IRF IRF3709ZCL

PD - 95836
IRF3709ZCS
IRF3709ZCL
Applications
l High Frequency Synchronous Buck
Converters for Computer Processor Power
HEXFET® Power MOSFET
VDSS RDS(on) max
6.3m:
30V
Benefits
l Low RDS(on) at 4.5V VGS
l Low Gate Charge
l Fully Characterized Avalanche Voltage
and Current
D2Pak
IRF3709ZCS
Qg
17nC
TO-262
IRF3709ZCL
Absolute Maximum Ratings
Parameter
Max.
Units
30
V
VDS
Drain-to-Source Voltage
VGS
Gate-to-Source Voltage
± 20
ID @ TC = 25°C
Continuous Drain Current, VGS @ 10V
87
ID @ TC = 100°C
Continuous Drain Current, VGS @ 10V
62
IDM
Pulsed Drain Current
350
PD @TC = 25°C
Maximum Power Dissipation
79
PD @TC = 100°C
Maximum Power Dissipation
40
TJ
Linear Derating Factor
Operating Junction and
TSTG
Storage Temperature Range
h
h
c
A
W
0.53
-55 to + 175
Soldering Temperature, for 10 seconds
W/°C
°C
300 (1.6mm from case)
Thermal Resistance
Parameter
RθJC
RθJA
Junction-to-Case
i
Junction-to-Ambient (PCB Mount)
g
Typ.
Max.
Units
–––
1.89
°C/W
–––
40
Notes  through ‡ are on page 11
www.irf.com
1
1/16/04
IRF3709ZCS/L
Static @ TJ = 25°C (unless otherwise specified)
Parameter
Min. Typ. Max. Units
BVDSS
Drain-to-Source Breakdown Voltage
30
–––
–––
∆ΒVDSS/∆TJ
Breakdown Voltage Temp. Coefficient
–––
0.021
–––
RDS(on)
Static Drain-to-Source On-Resistance
V
Conditions
VGS = 0V, ID = 250µA
–––
5.0
6.3
mV/°C Reference to 25°C, ID = 1mA
mΩ VGS = 10V, ID = 21A
–––
6.2
7.8
VGS = 4.5V, ID = 17A
e
e
VGS(th)
Gate Threshold Voltage
1.35
–––
2.25
V
∆VGS(th)/∆TJ
Gate Threshold Voltage Coefficient
–––
-5.5
–––
mV/°C
IDSS
Drain-to-Source Leakage Current
–––
–––
1.0
µA
VDS = 24V, VGS = 0V
–––
–––
150
IGSS
Gate-to-Source Forward Leakage
–––
–––
100
nA
VGS = 20V
Gate-to-Source Reverse Leakage
–––
–––
-100
Forward Transconductance
88
–––
–––
Total Gate Charge
–––
17
26
Qgs1
Pre-Vth Gate-to-Source Charge
–––
4.4
–––
Qgs2
Post-Vth Gate-to-Source Charge
–––
1.7
–––
Qgd
Gate-to-Drain Charge
–––
6.0
–––
ID = 17A
Qgodr
–––
4.9
–––
See Fig. 14a&b
Qsw
Gate Charge Overdrive
Switch Charge (Qgs2 + Qgd)
–––
7.7
–––
Qoss
Output Charge
–––
11
–––
td(on)
Turn-On Delay Time
–––
13
–––
VDD = 15V, VGS = 4.5V
tr
Rise Time
–––
41
–––
ID = 17A
td(off)
Turn-Off Delay Time
–––
16
–––
tf
Fall Time
–––
4.7
–––
Ciss
Input Capacitance
–––
2130
–––
Coss
Output Capacitance
–––
450
–––
Crss
Reverse Transfer Capacitance
–––
220
–––
gfs
Qg
VDS = VGS, ID = 250µA
VDS = 24V, VGS = 0V, TJ = 125°C
VGS = -20V
S
VDS = 15V, ID = 17A
nC
VGS = 4.5V
VDS = 15V
nC
VDS = 16V, VGS = 0V
e
ns
Clamped Inductive Load
pF
VDS = 15V
VGS = 0V
ƒ = 1.0MHz
Avalanche Characteristics
EAS
Parameter
Single Pulse Avalanche Energy
IAR
Avalanche Current
EAR
Repetitive Avalanche Energy
c
Typ.
–––
d
c
Units
mJ
Max.
60
–––
17
A
–––
7.9
mJ
Diode Characteristics
Parameter
Min. Typ. Max. Units
h
Conditions
IS
Continuous Source Current
–––
–––
87
ISM
(Body Diode)
Pulsed Source Current
–––
–––
350
showing the
integral reverse
VSD
(Body Diode)
Diode Forward Voltage
–––
–––
1.0
V
p-n junction diode.
TJ = 25°C, IS = 17A, VGS = 0V
trr
Reverse Recovery Time
–––
16
24
ns
Qrr
Reverse Recovery Charge
–––
6.2
9.3
nC
2
c
MOSFET symbol
A
D
G
S
e
TJ = 25°C, IF = 17A, VDD = 15V
di/dt = 100A/µs
e
www.irf.com
IRF3709ZCS/L
1000
1000
BOTTOM
TOP
ID, Drain-to-Source Current (A)
ID, Drain-to-Source Current (A)
TOP
VGS
10V
9.0V
7.0V
5.0V
4.5V
4.0V
3.5V
3.0V
100
100
3.0V
BOTTOM
VGS
10V
9.0V
7.0V
5.0V
4.5V
4.0V
3.5V
3.0V
3.0V
10
≤60µs PULSE WIDTH
≤60µs PULSE WIDTH
Tj = 175°C
Tj = 25°C
10
1
0.1
1
10
100
0.1
V DS, Drain-to-Source Voltage (V)
Fig 1. Typical Output Characteristics
10
100
Fig 2. Typical Output Characteristics
1000
2.0
RDS(on) , Drain-to-Source On Resistance
(Normalized)
ID, Drain-to-Source Current (Α)
1
V DS, Drain-to-Source Voltage (V)
T J = 175°C
100
10
1
T J = 25°C
VDS = 15V
≤60µs PULSE WIDTH
0.1
ID = 42A
VGS = 10V
1.5
1.0
0.5
0
1
2
3
4
5
6
7
VGS, Gate-to-Source Voltage (V)
Fig 3. Typical Transfer Characteristics
www.irf.com
8
-60 -40 -20 0
20 40 60 80 100 120 140 160 180
T J , Junction Temperature (°C)
Fig 4. Normalized On-Resistance
vs. Temperature
3
IRF3709ZCS/L
10000
6.0
VGS = 0V,
f = 1 MHZ
C iss = C gs + Cgd, C ds SHORTED
C rss = C gd
VGS, Gate-to-Source Voltage (V)
ID= 17A
C, Capacitance(pF)
C oss = C ds + Cgd
Ciss
1000
Coss
Crss
5.0
VDS= 24V
VDS= 15V
4.0
3.0
2.0
1.0
0.0
100
1
10
100
0
10
1000.00
20
25
ID, Drain-to-Source Current (A)
10000
OPERATION IN THIS AREA
LIMITED BY R DS(on)
1000
100.00
T J = 175°C
10.00
100
T J = 25°C
100µsec
10
1msec
1
Tc = 25°C
Tj = 175°C
Single Pulse
VGS = 0V
1.00
10msec
0.1
0.0
0.5
1.0
1.5
2.0
VSD, Source-to-Drain Voltage (V)
Fig 7. Typical Source-Drain Diode
Forward Voltage
4
15
Fig 6. Typical Gate Charge vs.
Gate-to-Source Voltage
Fig 5. Typical Capacitance vs.
Drain-to-Source Voltage
ISD, Reverse Drain Current (A)
5
QG Total Gate Charge (nC)
VDS, Drain-to-Source Voltage (V)
2.5
0
1
10
100
1000
VDS, Drain-to-Source Voltage (V)
Fig 8. Maximum Safe Operating Area
www.irf.com
IRF3709ZCS/L
90
80
VGS(th) Gate threshold Voltage (V)
2.5
Limited By Package
ID, Drain Current (A)
70
60
50
40
30
20
10
2.0
1.5
ID = 250µA
1.0
0.5
0
25
50
75
100
125
150
-75 -50 -25
175
0
25
50
75 100 125 150 175 200
T J , Temperature ( °C )
T C , Case Temperature (°C)
Fig 9. Maximum Drain Current vs.
Case Temperature
Fig 10. Threshold Voltage vs. Temperature
Thermal Response ( Z thJC )
10
1
D = 0.50
0.20
0.10
0.05
0.1
τJ
0.02
0.01
0.01
R1
R1
τJ
τ1
τ1
R2
R2
τ2
τC
τ
τ2
Ri (°C/W) τi (sec)
0.832
0.000221
1.058
0.001171
Ci= τi/Ri
Ci i/Ri
SINGLE PULSE
( THERMAL RESPONSE )
Notes:
1. Duty Factor D = t1/t2
2. Peak Tj = P dm x Zthjc + Tc
0.001
1E-006
1E-005
0.0001
0.001
0.01
0.1
t1 , Rectangular Pulse Duration (sec)
Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case
www.irf.com
5
RDS(on), Drain-to -Source On Resistance (m Ω)
RDS(on), Drain-to -Source On Resistance ( mΩ)
IRF3709ZCS/L
9.00
Vgs = 10V
8.00
T J = 125°C
7.00
6.00
T J = 25°C
5.00
4.00
10.0
20.0
30.0
40.0
50.0
60.0
70.0
16
ID = 21A
14
12
10
T J = 125°C
8
6
T J = 25°C
4
2
0
2
ID, Drain Current (A)
3
4
5
6
7
8
9
10
VGS, Gate -to -Source Voltage (V)
Fig 12. On-Resistance vs. Drain Current
Fig 13. On-Resistance vs. Gate Voltage
Current Regulator
Same Type as D.U.T.
Id
Vds
50KΩ
Vgs
.2µF
12V
250
.3µF
EAS , Single Pulse Avalanche Energy (mJ)
D.U.T.
+
V
- DS
Vgs(th)
VGS
3mA
IG
ID
Current Sampling Resistors
Qgs1 Qgs2
Qgd
Qgodr
Fig 14a&b. Basic Gate Charge Test Circuit
and Waveform
15V
V(BR)DSS
tp
L
VDS
D.U.T
RG
IAS
20V
I AS
tp
DRIVER
+
V
- DD
0.01Ω
Fig 15a&b. Unclamped Inductive Test circuit
and Waveforms
6
ID
5.4A
8.0A
BOTTOM 17A
TOP
200
150
100
50
0
A
25
50
75
100
125
150
175
Starting T J , Junction Temperature (°C)
Fig 16. Maximum Avalanche Energy
vs. Drain Current
www.irf.com
IRF3709ZCS/L
D.U.T
Driver Gate Drive
+
ƒ
+
-
-
„
*
D.U.T. ISD Waveform
Reverse
Recovery
Current
+

RG
•
•
•
•
dv/dt controlled by RG
Driver same type as D.U.T.
ISD controlled by Duty Factor "D"
D.U.T. - Device Under Test
P.W.
Period
VGS=10V
Circuit Layout Considerations
• Low Stray Inductance
• Ground Plane
• Low Leakage Inductance
Current Transformer
‚
D=
Period
P.W.
VDD
+
Body Diode Forward
Current
di/dt
D.U.T. VDS Waveform
Diode Recovery
dv/dt
Re-Applied
Voltage
-
Body Diode
VDD
Forward Drop
Inductor Curent
Ripple ≤ 5%
ISD
* VGS = 5V for Logic Level Devices
Fig 17. Peak Diode Recovery dv/dt Test Circuit for N-Channel
HEXFET® Power MOSFETs
LD
VDS
+
VDD D.U.T
VGS
Pulse Width < 1µs
Duty Factor < 0.1%
Fig 18a. Switching Time Test Circuit
VDS
90%
10%
VGS
td(on)
tr
td(off)
tf
Fig 18b. Switching Time Waveforms
www.irf.com
7
IRF3709ZCS/L
Power MOSFET Selection for Non-Isolated DC/DC Converters
Control FET
Synchronous FET
Special attention has been given to the power losses
in the switching elements of the circuit - Q1 and Q2.
Power losses in the high side switch Q1, also called
the Control FET, are impacted by the Rds(on) of the
MOSFET, but these conduction losses are only about
one half of the total losses.
The power loss equation for Q2 is approximated
by;
*
Ploss = Pconduction + Pdrive + Poutput
(
2
Ploss = Irms × Rds(on)
)
Power losses in the control switch Q1 are given
by;
+ (Qg × Vg × f )
Ploss = Pconduction+ Pswitching+ Pdrive+ Poutput
⎛Q
⎞
+ ⎜ oss × Vin × f + (Qrr × Vin × f )
⎠
⎝ 2
This can be expanded and approximated by;
*dissipated primarily in Q1.
Ploss = (Irms × Rds(on ) )
2
⎛
⎞ ⎛
Qgs 2
Qgd
+⎜I×
× Vin × f ⎟ + ⎜ I ×
× Vin ×
ig
ig
⎝
⎠ ⎝
⎞
f⎟
⎠
+ (Qg × Vg × f )
+
⎛ Qoss
× Vin × f ⎞
⎝ 2
⎠
This simplified loss equation includes the terms Qgs2
and Qoss which are new to Power MOSFET data sheets.
Qgs2 is a sub element of traditional gate-source
charge that is included in all MOSFET data sheets.
The importance of splitting this gate-source charge
into two sub elements, Qgs1 and Qgs2, can be seen from
Fig 16.
Qgs2 indicates the charge that must be supplied by
the gate driver between the time that the threshold
voltage has been reached and the time the drain current rises to Idmax at which time the drain voltage begins to change. Minimizing Qgs2 is a critical factor in
reducing switching losses in Q1.
Qoss is the charge that must be supplied to the output capacitance of the MOSFET during every switching cycle. Figure A shows how Qoss is formed by the
parallel combination of the voltage dependant (nonlinear) capacitance’s Cds and Cdg when multiplied by
the power supply input buss voltage.
For the synchronous MOSFET Q2, Rds(on) is an important characteristic; however, once again the importance of gate charge must not be overlooked since
it impacts three critical areas. Under light load the
MOSFET must still be turned on and off by the control IC so the gate drive losses become much more
significant. Secondly, the output charge Qoss and reverse recovery charge Qrr both generate losses that
are transfered to Q1 and increase the dissipation in
that device. Thirdly, gate charge will impact the
MOSFETs’ susceptibility to Cdv/dt turn on.
The drain of Q2 is connected to the switching node
of the converter and therefore sees transitions between ground and Vin. As Q1 turns on and off there is
a rate of change of drain voltage dV/dt which is capacitively coupled to the gate of Q2 and can induce
a voltage spike on the gate that is sufficient to turn
the MOSFET on, resulting in shoot-through current .
The ratio of Qgd/Qgs1 must be minimized to reduce the
potential for Cdv/dt turn on.
Figure A: Qoss Characteristic
8
www.irf.com
IRF3709ZCS/L
D2Pak Package Outline
Dimensions are shown in millimeters (inches)
D2Pak Part Marking Information
7+,6,6$1,5)6:,7+
/27&2'(
$66(0%/('21::
,17+($66(0%/</,1(/
,17(51$7,21$/
5(&7,),(5
/2*2
$66(0%/<
/27&2'(
www.irf.com
3$57180%(5
)6
'$7(&2'(
<($5 :((.
/,1(/
9
IRF3709ZCS/L
TO-262 Package Outline
Dimensions are shown in millimeters (inches)
1- GATE
IGBT
2- COLLECTOR
TO-262 Part Marking Information
/
/
,5
1
$
,6
,6
7+
/(
3
0
$
(;
5
(
),
7,
&
(
5
:
:
1
2
'
/(
%
0
(
6
6
$
/
$
1
2
7,
$
1
5
7(
,1
5
(
%
0
8
1
7
5
$
3
(
'
2
&
7
/2
2
*
/2
&
(
,1
/
/<
%
(0
6
6
$
(
+
7
,1
(
'
2
&
7(
$
'
/<
%
0
(
6
6
$
5
$
<(
(
'
2
&
7
/2
.
(
(
:
&
(
1
/,
www.irf.com
10
IRF3709ZCS/L
D2Pak Tape & Reel Information
Dimensions are shown in millimeters (inches)
TRR
1.60 (.063)
1.50 (.059)
4.10 (.161)
3.90 (.153)
FEED DIRECTION 1.85 (.073)
1.65 (.065)
1.60 (.063)
1.50 (.059)
11.60 (.457)
11.40 (.449)
0.368 (.0145)
0.342 (.0135)
15.42 (.609)
15.22 (.601)
24.30 (.957)
23.90 (.941)
TRL
10.90 (.429)
10.70 (.421)
1.75 (.069)
1.25 (.049)
4.72 (.136)
4.52 (.178)
16.10 (.634)
15.90 (.626)
FEED DIRECTION
13.50 (.532)
12.80 (.504)
27.40 (1.079)
23.90 (.941)
4
330.00
(14.173)
MAX.
60.00 (2.362)
MIN.
NOTES :
1. COMFORMS TO EIA-418.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION MEASURED @ HUB.
4. INCLUDES FLANGE DISTORTION @ OUTER EDGE.
30.40 (1.197)
MAX.
26.40 (1.039)
24.40 (.961)
3
4
Notes:
 Repetitive rating; pulse width limited by
… This is applied to D2Pak, when mounted on 1" square PCB (FR4 or G-10 Material). For recommended footprint and soldering
max. junction temperature.
techniques refer to application note #AN-994.
‚ Starting TJ = 25°C, L = 0.42mH, RG = 25Ω,
† Calculated continuous current based on maximum allowable
IAS = 17A.
junction temperature. Package limitation current is 42A.
ƒ Pulse width ≤ 400µs; duty cycle ≤ 2%.
„ Coss eff. is a fixed capacitance that gives the same ‡ Rθ is measured at TJ of approximately 90°C.
charging time as Coss while VDS is rising from 0 to
80% VDSS.
Data and specifications subject to change without notice.
This product has been designed and qualified for the Consumer market.
Qualification Standards can be found on IR’s Web site.
IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105
TAC Fax: (310) 252-7903
Visit us at www.irf.com for sales contact information. 01/04
www.irf.com
11