MVJL/MVJP Series PECL/LCPECL VCXO Hermetically Sealed Ceramic SMD Package Wide Frequency Range Available to -55°C to +125°C Operating Less than 1 pSec Jitter Frequency Range 70.000 MHz to 622.080 MHz Frequency Stability (Inclusive of Temp., Load and Voltage) (See Part Number Guide for Options) Aging Operating Temp.Range Storage Temp. Range Supply Voltage (Vdd) Supply Current Control Voltage Logic “0” Logic “1” Symmetry (50% of waveform) Load Rise / Fall Time (20% to 80%) Start Time Jitter (RMS) Linearity Pullability ±5 ppm / yr max (See Part Number Guide for Options) -55°C to +125°C +3.3 VDC ±5% (LVPECL) +5.0 VDC ±5% (PECL) 60mA 85mA +1.65VDC ±1.50VDC +2.50VDC ±2.00VDC Vdd – 1.620 Vdc max Vdd- 1.025 Vdc min (See Part Number Guide for Options) 50 Ohms into Vdd-2.00 VDC 5nSec max 5mSec max Less than 1 pSec ±10% max (See Part Number Guide for Options) Voh = 70% of Vdd min or No Connection to Enable Output Vol = 30% max or grounded to Disable, Output (High Impedance) Tri-State Operation Environmental & Mechanical Detail Humidty Hermetic Seal 85% RH, 85°C, 48 Hours Leak Rate 2 X 10-8 ATM-cm3/sec max Solderability MIL-STD-202G, Method 208 Reflow Solderability Vibration Shock MIL-STD-883 260°C for 10 seconds MIL-STD-202G, Method 204 35G, 50 to 2000 Hz MIL-STD-202G, Method 203 Test Cond E, 1000G’s, ½ Sinewave Available with Level B Screening Marking Detail Line 1 = MXXXXX M = MMD XXXXX = Frequency in MHZ S = Internal Code YYWW = 4 Digit Date Code (Year / Week) L = Denotes RoHS Compliant Line 2 = SYYWWL Line 3 = XXXXX Internal use only May vary with lots Pin 1 Indicator MMD Monitor/Quartztek 30400 Esperanza, Rancho Santa Margarita, CA, 92688 Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com [email protected] Revision: Revisions only with customer approval 08/31/11 E Pg 1 of 2 Part Number Guide M VJ 1 Value Added Options Blank = Bulk T = Tape & Reel Frequency Ceram ic SM D 6 J-Leads Supply Voltage P = PECL (+5.0VDC) L = LVPECL (+3.3VDC) Frequency Stability Pullability** Operating Tem perature Sym m etry * 020 = ±20 ppm A = ±200 ppm Blank = 0°C to +70°C 025 = ±25 ppm C = ±100 ppm Blank = 40/60% 27 = -20°C to +70°C D = ±50 ppm 050 = ±50 ppm A = 45/55% 48 = -40°C to +85°C 100 = ±100 ppm P = ±25 ppm B = 47.5/52.5% 55 = -55°C to +125°C *Option B (47.5/52.5% ) Available up to 500MHz only **200ppm Pullability not available with 3.3V Supply Please Consult with MMD sales department for any other parameters or options. Jitter 1 = Less than 1 pSec Jitter Mechanical Details 9.80 [.386] M AX 4.70 [.185] M AX MXXXXX SYYWWL XXXXX 0.84 [.033] 14.00 [.551] M AX 5.08 [.200] 2.54 [.100] DENOTES PIN 1 PIN 1 INDICATO R Dim ension in Brackets are in Inches External Bypass Capacitor is Recom m ended 7.87 [.310] 3 4 2 5 1 6 5.08 [.200] 1.02 [.040] 2.54 [.100] 2.50 [.098] PIN PIN PIN PIN PIN PIN PIN CO NNECTIONS 1 VOLTAGE CONTROL 2 ENABLE/DISABLE 3 GROUND 4 OUTPUT 5 COMP. O UTPUT 6 SUPPLY VO LTAGE Suggested Land Pattern Tape & Reel Dimensions PITCH Tape Width Q1 Q2 Q1 Q2 Q3 Q4 Q3 Q4 REEL DIA PITCH TAPE WIDTH REEL DIA PIN 1 ORIENT. COUNT 12.00 [.471] 24.00 [.945] 330 [13.0] Q1 500 NOTES: UNLESS OTHERWISE SPECIFIED 1. Applicable Standards / Specifications ANSI Y14.5M, Dimensions and Tolerances EIA-481-B, 8 mm through 200mm Embossed Carrier Taping and 8 mm and 12 mm Punched Carrier Taping of Surface Mount Components for Automatic Handling. 2. Dimensions are in millimeters [inch]. 3. Tolerances are ±0.1 [.004] mm unless otherwise specified. 4. Do not scale drawing. DIRECTION OF FEED MMD Monitor/Quartztek 30400 Esperanza, Rancho Santa Margarita, CA, 92688 Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com [email protected] Revision: Revisions only with customer approval 08/31/11 E Pg 2 of 2