S-8254A Series www.sii-ic.com BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK Rev.5.0_01 © Seiko Instruments Inc., 2002-2010 The S-8254A series is a protection IC for 3-serial- or 4-serial-cell lithium-ion / lithium polymer rechargeable batteries and includes a high-accuracy voltage detector and delay circuit. The S-8254A series protects both 3-serial or 4-serial cells using the SEL pin for switching. Features (1) High-accuracy voltage detection for each cell • Overcharge detection voltage n (n = 1 to 4) 3.9 V to 4.4 V (50 mV steps) Accuracy ±25 mV Accuracy ±50 mV • Overcharge release voltage n (n = 1 to 4) 3.8 V to 4.4 V*1 • Overdischarge detection voltage n (n = 1 to 4) 2.0 V to 3.0 V (100 mV steps) Accuracy ±80 mV Accuracy ±100 mV • Overdischarge release voltage n (n = 1 to 4) 2.0 V to 3.4 V*2 (2) Three-level overcurrent protection • Overcurrent detection voltage 1 0.05 V to 0.30 V (50 mV steps) Accuracy ±25 mV • Overcurrent detection voltage 2 0.5 V Accuracy ±100 mV Accuracy ±300 mV • Overcurrent detection voltage 3 VVC1 − 1.2 V (3) Delay times for overcharge detection, overdischarge detection and overcurrent detection 1 can be set by external capacitors (delay times for overcurrent detection 2 and 3 are fixed internally). (4) Switchable between a 3-serial cell and 4-serial cell using the SEL pin (5) Charge/discharge operation can be controlled via the control pins. (6) High-withstand voltage device Absolute maximum rating : 26 V (7) Wide operating voltage range 2 V to 24 V (8) Wide operating temperature range −40°C to + 85°C (9) Low current consumption • Operation mode 30 μA max. (+25°C) • Power-down mode 0.1 μA max. (+25°C) *3 (10) Lead-free, Sn100%, halogen-free *1. Overcharge hysteresis voltage n (n = 1 to 4) can be selected as 0 V or from a range of 0.1 V to 0.4 V in 50 mV steps. (Overcharge hysteresis voltage = Overcharge detection voltage − Overcharge release voltage) *2. Overdischarge hysteresis voltage n (n = 1 to 4) can be selected as 0 V or from a range of 0.2 V to 0.7 V in 100 mV steps. (Overdischarge hysteresis voltage = Overdischarge release voltage − Overdischarge detection voltage) *3. Refer to “ Product Name Structure” for details. Applications • Lithium-ion rechargeable battery packs • Lithium polymer rechargeable battery packs Package • 16-Pin TSSOP Seiko Instruments Inc. 1 BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK S-8254A Series Rev.5.0_01 Block Diagram COP DOP, COP, RVMD, RVMS Control Circuit VDD Delay Circuit VC1 Delay Circuit − + Delay Circuit 1 MΩ VMP + − Delay Circuit 900 kΩ VC2 − + + − VC3 DOP − + + − + − VINI VC4 + − − + + − + − CDT 200 nA CCT CTL VSS SEL Remark 1. Diodes in the figure are parasitic diodes. 2. Numerical values are typical values. Figure 1 2 Seiko Instruments Inc. Rev.5.0_01 BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK S-8254A Series Product Name Structure 1. Product Name S-8254A xx FT - TB - x Environmental code U: Lead-free (Sn 100%), halogen-free S: Lead-free, halogen-free G: Lead-free (for details, please contact our sales office) IC direction in tape specifications *1 Package code FT: 16-Pin TSSOP Serial code *2 Sequentially set from AA to ZZ *1. Refer to the tape specifications at the end of this book. *2. Refer to “2. Product Name List”. 2. Package Package name 16-Pin TSSOP Environmental code = G, S Environmental code = U Package Tape Reel FT016-A-P-SD FT016-A-P-SD FT016-A-C-SD FT016-A-C-SD FT016-A-R-SD FT016-A-R-S1 Seiko Instruments Inc. 3 BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK S-8254A Series Rev.5.0_01 2. Product Name List Table 1 Product name / Item S-8254AAAFT-TB-x S-8254AABFT-TB-x S-8254AAEFT-TB-x S-8254AAFFT-TB-x S-8254AAGFT-TB-x S-8254AAHFT-TB-x S-8254AAIFT-TB-x S-8254AAJFT-TB-x S-8254AAKFT-TB-x S-8254AALFT-TB-x S-8254AAMFT-TB-x S-8254AANFT-TB-x S-8254AAOFT-TB-X S-8254AAPFT-TB-x S-8254AAQFT-TB-x S-8254AARFT-TB-x S-8254AASFT-TB-x S-8254AATFT-TB-x Overcharge detection voltage [VCU] 4.350 ± 0.025 V 4.250 ± 0.025 V 4.350 ± 0.025 V 4.350 ± 0.025 V 4.275 ± 0.025 V 4.350 ± 0.025 V 4.350 ± 0.025 V 4.350 ± 0.025 V 4.350 ± 0.025 V 4.300 ± 0.025 V 4.200 ± 0.025 V 4.250 ± 0.025 V 4.300 ± 0.025 V 4.280 ± 0.025 V 3.900 ± 0.025 V 4.350 ± 0.025 V 4.290 ± 0.025 V 4.200 ± 0.025 V Overcharge Overdischarge release voltage detection voltage [VCL] [VDL] 4.150 ± 0.050 V 2.00 ± 0.080 V 4.250 ± 0.025 V 2.00 ± 0.080 V 4.150 ± 0.050 V 2.00 ± 0.080 V 4.150 ± 0.050 V 2.40 ± 0.080 V 4.075 ± 0.050 V 2.30 ± 0.080 V 4.150 ± 0.050 V 2.40 ± 0.080 V 4.150 ± 0.050 V 2.40 ± 0.080 V 4.150 ± 0.050 V 2.40 ± 0.080 V 4.150 ± 0.050 V 2.70 ± 0.080 V 4.150 ± 0.050 V 2.40 ± 0.080 V 4.100 ± 0.050 V 2.50 ± 0.080 V 4.150 ± 0.050 V 2.50 ± 0.080 V 4.080 ± 0.050 V 2.50 ± 0.080 V 4.130 ± 0.050 V 3.00 ± 0.080 V 3.800 ± 0.050 V 2.30 ± 0.080 V 4.150 ± 0.050 V 2.80 ± 0.080 V 4.090 ± 0.050 V 2.30 ± 0.080 V 4.200 ± 0.025 V 2.00 ± 0.080 V Overdischarge Overcurrent 0 V battery release voltage detection voltage 1 charge function [VDU] [VIOV1] Available 2.70 ± 0.100 V 0.30 ± 0.025 V Available 2.70 ± 0.100 V 0.30 ± 0.025 V Available 2.70 ± 0.100 V 0.20 ± 0.025 V Available 3.00 ± 0.100 V 0.20 ± 0.025 V Available 2.70 ± 0.100 V 0.13 ± 0.025 V Available 2.70 ± 0.100 V 0.10 ± 0.025 V Available 3.00 ± 0.100 V 0.30 ± 0.025 V Available 3.00 ± 0.100 V 0.15 ± 0.025 V Available 3.00 ± 0.100 V 0.20 ± 0.025 V Available 3.00 ± 0.100 V 0.20 ± 0.025 V Available 2.70 ± 0.100 V 0.30 ± 0.025 V Available 3.00 ± 0.100 V 0.10 ± 0.025 V Available 3.00 ± 0.100 V 0.10 ± 0.025 V Available 3.00 ± 0.080 V 0.15 ± 0.025 V Available 2.70 ± 0.100 V 0.30 ± 0.025 V Available 3.00 ± 0.100 V 0.20 ± 0.025 V Available 3.00 ± 0.100 V 0.075 ± 0.025 V Available 2.70 ± 0.100 V 0.30 ± 0.025 V Unavailable S-8254AAUFT-TB-x 4.350 ± 0.025 V 4.150 ± 0.050 V 2.40 ± 0.080 V 3.00 ± 0.100 V 0.20 ± 0.025 V Available S-8254AAVFT-TB-x 4.250 ± 0.025 V 4.150 ± 0.050 V 2.70 ± 0.080 V 3.00 ± 0.100 V 0.20 ± 0.025 V Unavailable S-8254AAWFT-TB-x 4.250 ± 0.025 V 4.100 ± 0.050 V 3.00 ± 0.080 V 3.20 ± 0.100 V 0.10 ± 0.025 V Available S-8254AAXFT-TB-x 4.250 ± 0.025 V 4.100 ± 0.050 V 2.00 ± 0.080 V 2.70 ± 0.100 V 0.15 ± 0.025 V Available S-8254AAYFT-TB-x 4.275 ± 0.025 V 4.125 ± 0.050 V 2.40 ± 0.080 V 2.70 ± 0.100 V 0.10 ± 0.025 V Available S-8254AAZFT-TB-x 4.250 ± 0.025 V 4.150 ± 0.050 V 2.00 ± 0.080 V 2.70 ± 0.100 V 0.13 ± 0.025 V Available S-8254ABAFT-TB-x 3.900 ± 0.025 V 3.800 ± 0.050 V 2.00 ± 0.080 V 2.50 ± 0.100 V 0.15 ± 0.025 V Available S-8254ABBFT-TB-x 4.200 ± 0.025 V 4.200 ± 0.025 V 2.50 ± 0.080 V 3.20 ± 0.100 V 0.30 ± 0.025 V Available S-8254ABCFT-TB-x 4.175 ± 0.025 V 3.975 ± 0.050 V 2.75 ± 0.080 V 3.05 ± 0.100 V 0.10 ± 0.025 V Available S-8254ABDFT-TB-y 4.300 ± 0.025 V 4.100 ± 0.050 V 2.00 ± 0.080 V 2.00 ± 0.080 V 0.13 ± 0.025 V Available S-8254ABEFT-TB-y 4.200 ± 0.025 V 4.150 ± 0.050 V 2.50 ± 0.080 V 3.00 ± 0.100 V 0.15 ± 0.025 V Available S-8254ABFFT-TB-x 4.150 ± 0.025 V 4.050 ± 0.050 V 2.00 ± 0.080 V 2.70 ± 0.100 V 0.13 ± 0.025 V Available S-8254ABGFT-TB-x 4.180 ± 0.025 V 4.080 ± 0.050 V 2.00 ± 0.080 V 2.70 ± 0.100 V 0.13 ± 0.025 V Available S-8254ABHFT-TB-y 4.150 ± 0.025 V 4.050 ± 0.050 V 2.50 ± 0.080 V 2.80 ± 0.100 V 0.10 ± 0.025 V Unavailable S-8254ABIFT-TB-x 4.215 ± 0.025 V 4.115 ± 0.050 V 2.40 ± 0.080 V 3.00 ± 0.100 V 0.20 ± 0.025 V Remark 1. Please contact our sales office for the products with the detection voltage value other than those specified above. 2. x: G or U y: S or U 3. Please select products of environmental code = U for Sn 100%, halogen-free products. 4 Seiko Instruments Inc. Rev.5.0_01 BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK S-8254A Series Pin Configuration 16-Pin TSSOP Top view COP 1 16 VDD VMP 2 15 VC1 DOP 3 14 VC2 VINI 4 13 VC3 CDT 5 12 VC4 CCT 6 11 CTL VSS 7 10 SEL NC 8 9 NC Figure 2 Table 2 Pin No. 1 Symbol COP Description FET gate connection pin for charge control (Nch open drain output) Pin for voltage detection between VC1 and VMP (Pin for overcurrent 3 2 VMP detection) 3 DOP FET gate connection pin for discharge control FET (CMOS output) Pin for voltage detection between VSS and VINI (Pin for overcurrent detection 4 VINI 1,2) Capacitor connection pin for delay for overdischarge detection, delay for 5 CDT overcurrent detection 1 6 CCT Capacitor connection pin for delay for overcharge current Input pin for negative power supply, 7 VSS Connection pin for battery 4’s negative voltage 8 NC *1 No connection 9 NC *1 No connection Pin for switching 3-series or 4-series cell 10 SEL VSS level: 3-series cell, VDD level : 4-series cell 11 CTL Control of charge FET and discharge FET Connection pin for battery 3’s negative voltage, 12 VC4 Connection pin for battery 4’s positive voltage Connection pin for battery 2’s negative voltage, 13 VC3 Connection pin for battery 3’s positive voltage Connection pin for battery 1’s negative voltage, 14 VC2 Connection pin for battery 2’s positive voltage 15 VC1 Connection pin for battery 1’s positive voltage Input pin for positive power supply, 16 VDD Connection pin for battery 1’s positive voltage *1. The NC pin is electrically open. The NC pin can be connected to VDD or VSS. Seiko Instruments Inc. 5 BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK S-8254A Series Rev.5.0_01 Absolute Maximum Ratings Table 3 Item Symbol Input voltage between VDD and VSS VDS Input pin voltage VIN VMP pin input voltage DOP pin output voltage COP pin output voltage VVMP VDOP VCOP Power dissipation PD Applied pin ⎯ VC1, VC2, VC3, VC4, CTL, SEL, CCT, CDT, VINI VMP DOP COP ⎯ ⎯ ⎯ ⎯ Operating ambient temperature Topr Storage temperature Tstg *1. When mounted on board [Mounted board] (1) Board size : 114.3 mm × 76.2 mm × t1.6 mm (2) Board name : JEDEC STANDARD51-7 (Ta = 25°C unless otherwise specified) Absolute Maximum Ratings Unit V VSS − 0.3 to VSS + 26 VSS − 0.3 to VDD + 0.3 V VSS − 0.3 to VSS + 26 VSS − 0.3 to VDD + 0.3 VSS − 0.3 to VSS + 26 400 (When not mounted on board) 1100*1 − 40 to + 85 − 40 to + 125 V V V mW mW °C °C Caution The absolute maximum ratings are rated values exceeding which the product could suffer physical damage. These values must therefore not be exceeded under any conditions. Power Dissipation (PD) [mW] 1200 1000 800 600 400 200 0 0 50 100 150 Ambient Temperature (Ta) [°C] Figure 3 Power Dissipation of Package (When Mounted on Board) 6 Seiko Instruments Inc. Rev.5.0_01 BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK S-8254A Series Electrical Characteristics Table 4 (1 / 2) Symbol Item [ DETECTION VOLTAGE ] Overcharge detection voltage n (n = 1, 2, 3, 4) Overcharge release voltage n (n = 1, 2, 3, 4) Overdischarge detection voltage n (n = 1, 2, 3, 4) Overdischarge release voltage n (n = 1, 2, 3, 4) VCUn VCLn VDLn VDUn Conditions VCUn − 0.025 VCLn − 0.05 VCLn − 0.025 VDLn − 0.08 VDUn − 0.10 VDUn − 0.08 VIOV1 − 0.025 0.4 VVC1 − 1.5 − 1.0 − 0.5 0.5 VVC1 − 1.2 0 0 VCUn + 0.025 VCLn + 0.05 VCLn + 0.025 VDLn + 0.08 VDUn + 0.10 VDUn + 0.08 VIOV1 + 0.025 0.6 VVC1 − 0.9 1.0 0.5 CCT pin capacitance = 0.1 μF 0.5 1.0 CDT pin capacitance = 0.1 μF 50 CDT pin capacitance = 0.1 μF V 2 V 2 V 2 V 2 V 2 V 2 V 2 V 2 V 2 mV / °C mV / °C 2 2 1.5 s 3 100 150 ms 3 5 10 15 ms 3 ⎯ 0.4 1 1.6 ms 3 FET gate capacitance = 2000 pF 100 300 600 μs 3 0 V battery charging available ⎯ 0.8 1.5 V 4 0 V battery charging unavailable 0.4 0.7 1.1 V 4 ⎯ 0.5 1 1.5 MΩ 5 ⎯ 450 900 1800 kΩ 5 3.9 V to 4.4 V, Adjustable VCL ≠ VCU 3.8 V to 4.4 V, Adjustable VCL = VCU 2.0 V to 3.0 V, Adjustable VDL ≠ VDU 2.0 V to 3.4 V, Adjustable VDL = VDU Overcurrent detection voltage 1 VIOV1 Overcurrent detection voltage 2 VIOV2 ⎯ Overcurrent detection voltage 3 VIOV3 ⎯ *1 Temperature coefficient 1 TCOE1 *2 Temperature coefficient 2 TCOE2 [ DELAY TIME ] Overcharge detection delay time tCU Overdischarge detection tDL delay time Overcurrent detection tIOV1 delay time 1 Overcurrent detection tIOV2 delay time 2 Overcurrent detection tIOV3 delay time 3 [ 0 V BATTERY CHARGE FUNCTION ] 0 V battery charge V0CHA starting charger voltage 0 V battery charge V0INH inhibition battery voltage [ INTERNAL RESISTANCE ] Resistance between RVMD VMP and VDD Resistance between RVMS VMP and VSS (Ta = 25°C unless otherwise specified) Test Min. Typ. Max. Unit circuit 0.05 V to 0.3 V, Adjustable Ta = 0°C to 50°C *3 Ta = 0°C to 50°C *3 Seiko Instruments Inc. VCUn VCLn VCLn VDLn VDUn VDUn VIOV1 7 BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK S-8254A Series Rev.5.0_01 Table 4 (2 / 2) Item [ INPUT VOLTAGE ] Operating voltage between VDD and VSS Symbol VDSOP Conditions Output voltage of DOP and COP fixed (Ta = 25°C unless otherwise specified) Test Min. Typ. Max. Unit circuit 2 ⎯ 24 V 2 CTL input voltage “H” VCTLH ⎯ VDD × 0.8 ⎯ ⎯ V 2 CTL input voltage “L” VCTLL ⎯ ⎯ ⎯ VDD × 0.2 V 2 SEL input voltage “H” VSELH ⎯ VDD × 0.8 ⎯ ⎯ V 2 SEL input voltage “L” VSELL ⎯ ⎯ ⎯ VDD × 0.2 V 2 [ INPUT CURRENT ] Current consumption on operation Current consumption at power down VC1 pin current VC2 pin current VC3 pin current VC4 pin current IOPE V1 = V2 = V3 = V4 = 3.5 V ⎯ 12 30 μA 1 IPDN V1 = V2 = V3 = V4 = 1.5 V ⎯ ⎯ 0.1 μA 1 IVC1 IVC2 IVC3 IVC4 V1 = V2 = V3 = V4 = 3.5 V V1 = V2 = V3 = V4 = 3.5 V V1 = V2 = V3 = V4 = 3.5 V V1 = V2 = V3 = V4 = 3.5 V V1 = V2 = V3 = V4 = 3.5 V, VCTL = VDD V1 = V2 = V3 = V4 = 3.5 V, VCTL = VSS V1 = V2 = V3 = V4 = 3.5 V, VSEL = VDD V1 = V2 = V3 = V4 = 3.5 V, VSEL = VSS ⎯ − 0.3 − 0.3 − 0.3 1.5 0 0 0 3 0.3 0.3 0.3 μA μA μA μA 5 5 5 5 ⎯ ⎯ 0.1 μA 5 − 0.4 − 0.2 ⎯ μA 5 ⎯ ⎯ 0.1 μA 5 − 0.1 ⎯ ⎯ μA 5 CTL pin current “H” ICTLH CTL pin current “L” ICTLL SEL pin current “H” ISELH SEL pin current “L” ISELL [ OUTPUT CURRENT ] 0.1 COP pin leakage current ICOH VCOP = 24 V 5 μA ⎯ ⎯ 10 COP pin sink current ICOL 5 μA VCOP = VSS + 0.5 V ⎯ ⎯ 10 DOP pin source current IDOH VDOP = VDD − 0.5 V 5 μA ⎯ ⎯ 10 DOP pin sink current IDOL 5 μA VDOP = VSS + 0.5 V ⎯ ⎯ *1. Voltage temperature coefficient 1 : Overcharge detection voltage *2. Voltage temperature coefficient 2 : Overcurrent detection voltage 1 *3. Since products are not screened at high and low temperature, the specification for this temperature range is guaranteed by design, not tested in production. 8 Seiko Instruments Inc. Rev.5.0_01 BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK S-8254A Series Test Circuits This chapter describes how to test the S-8254A Series when a 4-serial cell is selected by setting the SEL pin to the VDD level. When a 3-serial cell is selected by setting the SEL pin to the VSS level, short the power supply V4. 1. Current Consumption on Operation, Current Consumption at Power-down (Test circuit 1) 1.1 Current Consumption on Operation (IOPE) The current at the VSS pin when V1 = V2 = V3 = V4 = 3.5 V and VVMP = VDD is the current consumption (IOPE) during operation. 1.2 Current Consumption at Power-down (IPDN) The current at the VSS pin when V1 = V2 = V3 = V4 = 1.5 V and VVMP = VSS is the current consumption (IPDN) at power down. 2. Overcharge Detection Voltage, Overcharge Release Voltage, Overdischarge Detection Voltage, Overdischarge Release Voltage, Overcurrent Detection Voltage 1, Overcurrent Detection Voltage 2, Overcurrent Detection Voltage 3, CTL Input Voltage “H”, CTL Input Voltage “L”, SEL Input Voltage “H”, SEL Input Voltage “L” (Test circuit 2) Confirm that the COP pin and DOP pin are low (VDD × 0.1 V or lower) when VVMP = VSEL = VDD, VINI = VCTL = VSS, the CCT pin is open, the CDT pin is open, and V1 = V2 = V3 = V4 = 3.5 V (this status is referred to as the initial status). 2.1 Overcharge Detection Voltage (VCU1), Overcharge Release Voltage (VCL1) The overcharge detection voltage (VCU1) is the voltage of V1 when the voltage of the COP pin is “H” (VDD × 0.9 V or more) after the V1 voltage has been gradually increased starting at the initial status. The overcharge release voltage (VCL1) is the voltage of V1 when the voltage at the COP pin is “L” after the V1 voltage has been gradually decreased. 2.2 Overdischarge Detection Voltage (VDL1), Overdischarge Release Voltage (VDU1) The overdischarge detection voltage (VDL1) is the voltage of V1 when the voltage of the DOP pin is “H” after the V1 voltage has been gradually decreased starting at the initial status. The overdischarge release voltage (VDU1) is the voltage of V1 when the voltage at the DOP pin is “L” after the V1 voltage has been gradually increased. When the voltage of Vn (n = 2 to 4) is changed, the overcharge detection voltage (VCUn), overcharge release voltage (VCLn), overdischarge detection voltage (VDLn), and overdischarge release voltage (VDUn) can be determined in the same way as when n = 1. 2.3 Overcurrent Detection Voltage 1 (VIOV1) Overcurrent detection voltage 1 (VIOV1) is the voltage of the VINI pin when the voltage of the DOP pin is “H” after the VINI pin voltage has been gradually increased starting at the initial status. 2.4 Overcurrent Detection Voltage 2 (VIOV2) Overcurrent detection voltage 2 (VIOV2) is the voltage of the VINI pin when the voltage of the DOP pin is “H” after the voltage of the CDT pin was set to VSS following the initial status and the voltage of the VINI pin has been gradually decreased. 2.5 Overcurrent Detection Voltage 3 (VIOV3) Overcurrent detection voltage 3 (VIOV3) is the voltage difference between VVC1 and VVMP (VVC1 − VVMP) when the voltage of the DOP pin is “H” after the VMP voltage has been gradually decreased starting at the initial status. Seiko Instruments Inc. 9 BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK S-8254A Series Rev.5.0_01 2.6 CTL Input Voltage “H” (VCTLH), CTL Input Voltage “L” (VCTLL) The CTL input voltage “H” (VCTLH) is the voltage of CTL when the voltages at the COP and DOP pins are “H” after the CTL voltage has been gradually increased starting at the initial status. The CTL input voltage “L” (VCTLL) is the voltage of CTL when the voltages at the COP and DOP pins are “L” after the CTL voltage has been gradually decreased. 2.7 SEL Input Voltage “H” (VSELH), SEL Input Voltage “L” (VSELL) Apply 0 V to V4 in the initial status and confirm that the DOP pin is “H”. The SEL input voltage “L” (VSELL) is the voltage of the SEL pin when the voltage at the DOP pin is “L” after the SEL voltage has been gradually decreased. The SEL input voltage “H” (VSELH) is the voltage of the SEL pin when the voltage of the DOP pin is “H” after the SEL voltage has been gradually increased. 3. Overcharge Detection Delay Time, Overdischarge Detection Delay Time, Overcurrent Detection Delay Time 1, Overcurrent Detection Delay Time 2, Overcurrent Detection Delay Time 3 (Test circuit 3) Confirm that the COP pin and DOP pin are “L” when VVMP = VDD, VINI = VSS, and V1 = V2 = V3 = V4 = 3.5 V (this status is referred to as the initial status). 3.1 Overcharge Detection Delay Time (tCU) The overcharge detection delay time (tCU) is the time it takes for the voltage of the COP pin to change from “L” to “H” after the voltage of V1 is instantaneously changed to 4.5 V from the initial status. 3.2 Overdischarge Detection Delay Time (tDL) The overdischarge detection delay time (tDL) is the time it takes for the voltage of the DOP pin to change from “L” to “H” after the voltage of V1 is instantaneously changed to 1.5 V from the initial status 3.3 Overcurrent Detection Delay Time 1 (tIOV1) Overcurrent detection delay time 1 (tIOV1) is the time it takes for the voltage of the DOP pin to change from “L” to “H” after the voltage of the VINI pin is instantaneously changed to 0.4 V from the initial status. 3.4 Overcurrent Detection Delay Time 2 (tIOV2) Overcurrent detection delay time 2 (tIOV2) is the time it takes for the voltage of the DOP pin to change from “L” to “H” after the voltage of the VINI pin is instantaneously changed to VIOV2 max. + 0.2 V from the initial status. 3.5 Overcurrent Detection Delay Time 3 (tIOV3) Overcurrent detection delay time 3 (tIOV3) is the time it takes for the voltage of the DOP pin to change from “L” to “H” after the voltage of the VMP pin is instantaneously changed to VIOV3 min. − 0.2 V from the initial status. 10 Seiko Instruments Inc. Rev.5.0_01 BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK S-8254A Series 4. 0 V Battery Charge Starting Charger Voltage (Product with 0 V Battery Charge Function), 0 V Battery Charge Inhibition Battery Voltage (Product with 0 V Battery Charge Inhibition Function) (Test circuit 4) Ether the 0 V battery charge starting charger voltage or the 0 V battery charge inhibition battery voltage is applied to each product according to the 0 V battery charging function. 4.1 0 V Battery Charge Starting Battery Charger Voltage (V0CHA) (Product with 0 V Battery Charge Function) The starting condition is V1 = V2 = V3 = V4 = 0 V for a product in which 0 V battery charging is available. The COP pin voltage should be lower than V0CHA max. − 1 V when the VMP pin voltage VVMP = V0CHA max. 4.2 0 V Battery Charge Inhibition Battery Voltage (V0INH) (Product with 0 V Battery Charge Inhibition Function) The starting condition is V1 = V2 = V3 = V4 = V0INH for a product in which 0 V battery charging is inhibited. The COP pin voltage should be higher than VVMP − 1 V when the VMP pin voltage VVMP = 24 V. 5. Resistance between VMP and VDD, Resistance between VMP and VSS, VC1 Pin Current, VC2 Pin Current, VC3 Pin Current, VC4 Pin Current, CTL pin Current “H”, CTL Pin Current “L”, SEL Pin Current “H”, SEL Pin Current “L”, COP Pin Leakage Current, COP Pin Sink Current, DOP Pin Source Current, DOP Pin Sink Current (Test circuit 5) VVMP = VSEL = VDD, VINI = VCTL = VSS, V1 = V2 = V3 = V4 = 3.5 V, and other pins left “open” (this status is referred to as the initial status). 5.1 Resistance between VMP and VDD (RVMD) The resistance between VMP and VDD (RVMD) is obtained from RVMD = VDD / IVMD using the current value of the VMP pin (IVMD) when VVMP is VSS after the initial status. 5.2 Resistance between VMP and VSS (RVMS) The resistance between VMP and VSS (RVMS) is obtained from RVMS = VDD / IVMS using the current value of the VMP pin (IVMS) when V1 = V2 = V3 = V4 = 1.8 V after the initial status. 5.3 VC1 Pin Current (IVC1), VC2 Pin Current (IVC2), VC3 Pin Current (IVC3), VC4 Pin Current (IVC4) At the initial status, the current that flows through the VC1 pin is the VC1 pin current (IVC1), the current that flows through the VC2 pin is the VC2 pin current (IVC2), the current that flows through the VC3 pin is the VC3 pin current (IVC3), and the current that flows through the VC4 pin is the VC4 pin current (IVC4). 5.4 CTL pin Current “H” (ICTLH), CTL Pin Current “L” (ICTLL) In the initial status, the current that flows through the CTL pin is the CTL pin current “L” (ICTLL), after that, when VCTL = VDD, the current that flows through the CTL pin is the CTL pin current “H” (ICTLH). 5.5 SEL Pin Current “H” (ISELH), SEL Pin Current “L” (ISELL) In the initial status, the current that flows through the SEL pin is the SEL pin current “H” (ISELH), after that, when VSEL = VSS, the current that flows through the SEL pin is the SEL pin current “L” (ISELL). Seiko Instruments Inc. 11 BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK S-8254A Series Rev.5.0_01 5.6 COP Pin Leakage Current (ICOH), COP Pin Sink Current (ICOL) The COP pin sink current (ICOL) is the current that flows through the COP pin when VCOP = VSS + 0.5 V after the initial status. After that, the current that flows through the COP pin when V1 = V2 = V3 = V4 = 6 V and VCOP = VDD is the COP pin leakage current (ICOH). 5.7 DOP Pin Source Current (IDOH), DOP Pin Sink Current (IDOL) The DOP pin sink current (IDOL) is the current that flows through the DOP pin when VDOP = VSS + 0.5 V after the initial status. After that, the current that flows through the DOP pin when VVMP = VDD − 2 V and VDOP = VDD − 0.5 V is the DOP pin source current (IDOH). S-8254A A 1 2 3 4 5 6 7 8 COP VMP DOP VINI CDT CCT VSS NC VDD VC1 VC2 VC3 VC4 CTL SEL NC 16 15 14 13 12 11 10 9 V1 V2 V3 V4 C1 = 0.1 μF Figure 4 Test Circuit 1 S-8254A V V 1 2 3 4 5 6 7 8 COP VMP DOP VINI CDT CCT VSS NC VDD VC1 VC2 VC3 VC4 CTL SEL NC 16 15 14 13 12 11 10 9 Figure 5 Test Circuit 2 12 Seiko Instruments Inc. V1 V2 V3 V4 C1 = 0.1 μF BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK S-8254A Series Rev.5.0_01 S-8254A V C2 = 0.1 μF V 1 2 3 4 5 6 7 8 COP VMP DOP VINI CDT CCT VSS NC VDD VC1 VC2 VC3 VC4 CTL SEL NC 16 15 14 13 12 11 10 9 C3 = 0.1 μF V1 V2 V3 V4 C1 = 0.1 μF Figure 6 Test Circuit 3 S-8254A 1 2 3 4 5 6 7 8 V COP VMP DOP VINI CDT CCT VSS NC VDD VC1 VC2 VC3 VC4 CTL SEL NC 16 15 14 13 12 11 10 9 V1 V2 V3 V4 C1 = 0.1 μF Figure 7 Test Circuit 4 S-8254A A A A 1 2 3 4 5 6 7 8 COP VMP DOP VINI CDT CCT VSS NC VDD VC1 VC2 VC3 VC4 CTL SEL NC 16 15 14 13 12 11 10 9 A A A A A A V1 V2 V3 V4 C1 = 0.1 μF Figure 8 Test Circuit 5 Seiko Instruments Inc. 13 BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK S-8254A Series Rev.5.0_01 Operation Remark Refer to “ Battery Protection IC Connection Example”. 1. Normal Status When all of the battery voltages are in the range from VDLn to VCUn and the discharge current is lower than the specified value (the VINI pin voltage is lower than VIOV1 and VIOV2, and the VMP pin voltage is higher than VIOV3), the charging and discharging FETs are turned on. 2. Overcharge Status When any one of the battery voltages becomes higher than VCUn and the state continues for tCU or longer, the COP pin becomes high impedance. The COP pin is pulled up to the EB+ pin voltage by an external resistor, and the charging FET is turned off to stop charging. This is called the overcharge status. The overcharge status is released when one of the following two conditions holds. (1) All battery voltages become VCLn or lower. (2) All of the battery voltages are VCUn or lower, and the VMP pin voltage is 39 / 40 × VDD or lower (a load is connected and discharging is started via the body diode of the charging FET). 3. Overdischarge Status When any one of the battery voltages becomes lower than VDLn and the state continues for tDL or longer, the DOP pin voltage becomes VDD level, and the discharging FET is turned off to stop discharging. This is called the overdischarging status. After discharging is stopped due to the overdischarge status, the S8254A Series enters the power-down status. 4. Power-down Status When discharging has stopped due to the overdischarge status, the VMP pin is pulled down to the VSS level by the RVMS resistor. When the VMP pin voltage is lower than VDD / 2, the S-8254A Series enters the power-down status. In the power-down status, almost all the circuits of the S-8254A Series stop and the current consumption is IPDN or lower. The conditions of each output pin are as follows. (1) COP pin : High-Z (2) DOP pin : VDD The power-down status is released when the following condition holds. (1) The VMP pin voltage is VDD / 2 or higher. The following two conditions release the overdischarging status. (1) In case the VMP pin voltage is VDD / 2 or higher and the VMP pin voltage is lower than VDD, the overdischarging status is released when all battery voltages are VDUn or higher. (2) In case a charger is connected, the overdischarge hysteresis is released. And the overdischarging status is released when all battery voltages are VDLn or higher. 14 Seiko Instruments Inc. Rev.5.0_01 BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK S-8254A Series 5. Overcurrent Status The S-8254A Series has three overcurrent detection levels (VIOV1, VIOV2, and VIOV3) and three overcurrent detection delay times (tIOV1, tIOV2, and tIOV3) corresponding to each overcurrent detection level. When the discharging current becomes higher than the specified value (the voltage between VSS and VINI is greater than VIOV1) and the state continues for tIOV1 or longer, the S-8254A Series enters the overcurrent status, in which the DOP pin voltage becomes VDD level to turn off the discharging FET to stop discharging, the COP pin becomes high impedance and is pulled up to the EB+ pin voltage to turn off the charging FET to stop charging, and the VMP pin is pulled up to the VDD voltage by the internal resistor (RVMD). Operation of overcurrent detection level 2 (VIOV2) and overcurrent detection delay time 2 (tIOV2) is the same as for VIOV1 and tIOV1. In the overcurrent status, the VMP pin is pulled up to the VDD level by the internal resistor in the IC (RVMD resistor). The overcurrent status is released when the following condition holds. (1) The VMP pin voltage is VIOV3 or higher because a charger is connected or the load (30 MΩ or more) is released. 6. 0 V Battery Charge Function Regarding the charging of a self-discharged battery (0 V battery), the S-8254A Series has two functions from which one should be selected. (1) 0 V battery charging is allowed (0 V battery charging is available.) When the charger voltage is higher than V0CHA, the 0 V battery can be charged. (2) 0 V battery charging is prohibited (0 V battery charging is unavailable.) When one of the battery voltages is lower than V0INH, the 0 V battery cannot be charged. Caution When the VDD pin voltage is lower than the minimum value of VDSOP, the operation of the S-8254A Series is not guaranteed. 7. Delay Time Setting The overcharge detection delay time (tCU) is determined by the external capacitor connected to the CCT pin. The overdischarge detection delay time (tDL) and overcurrent detection delay time 1 (tIOV1) are determined by the external capacitor connected to the CDT pin. Overcurrent detection delay times 2 and 3 (tIOV2, tIOV3) are fixed internally. min. typ. max. tCU [s] = (5.00, 10.0, 15.0) × CCCT [μF] tDL [s] = (0.50, 1.00, 1.50) × CCDT [μF] tIOV1 [s] = (0.05, 0.10, 0.15) × CCDT [μF] 8. CTL Pin The S-8254A Series has control pins. The CTL pin is used to control the COP and DOP pin output voltages. CTL pin takes precedence over the battery protection circuit. Table 5 Conditions Set by CTL Pin CTL Pin COP Pin DOP Pin High High-Z VDD Open High-Z VDD *1 Normal status Normal status *1 Low *1. The status is controlled by the voltage detector. Caution Please note unexpected behavior might occur when electrical potential difference between the CTL pin (‘L’ level) and VSS is generated through the external filter (RVSS and CVSS) as a result of input voltage fluctuations. Seiko Instruments Inc. 15 BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK S-8254A Series Rev.5.0_01 9. SEL pin The S-8254A Series has control pins. The SEL pin is used to switch between 3-cell and 4-cell protection. When the SEL pin is low, overdischarge detection of the V4 cell is prohibited and an overdischarge is not detected even if the V4 cell is shorted, therefore, the V4 cell can be used for 3-cell protection. The SEL pin takes precedence over the battery protection circuit. Use the SEL pin at high or low. Table 6 Conditions Set by SEL Pin SEL Pin High Open Low 16 Condition 4-cell protection Undefined 3-cell protection Seiko Instruments Inc. BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK S-8254A Series Rev.5.0_01 Timing Chart 1. Overcharge Detection and Overdischarge Detection VCUn VCLn Battery voltage VDUn VDLn (n = 1 to 4) VDD DOP pin voltage VSS VEB+ COP pin voltage High-Z High-Z VSS VEB+ VDD 39 / 40×VDD VMP pin voltage 1 / 2×VDD VSS Charger connection Load connection Overcharge connection delay time (tCU) Status*1 <1> Overdischarge connection delay time (tDL) <2> <1> <4> <1> <3> *1. < 1 > : Normal status < 2 > : Overcharge status < 3 > : Overdischarge status < 4 > : Power-down status Remark The charger is assumed to charge with a constant current. VEB+ indicates the open voltage of the charger. Figure 9 Seiko Instruments Inc. 17 BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK S-8254A Series Rev.5.0_01 2. Overcurrent detection VHC VCUn VCLn Battery voltage VDUn VDLn VHD (n = 1 to 4) VDD DOP pin voltage VSS VEB+ High-Z COP pin voltage High-Z High-Z VSS VDD VIOV3 VMP pin voltage VSS VDD VINI pin voltage VIOV2 VIOV1 VSS Load connection Status*1 Overcurrent 1 detection delay time (tIOV1) <1> <2> Overcurrent 2 detection Overcurrent 3 detection delay time (tIOV3) delay time (tIOV2) <1> <2> <1> <2> <1> *1. < 1 > : Normal status < 2 > : Overcurrent status Remark The charger is assumed to charge with a constant current. VEB+ indicates the open voltage of the charger. Figure 10 18 Seiko Instruments Inc. BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK S-8254A Series Rev.5.0_01 Battery Protection IC Connection Example 1. 3-serial Cell Charging Discharging FET FET EB+ RVMP RDOP RCOP S-8254A 1 2 3 4 5 6 7 8 RVINI CCDT CCCT COP VMP DOP VINI CDT CCT VSS NC VDD VC1 VC2 VC3 VC4 CTL SEL NC 16 15 14 13 12 11 10 9 CVC1 CVC2 CVC3 RVC1 RVC2 RVC3 RCTL RSEL CTL CVSS RVSS RSENSE EB− Figure 11 2. 4-serial Cell Charging Discharging FET FET EB+ RVMP RDOP RCOP RVINI CCDT CCCT S-8254A 1 2 3 4 5 6 7 8 COP VMP DOP VINI CDT CCT VSS NC VDD VC1 VC2 VC3 VC4 CTL SEL NC 16 15 14 13 12 11 10 9 CVC1 CVC2 CVC3 RVC1 RVC2 RVC3 RVC4 RCTL CVC4 RSEL CTL CVSS RVSS RSENSE EB− Figure 12 Seiko Instruments Inc. 19 BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK S-8254A Series Rev.5.0_01 Table 7 Constants for External Components No. Part Typical Range 1 RVC1 1 0 to 1*1 2 RVC2 1 0 to 1*1 3 RVC3 1 0 to 1*1 4 RVC4 1 0 to 1*1 5 RDOP 5.1 2 to 10 6 RCOP 1 0.1 to 1 7 RVMP 5.1 1 to 10 8 RCTL 1 1 to 100 9 RVINI 1 1 to 100 10 RSEL 1 1 to 100 11 RSENSE 0 or higher ⎯ 12 RVSS 51 10 to 51*1 13 CVC1 0.1 0 to 0.33*1 14 CVC2 0.1 0 to 0.33*1 15 CVC3 0.1 0 to 0.33*1 16 CVC4 0.1 0 to 0.33*1 17 CCCT 0.1 0.01 or higher 18 CCDT 0.1 0.07 or higher 19 CVSS 2.2 2.2 to 10*1 *1. Please set up a filter constant to be RVSS × CVSS ≥ 51 μF • Ω and CVC1 = RVC2 × CVC2 = RVC3 × CVC3 = R VC4 × CVC4 = RVSS × CVSS. Caution Unit kΩ kΩ kΩ kΩ kΩ MΩ kΩ kΩ kΩ kΩ mΩ Ω μF μF μF μF μF μF μF to be RVC1 × 1. The above constants may be changed without notice. 2. It is recommended that filter constants between VDD and VSS should be set approximately to 112 μF • Ω. e.g. CVSS × RVSS = 2.2 μF × 51 Ω = 112 μF • Ω Enough evaluation of transient power supply variation and overcurrent protection function in the actual application is needed to determine the proper constants. Contact our sales office in case the constants should be set to other than 112 μF • Ω or so. 3. It has not been confirmed whether the operation is normal or not in circuits other than the above example of connection. In addition, the example of connection shown above and the constant do not guarantee proper operation. Perform thorough evaluation using the actual application to set the constant. Precautions • The application conditions for the input voltage, output voltage, and load current should not exceed the package power dissipation. • Batteries can be connected in any order, however, there may be cases when discharging cannot be performed when a battery is connected. In this case, short the VMP pin and VDD pin or connect the battery charger to return to the normal mode. • When an overcharged battery and an overdischarged battery intermix, the circuit is in both the overcharge and overdischarge statuses, so charging and discharging are not possible. • Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in electrostatic protection circuit. • SII claims no responsibility for any disputes arising out of or in connection with any infringement by products including this IC of patents owned by a third party. 20 Seiko Instruments Inc. BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK S-8254A Series Rev.5.0_01 Characteristics (Typical Data) 1. Current Consumption 40 35 30 25 20 15 10 5 0 0 1.2 IOPE vs. Ta IOPE [μA] IOPE [μA] 1.1 IOPE vs. VDD 5 10 15 VDD [V] 20 24 0.10 0.09 0.08 0.07 0.06 0.05 0.04 0.03 0.02 0.01 0.00 0 0 25 Ta [°C] 50 75 85 1.4 IPDN vs. Ta IPDN [μA] IPDN [μA] 1.3 IPDN vs. VDD 40 35 30 25 20 15 10 5 0 −40 −25 5 10 15 VDD [V] 20 24 0.10 0.09 0.08 0.07 0.06 0.05 0.04 0.03 0.02 0.01 0.00 −40 −25 0 25 Ta [°C] 50 75 85 2. Overcharge Detection / Release Voltage, Overdischarge Detection / Release Voltage, Overcurrent Detection Voltage, and Delay Times 4.375 4.370 4.365 4.360 4.355 4.350 4.345 4.340 4.335 4.330 4.325 −40 −25 2.2 VCL vs. Ta 4.20 4.18 VCL [V] VCU [V] 2.1 VCU vs. Ta 0 25 Ta [°C] 50 4.10 −40 −25 75 85 0 25 Ta [°C] 50 75 85 0 25 Ta [°C] 50 75 85 2.4 VDL vs. Ta VDL [V] VDU [V] 4.14 4.12 2.3 VDU vs. Ta 2.80 2.78 2.76 2.74 2.72 2.70 2.68 2.66 2.64 2.62 2.60 −40 −25 4.16 0 25 Ta [°C] 50 75 85 Seiko Instruments Inc. 2.08 2.06 2.04 2.02 2.00 1.98 1.96 1.94 1.92 −40 −25 21 BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK S-8254A Series 0.35 0.34 0.33 0.32 0.31 0.30 0.29 0.28 0.27 0.26 0.25 10 2.6 VIOV1 vs. Ta VIOV1 [V] VIOV1 [V] 2.5 VIOV1 vs. VDD 11 12 13 14 VDD [V] 15 16 11 12 13 14 VDD [V] 15 16 −1.0 −1.0 −1.1 −1.1 VIOV3 [V] −0.9 −1.2 −1.3 75 85 0 25 Ta [°C] 50 75 85 0 25 Ta [°C] 50 75 85 −1.2 −1.3 11 12 13 14 VDD [V] 15 −1.5 −40 −25 16 2.12 tCU vs. Ta 1.4 10 1.2 tCU [s] 100 1 1.0 0.8 0.1 0.1 1 CCCT [μF] 22 50 −1.4 2.11 tCU vs. CCCT 0.01 0.01 25 Ta [°C] 2.10 VIOV3 vs. Ta −1.4 tCU [s] 0.60 0.58 0.56 0.54 0.52 0.50 0.48 0.46 0.44 0.42 0.40 −40 −25 −0.9 −1.5 10 0 2.8 VIOV2 vs. Ta 2.9 VIOV3 vs. VDD VIOV3 [V] 0.325 0.320 0.315 0.310 0.305 0.300 0.295 0.290 0.285 0.280 0.275 −40 −25 VIOV2 [V] VIOV2 [V] 2.7 VIOV2 vs. VDD 0.60 0.58 0.56 0.54 0.52 0.50 0.48 0.46 0.44 0.42 0.40 10 Rev.5.0_01 Seiko Instruments Inc. 0.6 −40 −25 0 25 Ta [°C] 50 75 85 BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK S-8254A Series Rev.5.0_01 2.14 tDL vs. Ta 10 200 1 150 tDL [ms] tDL [s] 2.13 tDL vs. CCDT 0.1 0.01 50 0.001 0.01 0.1 CCDT [μF] 1 20 0.1 15 0.01 0.001 25 Ta [°C] 50 75 85 0 25 Ta [°C] 50 75 85 10 5 0.0001 0.01 0.1 CCDT [μF] 0 −40 −25 1 2.17 tIOV2 vs. Ta 2.18 tIOV3 vs. Ta 500 2.0 400 tIOV3 [ms] 1.5 1.0 0.5 0 −40 −25 0 2.16 tIOV1 vs. Ta tIOV1 [ms] tIOV1 [s] 0 −40 −25 1 2.15 tIOV1 vs. CCDT tIOV2 [ms] 100 300 200 100 0 25 Ta [°C] 50 75 85 Seiko Instruments Inc. 0 −40 −25 0 25 Ta [°C] 50 75 85 23 BATTERY PROTECTION IC FOR 3-SERIAL- OR 4-SERIAL-CELL PACK S-8254A Series Rev.5.0_01 3. COP / DOP Pin 3.2 ICOL vs. VCOP 25 0.10 0.09 0.08 0.07 0.06 0.05 0.04 0.03 0.02 0.01 0 20 ICOL [mA] ICOH [μA] 3.1 ICOH vs. VCOP 5 10 15 VCOP [V] 20 3.5 7 VCOP [V] 10.5 14 3.5 7 VDOP [V] 10.5 14 3.4 IDOL vs. VDOP 25 20 IDOL [mA] 0 −0.5 −1.0 −1.5 −2.0 −2.5 −3.0 −3.5 −4.0 −4.5 −5.0 0 0 0 24 3.3 IDOH vs. VDOP IDOH [mA] 10 5 0 24 15 15 10 5 0 1.8 3.6 VDOP [V] 5.4 7.2 Seiko Instruments Inc. 0 5.1±0.2 0.65 16 9 1 8 0.17±0.05 0.22±0.08 No. FT016-A-P-SD-1.1 TITLE TSSOP16-A-PKG Dimensions No. FT016-A-P-SD-1.1 SCALE UNIT mm Seiko Instruments Inc. +0.1 4.0±0.1 ø1.5 -0 0.3±0.05 2.0±0.1 8.0±0.1 1.5±0.1 ø1.6±0.1 (7.2) 4.2±0.2 +0.4 6.5 -0.2 1 16 8 9 Feed direction No. FT016-A-C-SD-1.1 TITLE TSSOP16-A-Carrier Tape FT016-A-C-SD-1.1 No. SCALE UNIT mm Seiko Instruments Inc. 21.4±1.0 17.4±1.0 +2.0 17.4 -1.5 Enlarged drawing in the central part ø21±0.8 2±0.5 ø13±0.2 No. FT016-A-R-SD-2.0 TITLE TSSOP16-A- Reel No. FT016-A-R-SD-2.0 SCALE UNIT QTY. 2,000 mm Seiko Instruments Inc. 21.4±1.0 17.4±1.0 +2.0 17.4 -1.5 Enlarged drawing in the central part ø21±0.8 2±0.5 ø13±0.2 No. FT016-A-R-S1-1.0 TITLE TSSOP16-A- Reel No. FT016-A-R-S1-1.0 SCALE UNIT QTY. 4,000 mm Seiko Instruments Inc. www.sii-ic.com • • • • • • • The information described herein is subject to change without notice. Seiko Instruments Inc. is not responsible for any problems caused by circuits or diagrams described herein whose related industrial properties, patents, or other rights belong to third parties. The application circuit examples explain typical applications of the products, and do not guarantee the success of any specific mass-production design. When the products described herein are regulated products subject to the Wassenaar Arrangement or other agreements, they may not be exported without authorization from the appropriate governmental authority. Use of the information described herein for other purposes and/or reproduction or copying without the express permission of Seiko Instruments Inc. is strictly prohibited. The products described herein cannot be used as part of any device or equipment affecting the human body, such as exercise equipment, medical equipment, security systems, gas equipment, or any apparatus installed in airplanes and other vehicles, without prior written permission of Seiko Instruments Inc. The products described herein are not designed to be radiation-proof. Although Seiko Instruments Inc. exerts the greatest possible effort to ensure high quality and reliability, the failure or malfunction of semiconductor products may occur. The user of these products should therefore give thorough consideration to safety design, including redundancy, fire-prevention measures, and malfunction prevention, to prevent any accidents, fires, or community damage that may ensue.