OPEN. Do not tie unused receiver inputs to ground or
any other voltages. The input is biased by internal high
value pull up and pull down resistors to set the output to
a HIGH state. This internal circuitry will guarantee a
HIGH, stable output state for open inputs.
6
ential input voltage, the receiver output will remain in a
HIGH state. Shorted input fail-safe is not supported
across the common-mode range of the device (GND to
2.4V). It is only supported with inputs shorted and no
external common-mode voltage applied.
(Continued)
2. Terminated Input. If the driver is disconnected (cable
unplugged), or if the driver is in a TRI-STATE or poweroff condition, the receiver output will again be in a HIGH
state, even with the end of cable 100Ω termination resistor across the input pins. The unplugged cable can
become a floating antenna which can pick up noise. If
the cable picks up more than 10mV of differential noise,
the receiver may see the noise as a valid signal and
switch. To insure that any noise is seen as commonmode and not differential, a balanced interconnect
should be used. Twisted pair cable will offer better balance than flat ribbon cable.
3. Shorted Inputs. If a fault condition occurs that shorts
the receiver inputs together, thus resulting in a 0V differ-
External lower value pull up and pull down resistors (for a
stronger bias) may be used to boost fail-safe in the presence
of higher noise levels. The pull up and pull down resistors
should be in the 5kΩ to 15kΩ range to minimize loading and
waveform distortion to the driver. The common-mode bias
point should be set to approximately 1.2V (less than 1.75V)
to be compatible with the internal circuitry.
10131109
FIGURE 7. Driver Output Levels
Pin Descriptions
Pin No.
Name
1, 7, 9, 15
DIN
Description
Driver input pin, TTL/CMOS
compatible
2, 6, 10, 14
DOUT+ Non-inverting driver output pin,
LVDS levels
3, 5, 11, 13
DOUT− Inverting driver output pin, LVDS
levels
4
EN
Active high enable pin, OR-ed
with EN*
12
EN*
Active low enable pin, OR-ed with
EN
16
VCC
Power supply pin, +3.3V ± 0.3V
8
GND
Ground pin
Ordering Information
Operating
Package Type/
Temperature
Number
−40˚C to +85˚C
SOP/M16A
7
Order Number
DS90LV031BTM
www.national.com
DS90LV031B
Applications Information
DS90LV031B
Typical Performance Characteristics
10131110
FIGURE 8. Typical DS90LV031B, DOUT (single ended) vs RL, TA = 25˚C
10131111
FIGURE 9. Typical DS90LV031B, DOUT vs RL,
VCC = 3.3V, TA = 25˚C
www.national.com
8
DS90LV031B 3V LVDS Quad CMOS Differential Line Driver
Physical Dimensions
inches (millimeters)
unless otherwise noted
16-Lead (0.150" Wide) Molded Small Outline Package, JEDEC
Order Number DS90LV031BTM
NS Package Number M16A
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products
Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain
no ‘‘Banned Substances’’ as defined in CSP-9-111S2.
Leadfree products are RoHS compliant.
National Semiconductor
Americas Customer
Support Center
Email: [email protected]
Tel: 1-800-272-9959
www.national.com
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Support Center
Email: [email protected]
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: [email protected]
Tel: 81-3-5639-7560