LM2636 5-Bit Programmable Synchronous Buck Regulator Controller General Description The LM2636 is a high speed controller designed specifically for use in synchronous DC/DC buck converters for advance d microprocessors. A 5-bit DAC accepts the VID code directly from the CPU and adjusts the output voltage from 1.3V to 3.5V. It provides the power good, over-voltage protection, and output enable features as required by Intel VRM specifications. Current limiting is achieved by monitoring the voltage drop across the rDS_ON of the high side MOSFET, which eliminates an expensive current sense resistor. The LM2636 employs a fixed-frequency voltage mode PWM architecture. To provide a faster response to a large and fast load transient, two ultra-fast comparators are built in to monitor the output voltage and override the primary control loop when necessary. The PWM frequency is adjustable from 50 kHz to 1 MHz through an external resistor. The wide range of PWM frequency gives the power supply designer the flexibility to make trade-offs between load transient response performance, MOSFET cost and the overall efficiency. The adaptive non-overlapping MOSFET gate drivers help avoid any potential shoot-through problem while maintaining high efficiency. BiCMOS gate drivers with rail-to-rail swing ensure that no spurious turn-on occur. When only 5V is available, a bootstrap structure can be employed to accommodate an NMOS high side switch. The precision reference trimmed to 2.5% over temperature is available externally for use by other regulators. Dynamic positioning of load voltage, which helps cut the number of output capacitors, can also be implemented easily. Features n n n n n n n n n n n 1.3V to 3.5V 5-bit programmable output voltage Synchronous rectification Power Good flag and output enable Over-voltage protection Initial Output Accuracy: 1.5% over temperature Current limit without external sense resistor Adaptive non-overlapping MOSFET gate drives Adjustable switching frequency: 50 kHz to 1 MHz Dynamic output voltage positioning 1.256V reference voltage available externally Plastic SO-20 package and TSSOP-20 package Applications n Motherboard power supply/VRM for Cyrix Gxm, Cyrix Gxi, Cyrix MII, Pentium™ II, Pentium Pro, 6x86 and K6 processors n 5V to 1.3V–3.5V high current power supplies Typical Application DS100834-1 FIGURE 1. 5V to 1.3V–3.5V, 14A Power Supply Pentium™ is a trademark of Intel Corporation. © 1999 National Semiconductor Corporation DS100834 www.national.com LM2636 5-Bit Programmable Synchronous Buck Regulator Controller October 1999 LM2636 Connection Diagrams is on, it means VDS is higher than the preset voltage across the IMAX resistor, which can be interpreted as an overcurrent condition. TOP VIEW VREF (Pin 9): Bandgap reference voltage. This voltage is mainly for use by other power supplies on the motherboard which need a reference. EA_OUT (Pin 10): Output of the error amplifier. The voltage level on this pin is compared with an internally generated ramp signal to determine the duty cycle. This pin is necessary for compensating the primary control loop. FB (Pin 11): Inverting input of the error amplifier. A pin necessary for compensating the control loop. FREQ_ADJ (Pin 12): Switching frequency adjustment. Switching frequency can be adjusted by changing the grounding resistance on this pin. DS100834-3 Plastic SO-20 Order Number LM2636M See NS Package Number M20B PWRGD (Pin 13): Power Good. There are two windows around the DAC output voltage that are associated with PWRGD pin, the ± 10% window and the ± 8% window. If PWRGD is initially high (open drain state) and output voltage travels out of ± 10% window, PWRGD goes to low (low impedance to ground). If PWRGD is initially low and output voltage travels into the ± 8% window and has stayed within the window for at least 10 ms, PWRGD goes to high. A PWRGD high means the output voltage is at least within the ± 10% window whereas a PWRGD low indicates the output voltage is definitely outside the ± 8% window. VID4:0 (Pins 14, 15, 16, 17, 18): Voltage Identification Code. The five pins accept an open-ground pattern 5-bit binary code from outside the chip (typically from the CPU) for generating the desired output voltage. Each VID pin is internally pulled up to VCC via a 90 µA current source. Table 1 shows the code table. OUTEN (Pin 19): Output Enable. The output voltage is disabled when this pin is pulled low. It is internally pulled up to VCC via a 90 µA current source. HSGATE (Pin 20): Gate drive for the high-side N-channel MOSFET. This signal is interlocked with LSGATE (Pin 1) to avoid a shoot-through problem. TOP VIEW DS100834-3 Plastic TSSOP-20 Order Number LM2636MTC See NS Package Number MTC20 Pin Descriptions LSGATE (Pin 1): Gate drive for the low-side N-channel MOSFET. This signal is interlocked with HSGATE (Pin 20) to avoid a shoot-through problem. BOOTV (Pin 2): Power supply for high-side N-channel MOSFET gate drive. The voltage should be at least one gate threshold above the converter input voltage to properly operate the high-side N-FET. PGND (Pin 3): Ground for high current circuitry. It should be connected to system ground. TABLE 1. VID Code and DAC Output SGND (Pin 4): Ground for signal level circuitry. It should be connected to system ground. VCC (Pin 5): Power supply for the controller. SENSE (Pin 6): Converter output voltage sensing. It provides input for power good, fast dual comparator control loop, and over-voltage protection circuitry. It is recommended that a 0.1 µF capacitor be connected between this pin and ground to avoid potential noise problems. IMAX (Pin 7): Current limit threshold setting. It sinks a fixed 180 µA current. By connecting a resistor between the high side MOSFET drain and this pin, a fixed voltage drop can be built across the resistor. This voltage drop is compared with the VDS of the high-side N-MOSFET to determine if an overcurrent condition has occurred. IFB (Pin 8): High-side N-MOSFET source voltage sensing. This pin is one VDS below drain voltage. When this voltage is lower than that of IMAX pin during the time the high-side FET www.national.com 2 VID4 VID3 VID2 VID1 VID0 Rated Output Voltage (V) 0 1 1 1 1 1.30 0 1 1 1 0 1.35 0 1 1 0 1 1.40 0 1 1 0 0 1.45 0 1 0 1 1 1.50 0 1 0 1 0 1.55 0 1 0 0 1 1.60 0 1 0 0 0 1.65 0 0 1 1 1 1.70 0 0 1 1 0 1.75 0 0 1 0 1 1.80 0 0 1 0 0 1.85 0 0 0 1 1 1.90 0 0 0 1 0 1.95 0 0 0 0 1 2.00 LM2636 Pin Descriptions (Continued) TABLE 1. VID Code and DAC Output (Continued) Rated Output Voltage (V) VID4 VID3 VID2 VID1 VID0 0 0 0 0 0 2.05 1 1 1 1 1 (shutdown) 1 1 1 1 0 2.1 1 1 1 0 1 2.2 1 1 1 0 0 2.3 1 1 0 1 1 2.4 1 1 0 1 0 2.5 1 1 0 0 1 2.6 1 1 0 0 0 2.7 1 0 1 1 1 2.8 1 0 1 1 0 2.9 1 0 1 0 1 3.0 1 0 1 0 0 3.1 1 0 0 1 1 3.2 1 0 0 1 0 3.3 1 0 0 0 1 3.4 1 0 0 0 0 3.5 3 www.national.com LM2636 Absolute Maximum Ratings (Note 1) Soldering Time, Temperature Wave (4 seconds) Infrared (10 seconds) Vapor Phase (75 seconds) ESD Susceptibility (Note 3) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. (All voltages are referenced to the PGND and SGND pins.) 7V VCC BOOTV 18V Junction Temperature 150˚C DC Power Dissipation (Note 2) 1.42W Storage Temperature −65˚C to +150˚C 260˚C 240˚C 219˚C 2 kV Recommended Operating Conditions (Note 1) Supply Voltage Range (VCC) Junction Temperature Range 4.5V to 5.5V 0˚C to +125˚C Electrical Characteristics VCC = 5V unless otherwise indicated under the Conditions column. Typicals and limits appearing in plain type apply for TA = TJ = +25˚C. Limits appearing in boldface type apply over 0˚C to +70˚C. Symbol Parameter VBOOTV FET Driver Supply Voltage VDACOUT 5-Bit DAC Output Voltage ∆VOUT Conditions Min Typ Max Units 18 V VID4:0=01111 1.284 1.304 1.324 VID4:0=01101 1.385 1.406 1.427 VID4:0=01011 1.483 1.506 1.529 VID4:0=01001 1.585 1.609 1.633 VID4:0=00111 1.683 1.709 1.735 VID4:0=00101 1.784 1.811 1.838 VID4:0=00001 1.983 2.013 2.043 VID4:0=11101 2.173 2.206 2.239 VID4:0=11010 2.471 2.509 2.547 VID4:0=10111 2.768 2.81 2.852 DC Load Regulation IOUT=0 to 14A Figure 2 −5 DC Line Regulation VIN=4.75V to 5.25V Figure 2 1 V mV GEA Error Amplifier DC Gain 85 dB SREA Error Amplifier Slew Rate 6 V/µs BWEA Error Amplifier Unity Gain Bandwidth 5 MHz Operating VCC Current OUTEN=VCC=5V, VID=10111 Shutdown VCC Current OUTEN Floating, VID0:4 Floating IQ_BOOTV BOOTV Pin Quiescent Current BOOTV=12V, OUTEN=0, VID0:4 Floating IQ_VCC 1.5 2.5 4 1 1.5 3 mA 4 µA DMAX Maximum Duty Cycle 90 % DMIN Minimum Duty Cycle 0 % RSENSE SENSE Pin Resistance to Ground RDS_SRC FET Driver Drain-Source ON Resistance when Sourcing Current BOOTV=5V FET Driver Drain-Source ON Resistance when Sinking Current (Independent of BOOTV Voltage) Oscillator Frequency RFA = 84 kΩ RDS_SINK fOSC IMAX www.national.com IMAX Pin Sink Current 7 250 11.5 Ω 1.7 Ω 300 1000 RFA = 10.5 kΩ 2000 4 130 kΩ 7 RFA = 22 kΩ VIMAX = 5V, VIFB = 6V, VCC = 5V 16 180 350 kHz 230 µA (Continued) Symbol Parameter Conditions OUTEN Pin Input Logic Low to Logic High Trip Point OUTEN Voltage ↑ OUTEN Pin Input Logic High to Logic Low Trip Point OUTEN Voltage ↓ VREF Band Gap Reference IVREF = 0 mA VREF_LOAD Reference Voltage at Full Load IVREF = 0.5 mA, Sourcing VREF_525 Reference Voltage at High Line IVREF = 0 mA, VCC = 5.25V VREF_475 Reference Voltage at Low Line IVREF = 0 mA, VCC = 4.75V ∆VREF_LOAD Reference Voltage Load Regulation IVREF = 0.5 mA, Sourcing ∆VREF_LINE Reference Voltage Line Regulation IVREF = 0 mA, VCC Changes from 5.25V to 4.75V VSAWL VOUTEN_IH VOUTEN_IL Min Typ 3.5 3.0 Max Units V 1.8 1.5 V 1.225 1.256 1.287 V 1.223 1.254 1.285 V 1.226 1.257 1.288 V 1.224 1.255 1.286 V −2 mV −0.5 mV Ramp Signal Valley Voltage 1.25 V VSAWH Ramp Signal Peak Voltage 3.25 V VPWRBAD_GD PWRGD Pin ↓ Trip Points (see Pin Description for Pin 13) VPWRGD_BAD PWRGD Pin ↑ Trip Points (see Pin Description for Pin 13) % above DAC Output Voltage, when Output Voltage ↑ 10 % below DAC Output Voltage, when Output Voltage ↓ −10 % above DAC Output Voltage, when Output Voltage ↓ 8 % below DAC Output Voltage, when Output Voltage ↑ −8 VOVP Over-voltage Protection Trip Point % above DAC Output Voltage tPWRGD Power Good Response Time VSENSE Rises from 0V to Rated VOUT tPWRBAD Power Not Good Response Time VSENSE Falls from Rated VOUT to 0V IOUTEN % % % 15 2 6 15 µs 2 6 15 µs OUTEN Pin Internal Pull-Up Current 60 90 130 µA VVID_IH VID Pins Logic High Trip Point 3.5 3.0 VVID_IL VID Pins Logic Low Trip Point IVID VID0:4 Internal Pull-Up Current tSS Soft Start Duration 60 V 1.8 1.3 V 90 130 µA 2048 clock cycles Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Recommended Operating Conditions are conditions under which the device operates correctly. Recommended Operating Conditions do not imply guaranteed performance limits. Note 2: Maximum allowable DC power dissipation is a function of the maximum junction temperature, TJMAX , the junction-to-ambient thermal resistance, θJA, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperature is calculated using: The junction-to-ambient thermal resistance, θJA, for LM2636 in the M20B package is 88˚C/W, and 120˚C/W for the MTC20 package. 5 www.national.com LM2636 Electrical Characteristics VCC = 5V unless otherwise indicated under the Conditions column. Typicals and limits appearing in plain type apply for TA = TJ = +25˚C. Limits appearing in boldface type apply over 0˚C to +70˚C. LM2636 Electrical Characteristics (Continued) Note 3: All pins are rated for 2 kV, except for the IMAX pin (Pin 7) which is rated for 1.5 kV. Block Diagram DS100834-2 Test Circuit DS100834-4 FIGURE 2. www.national.com 6 For example, if the desired switching frequency is 300 kHz, the resistance should be around 84 kΩ. OVERVIEW The LM2636 is a high speed synchronous PWM buck regulator controller designed for VRM vendors or motherboard manufacturers who need to build on-board power supplies for Cyrix MII, Pentium II or Deschutes microprocessors. It has a built-in 5-bit DAC to decode the 5-bit word provided by the CPU and supply the corresponding voltage. It also has the power good (PWRGD) and output enable (OUTEN) functions required by the VRM specification. It employs a voltage mode control scheme plus two fast responding comparators to quickly respond to large load transients. It has two fast FET drivers to drive the high-side and low-side NMOS switches of a synchronous buck regulator. The PWM frequency is adjustable from 50 kHz to 1 MHz through an external resistor. Over-voltage protection is achieved by shutting off the high-side driver and turning on the low-side driver 100% of the time. Current limiting is implemented by sensing VDS of the high-side NMOS switch and shutting it off for the present switching cycle when an over current condition is detected. Soft start functionality is realized through an internal digital counter and an internal DAC. The minimum allowable PWM frequency is 5 kHz. MOSFET Gate Drive The LM2636 has two gate drives that are suitable for driving external N-MOSFETs in a synchronous buck topology. The power for the two FET drivers is supplied by the BOOTV pin. This BOOTV voltage needs to be at least one VGS(th) higher than the converter input voltage for the high side FET to be fully turned on. The voltage can be either supplied from a separate source other than the input voltage or can be generated locally by utilizing a charge pump structure. In a typical desktop microprocessor application, if 5V is chosen to be the input voltage, then 12V can be used for the BOOTV. If 12V is not available, a simple charge pump circuitry consisting of a diode and a small capacitor can be used, as shown in Figure 3. THEORY OF OPERATION Start Up When VCC voltage exceeds 4.2V, OUTEN pin is a logic high and the VID code is valid, the soft start circuitry starts to work. The duration of the soft start is determined by an internal digital counter and the switching frequency. During soft start, the output of the error amplifier is allowed to increase gradually. When the counter has counted 2,048 clock cycles, the soft start session ends and the output voltage level of the error amplifier is released and allowed to go to a value that is determined by the feedback loop. PWRGD pin is forced low during soft start and is turned over to output voltage monitoring circuitry after that. Before VCC reaches 4.2V, all internal logic is in a power on reset state and the two FET drivers are disabled. During normal operation, if VCC voltage drops below 3.8V, the internal circuitry will go into power on reset again. The hysteresis helps decrease the noise sensitivity on the VCC pin. After soft starts ends and during normal operation, if the converter output voltage exceeds 115% of the DAC output voltage, the LM2636 will lock into over voltage protection mode. The high side drive will be disabled, and the low side drive will be high. There are two ways to clear the mode. One is to cycle VCC voltage once. The other is to toggle the OUTEN level. After the over voltage protection mode is cleared, the LM2636 will enter the soft start session and start over. DS100834-6 FIGURE 3. BOOTV Voltage Supplied by a Charge Pump When the low side FET is on, the charge pump capacitor is charged to near the input voltage through the diode. When low side FET is turned off, the high side FET driver is enabled, and the charge pump capacitor starts to charge the high side FET gate until it is fully on. By this time the high side FET source node will fly to close to input voltage level and the upper node of the capacitor will also fly to one input voltage higher than the input voltage, enabling the high side FET driver to continue working. For a BOOTV of 12V, the initial gate charging current is typically 2A, and the initial gate discharging current is typically 6A, good for high speed switching. The LM2636 gate drives are of BiCMOS design. Unlike some other bipolar VRM control ICs, the gate drive has railto-rail swing that ensures no spurious turn-on due to capacitive coupling. Another feature of the FET gate drives is the adaptive nonoverlapping mechanism. A gate driver is not turned on until the other is fully off. The dead time in between is typically 20 ns. This avoids the potential shoot-through problem and helps improve efficiency. Normal Operation During the normal operation mode, the LM2636 regulates the converter output voltage by adjusting the duty ratio. The output voltage is determined by the 5-bit VID code set by the user/load. The PWM frequency is set by the external resistor between FREQ_ADJ pin and ground. The resistance needed for a desired switching frequency is: Load Transient Response In a typical modern MPU application such as the Pentium II core voltage power supply, load transient response is a critical issue. The LM2636 utilizes the conventional voltage feedback technology as the primary feedback control method. When the load transient happens, the error in the output voltage level is fed to the error amplifier. The output of 7 www.national.com LM2636 Applications Information LM2636 Applications Information For example, if we know that the rDS_ON of the MOSFET is 20 mΩ, and the current limit we want to set is 20A, then we should choose the value of RIMAX to be 2.2 kΩ. (Continued) the error amplifier is then compared with an internally generated PWM ramp signal and the result of the comparison is a series of pulses with certain duty ratios. These pulses are used to control the turn-on and turn-off of the MOSFET gate drivers. In this way, the error in the output voltage gets “compensated” or cancelled by the change in the duty ratio of the FET switches. During a large load transient, depending on the compensation design, the change in duty ratio can be as fast as less than one switching cycle. Refer to Design Considerations section for more details. To provide the greatest protection over the high side MOSFET, cycle by cycle protection is implemented. The sampling of the VDS starts as early as about 300 ns after the switch is turned on. Whenever an over current condition is detected, the high side switch is immediately turned off and the low side switch turned on, until the next switching cycle comes. The delay of 300 ns is to circumvent switching noise when the MOSFET is first turned on. DESIGN CONSIDERATIONS Besides the usual voltage mode feedback control loop, the LM2636 also has a pair of fast comparators (the MIN and MAX comparators) to help maintain the output voltage during a large and fast load transient. The trip points of the comparators are set to ± 5% of the DAC output voltage. When the load transient is so large that the output voltage goes outside the ± 5% window, the MIN or MAX comparator will bypass the primary voltage control loop and immediately set the duty ratio to either maximum value or to zero. This provides the fastest possible way to react to such a large load transient in a classical buck converter. Control Loop Compensation A switching regulator should be properly compensated to achieve a stable condition. For a synchronous buck regulator that needs to meet stringent load transient requirement such as a Pentium II MPU core voltage supply, a simple 2-pole-1-zero compensation network should suffice, such as the one shown in Figure 4 (C1, C2, R1 and R2). This is because the ESR zero of the typical output capacitors is low enough to make the control-to-output transfer function a single-pole-roll-off. As an example, let us figure out the values of the compensation network components in Figure 4. Assume the following parameters: R = 20Ω, RL = 20 mΩ, RC = 9 mΩ, L = 2 µH, C = 7.5 mF, VIN = 5V, Vm = 2V and switching frequency = 300 kHz. These parameters are based on the typical application in Figure 1. Notice RL is the sum of the inductor DC resistance and the on resistance of the MOSFETs. Power Good Signal The power good signal is used to indicate that the output voltage is within specified range. In the LM2636, the range is set to a ± 10% window of the DAC output voltage. During soft start, the power good signal is always low. At the end of the soft start session,the output voltage is checked and the PWRGD pin will be asserted if the voltage is within specified range. Over Voltage Protection When the output voltage exceeds 115% of the DAC output voltage after the end of soft start, the LM2636 will enter over voltage protection mode in which it shuts itself down. The upper gate driver is held low while the lower gate driver is held high. PWRGD will be low. For LM2636 to recover from OVP mode, either OUTEN or VCC voltage has to be toggled. Another more subtle way to recover is to float all the VID pins and reapply the correct code. Current Limit Current limit is realized by sensing the VDS voltage of the high side MOSFET when it is on. Since the rDS_ON of a MOSFET is a known value, current through the MOSFET can be known by monitoring VDS. The relationship between the three parameters is: DS100834-9 To implement the current limit function, an external resistor RIMAX is need. The resistor should be connected between the drain of the high side MOSFET and the IMAX pin. A constant current of around 180 µA is forced into the IMAX pin and causes a fixed voltage drop across the RIMAX resistor. This voltage drop is then compared with the VDS of the high side MOSFET and if the latter is higher, over current is reached. So the appropriate value of RIMAX for a predetermined current limit level ILIM can be calculated by the following equation: www.national.com FIGURE 4. Buck Converter from a Control Point of View 8 LM2636 Applications Information (Continued) The control-to-output transfer function is where The ESR zero frequency is: One of the poles is located at origin to help achieve the highest DC gain. So there are three parameters to determine, the position of the zero, the position of the second pole, and the constant A. To determine the cutoff frequency and phase margin, the loop bode plots need to be generated. The loop transfer function is: The power stage double pole frequency is: TF = −TF1 x TF2 By choosing the zero close to the double pole position and the second pole to half of the switching frequency, the closed loop transfer function turns out to be very good. That is, if fZ = 1.32 kHz, fP = 153 kHz, and A = 4.8 x 10−6 ΩF, then the cutoff frequency will be 50 kHz, the phase margin will be 72˚, and the DC gain will be that of the error amplifier. See Figure 6 below. The corresponding Bode plots are shown in Figure 5. DS100834-13 FIGURE 5. Control-to-Output Bode Plots Since the ESR zero frequency is so low, it effectively cancels the phase shift from one of the power stage poles. This limits the total phase shift to 90%. Although this regulator design is stable (phase shift is < 90˚ when gain = 0dB), it needs compensation to improve the DC gain and cut off frequency (0dB frequency). Otherwise, the low DC gain may cause a poor line regulation, and the low cutoff frequency will hurt transient response performance. The transfer function for the 2-pole-1-zero compensation network shown in Figure 4 is: DS100834-17 FIGURE 6. Loop Bode Plots The compensation network component values can be determined by the following equations: Notice there are three equations but four variables. So one of the variables can be chosen arbitrarily. Since the current driving capability of the error amplifier is limited to around 3 mA, it is a good idea to have a high impedance path from the output of the error amplifier to the output of the converter. From the above equations it can be told that a larger R2 will 9 www.national.com LM2636 Applications Information to quickly supply current to the output capacitors when the load suddenly kicks in and to quickly stop supplying current when the load is suddenly removed. Multilayer ceramic (MLC) capacitors can have very low ESR but also a low capacitance value compared to other kinds of capacitors. Low ESR aluminum electrolytic capacitors tend to have large sizes and capacitances. Tantalum electrolytic capacitors can have a fairly low ESR with a much smaller size and capacitance than the aluminum capacitors. Certain OSCON capacitors present ultra low ESR and long life span. By the time the total ESR of the output capacitor bank reaches around 9 mΩ, the capacitance of the aluminum/ tantalum/OSCON capacitors is usually already in the millifarad range. For those capacitors, ESR is the only factor to consider. MLCs can have the same amount of total ESR with much less capacitance, most probably under 100 µF. A very small inductor, ultra fast control loop and a high switching frequency become necessary in such a case to deal with the fast charging/discharging rate of the output capacitor bank. From a cost savings point of view, aluminum electrolytic capacitors are the most popular choice for output capacitors. They have reasonably long life span and they tend to have huge capacitance to withstand the charging or discharging process during a load transient for a fairly long period. Sanyo MV-GX series gives good performance when enough of the capacitors are paralleled. The 6MV1500GX capacitor has a typical ESR of 44 mΩ. Five of these capacitors should be sufficient in the case of on-board power supply for a Pentium II motherboard. The challenge for input capacitors is the ripple current. The large ripple current drawn by the high side switch tends to generate quite some heat due to the capacitor ESR. The ripple current ratings in the capacitor catalogs are usually specified under the highest allowable temperature. In the case of desktop applications, those ratings seem too conservative. A good way to ensure enough number of capacitors is through lab evaluation. The input current RMS ripple value can be determined by the following equation: (Continued) result in a smaller C1, C2 and a larger R1. However, too large an R1 can also bring error due to the bias current required by the inverting input pin of the error amplifier. Calculations show that the following combination is a good one: R2 = 51Ω, C1 = 0.022 µF, R1 = 5.6 kΩ, C2 = 820 pF. For a different application or different type of output capacitors, a different compensation scheme may be necessary. The user can either follow the steps above to figure the appropriate component values or contact the factory for help. MOSFET SELECTION The selection of MOSFET switches affects both the efficiency of the whole converter and the current limit setting. From an efficiency point of view it is suggested that for the high-side switch, only logic level MOSFETs be used. Standard MOSFETs can be used for the low side switch when 12V is used to power the BOOTV pin. The lower loss associated with the MOSFETs is two-fold — Ohmic loss and switching loss. The Ohmic loss is easy to calculate whereas the switching loss is much more difficult to estimate. In general the switching loss is directly proportional to the switching frequency. As the power MOSFET technology advances, lower and lower gate charge devices will be available. That should allow the user to go to higher switching frequencies without the penalty of losing too much efficiency. As an example, let us select the MOSFETs for a converter with a target efficiency of 80% at a load of 2.8V, 14A. Assume the inductors lose 1W, the capacitors lose 0.75W and the total switching loss at 300 kHz is 3.2W. The total allowed power loss is 9.8W, so the MOSFET Ohmic loss should not exceed 4.9W. Assume the two switches have the same conduction loss, i.e., 2.5W each, then the ON resistance for the two switches is: and the power loss in each input capacitor is: The low side switch ON resistance is much higher than the high side because at 2.8V the duty cycle is higher than 50% and becomes even larger at full load. For the high side switch, an IRL3202 (TO-220 package) or IRL3202S (D2PAK) should be sufficient. For the low side switch, an IRL3303 (TO-220 package) or IRL3303S (D2PAK) should be sufficient. Since each FET is dissipating 3.2W/2 + 2.5W = 4.1W, it is suggested that appropriate heat sinks be used in the case of TO-220 package or large enough copper area be connected to the drain in the case of surface mount package. In the case of Pentium II power supply, the maximum output current is around 14A. Under the worst case when duty cycle is 50%, the maximum input capacitor RMS ripple current is half of output current, i.e., 7A. It is found that three Sanyo 16MV820GX capacitors are enough under room temperature. The typical ESR of those capacitors is 44 mΩ. So the power loss in each of them is around (7A)2 x 44 mΩ/32 = 0.24W. Note that the power loss in each capacitor is inversely proportional to the square of the total number of capacitors, which means the power loss in each capacitor quickly drops when the number of capacitors increases. CAPACITOR SELECTION The selection of capacitors is an extremely important step when designing a converter for a load such as the Pentium II. Since the typical slew rate of the load current during a large load transient is around 20A/µs to 30A/µs, the switching converter has to rely on the output capacitors to take care of the first few microseconds. Under such a current slew rate, ESR of the output capacitors is more of a concern than the ESL. Depending on the kind of capacitors being used, capacitance of the output capacitors may or may not be an important factor. When the output capacitance is too low, the converter may have to have a small output inductor www.national.com INDUCTOR SELECTION The size of the output is determined by a number of parameters. Basically the larger the inductor, the smaller the output ripple voltage, but the slower the converter’s response speed during a load transient. On the other hand, a smaller inductor requires higher switching frequency to maintain the same level of output ripple, and probably results in a more lossy converter, but has less inertia responding to load tran10 where (di/dt)MAX is the maximum allowable input current slew rate, which is 0.1A/µs in the case of the Pentium II power supply. So the input inductor size, according to the above equation, should be 2.1 µH. (Continued) sient. In the case of Pentium II power supply, fast recovery of the load voltage from transient window back to the steady state window is considered important. This limits the highest inductance value that can be used. The lowest inductance value is limited by the highest switching frequency that can be practically employed. As the switching frequency increases, the switching loss in the MOSFETs tends to increase, resulting in less converter efficiency and larger heat sinks. A good switching frequency is probably a frequency under which the MOSFET conduction loss is higher than the switching loss because the cost of the MOSFET is directly related to its RDSON. The inductor size can be determined by the following equation: DYNAMIC POSITIONING OF LOAD VOLTAGE Since the Intel VRM specifications have defined two operating windows for the MPU core voltage, one being the steady state window and the other the transient window, it is a good idea to dynamically position the steady state output voltage in the steady state window with respect to load current level so that the output voltage has more headroom for load transient response. This requires information about the load current. There are at least two simple ways to implement this idea with LM2636. One is to utilize the output inductor DC resistance, see Figure 7. The average voltage across the output inductor is actually that across its DC resistance. That average voltage is proportional to load current. Since the switching node voltage VA bounces between the input voltage and ground at the switching frequency, it is impossible to choose point A as the feedback point, otherwise the dynamic performance will suffer and the system may have some noise problems. Using a low pass filter network around the inductor, such as the one shown in the figure, seems to be a good idea. The feedback point is C. where VO_RIP is the peak-to-peak output ripple voltage, f is the switching frequency. For commonly used low RDSON MOSFETs, a reasonable switching frequency is 300 kHz. Assume an output peak-peak ripple voltage of 18 mV is to be guaranteed, the total output capacitor ESR is 9 mΩ, the input voltage is 5V, and output voltage is 2.8V. The inductance value according to the above equation will then be 2 µH. The highest slew rate of the inductor current when the load changes from no load to full load can be determined as follows: where DMAX is the maximum allowed duty cycle, which is around 0.9 for LM2636. For a load transient from 0A to 14A, the highest current slew rate of the inductor, according to the above equation, is 0.85A/µs, and therefore the shortest possible total recovery time is 14A/(0.85A/µs) = 16.5 µs. Notice that the output voltage starts to recover whenever the inductor starts to supply current. The highest slew rate of the inductor current when the load changes from full load to no load can be determined from the same equation, but use DMIN instead of DMAX. Since the DMIN of LM2636 at 300 kHz is 0%, the slew rate is therefore −1.4A/µs. So the approximate total recovery time will be 14A/(1.4A/µs) = 10 µs. The input inductor is for limiting the input current slew rate during a load transient. In the case that low ESR aluminum electrolytic capacitors are used for the input capacitor bank, voltage change due to capacitor charging/discharging is usually negligible for the first 20 µs. ESR is by far the dominant factor in determining the amount of capacitor voltage undershoot/overshoot due to load transient. So the worst case is when the load changes between no load and full load, under which condition the input inductor sees the highest voltage change across the input capacitors. Assume the input capacitor bank is made up of three 16MV820GX, i.e., the total ESR is 15 mΩ. Whenever there is a sudden load current change, it has to initially be supported by the input capacitor bank instead of the input inductor. So for a full load swing between 0A and 14A, the voltage seen by the input inductor is ∆V = 14A x 15 mΩ = 210 mV. Use the following equation to determine the minimum inductance value: DS100834-26 FIGURE 7. Dynamic Voltage Positioning by Utilizing Output Inductor DC Resistance Since at the switching frequency the impedance of the 0.1 µF is much less than 5 kΩ, the bouncing voltage at point A will be mainly applied across the resistor 5 kΩ, and point C will be much quieter than A. However, VCB average is still the majority of VAB average, because of the resistor divider. So in steady state VC = IO x rL + VCORE, where rL is the inductor DC resistance. So at no load, output voltage is equal to VC, and at full load, output voltage is IO x rL lower than VC. To further utilize the steady state window, a resistor can be connected between the FB pin and ground to increase the no load output voltage to close to the upper limit of the window. 11 www.national.com LM2636 Applications Information LM2636 Applications Information REFERENCE VOLTAGE The VREF pin can have many uses, such as in the watchdog circuitry and in an LDO controller. Figure 9 shows an application where VREF is used to build a N-FET LDO controller. An appropriate compensation network is necessary to tailor the dynamic performance of the whole power supply. (Continued) DS100834-28 DS100834-27 FIGURE 9. VREF Used in an N-FET LDO Supply FIGURE 8. Dynamic Voltage Positioning by Using A Stand-Alone Resistor PCB LAYOUT CONSIDERATIONS There are several points to consider. A possible drawback of the scheme in Figure 7 is slow transient recovery speed. Since the 5 kΩ resistor and the 0.1 µF capacitor have a large time constant, the settling of point C to its steady state value during a load transient may take a few milliseconds. Depending on the interaction between the compensation network and the 0.1 µF capacitor, Vcore may take different routes to reach its steady state value. This is undesired when the load transients happens more than 1000 times per second. Reducing the time constant will result in a more fluctuating VC due to a less effective low pass filter. Fine tuning the parameters may balance the tradeoffs. Another way to implement the dynamic voltage positioning is through the use of a stand-alone resistor, such as the 4 mΩ resistor in Figure 8 above. The advantage of this implementation over the previous one is a much faster speed of VCORE from transient level to steady state level. The disadvantage is less efficiency. The total power loss can be 0.78W at 14A of load current. The cost of the resistor can be minimized by implementing it through a PCB trace. 1. 2. 3. 4. 5. 6. 7. www.national.com 12 Try to use 2 oz. copper for the ground plane if tight load regulation is desired. In the case of dynamic voltage positioning, this may not be a concern because the loose load regulation is desired anyway. However, do not forget to take into consideration the voltage drop caused by the ground plane when calculating dynamic voltage positioning parameters. Try to keep gate traces short. However, do not make them too short or else the LM2636 may stay too close to the MOSFETs and get heated up by them. For the same reason, do not use wide traces, 10 mil traces should be enough. When not employing dynamic voltage positioning, place the feedback point at the VRM connector pins to have a tight load regulation. If it is an on-board power supply, place the feedback point at Slot I connector or wherever is closest to the MPU. Start component placement with the power devices such as MOSFETs and inductors. Do not place the LM2636 directly underneath the MOSFETs when when surface mount MOSFETs are used. If possible, keep the capacitors some distance away from the inductors so that the capacitors will have a lower temperature environment. When implementing dynamic voltage positioning through a PCB trace, be aware that the PCB trace is a heat source and try to avoid placing the trace directly underneath the LM2636. LM2636 Physical Dimensions inches (millimeters) unless otherwise noted 20-Lead Plastic SO Package Order Number LM2636M NS Package Number M20B 13 www.national.com LM2636 5-Bit Programmable Synchronous Buck Regulator Controller Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 20-Lead Plastic TSSOP (MTC) Order Number LM2636MTC NS Package Number MTC20 LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: [email protected] www.national.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Français Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: [email protected] National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. WWW.ALLDATASHEET.COM Copyright © Each Manufacturing Company. All Datasheets cannot be modified without permission. This datasheet has been download from : www.AllDataSheet.com 100% Free DataSheet Search Site. Free Download. No Register. Fast Search System. www.AllDataSheet.com