LM3743 High-Performance Synchronous Buck Controller with Comprehensive Fault Protection Features General Description Features The LM3743 is a DC-DC voltage mode PWM buck controller featuring synchronous rectification at 300 kHz or 1 MHz. It can deliver current as high as 20A and step down from an input voltage between 3V and 5.5V down to a minimum output voltage of 0.8V, with a ±1.75% internal reference accuracy. The LM3743 provides a set of comprehensive fault protection features such as high-side current limit, output under-voltage protection, and low-side current limit. When any of these fault protection features are engaged, it enters a hiccup protection mode which is suitable for high reliability systems such as rack mounted servers and telecom base station subsystems. The LM3743 also employs a proprietary monolithic glitch free pre-bias start-up method suited for FPGA and ASIC logic devices. An external programmable soft-start allows for tracking and timing flexibility. The driver features 1.6Ω of pull-up resistance and 1Ω of pull-down drive resistance for high power density and very efficient power processing. ■ Input voltage from 3.0V to 5.5V ■ Output voltage adjustable down to 0.8V ■ Reference accuracy: ±1.75%, over full temperature and input voltage range ■ High-side and Low-side N-Channel MOSFETs ■ Switching frequency options of 1 MHz or 300 kHz ■ Comprehensive Fault Protection Features: ■ ■ ■ ■ High-side current limit Low-side current limit Output under-voltage protection Hiccup mode protection eliminates thermal runaway during fault conditions Externally programmable soft-start with tracking capability Pre-bias start-up capability MSOP-10 package Applications ■ ■ ■ ■ ■ ■ Rack-mount servers Telecom base stations Routers Printers/Scanners Multi-media set-top boxes FPGAs, ASICs, and DSPs Typical Application 20177401 © 2008 National Semiconductor Corporation 201774 www.national.com LM3743 High-Performance Synchronous Buck Controller with Comprehensive Fault Protection Features October 7, 2008 LM3743 Connection Diagram 20177402 10-Lead Plastic MSOP NS Package Number MUB10A Top View Ordering Information Frequency Option Top Mark NSC Package Drawing LM3743MM-300 Order Number 300 kHz SKPB MUB10A Supplied As 1000 units in Tape and Reel LM3743MMX-300 300 kHz SKPB MUB10A 3500 units in Tape and Reel LM3743MM-1000 1 MHz SKNB MUB10A 1000 units in Tape and Reel LM3743MMX-1000 1 MHz SKNB MUB10A 3500 units in Tape and Reel Pin Descriptions VCC (Pin 1) Supply rail for the controller section of the IC. A minimum capacitance of 1 µF, preferably a multi-layer ceramic capacitor type (MLCC), must be connected as close as possible to the VCC and GND pin and a 1 to 4.99Ω resistance must be connected in series from the supply rail to the Vcc pin. See VCC FILTERING in the Design Consideration section for further details. LGATE (Pin 2) Gate drive for the low-side N-channel MOSFET. This signal is interlocked with HGATE to avoid a shootthrough problem. GND (Pin 3) Power ground (PGND) and signal ground (SGND). Connect the bottom feedback resistor between this pin and the feedback pin. ILIM (Pin 4) Low side current limit threshold setting pin. This pin sources a fixed 50 µA current. A resistor of appropriate value should be connected between this pin and the drain of the low-side N-FET. FB (Pin 5) Feedback pin. This is the inverting input of the error amplifier used for sensing the output voltage and compensating the control loop. COMP/EN (Pin 6) Output of the error amplifier and enable pin. The voltage level on this pin is compared with an internally www.national.com generated ramp signal to determine the duty cycle. This pin is necessary for compensating the control loop. Forcing this pin to ground will shut down the IC. SS/TRACK (Pin 7) Soft-start and tracking pin. This pin is connected to the non-inverting input of the error amplifier during initial soft-start, or any time the voltage is below the reference. To track the rising ramp of another power supply's output, connect a resistor divider from the output of that supply to this pin as described in Application Information. SW (Pin 8) Switch pin. The lower rail of the high-side N-FET driver. Also used for the high side current limit sensing. HGATE (Pin 9) Gate drive for the high-side N-channel MOSFET. This signal is interlocked with LGATE to avoid a shootthrough problem. BOOT (Pin 10) Supply rail for the N-channel MOSFET high gate drive. The voltage should be at least one gate threshold above the regulator input voltage to properly turn on the highside N-FET. See MOSFET Gate Drivers in the Application Information section for more details on how to select MOSFETs. 2 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. VCC SW to GND Boot to GND Boot to SW SS/TRACK, ILIM, COMP/EN,FB to GND Junction Temperature Storage Temperature Lead Temperature (soldering, 10sec) 260°C Infrared or Convection (20sec) ESD Rating (Note 3) -0.3V to 6V -0.3V to 6V -0.3V to 12V -0.3V to 6V 235°C + / – 2 kV Operating Ratings Supply Voltage Range, VCC (Note 2) Junction Temperature Range (TJ) -0.3V to VCC 150°C −65°C to 150°C 3.0V to 5.5V −40°C to +125°C Electrical Characteristics VCC = 3.3V, COMP/EN floating unless otherwise indicated in the conditions column. Limits in standard type are for TJ = 25°C only; limits in boldface type apply over the junction temperature (TJ) range of -40°C to +125°C. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference purposes only. Symbol Parameter Conditions Min Typ Max Units 0.786 0.8 0.814 V 2.84 3.0 SYSTEM PARAMETERS VFB VUVLO FB pin voltage in regulation 3.0V ≤ VCC ≤ 5.5V UVLO thresholds Input voltage rising Input voltage falling IVCC ISS/TRACK 2.45 2.66 V Operating VCC current fSW = 300 kHz, LM3743-300 1.5 2.5 mA Operating VCC current fSW = 1 MHz, LM3743-1000 1.8 3.0 mA Shutdown VCC current COMP/EN = 0V 6 50 µA SS/TRACK pin source current VSS/TRACK = 0V IILIM ILIM pin source current VILIM = 0V VILIM Current Limit Trip Level ICOMP/EN COMP/EN pin pull-up current VCOMP/EN = 0V VHS-CLIM High-side current limit threshold Measured at VCC pin with respect to SW 8 10.2 12.5 µA 42.5 50 57.5 µA –25 0 25 mV 4 µA 500 mV Error Amplifier Unity Gain Bandwidth 30 MHz Error Amplifier DC Gain 90 dB 0.5 V/µs ERROR AMPLIFER GBW G SR Error Amplifier Slew Rate IFB FB pin Bias Current 10 EAO pin sourcing/sinking current capability VCOMP/EN = 1.5, VFB = 0.75V 1.7 VCOMP/EN = 1.5, VFB = 0.85V -1 IEAO CCOMPENSATION = 2.2 nF, IEAO = 1 mA 200 nA mA GATE DRIVE ISHDN-BOOT BOOT Pin Shutdown Current VBOOT-VSW = 3.3V, VCOMP/EN = 0V 25 RHG-UP High Side MOSFET Driver Pull-up ON resistance VBOOT-VSW = 3.3V, IHGATE = 350mA (sourcing) 1.6 Ω RHG-DN High Side MOSFET Driver Pull-down ON resistance VBOOT-VSW = 3.3V, IHGATE = 350mA (sinking) 1 Ω RLG-UP Low Side MOSFET Driver Pull-up ON resistance VCC = 3.3V, ILGATE = 350mA (sourcing) 1.6 Ω RLG-DN Low Side MOSFET Driver Pull-down ON resistance VCC = 3.3V, ILGATE = 350mA (sinking) 1 Ω 50 µA OSCILLATOR fSW DMAX Oscillator Frequency Max Duty Cycle 3.0V ≤ VCC ≤ 5.5V, LM3743-300 255 300 345 3.0V ≤ VCC ≤ 5.5V, LM3743-1000 850 1000 1150 fSW = 300 kHz, LM3743-300 85 91 fSW = 1 MHz, LM3743-1000 69 76 3 kHz % www.national.com LM3743 Soldering Information Absolute Maximum Ratings (Note 1) LM3743 Symbol VRAMP Parameter Conditions Min PWM Ramp Amplitude Typ Max 1.0 Units V LOGIC INPUTS AND OUTPUTS VCOMP/EN-HI COMP/EN pin logic high trip-point 0.65 VCOMP/EN-LO COMP/EN pin logic low trip-point 0.9 V 0.45 V NLSCYCLES Low-side sensing cycles before hiccup mode 15 Cycles NLSRESET Low-side sensing cycles reset without activating current limit 32 Cycles VUVP Under Voltage Protection comparator threshold 400 mV 7 µs Hiccup timeout 5.5 ms Soft-start time coming out of hiccup mode 3.6 ms 235 °C/W 0.1 HICCUP MODE tGLICH-UVP tHICCUP tSS Under Voltage Protection fault time before hiccup mode THERMAL RESISTANCE θJA Junction to Ambient Thermal Resistance Note 1: Absolute maximum ratings indicate limits beyond which damage to the device may occur. Operating ratings indicate conditions for which the device operates correctly. Operating Ratings do not imply guaranteed performance limits. Note 2: Practical lower limit of VCC depends on selection of the external MOSFET. See the MOSFET GATE DRIVERS section under Application Information for further details. Note 3: ESD using the human body model which is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin. Test method is per JESD22–A114. www.national.com 4 LM3743 Block Diagram 20177403 5 www.national.com LM3743 Typical Performance Characteristics VIN = 3.3, TJ = 25°C, ILOAD = 1A unless otherwise specified. DMax vs Temperature fSW = 1 MHZ DMax vs Temperature fSW = 300 kHz 20177455 20177456 FB vs Temperature fSW = 1 MHZ FB vs Temperature fSW = 300 kHz 20177457 20177458 Frequency vs Temperature fSW = 1 MHz Frequency vs Temperature fSW = 300 kHz 20177459 www.national.com 201774a2 6 LM3743 Frequency vs VCC fSW = 1 MHz Frequency vs VCC fSW = 300 kHz 20177461 20177462 ISHDN_BOOT vs Temperature fSW = 1 MHz ISHDN_BOOT vs Temperature fSW = 300 kHz 20177463 20177464 ILIM vs Temperature fSW = 1 MHz ILIM vs Temperature fSW = 300 kHz 20177465 20177466 7 www.national.com LM3743 IVCC vs Temperature fSW = 1 MHz IVCC vs Temperature fSW = 300 kHz 20177467 20177468 Line Regulation VOUT = 1.2V, IOUT = 1A, fSW = 300 kHz Line Regulation VOUT = 1.5V, IOUT = 1A, fSW = 1 MHz 20177469 20177470 Load Regulation VIN = 3.3V, fSW = 1 MHz Load Regulation VIN = 3.3V, fSW = 300 kHz 20177471 www.national.com 20177472 8 LM3743 Efficiency vs Load fSW = 300 kHz, VIN = 5.0V (Refer to Example Circuit 1) Efficiency vs Load fSW = 300 kHz, VOUT = 2.5V (Refer to Example Circuit 2) 201774a3 201774a4 Efficiency vs Load fSW = 300 kHz, VIN = 5.0V (Refer to Example Circuit 1) Efficiency vs Load fSW = 300 kHz, VOUT = 1.8V (Refer to Example Circuit 2) 201774a5 201774a6 Efficiency vs Load fSW = 300 kHz, VOUT = 3.3V (Refer to Example Circuit 2) Efficiency vs Load fSW = 300 kHz, VOUT = 1.5V (Refer to Example Circuit 2) 201774a7 201774a8 9 www.national.com LM3743 Efficiency vs Load fSW = 300 kHz, VOUT = 1.2V (Refer to Example Circuit 2) Efficiency vs Load fSW = 300 kHz, VOUT = 1.0V (Refer to Example Circuit 2) 201774a9 201774b0 Efficiency vs Load fSW = 300 kHz, VOUT = 0.8V (Refer to Example Circuit 2) Efficiency vs Load fSW = 1 MHz, VOUT = 2.5V (Refer to AN-1450 for BOM) 201774b1 20177489 Efficiency vs Load fSW = 1 MHz, VOUT = 1.8V (Refer to AN-1450 for BOM) Efficiency vs Load fSW = 1 MHz, VOUT = 1.5V (Refer to AN-1450 for BOM) 20177488 www.national.com 20177487 10 LM3743 Efficiency vs Load fSW = 1 MHz, VOUT = 1.2V (Refer to AN-1450 for BOM) Efficiency vs Load fSW = 1 MHz, VOUT = 1.0V (Refer to AN-1450 for BOM) 20177474 20177473 Efficiency vs Load fSW = 1 MHz, VOUT = 0.8V (Refer to AN-1450 for BOM) Efficiency vs Load fSW = 300 kHz, VOUT = 2.5V (Refer to AN-1450 for BOM) 20177490 20177495 Efficiency vs Load fSW = 300 kHz, VOUT = 1.8V (Refer to AN-1450 for BOM) Efficiency vs Load fSW = 300 kHz, VOUT = 1.5V (Refer to AN-1450 for BOM) 20177494 20177493 11 www.national.com LM3743 Efficiency vs Load fSW = 300 kHz, VOUT = 1.2V (Refer to AN-1450 for BOM) Efficiency vs Load fSW = 300 kHz, VOUT = 1.0V (Refer to AN-1450 for BOM) 20177492 20177491 Efficiency vs Load fSW = 300 kHz, VOUT = 0.8V (Refer to AN-1450 for BOM) Load Transient Response fSW = 1 MHz, VIN = 3.3V, ILOAD = 100 mA to 3.5A (Refer to AN-1450 for BOM) 20177497 20177496 Load Transient Response fSW = 300 kHz, VIN = 3.3V, ILOAD = 100 mA to 3.5A (Refer to AN-1450 for BOM) Shutdown RLOAD = 1Ω, VIN = 5V 20177499 20177498 www.national.com 12 LM3743 Pre Bias Startup 201774a0 13 www.national.com LM3743 start voltage, VOUT, and the internal voltage ramp. Any further commutation of the load current is carried by the body diode of the low-side FET or an external Schottky diode, if used. The low side current limit is active during soft-start while allowing the asynchronous switching. When soft-start is completed, the on-time of the low-side FET is allowed to increase in a controlled fashion up to the steady state duty cycle determined by the control loop. A plot of the LM3743 starting up into a pre-biased condition is shown in the Typical Performance Characteristics section. Note that the pre-bias voltage must not be greater than the target output voltage of the LM3743, otherwise the LM3743 will pull the pre-bias supply down during steady state operation. Application Information THEORY OF OPERATION The LM3743 is a voltage mode PWM buck controller featuring synchronous rectification at 300 kHz or 1 MHz. In steady state operation the LM3743 is always synchronous even at no load, thus simplifying the compensation design. The LM3743 ensures a smooth and controlled start-up to support pre-biased outputs. Two levels of current limit protection enhance the robustness of the power supply and requires no current sense resistor in the power path. The primary level of protection is the low side current limit and is achieved by sensing the voltage VDS across the low side MOSFET. The second level of protection is the high side current limit, which protects power components from extremely high currents, caused by switch node short to ground. TRACKING WITH EQUAL SOFT-START TIME The LM3743 can track the output of a master power supply during soft-start by connecting a resistor divider to the SS/ TRACK pin. In this way, the output voltage slew rate of the LM3743 will be controlled by the master supply for loads that require precise sequencing. When the tracking function is used, no soft-start capacitor should be connected to the SS/ TRACK pin. However in all other cases, a capacitor value (C4) of at least 560 pF should be connected between the soft-start pin and ground. NORMAL OPERATION While in normal operation, the LM3743 IC controls the output voltage by controlling the duty cycle of the power FETs. The DC level of the output voltage is determined by a pair of feedback resistors using the following equation: (Designators refer to the Typical Application Circuit in the front page) For synchronous buck regulators, the duty ratio D is approximately equal to: START UP The LM3743 IC begins to operate when the COMP/EN pin is released from a clamped condition and the voltage at the VCC pin has exceeded 2.84V. Once these two conditions have been met the internal 10µA current source begins to charge the soft-start capacitor connected at the SS/TRACK pin. During soft-start the voltage on the soft-start capacitor is connected internally to the non-inverting input of the error amplifier. The soft-start period lasts until the voltage on the soft-start capacitor exceeds the LM3743 reference voltage of 0.8V. At this point the reference voltage takes over at the noninverting error amplifier input. The capacitance determines the length of the soft-start period, and can be approximated by: 20177430 FIGURE 1. Tracking Circuit One way to use the tracking feature is to design the tracking resistor divider so that the master supply’s output voltage (VOUT1) and the LM3743’s output voltage (represented symbolically in Figure 1 as VOUT2, i.e. without explicitly showing the power components) both rise together and reach their target values at the same time. For this case, the equation governing the values of the tracking divider resistors RT1 and RT2 is: C4 = (tSS x 10 µA) / 0.8V Where tSS is the desired soft-start time. In the event of either VCC falling below UVLO or COMP/EN pin being pulled below 0.45V, the soft-start pin will discharge C4 to allow the output voltage to recover smoothly. START UP WITH PRE-BIAS A pre-bias output is a condition in which current from another source has charged up the output capacitor of the switching regulator before it has been turned on. The LM3743 features a proprietary glitch free monotonic pre-bias start-up method designed to ramp the output voltage from a pre-biased rail to the target nominal output voltage. The IC limits the on time of the low-side FET to 150 ns (typ) during soft-start, while allowing the high-side FET to adjust it's time according to soft- www.national.com The top resistance RT2 must be set to 1 kΩ in order to limit current into the LM3743 during UVLO or shutdown. The final voltage of the SS/TRACK pin should be slightly higher than the feedback voltage of 0.8V, say about 0.85V as in the above equation. The 50 mV difference will ensure the LM3743 to reach regulation slightly before the master supply. If the master supply voltage was 5V and the LM3743 output voltage was 1.8V, for example, then the value of RT1 needed to give the 14 SHUTDOWN The LM3743 IC can be put into shutdown mode by bringing the voltage at the COMP/EN pin below 0.45V (typ). The quiescent current during shutdown is approximately 6 µA (typ). During shutdown both the high-side and low-side FETs are disabled. The soft-start capacitor is discharged through an internal FET so that the output voltage rises in a controlled fashion when the part is enabled again. When enabled a 4 µA pull-up current increases the charge of the compensation capacitors. UNDER VOLTAGE LOCK-OUT (UVLO) If VCC drops below 2.66V (typ), the chip enters UVLO mode. UVLO consists of turning off the top and bottom FETs and remaining in that condition until VCC rises above 2.84V (typ). As with shutdown, the soft-start capacitor is discharged through an internal FET, ensuring that the next start-up will be controlled by the soft-start circuitry. 20177431 FIGURE 2. Tracking with Equal Soft-Start Time TRACKING WITH EQUAL SLEW RATES The tracking feature can alternatively be used not to make both rails reach regulation at the same time but rather to have similar rise rates (in terms of output dV/dt). In this case, the tracking resistors can be determined based on the following equation: MOSFET GATE DRIVE The LM3743 has two gate drivers designed for driving Nchannel MOSFETs in synchronous mode. Power for the high gate driver is supplied through the BOOT pin, while driving power for the low gate is provided through the VCC pin. The BOOT voltage is supplied from a local charge pump structure which consists of a Schottky diode and 0.1 µF capacitor, shown in Figure 4. Since the bootstrap capacitor (C10) is connected to the SW node, the peak voltage impressed on the BOOT pin is the sum of the input voltage (VIN) plus the voltage across the bootstrap capacitor (ignoring any forward drop across the bootstrap diode). The bootstrap capacitor is charged up by VIN (called VBOOT_DC here) whenever the upper MOSFET turns off. For the example case of VOUT1 = 5V and VOUT2 = 1.8V, with RT2 set to 1 kΩ as before, RT1 is calculated from the above equation to be 887Ω. A timing diagram for the case of equal slew rates is shown in Figure 3. 20177433 FIGURE 3. Tracking with Equal Slew Rate TRACKING AND SHUTDOWN SEQUENCING LM3743 is designed to track the output of a master power supply during start-up, but when the master supply powers down the output capacitor of the LM3743 will discharge cycle by cycle through the low-side FET. The off-time will reach 100% when the voltage at the track pin reaches zero volts. This condition will persist as long as the master output voltage is zero volts and the drivers of the LM3743 are still on. For example if the load is required to not be discharged, the 20177434 FIGURE 4. Charge Pump Circuit and Driver Circuitry The output of the low-side driver swings between VCC and ground, whereas the output of the high-side driver swings between VIN + VBOOT_DC and VIN. To keep the high-side MOSFET fully on, the Gate pin voltage of the MOSFET must be higher than its instantaneous Source pin voltage by an 15 www.national.com LM3743 drivers must be shut-off before the master powers down. This is achieved by shutting down the LM3743 or bring VCC below UVLO falling threshold. In this case the load will not be discharged. two supplies identical soft-start times would be 205Ω. A timing diagram for the equal soft-start time case is shown in Figure 2. LM3743 amount equal to the 'Miller plateau'. It can be shown that this plateau is equal to the threshold voltage of the chosen MOSFET plus a small amount equal to IOUT/g. Here IOUT is the maximum load current of the application, and g is the transconductance of this MOSFET (typically about 100 for logic-level devices). That means we must choose VBOOT_DC to at least exceed the Miller plateau level. This may therefore affect the choice of the threshold voltage of the external MOSFETs, and that in turn may depend on the chosen VIN rail. So far in the discussion above, the forward drop across the bootstrap diode has been ignored. But since that does affect the output of the driver, it is a good idea to include this drop in the following examples. Looking at the Typical Application schematic, this means that the difference voltage VIN - VD1, which is the voltage the bootstrap capacitor charges up to, must always be greater than the maximum tolerance limit of the threshold voltage of the upper MOSFET. Here VD1 is the forward voltage drop across the bootstrap diode D1. This voltage drop may place restrictions on the type of MOSFET selected. The capacitor C10 serves to maintain enough voltage between the top MOSFET gate and source to control the device even when the top MOSFET is on and its source has risen up to the input voltage level. The charge pump circuitry is fed from VIN, which can operate over a range from 3.0V to 5.5V. Using this basic method the voltage applied to the high side gate VIN - VD1. This method works well when VIN is 5V±10%, because the gate drives will get at least 4.0V of drive voltage during the worst case of VIN-MIN = 4.5V and VD1-MAX = 0.5V. Logic level MOSFETs generally specify their on-resistance at VGS = 4.5V. When VCC = 3.3V±10%, the gate drive at worst case could go as low as 2.5V. Logic level MOSFETs are not guaranteed to turn on, or may have much higher on-resistance at 2.5V. Sub-logic level MOSFETs, usually specified at VGS = 2.5V, will work, but are more expensive and tend to have higher on-resistance. For example, a conservative 15A current limit (ICLIM) in a 10A design with a RDSON-HOT of 10 mΩ would require a 3.83 kΩ resistor. The LM3743 enters current limit mode if the inductor current exceeds the set current limit threshold. The inductor current is first sampled 50 ns after the low-side MOSFET turns on. Note that in normal operation mode the high-side MOSFET always turns on at the beginning of a clock cycle. In current limit mode, by contrast, the high-side MOSFET onpulse is skipped. This causes inductor current to fall. Unlike a normal operation switching cycle, however, in a current limit mode switching cycle the high-side MOSFET will turn on as soon as inductor current has fallen to the current limit threshold. 20177444 FIGURE 5. Current Limit Threshold The low-side current sensing scheme can only limit the current during the converter off-time, when inductor current is falling. Therefore in a typical current limit plot the valleys are normally well defined, but the peaks are variable, according to the duty cycle, see Figure 5. The PWM error amplifier and comparator control the pulse of the high-side MOSFET, even during current limit mode, meaning that peak inductor current can exceed the current limit threshold. For example, during an output short-circuit to ground, and assuming that the output inductor does not saturate, the maximum peak inductor current during current limit mode can be calculated with the following equation: LOW-SIDE CURRENT LIMIT The main current limit of the LM3743 is realized by sensing the voltage drop across the low-side FET as the load current passes through it. The RDSON of the MOSFET is a known value; hence the voltage across the MOSFET can be determined as: VDS = IOUT x RDSON The current flowing through the low-side MOSFET while it is on is the falling portion of the inductor current. The current limit threshold is determined by an external resistor, R1, connected between the switching node and the ILIM pin. A constant current (IILIM) of 50 µA typical is forced through R1, causing a fixed voltage drop. This fixed voltage is compared against VDS and if the latter is higher, the current limit of the chip has been reached. To obtain a more accurate value for R1 you must consider the operating values of RDSON and IILIM at their operating temperatures in your application and the effect of slight parameter variations from part to part. R1 can be found by using the following equation using the RDSON value of the low side MOSFET at it's expected hot temperature and the absolute minimum value expected over the full temperature range for the IILIM which is 42.5 µA: Where TSW is the inverse of switching frequency fSW. The 200 ns term represents the minimum off-time of the duty cycle, which ensures enough time for correct operation of the current sensing circuitry. In order to minimize the temperature effects of the peak inductor currents, the IC enters hiccup mode after 15 over current events, or a long current limit event that lasts 15 switching cycles (the counter is reset when 32 non-current limit cycles occur in between two current limit events). Hiccup mode will be discussed in further detail in the “Hiccup Mode and Internal Soft-Start” section. R1 = RDSON-HOT x ICLIM / IILIM www.national.com HIGH-SIDE COARSE CURRENT LIMIT The LM3743 employs a comparator to monitor the voltage across the high-side MOSFET when it is on. This provides 16 LM3743 protection for short circuits from switch node to ground or the case when the inductor is shorted, which the low side current limit cannot detect. A 200 ns blanking time period after the high-side FET turns on is used to prevent switching transient voltages from tripping the high-side current limit without cause. If the difference between VCC pin and SW pin voltage exceeds 500 mV, the LM3743 will immediately enter hiccup mode (see Hiccup Mode section). OUTPUT UNDER-VOLTAGE PROTECTION (UVP) After the end of soft-start the output UVP comparator is activated. The threshold is 50% of the feedback voltage. Once the comparator indicates UVP for more than 7 µs typ. (glitch filter time), the IC goes into hiccup mode. HICCUP MODE AND INTERNAL SOFT-START Hiccup protection mode is designed to protect the external components of the circuit (output inductor, FETs, and input voltage source) from thermal stress. During hiccup mode, the LM3743 disables both the high-side and low-side FETs and begins a cool down period of 5.5 ms. At the conclusion of this cool down period, the regulator performs an internal 3.6 ms soft-start. There are three distinct conditions under which the IC will enter the hiccup protection mode: 1. The low-side current sensing threshold has exceeded the current limit threshold for fifteen sampled cycles, see Figure 6. Each cycle is sampled at the start of each off time (tOFF). The low-side current limit counter is reset when 32 consecutive non-current limit cycles occur in between two current limit events. 2. The high-side current limit comparator has sensed a differential voltage larger than 500 mV. 3. The voltage at the FB pin has fallen below 0.4V, and the UVP comparator has sensed this condition for 7 μs (during steady state operation). The band gap reference, the external soft-start, and internal hiccup soft-start of 3.6 ms (typ) connect to the non-inverting input of the error amplifier through a multiplexer. The lowest voltage of the three connects directly to the non-inverting input. Hiccup mode will not discharge the external soft-start, only UVLO or shut-down will. When in hiccup mode the internal 5.5 ms timer is set, and the internal soft-start capacitor is discharged. After the 5.5 ms timeout, the internal 3.6 ms softstart begins, see Figure 7. During soft-start, only low-side current limit and high side current limit can put the LM3743 into hiccup mode. 20177406 FIGURE 7. Hiccup Time-Out and Internal Soft-Start For example, if the low-side current limit is 10A, then once in overload the low-side current limit controls the valley current and only allows an average amount of 10A plus the ripple current to pass through the inductor and FETs for 15 switching cycles. In such an amount of time, the temperature rise is very small. Once in hiccup mode, the average current through the high-side FET is: IHSF-AVE = (ICLIM + ΔI) x [ D(15 cycles x TSW) ] / 5.5 ms equals 71 mA. With an arbitrary D = 60%, ripple current of 3A, and a 300 kHz switching frequency. The average current through the low-side FET is: ILSF-AVE = (ICLIM + ΔI) x [ (1–D) x (15 cycles x TSW) ] / 5.5 ms equals 47 mA, And the average current through the inductor is: IL-AVE = (ICLIM + ΔI) x [ (15 cycles x TSW) ] / 5.5 ms equals 118 mA. DESIGN CONSIDERATIONS The following is a design procedure for selecting all the components in the Typical Application circuit on the front page. This design converts 5V (VIN) to 1.8V (VOUT) at a maximum load of 10A with an efficiency of 90% and a switching frequency of 300 kHz. The same procedures can be followed to create many other designs with varying input voltages, output voltages, load currents, and switching frequency. Switching Frequency Selection of the operating switching frequency is based on trade-offs between size, cost, efficiency, and response time. For example, a lower frequency will require larger more expensive inductors and capacitors. While a higher switching frequency will generally reduce the size of these components, but will have a reduction in efficiency. Fast switching converters allow for higher loop gain bandwidths, which in turn have the ability to respond quickly to load and line transients. For the example application we have chosen a 300 kHz switching frequency because it will reduce the switching power losses and in turn allow for higher conduction losses considering the same power loss criteria, thus it is possible to sustain a higher load current. Output Inductor The output inductor is responsible for smoothing the square wave created by the switching action and for controlling the output current ripple (ΔIOUT) also called the AC component of the inductor current. The DC current into the load is equal to the average current flowing in the inductor. The inductance is 20177452 FIGURE 6. Entering Hiccup Mode 17 www.national.com LM3743 number and type of capacitors used depends mainly on their size and cost. One exception to this is multi-layer ceramic capacitors. MLCCs have very low ESR, but also low capacitance in comparison with other types. This makes them attractive for lower power designs. For higher power or for fast load transients the number of MLCCs needed often increases the size and cost to unacceptable levels. Because the load could transition quickly from 0 to 10A, more bulk capacitance is needed than the MLCCs can provide. One compromise is a solid electrolytic POSCAP from Sanyo or SP-caps from Panasonic. POSCAP and SPcaps often have large capacitances needed to supply currents for load transients, and low ESRs. The 6TPD470M by Sanyo has 470 µF, and a maximum ESR of 10 mΩ. Solid electrolytics have stable ESR relative to temperature, and capacitance change is relatively immune to bias voltage. Tantalums (Ta), niobium (Nb), and Al-E are good solutions for ambient operating temperatures above 0° C, however their ESR tends to increase quickly below 0°C ambient operating temperature, so these capacitor types are not recommended for this area of operation. chosen by selecting between trade-offs in efficiency, size, and response time. The recommended percentage of AC component to DC current is 30% to 40%, this will provide the best trade-off between energy requirements and size, (read AN-1197 for theoretical analysis). Another criteria is the ability to respond to large load transient responses; the smaller the output inductor, the more quickly the converter can respond. The equation for output inductor selection is: Here we have plugged in the values for input voltage, output voltage, switching frequency, and 30% of the maximum load current. This yields an inductance of 1.34 µH. The output inductor must be rated to handle the peak current (also equal to the peak switch current), which is (IOUT + (0.5 x ΔIOUT)) = 11.5A, for a 10A design and a AC current of 3A. The Coiltronics DR125–1R5 is 1.5 µH, is rated to 13.8A RMS current, and has a direct current resistance (DCR) of 3 mΩ. After selecting the Coiltronics DR125–1R5 for the output inductor, actual inductor current ripple must be re-calculated with the selected inductance value. This information is needed to determine the RMS current through the input and output capacitors. Re-arranging the equation used to select inductance yields the following: Input Capacitor The input capacitors in a buck converter are subjected to high RMS current stress. Input capacitors are selected for their ability to withstand the heat generated by the RMS current and the ESR as specified by the manufacturer. Input RMS ripple current is approximately: Where duty cycle D = VOUT/VIN. The worst-case ripple for a buck converter occurs during full load and when the duty cycle (D) is 0.5. When multiple capacitors of the same type and value are paralleled, the power dissipated by each input capacitor is: VIN(MAX) is assumed to be 10% above the steady state input voltage, or 5.5V at VIN = 5.0V. The re-calculated current ripple will then be 2.69A. This gives a peak inductor/switch current will be 11.35A. where n is the number of paralleled capacitors, and ESR is the equivalent series resistance of each capacitor. The equation above indicates that power loss in each capacitor decreases rapidly as the number of input capacitors increases. For this 5V to 1.8V design the duty cycle is 0.36. For a 10A maximum load the RMS current is 4.8A. Connect one or two 22 µF MLCC as close as possible across the drain of the high-side MOSFET and the source of the lowside MOSFET, this will provide high frequency decoupling and satisfy the RMS stress. A bulk capacitor is recommended in parallel with the MLCC in order to prevent switching frequency noise from reflecting back into the input line, this capacitor should be no more than 1inch away from the MLCC capacitors. Output Capacitor The output capacitor in a switching regulator is selected on the basis of capacitance, equivalent series resistance (ESR), size, and cost. In this example the output current is 10A and the expected type of capacitor is an aluminum electrolytic, as with the input capacitors. An important specification in switching converters is the output voltage ripple ΔVOUT. At 300 kHz the impedance of most capacitors is very small compared to ESR, hence ESR becomes the main selection criteria. In this design the load requires a 2% ripple , which results in a ΔVOUT of 36 mVP-P. Thus the maximum ESR is then: MOSFETs Selection of the power MOSFETs is governed by a trade-off between cost, size, and efficiency. One method is to determine the maximum cost that can be endured, and then select the most efficient device that fits that price. Using a spreadsheet to estimate the losses in the high-side and low-side MOSFETs is one way to determine relative efficiencies between different MOSFETs. Good correlation between the prediction and the bench result is not guaranteed. ESRMAX is 13 mΩ. Aluminum electrolytic (Al-E), tantalum (Ta), solid aluminum, organic, and niobium (Nb) capacitors are all popular in switching converters. In general, by the time enough capacitors have been paralleled to obtain the desired ESR, the bulk capacitance is more than enough to supply the load current during a transient from no-load to full load. The www.national.com 18 maintain low reverse leakage even at high ambient temperature. These diode types have higher forward voltage drop but can still be used for high ambient temperature operation. Control Loop Compensation The LM3743 uses voltage-mode (‘VM’) PWM control to correct changes in output voltage due to line and load transients. VM requires careful small signal compensation of the control loop for achieving high bandwidth and good phase margin. The control loop is comprised of two parts. The first is the power stage, which consists of the duty cycle modulator, output inductor, output capacitor, and load. The second part is the error amplifier, which for the LM3743 is a 30 MHz op-amp used in the classic inverting configuration. Figure 8 shows the regulator and control loop components. PC = D (IOUT2 x RDSON-HI x 1.3) For the low side FET: PC = (1 - D) x (IOUT2 x RDSON-LO x 1.3) In the above equations the factor 1.3 accounts for the increase in MOSFET RDSON due to heating. Alternatively, the 1.3 can be ignored and the RDSON of the MOSFET estimated using the RDSON vs. Temperature curves in the MOSFET manufacturer datasheet. Gate charging loss results from the current driving the gate capacitance of the power MOSFETs, and is approximated as: PGC = (VCC) x QG x fSW VCC is the driving voltage (see MOSFET Gate Driver section) and QG is the gate charge of the MOSFET. If multiple devices will be placed in parallel, their gate charges can simply be summed to form a cumulative QG. Switching loss occurs during the brief transition period as the high-side MOSFET turns on and off, during which both current and voltage are present in the channel of the MOSFET. It can be approximated as: PSW = 0.5 x VIN x IOUT x (tr + tf) x fSW where tr and tf are the rise and fall times of the MOSFET. Switching loss occurs in the high-side MOSFET only. For this example, the maximum drain-to-source voltage applied to either MOSFET is 5.5V. The maximum drive voltage at the gate of the high-side MOSFET is 5.0V, and the maximum drive voltage for the low-side MOSFET is 5.5V. For designs between 5A and 10A, single MOSFETs in SO-8 provide a good trade-off between size, cost, and efficiency. VCC Filtering To ensure smooth DC voltage for the chip supply a 1 µF (C3), X5R MLCC type or better must be placed as close as possible to the VCC and GND pin. Together with a small 1 to 4.99Ω resistor placed between the input rail and the VCC pin, a low pass filter is formed to filter out high frequency noise from injecting into the VCC rail. Since VCC is also the sense pin for the high-side current limit, the resistor should connect close to the drain of the high-side MOSFET to prevent IR drops due to trace resistance. A second design consideration is the low pass filter formed by C3 and R6 on the VCC pin, a fast slew rate, large amplitude load transient may cause a larger voltage droop on CIN than on VCC pin. This may lead to a lower current at which high-side protection may occur. Thus increase the bulk input capacitor if the high-side current limit is engaging due to a dynamic load transient behavior as explained above. 20177413 FIGURE 8. Power Stage and Error Amp One popular method for selecting the compensation components is to create Bode plots of gain and phase for the power stage and error amplifier. Combined, they make the overall bandwidth and phase margin of the regulator easy to see. Software tools such as Excel, MathCAD, and Matlab are useful for showing how changes in compensation or the power stage affect system gain and phase. The power stage modulator provides a DC gain ADC that is equal to the input voltage divided by the peak-to-peak value of the PWM ramp. This ramp is 1.0Vpk-pk for the LM3743. The inductor and output capacitor create a double pole at frequency fDP, and the capacitor ESR and capacitance create a single zero at frequency fESR. For this example, with VIN = 5.0V, these quantities are: Bootstrap Diode (D1) The MBR0520 and BAT54 work well as a bootstrap diode in most designs. Schottky diodes are the preferred choice for the bootstrap circuit because of their low forward voltage drop. For circuits that will operate at high ambient temperature the Schottky diode datasheet must be read carefully to ensure that the reverse current leakage at high temperature does not increase enough to deplete the charge on the bootstrap capacitor while the high side FET is on. Some Schottky diodes increase their reverse leakage by as much as 1000 times at high temperatures. Fast rectifier and PN junction diodes 19 www.national.com LM3743 Losses in the high-side MOSFET can be broken down into conduction loss, gate charging loss, and switching loss. Conduction, or I2R loss, is approximately: For the high side FET: LM3743 bandwidth.) In practice, the loop could easily become unstable due to tolerances in the output inductor, capacitor, or changes in output current, or input voltage. Therefore, the loop is compensated using the error amplifier and a few passive components. For this example, a Type III, or three-pole-two-zero approach gives optimal bandwidth and phase. In most voltage mode compensation schemes, including Type III, a single pole is placed at the origin to boost DC gain as high as possible. Two zeroes fZ1 and fZ2 are placed at the double pole frequency to cancel the double pole phase lag. Then, a pole, fP1 is placed at the frequency of the ESR zero. A final pole fP2 is placed at one-half of the switching frequency. The gain of the error amplifier transfer function is selected to give the best bandwidth possible without violating the Nyquist stability criteria. In practice, a good crossover point is one-fifth of the switching frequency, or 60 kHz for this example. The generic equation for the error amplifier transfer function is: In the equation for fDP, the variable RL is the power stage resistance, and represents the inductor DCR plus the on resistance of the top power MOSFET. RO is the output voltage divided by output current. The power stage transfer function GPS is given by the following equation, and Figure 9 shows Bode plots of the phase and gain in this example. a = LCO(RO + RC) b = L + CO(RORL + RORC + RCRL) c = RO + RL In this equation the variable AEA is a ratio of the values of the capacitance and resistance of the compensation components, arranged as shown in Figure 8. AEA is selected to provide the desired bandwidth. A starting value of 80,000 for AEA should give a conservative bandwidth. Increasing the value will increase the bandwidth, but will also decrease phase margin. Designs with 45-60° are usually best because they represent a good trade-off between bandwidth and phase margin. In general, phase margin is lowest and gain highest (worst-case) for maximum input voltage and minimum output current. One method to select AEA is to use an iterative process beginning with these worst-case conditions. 1. Increase AEA 2. Check overall bandwidth and phase margin 3. Change VIN to minimum and recheck overall bandwidth and phase margin 4. Change IO to maximum and recheck overall bandwidth and phase margin The process ends when both bandwidth and phase margin are sufficiently high. For this example input voltage can vary from 4.5V to 5.5V and output current can vary from 0 to 10A, and after a few iterations a moderate gain factor of 90 dB is used. The error amplifier of the LM3743 has a unity-gain bandwidth of 30 MHz. In order to model the effect of this limitation, the open-loop gain can be calculated as: 20177418 20177419 FIGURE 9. Power Stage Gain and Phase The new error amplifier transfer function that takes into account unity-gain bandwidth is: The double pole at 6 kHz causes the phase to drop to approximately -140° at around 15 kHz. The ESR zero, at 33.9 kHz, provides a +90° boost that prevents the phase from dropping to -180º. If this loop were left uncompensated, the bandwidth would be approximately 15 kHz and the phase margin 40°. In theory, the loop would be stable, but would suffer from poor DC regulation (due to the low DC gain) and would be slow to respond to load transients (due to the low www.national.com 20 LM3743 The gain and phase of the error amplifier are shown in Figure 10. 20177423 In practice, a good trade off between phase margin and bandwidth can be obtained by selecting the closest ±10% capacitor values above what are suggested for C7 and C8, the closest ±10% capacitor value below the suggestion for C9, and the closest ±1% resistor values below the suggestions for R4, R5. Note that if the suggested value for R5 is less than 100Ω, it should be replaced by a short circuit. Following this guideline, the compensation components will be: C7 = 47 pF±10%, C9 = 1.5 nF±10% C8 = 2.2 nF±10%, R4 = 22.6 kΩ±1% R5 = 2.1 kΩ±1% The transfer function of the compensation block can be derived by considering the compensation components as impedance blocks ZF and ZI around an inverting op-amp: 20177424 FIGURE 10. Error Amp. Gain and Phase In VM regulators, the top feedback resistor R2 forms a part of the compensation. Setting R2 to 10 kΩ±1%, usually gives values for the other compensation resistors and capacitors that fall within a reasonable range. (Capacitances > 1 pF, resistances <1 MΩ) C7, C8, C9, R4, and R5 are selected to provide the poles and zeroes at the desired frequencies, using the following equations: As with the generic equation, GEA-ACTUAL must be modified to take into account the limited bandwidth of the error amplifier. The result is: 21 www.national.com LM3743 The total control loop transfer function H is equal to the power stage transfer function multiplied by the error amplifier transfer function. FET Switching Loss (PSW) PSW = PSW(ON) + PSW(OFF) PSW = 0.5 x VIN x IOUT x (tr + tf) x fSW H = GPS x HEA PSW = 0.5 x 5V x 10A x 300 kHz x 67 ns The bandwidth and phase margin can be read graphically from Bode plots of HEA as shown in Figure 11. PSW = 503 mW The Si4866DY has a typical turn-on rise time tr and turn-off fall time tf of 32 ns and 35 ns, respectively. The switching losses for the upper FET (Q1) is 0.503W. The low side FET (Q2) does not incur switching losses. FET Conduction Loss (PCND) PCND = PCND1 + PCND2 PCND1 = I2OUT x RDS(ON) x k x D PCND2 = I2OUT x RDS(ON) x k x (1-D) RDS(ON) = 4.5 mΩ and the k factor accounts for the increase in RDS(ON) due to heating. k = 1.3 at TJ = 100°C PCND1 = (10A)2 x 4.5 mΩ x 1.3 x 0.36 PCND2 = (10A)2 x 4.5 mΩ x 1.3 x (1 - 0.36) PCND = PCND1 + PCND2 PCND = 211 mW + 374 mW = 585 mW 20177429 FET Gate Charging Loss (PGATE) PGATE_H = n x ( VCC - VD1 ) x QGS x fSW PGATE_L = n x VCC x QGS x fSW PGATES = [ 1 x ( 5.0V - 0.4V ) x 22 nC x 300 kHz ] + [ 1 x ( 5.0V ) x 22 nC x 300 kHz ] PGATES = 29 mW + 33 mW = 62 mW The value n is the total number of FETs used and QGS is the typical gate-source charge value, which is 21 nC. For the Si4866DY the gate charging loss is 62 mW. Thus the total MOSFET losses are: PFET = PSW + PCND + PGATES = 503 mW + 585 mW + 62 mW PFET = 1.15 W There are few additional losses that are taken into account: IC Loss (PIC) 20177450 FIGURE 11. Overall Loop Gain and Phase POP = IQ_VCC x VCC PDR = [[ (n x QGS x fSW) / D] +[ (n x QGS x fSW) / (1–D) ]] x VCC The bandwidth of this example circuit is 59 kHz, with a phase margin of 60°. where POP is the operating loss, PDR is the driver loss, IQVCC is the typical operating VCC current EFFICIENCY CALCULATIONS The following is a sample calculation. A reasonable estimation of the efficiency of a switching buck controller can be obtained by adding together the Output Power (POUT) loss and the Total Power loss (PLOSS): POP= ( 1.3 mA x 5.0V ) PDR= [( 1 x 22 nC x 300 kHz ) / .36 ] + [( 1 x 22 nC x 300 kHz ) / .64 ] x VCC PIC= POP + PDR PIC= 6.5 mW + 137 mW = 143.5 mW Input Capacitor Loss (PCAP) The Output Power (POUT) for the Typical Application Circuit design is (1.8V x 10A) = 18W. The Total Power (PLOSS), with an efficiency calculation to complement the design, is shown below. The majority of the power losses are due to the low side and high side MOSFET’s losses. The losses in any MOSFET are switching (PSW), conduction losses (PCND), and gate charging losses (PGATE) www.national.com where, 22 Good layout techniques include a dedicated ground plane, preferably on an internal layer. Signal level components like the compensation and feedback resistors should be connected to a section of this internal plane, signal ground. The signal ground section of the plane should be connected to the power ground at a single point. The best place to connect the signal ground and power ground is right at the GND pin of the IC. Low Impedance Power Path The power path includes the input capacitors, power FETs, output inductor, and output capacitors. Keep these components on the same side of the PCB and connect them with thick traces or copper planes on the same layer. Vias add resistance and inductance to the power path, and have high impedance connections to internal planes than do top or bottom layers of a PCB. If heavy switching currents must be routed through vias and/or internal planes, use multiple vias in parallel to reduce their resistance and inductance. The power components must be kept close together. The longer the paths that connect them, the more they act as antennas, radiating unwanted EMI. Minimize the Switch Node Copper The plane that connects the power FETs and output inductor together radiates more EMI as it gets larger. Use just enough copper to give low impedance to the switching currents. Kelvin Traces For Sense Lines The drain and the source of the high-side FET should be connected as close as possible to the VCC filter resistor (R6) and the SW pin and each pin should connect with a separate trace. The feedback trace should connect the positive node of the output capacitor and connect to the top feedback resistor (R2). Keep this trace away from the switch node and from the output inductor. If driving the COMP pin low with a signal BJT or MOSFET make sure to keep the signal transistor as close as possible to the pin and keep the trace away from EMI radiating nodes and components. PCAP = 230 mW Output Inductor Loss (PIND) PIND = I2OUT x DCR where DCR is the DC resistance. Therefore, for example PIND = (10A)2 x 3 mΩ PIND = 302 mW Total System Efficiency PLOSS = PFET + PIC + PCAP + PIND PCB LAYOUT CONSIDERATIONS To produce an optimal power solution with the LM3743, good layout and design of the PCB are as important as component selection. The following are several guidelines to aid in creating a good layout. For an extensive PCB layout explanation refer to AN-1229. Separate Power Ground and Signal Ground 23 www.national.com LM3743 Here n is the number of paralleled capacitors, ESR is the equivalent series resistance of each, and PCAP is the dissipation in each. So for example if we use only one input capacitor of 10mΩ. LM3743 Example Circuit 1 LM3743-300, VIN = 5V, VOUT = 1.5V, ILOAD = 20A 201774b2 FIGURE 12. Schematic Designator Function Description Part Number Vendor U1 Controller Buck Controller LM3743MSOP-10 National Semiconductor C1 Input Filter 22µF,10V, X7R, 1210 1206ZD227MAT AVX C2, C11 Input Filter POSCAP, 6V, 470µF 6TPD470M Sanyo C3 Decoupling 1µF, 10V, X7R, 0805 0805ZC105KAT AVX C4 Soft Start Cap 180nF, 25V, 0805 VJ0805Y184KXXA Vishay C5 Output Filter 680µF, 2.5V, 5mΩ 2R5TPD680M5 Sanyo C6 Output Filter 150nF, 25V, 0805 VJ0805Y154KXXA Vishay C7 Comp Cap 22pF, 25V, 0603 VJ0603A220KXAA Vishay C8 Comp Cap 680pF, 25V, 0603 VJ0603A681KXAA Vishay C9 Comp Cap 1.5nF, 25V, 0603 VJ0603Y152KXXA Vishay C10 Bootstrap Cap .47µF, 25V, 0805 VJ0805Y474KXXA Vishay R1 Current Limit Res 1.4k, 0603 CRCW06031401F Vishay R2 Top FB Resistor 24.9k, 0603 CRCW06032492F Vishay R3 Bottom FB Res 28k, 0603 CRCW06032802F Vishay R4 Comp Resistor 49.9k, 0603 CRCW06034992F Vishay R5 Comp Resistor 3.32k, 0603 CRCW06033321F Vishay R6 Vcc Filter Resistor 2 ohm, 0603 CRCW06032R00F Vishay L1 Output Filter 1.2µH, DCR = 2.9mΩ SER2009-122ML Coilcraft D1 Bootstrap Diode 500mA, 20V, VF =.3V MBR0520LT1 Onsemi D2 LSPSD IF=2A,VR=20V,VF =.3V SL22 Vishay Q1 Top FET 3.6mΩ@VGS=4.5V, 24.5nC Si7136DP Vishay Q2 Bottom FET 1.7mΩ@VGS=4.5V, 61nC Si7470DP Vishay R3 = 7.87 kΩ (Vout = 3.3V), 11.5 kΩ (Vout = 2.5V), 19.6 kΩ (Vout = 1.8V), 28 kΩ (Vout = 1.5V), 49.9 kΩ (Vout = 1.2V), 100 kΩ (Vout = 1.0V), open (Vout = 0.8V) www.national.com 24 LM3743 Example Circuit LM3743-300, VIN = 3V to 5V, VOUT = 1.5V, ILOAD = 20A In order to operate the LM3743 from an input voltage as low as 3V, the two components in the table below must replace the components found in the bill of materials above. Common loads requiring 20 A are digital rails for FPGAs, ASICs, and DSPs, and power distribution buses. Designator Function Description Part Number Vendor R1 Current Limit Res 1.5k, 0603 CRCW06031501F Vishay Q1 Top FET 4.5mΩ@VGS=4.5V, 21nC Si7882DP Vishay R3 = 7.87 kΩ (Vout = 3.3V), 11.5 kΩ (Vout = 2.5V), 19.6 kΩ (Vout = 1.8V), 28 kΩ (Vout = 1.5V), 49.9 kΩ (Vout = 1.2V), 100 kΩ (Vout = 1.0V), open (Vout = 0.8V) 25 www.national.com LM3743 Physical Dimensions inches (millimeters) unless otherwise noted MSOP-10 Pin Package NS Package Number MUB10A www.national.com 26 LM3743 Notes 27 www.national.com LM3743 High-Performance Synchronous Buck Controller with Comprehensive Fault Protection Features Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: [email protected] German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: [email protected] National Semiconductor Japan Technical Support Center Email: [email protected]