7/16 DIN Male Right Angle Connector Clamp/Solder Attachment For 1/2 inch Annular, 1/2 inch Flexible, PE-1/2FAC TECHNICAL DATA SHEET PE44569 7/16 DIN Male Right Angle Connector Clamp/Solder Attachment For 1/2 inch Annular, 1/2 inch Flexible, PE-1/2FAC Configuration Connector Connector Interface Type Cable Attachment Method (Shield/Contact) Body Style 7/16 DIN Male 1/2 inch Annular,1/2 inch Flexible,PE-1/2FAC Clamp/Solder Right Angle Electrical Specifications Frequency Range, GHz Impedance, Ohms Maximum Return Loss, dB Maximum Operating Voltage, Volts DC to 3 50 28 2,700 Frequency 1 Frequency, GHz Insertion Loss, dB Power Handling, Watts DC to 2 0.05 400 Mechanical Specifications Temperature Operating Range, deg C -40 to +85 Size Length, in [mm] Width/Dia., in [mm] Height, in [mm] 2.853 [72.47] 1.26 [32.00] 1.808 [45.92] Weight, lbs [g] 0.54 [244.94] Connector Type Contact Material and Plating Contact Plating Specification Coupling Nut Material and Plating Coupling Nut Plating Specification Hex Size, mm Torque, ft-lbs [Nm] Body Material and Plating Body Plating Specification Dielectric Type 7/16 DIN Male Beryllium Copper, Silver 5µ in. minimum Brass, Tri-Metal 2µ in. minimum 32 18.417 [24.97] Brass, Tri-Metal 2µ in. minimum Teflon . Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price, inventory and certifications: 7/16 DIN Male Right Angle Connector Clamp/Solder Attachment For 1/2 inch Annular, 1/2 inch Flexible, PE-1/2FAC PE44569 PE44569 REV 01 1 7/16 DIN Male Right Angle Connector Clamp/Solder Attachment For 1/2 inch Annular, 1/2 inch Flexible, PE-1/2FAC TECHNICAL DATA SHEET PE44569 Compliance Certifications (visit www.Pasternack.com for current document) RoHS Compliant Yes Plotted and Other Data Notes: Values at 25 °C, sea level 7/16 DIN Male Right Angle Connector Clamp/Solder Attachment For 1/2 inch Annular, 1/2 inch Flexible, PE-1/2FAC from Pasternack Enterprises has same day shipment for domestic and International orders. Our RF, microwave and fiber optic products maintain a 99% availability and are part of the broadest selection in the industry. Click the following link (or enter part number in “SEARCH” on website) to obtain additional part information including price, inventory and certifications: 7/16 DIN Male Right Angle Connector Clamp/Solder Attachment For 1/2 inch Annular, 1/2 inch Flexible, PE-1/2FAC PE44569 URL: http://www.pasternack.com/7-16-male-standard-1-2-inch-annular-connector-pe44569-p.aspx PE44569 REV 01 2 ASSEMBLY PROCEDURES © 2013 Pasternack Enterprises All Rights Reserved PE44569 REV 01 SHOWN BELOW. 6. HEAT THE SHRINK TUBING UNTIL IT MOLDS OVER THE CABLE, AS 5. HOLD CLAMP NUT STEADY & SCREW BODY TIGHTLY ONTO CABLE. 4. SLIDE O-RING OVER THREAD AND SEAT INTO PLACE. GREASE O-RING. 3. FLARE THE OUTER CONDUCTOR, SEPARATING THE OUTER CONDUCTOR FROM THE INSULATOR. 2. GREASE O-RING INSIDE OF CLAMP NUT. INSTALL CLAMP NUT ONTO CABLE. 1. STRIP CABLE AS SHOWN, CHAMFER CENTER CONDUCTOR & DEBURR CABLE. SLIDE HEAT SHRINK OVER CABLE. FSCM NO. 53919 PE44569 DWG TITLE CAD FILE 100708-A SCALE N/A SIZE A XXXX NOTES: 1. UNLESS OTHERWISE SPECIFIED ALL DIMENSIONS ARE NOMINAL. 2. ALL SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE AT ANY TIME. 3. DIMENSIONS ARE IN INCHES [mm]. 4. FITS MIL-C-17 AND EQUIVALENT CABLES. 7/16 DIN Male Right Angle Connector Clamp/Solder Attachment For 1/2 inch Annular, 1/2 inch Flexible, PE-1/2FAC PE44569 CAD Drawing 3