KERSEMI IRFU3711ZC

PD - 96050
IRFR3711ZCPbF
IRFU3711ZCPbF
Applications
l High Frequency Synchronous Buck
Converters for Computer Processor Power
l High Frequency Isolated DC-DC
Converters with Synchronous Rectification
for Telecom and Industrial Use
l Lead-Free
HEXFET® Power MOSFET
VDSS
20V
Benefits
Very Low RDS(on) at 4.5V VGS
l Ultra-Low Gate Impedance
l Fully Characterized Avalanche Voltage
and Current
RDS(on) max
5.7m:
Qg
18nC
l
D-Pak
IRFR3711ZCPbF
I-Pak
IRFU3711ZCPbF
Absolute Maximum Ratings
Parameter
Max.
Units
20
V
VDS
Drain-to-Source Voltage
VGS
Gate-to-Source Voltage
Continuous Drain Current, VGS @ 10V
± 20
93
66
IDM
Continuous Drain Current, VGS @ 10V
Pulsed Drain Current
PD @TC = 25°C
Maximum Power Dissipation
PD @TC = 100°C
Maximum Power Dissipation
TJ
Linear Derating Factor
Operating Junction and
TSTG
Storage Temperature Range
ID @ TC = 25°C
ID @ TC = 100°C
c
f
f
A
370
g
g
79
W
39
0.53
-55 to + 175
Soldering Temperature, for 10 seconds
W/°C
°C
300 (1.6mm from case)
Thermal Resistance
Parameter
RθJC
RθJA
Junction-to-Case
Junction-to-Ambient (PCB Mount)
RθJA
Junction-to-Ambient
www.kersemi.com
g
Typ.
Max.
–––
1.9
–––
50
–––
110
Units
°C/W
1
02/23/06
IRFR/U3711ZCPbF
Static @ TJ = 25°C (unless otherwise specified)
Parameter
Min. Typ. Max. Units
BVDSS
Drain-to-Source Breakdown Voltage
∆ΒVDSS/∆TJ
Breakdown Voltage Temp. Coefficient
RDS(on)
Static Drain-to-Source On-Resistance
–––
20
V
Conditions
–––
–––
–––
13
–––
–––
4.5
5.7
mV/°C Reference to 25°C, ID = 1mA
mΩ VGS = 10V, ID = 15A
6.2
7.8
VGS = 4.5V, ID = 12A
VGS(th)
Gate Threshold Voltage
1.55
2.0
2.45
V
∆VGS(th)/∆TJ
Gate Threshold Voltage Coefficient
–––
-5.4
–––
mV/°C
IDSS
Drain-to-Source Leakage Current
µA
VGS = 0V, ID = 250µA
VDS = VGS, ID = 250µA
–––
–––
1.0
–––
–––
150
Gate-to-Source Forward Leakage
–––
–––
100
Gate-to-Source Reverse Leakage
–––
–––
-100
48
–––
–––
Total Gate Charge
–––
18
27
Qgs1
Pre-Vth Gate-to-Source Charge
–––
5.1
–––
Qgs2
Post-Vth Gate-to-Source Charge
–––
1.8
–––
Qgd
Gate-to-Drain Charge
–––
6.5
–––
ID = 12A
Qgodr
Gate Charge Overdrive
Switch Charge (Qgs2 + Qgd)
–––
4.6
–––
See Fig. 16
Qsw
–––
8.3
–––
IGSS
gfs
Qg
Forward Transconductance
e
e
VDS = 16V, VGS = 0V
VDS = 16V, VGS = 0V, TJ = 125°C
nA
VGS = 20V
VGS = -20V
S
VDS = 10V, ID = 12A
VDS = 10V
nC
VGS = 4.5V
Qoss
Output Charge
–––
9.8
–––
td(on)
Turn-On Delay Time
–––
12
–––
VDD = 15V, VGS = 4.5V
tr
Rise Time
–––
13
–––
ID = 12A
td(off)
Turn-Off Delay Time
–––
15
–––
tf
Fall Time
–––
5.2
–––
Ciss
Input Capacitance
–––
2160
–––
Coss
Output Capacitance
–––
700
–––
Crss
Reverse Transfer Capacitance
–––
360
–––
nC
ns
VDS = 10V, VGS = 0V
e
Clamped Inductive Load
VGS = 0V
pF
VDS = 10V
ƒ = 1.0MHz
Avalanche Characteristics
EAS
Parameter
Single Pulse Avalanche Energy
IAR
Avalanche Current
EAR
Repetitive Avalanche Energy
c
d
c
Typ.
Max.
Units
–––
140
mJ
–––
12
A
–––
7.9
mJ
Diode Characteristics
Parameter
Min. Typ. Max. Units
f
IS
Continuous Source Current
–––
–––
93
ISM
(Body Diode)
Pulsed Source Current
–––
–––
370
VSD
(Body Diode)
Diode Forward Voltage
–––
–––
1.0
V
trr
Reverse Recovery Time
–––
19
28
ns
Qrr
Reverse Recovery Charge
–––
9.4
14
nC
ton
Forward Turn-On Time
2
c
Conditions
MOSFET symbol
A
showing the
integral reverse
p-n junction diode.
TJ = 25°C, IS = 12A, VGS = 0V
e
TJ = 25°C, IF = 12A, VDD = 10V
di/dt = 100A/µs
e
Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD)
www.kersemi.com
IRFR/U3711ZCPbF
1000
1000
VGS
10V
4.5V
3.7V
3.5V
3.3V
3.0V
2.7V
BOTTOM 2.5V
VGS
10V
4.5V
3.7V
3.5V
3.3V
3.0V
2.7V
BOTTOM 2.5V
100
TOP
ID, Drain-to-Source Current (A)
ID, Drain-to-Source Current (A)
TOP
10
1
2.5V
100
10
2.5V
20µs PULSE WIDTH
Tj = 175°C
20µs PULSE WIDTH
Tj = 25°C
1
0.1
0.1
1
0.1
10
Fig 1. Typical Output Characteristics
10
Fig 2. Typical Output Characteristics
2.0
T J = 25°C
T J = 175°C
100
10
VDS = 10V
20µs PULSE WIDTH
1
ID = 30A
VGS = 10V
1.5
(Normalized)
RDS(on) , Drain-to-Source On Resistance
1000
ID, Drain-to-Source Current (Α)
1
VDS, Drain-to-Source Voltage (V)
VDS, Drain-to-Source Voltage (V)
1.0
0.5
2.0
3.0
4.0
5.0
6.0
7.0
VGS , Gate-to-Source Voltage (V)
Fig 3. Typical Transfer Characteristics
www.kersemi.com
8.0
-60 -40 -20
0
20 40 60 80 100 120 140 160 180
T J , Junction Temperature (°C)
Fig 4. Normalized On-Resistance
vs. Temperature
3
IRFR/U3711ZCPbF
VGS = 0V,
f = 1 MHZ
Ciss = C gs + Cgd, C ds
Crss = C gd
12
ID= 12A
SHORTED
VGS , Gate-to-Source Voltage (V)
10000
C, Capacitance (pF)
Coss = Cds + Cgd
Ciss
1000
Coss
Crss
100
10
8
6
4
2
0
1
10
100
0
10
VDS, Drain-to-Source Voltage (V)
1000
ID, Drain-to-Source Current (A)
ISD, Reverse Drain Current (A)
30
40
Fig 6. Typical Gate Charge vs.
Gate-to-Source Voltage
1000.0
100.0
T J = 175°C
10.0
T J = 25°C
1.0
20
Q G Total Gate Charge (nC)
Fig 5. Typical Capacitance vs.
Drain-to-Source Voltage
OPERATION IN THIS AREA
LIMITED BY R DS(on)
100
100µsec
10
1msec
Tc = 25°C
Tj = 175°C
Single Pulse
VGS = 0V
10msec
1
0.1
0.0
0.5
1.0
1.5
2.0
VSD, Source-toDrain Voltage (V)
Fig 7. Typical Source-Drain Diode
Forward Voltage
4
VDS= 18V
VDS= 10V
2.5
0.1
1.0
10.0
100.0
1000.0
VDS , Drain-toSource Voltage (V)
Fig 8. Maximum Safe Operating Area
www.kersemi.com
IRFR/U3711ZCPbF
100
2.5
VGS(th) Gate threshold Voltage (V)
LIMITED BY PACKAGE
ID , Drain Current (A)
80
60
40
20
0
2.0
1.5
ID = 250µA
1.0
0.5
0.0
25
50
75
100
125
150
175
-75 -50 -25
T C , Case Temperature (°C)
0
25
50
75
100 125 150 175
T J , Temperature ( °C )
Fig 9. Maximum Drain Current vs.
Case Temperature
Fig 10. Threshold Voltage vs. Temperature
Thermal Response ( Z thJC )
10
1
D = 0.50
0.20
0.10
0.05
0.1
τJ
0.02
0.01
R1
R1
τJ
τ1
R2
R2
τ2
τ1
τ2
Ci= τi/Ri
Ci= i/Ri
0.01
SINGLE PULSE
( THERMAL RESPONSE )
R3
R3
τ3
τC
τ
τ3
Ri (°C/W) τi (sec)
0.805
0.000237
0.606
0.001005
0.492
0.101628
Notes:
1. Duty Factor D = t1/t2
2. Peak Tj = P dm x Zthjc + Tc
0.001
1E-006
1E-005
0.0001
0.001
0.01
0.1
t1 , Rectangular Pulse Duration (sec)
Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case
www.kersemi.com
5
IRFR/U3711ZCPbF
15V
D.U.T
RG
+
V
- DD
IAS
20V
VGS
A
0.01Ω
tp
Fig 12a. Unclamped Inductive Test Circuit
V(BR)DSS
tp
EAS, Single Pulse Avalanche Energy (mJ)
DRIVER
L
VDS
600
ID
7.7A
8.9A
BOTTOM 12A
TOP
500
400
300
200
100
0
25
50
75
100
125
150
175
Starting T J , Junction Temperature (°C)
Fig 12c. Maximum Avalanche Energy
Vs. Drain Current
LD
I AS
VDS
Fig 12b. Unclamped Inductive Waveforms
+
VDD D.U.T
Current Regulator
Same Type as D.U.T.
VGS
Pulse Width < 1µs
Duty Factor < 0.1%
50KΩ
12V
.2µF
Fig 14a. Switching Time Test Circuit
.3µF
D.U.T.
+
V
- DS
VDS
90%
VGS
3mA
10%
IG
ID
VGS
Current Sampling Resistors
td(on)
Fig 13. Gate Charge Test Circuit
6
tr
td(off)
tf
Fig 14b. Switching Time Waveforms
www.kersemi.com
IRFR/U3711ZCPbF
D.U.T
Driver Gate Drive
P.W.
+
ƒ
+
‚
-
-
„
*
D.U.T. ISD Waveform
Reverse
Recovery
Current
+

RG
•
•
•
•
dv/dt controlled by RG
Driver same type as D.U.T.
I SD controlled by Duty Factor "D"
D.U.T. - Device Under Test
P.W.
Period
VGS=10V
Circuit Layout Considerations
• Low Stray Inductance
• Ground Plane
• Low Leakage Inductance
Current Transformer
-
D=
Period
V DD
+
-
Body Diode Forward
Current
di/dt
D.U.T. VDS Waveform
Diode Recovery
dv/dt
Re-Applied
Voltage
Body Diode
VDD
Forward Drop
Inductor Curent
ISD
Ripple ≤ 5%
* VGS = 5V for Logic Level Devices
Fig 15. Peak Diode Recovery dv/dt Test Circuit for N-Channel
HEXFET® Power MOSFETs
Id
Vds
Vgs
Vgs(th)
Qgs1 Qgs2
Qgd
Qgodr
Fig 16. Gate Charge Waveform
www.kersemi.com
7
IRFR/U3711ZCPbF
Power MOSFET Selection for Non-Isolated DC/DC Converters
Control FET
Synchronous FET
Special attention has been given to the power losses
in the switching elements of the circuit - Q1 and Q2.
Power losses in the high side switch Q1, also called
the Control FET, are impacted by the Rds(on) of the
MOSFET, but these conduction losses are only about
one half of the total losses.
The power loss equation for Q2 is approximated
by;
*
Ploss = Pconduction + Pdrive + Poutput
(
2
Ploss = Irms × Rds(on)
)
Power losses in the control switch Q1 are given
by;
+ (Qg × Vg × f )
Ploss = Pconduction+ Pswitching+ Pdrive+ Poutput
⎛Q
⎞
+ ⎜ oss × Vin × f + (Qrr × Vin × f )
⎝ 2
⎠
This can be expanded and approximated by;
*dissipated primarily in Q1.
Ploss = (Irms 2 × Rds(on ) )
⎛
Qgd
+⎜I ×
× Vin ×
ig
⎝
⎞
⎞ ⎛
Qgs 2
f⎟ + ⎜ I ×
× Vin × f ⎟
ig
⎠ ⎝
⎠
+ (Qg × Vg × f )
+
⎛ Qoss
× Vin × f ⎞
⎝ 2
⎠
This simplified loss equation includes the terms Qgs2
and Qoss which are new to Power MOSFET data sheets.
Qgs2 is a sub element of traditional gate-source
charge that is included in all MOSFET data sheets.
The importance of splitting this gate-source charge
into two sub elements, Qgs1 and Qgs2, can be seen from
Fig 16.
Qgs2 indicates the charge that must be supplied by
the gate driver between the time that the threshold
voltage has been reached and the time the drain current rises to Idmax at which time the drain voltage begins to change. Minimizing Q gs2 is a critical factor in
reducing switching losses in Q1.
Qoss is the charge that must be supplied to the output capacitance of the MOSFET during every switching cycle. Figure A shows how Qoss is formed by the
parallel combination of the voltage dependant (nonlinear) capacitance’s Cds and Cdg when multiplied by
the power supply input buss voltage.
For the synchronous MOSFET Q2, Rds(on) is an important characteristic; however, once again the importance of gate charge must not be overlooked since
it impacts three critical areas. Under light load the
MOSFET must still be turned on and off by the control IC so the gate drive losses become much more
significant. Secondly, the output charge Qoss and reverse recovery charge Qrr both generate losses that
are transfered to Q1 and increase the dissipation in
that device. Thirdly, gate charge will impact the
MOSFETs’ susceptibility to Cdv/dt turn on.
The drain of Q2 is connected to the switching node
of the converter and therefore sees transitions between ground and Vin. As Q1 turns on and off there is
a rate of change of drain voltage dV/dt which is capacitively coupled to the gate of Q2 and can induce
a voltage spike on the gate that is sufficient to turn
the MOSFET on, resulting in shoot-through current .
The ratio of Qgd/Qgs1 must be minimized to reduce the
potential for Cdv/dt turn on.
Figure A: Qoss Characteristic
8
www.kersemi.com
IRFR/U3711ZCPbF
D-Pak (TO-252AA) Package Outline
Dimensions are shown in millimeters (inches)
D-Pak (TO-252AA) Part Marking Information
(;$03/(
7+,6,6$1,5)5
3$57180%(5
:,7+$66(0%/<
,17(51$7,21$/
/27&2'(
,5)5
$
5(&7,),(5
$66(0%/('21::
/2*2
,17+($66(0%/</,1($
'$7(&2'(
<($5
:((.
/,1($
1RWH3LQDVVHPEO\OLQHSRVLWLRQ
$66(0%/<
LQGLFDWHV/HDG)UHH
/27&2'(
3LQDVVHPEO\OLQHSRVLWLRQLQGLFDWHV
/HDG)UHHTXDOLILFDWLRQWRWKH&RQVXPHUOHYHO
25
3$57180%(5
,17(51$7,21$/
5(&7,),(5
,5)5
/2*2
'$7(&2'(
3
'(6,*1$7(6/($')5((
3
'(6,*1$7(6/($')5((
352'8&7237,21$/
352'8&748$/,),('72
$66(0%/<
/27&2'(
&21680(5/(9(/237,21$/
<($5
:((.
$
www.kersemi.com
$66(0%/<6,7(&2'(
9
IRFR/U3711ZCPbF
I-Pak (TO-251AA) Package Outline
Dimensions are shown in millimeters (inches)
I-Pak (TO-251AA) Part Marking Information
(;$03/( 7+,6,6$1,5)8
:,7+$66(0%/<
/27&2'(
$66(0%/('21::
,17+($66(0%/</,1($
1RWH3LQDVVHPEO\OLQHSRVLWLRQ
LQGLFDWHV/HDG)UHH
,17(51$7,21$/
5(&7,),(5
/2*2
3$57180%(5
,5)8
$
$66(0%/<
/27&2'(
'$7(&2'(
<($5 :((.
/,1($
25
,17(51$7,21$/
5(&7,),(5
/2*2
3$57180%(5
,5)8
$66(0%/<
/27&2'(
10
'$7(&2'(
3 '(6,*1$7(6/($')5((
352'8&7237,21$/
<($5 :((.
$ $66(0%/<6,7(&2'(
www.kersemi.com
IRFR/U3711ZCPbF
D-Pak (TO-252AA) Tape & Reel Information
Dimensions are shown in millimeters (inches)
TR
TRR
16.3 ( .641 )
15.7 ( .619 )
12.1 ( .476 )
11.9 ( .469 )
FEED DIRECTION
TRL
16.3 ( .641 )
15.7 ( .619 )
8.1 ( .318 )
7.9 ( .312 )
FEED DIRECTION
NOTES :
1. CONTROLLING DIMENSION : MILLIMETER.
2. ALL DIMENSIONS ARE SHOWN IN MILLIMETERS ( INCHES ).
3. OUTLINE CONFORMS TO EIA-481 & EIA-541.
13 INCH
16 mm
NOTES :
1. OUTLINE CONFORMS TO EIA-481.
Notes:
 Repetitive rating; pulse width limited by
„ Calculated continuous current based on maximum allowable
max. junction temperature.
‚ Starting TJ = 25°C, L = 1.9mH, RG = 25Ω,
IAS = 12A.
ƒ Pulse width ≤ 400µs; duty cycle ≤ 2%.
… When mounted on 1" square PCB (FR-4 or G-10 Material).
www.kersemi.com
junction temperature. Package limitation current is 30A.
For recommended footprint and soldering techniques refer to
application note #AN-994.
11