TRIQUINT TGS2351

TGS2351
DC – 6 GHz High Power SPDT Switch
Applications

High Power Switching
Product Features







Frequency Range: DC – 6 GHz
Power Handling: up to 40 W
Insertion Loss: < 0.8 dB
Isolation: -40 dB typical
Switching Speed: < 15 ns
Control Voltages: 0 V/-40 V from either side of
MMIC
Dimensions: 1.15 x 1.65 x 0.1 mm
General Description
Functional Block Diagram
Vc2
J1
RF In
Vc1
2, 7
4
J2
RF Out1
5
J3
RF Out2
1
3, 6
Bond Pad Configuration
The TriQuint TGS2351 is a Single-Pole, Double-Throw
(SPDT) Switch. The TGS2351 operates from DC to 6
GHz and is designed using TriQuint’s 0.25um GaN on
SiC production process.
Bond Pad #
Symbol
1
2, 7
3, 6
4
5
RF In
Vc2
Vc1
RF Out1
RF Out2
The TGS2351 typically provides up to 40 W input power
handling at control voltages of 0/-40 V. This switch
maintains low insertion loss < 0.8 dB, and high isolation
-40 dB typical.
The TGS2351 is ideally suited for High Power
Switching application.
Lead-free and RoHS compliant
Evaluation Boards are available upon request.
Data Sheet: Rev B
06/20/12
© 2012 TriQuint Semiconductor, Inc.
Ordering Information
Part No.
ECCN
Description
TGS2351
EAR99
DC – 6 GHz High Power
SPDT Switch
- 1 of 11 -
Disclaimer: Subject to change without notice
Connecting the Digital World to the Global Network®
TGS2351
DC – 6 GHz High Power SPDT Switch
Specifications
Absolute Maximum Ratings
Recommended Operating Conditions
Parameter
Rating
Parameter
Control Voltage, Vc
Control Current, Ic
Power Dissipation, Pdiss
RF Input Power, CW, 50Ω,T = 25ºC
RF Input Power, Hot Switching,
50% switching Duty Cycle
Channel Temperature, Tch
Mounting Temperature
(30 Seconds)
Storage Temperature
- 50 V
-1 to 7.8 mA
10 W
47 dBm
Vc1
Vc2
Ic1 / Ic2
40 dBm
275 oC
Min
Typical
-40 / 0
0 / -40
-0.4 to 0.1
Max Units
V
V
mA
Electrical specifications are measured at specified test conditions.
Specifications are not guaranteed over all recommended operating
conditions.
320 oC
-55 to 150 oC
Operation of this device outside the parameter ranges given
above may cause permanent damage. These are stress
ratings only, and functional operation of the device at these
conditions is not implied.
Electrical Specifications
Test conditions unless otherwise noted: 25ºC, Vc1 = -40/0 V, Vc2 = 0/-40 V, see Function Table at Application Circuit on page
6.
Parameter
Min
Operational Frequency Range
Control Current (Ic1/ Ic2)
Insertion Loss (On-State): DC to 6 GHz
Input Return Loss – On-State (Common Port RL)
Output Return Loss – On-State (Switched Port RL)
Isolation (Off-State)
Output Return Loss – Off-Sate (Isolated Port RL)
Input Power 1/
Output Power @ Pin = 46dBm, 1-6GHz
Insertion Loss Temperature Coefficient
Output TOI @ Pin = 23 dBm
Switching Speed – On 2/
Switching Speed – Off 2/
Typical
DC
-1
12
12
44.5
0.5
20
20
-40
2.5
46
45
-0.003
50
15
15
Max
Units
6
0.1
1
GHz
mA
dB
dB
dB
dB
dB
dBm
dBm
dB/°C
dBm
ns
ns
-31
46
1/ The Input Power will be reduced if < 10 MHz.
2/ These Switching Speed dependent on Switch Driver circuit to deliver Vc = 0/-40 V. The rise and fall time of the Switch Driver which
was used to perform for this data is 35 ns, as shown on page 5. For further technical information, see GaN SPDT Switch Drivers
Application Note
Data Sheet: Rev B
06/20/12
© 2012 TriQuint Semiconductor, Inc.
- 2 of 11 -
Disclaimer: Subject to change without notice
Connecting the Digital World to the Global Network®
TGS2351
DC – 6 GHz High Power SPDT Switch
Specifications (cont.)
Thermal and Reliability Information
Parameter
Condition
Rating
Thermal Resistance, θJC, measured to back of carrier (die
mounted to a 20 mil CuMo carrier using 1.5 mil 80/20
AuSn)
Tbase = 70 °C
θJC = 6.1 °C/W
Channel Temperature (Tch), and Median Lifetime (Tm)
Tbase = 70 °C, Vc1 = 0 V, Vc2 = -40
V, Pin = 40 W, Pdiss = 5.3 W
Tch = 102.5 °C
Tm = 7.2 E+9 Hours
Median Lifetime (Tm) vs. Channel Temperature (Tch)
Median Lifetime, Tm (Hours)
1.E+15
1.E+14
1.E+13
1.E+12
1.E+11
1.E+10
1.E+09
1.E+08
1.E+07
1.E+06
1.E+05
FET7
1.E+04
25
50
75
100
125
150
175
200
225
250
275
Channel Temperature, Tch (°C)
Data Sheet: Rev B
06/20/12
© 2012 TriQuint Semiconductor, Inc.
- 3 of 11 -
Disclaimer: Subject to change without notice
Connecting the Digital World to the Global Network®
TGS2351
DC – 6 GHz High Power SPDT Switch
Typical Performance
Insertion Loss (On-State) vs. Frequency
Isolation (Off-State) vs. Frequency
Vc1 = -40 V, Vc2 = 0 V, +25 0C
Vc1 = 0 V, Vc2 = -40 V, +25 0C
-20
-0.2
-30
-0.4
Isolation (dB)
Insertion Loss (dB)
0.0
-0.6
-0.8
-1.0
-1.2
-50
-60
-70
-1.4
-80
-1.6
0
1
2
3
4
5
6
7
8
9
0
10
1
2
4
5
6
7
8
9
10
Frequency (GHz)
Return Loss (On-State) vs. Frequency
Return Loss (Off-State) vs. Frequency
Off-State Output Return Loss (dBm)
0
-5
-10
-15
-20
-25
IRL
-30
ORL
-35
0
1
2
3
4
5
6
7
8
9
10
Vc1 = 0 V, Vc2 = -40 V, +25 0C
0
-1
-2
-3
-4
-5
-6
-7
0
1
2
3
Loss Compression (dB)
-0.1
100 MHz
300 MHz
500 MHz
700 MHz
900 MHz
-0.4
7
8
9
10
0.1
0.0
-0.3
6
Vc1 = -40 V, Vc2 = 0 V, +25 0C
0C
0.1
-0.2
5
Loss Compression vs. Pin vs. Frequency
Loss Compression vs. Pin vs. Frequency
Vc1 = -40 V, Vc2 = 0 V, +25
4
Frequency (GHz)
Frequency (GHz)
Loss Compression (dB)
3
Frequency (GHz)
Vc1 = -40 V, Vc2 = 0 V, +25 0C
On-State Return Loss (dB)
-40
0.0
-0.1
-0.2
1 GHz
2 GHz
3 GHz
4 GHz
-0.3
-0.4
-0.5
-0.5
34
36
Data Sheet: Rev B
38
40
42
Input Power (dBm)
06/20/12
© 2012 TriQuint Semiconductor, Inc.
44
34
46
36
38
40
42
44
46
Input Power (dBm)
- 4 of 11 -
Disclaimer: Subject to change without notice
Connecting the Digital World to the Global Network®
TGS2351
DC – 6 GHz High Power SPDT Switch
Typical Performance (cont.)
Insertion (On-State) vs. Freq vs. Temp
Control Current vs. Pin
Vc1 = -40 V, Vc2 = 0 V, Frequency = 3 GHz, +25 0C
Vc1 = -40 V, Vc2 = 0 V
Insertion Loss (dB)
Control Current, Ic (mA)
0.05
0.04
0.03
0.02
0.01
0.00
34
36
38
40
42
44
0.0
-0.2
-0.4
-0.6
-0.8
-1.0
-1.2
-1.4
-1.6
-1.8
-2.0
46
-55 C
+25 C
+85 C
0
1
Input Power (dBm)
3
4
5
6
7
8
9
10
Frequency (GHz)
Loss Compression vs. Pin vs. Temp
Loss Compression vs. Pin vs. Vc
Vc2 = 0 V, Frequency = 3 GHz, +25 0C
Vc1 = -40 V, Vc2 = 0 V, Frequency = 3 GHz
1
Loss Compression (dB)
0.1
Loss Compression (dB)
2
0.0
-0.1
-0.2
-55 C
+25 V
+85 C
-0.3
-0.4
-0.5
0
-1
-2
Vc1 = -40 V
Vc1 = -30 V
Vc1 = -20 V
-3
-4
-5
34
36
38
40
42
44
46
34
Input Power (dBm)
Switching Speed - On < 50 ns
06/20/12
© 2012 TriQuint Semiconductor, Inc.
38
40
42
44
46
Input Power (dBm)
Switching Speed - Off < 50 ns
Vc = 0/-40 V, Freq = 3 GHz, Pin = 30 dBm, +25 0C
Data Sheet: Rev B
36
Vc = 0/-40 V, Freq = 3 GHz, Pin = 30 dBm, +25 0C
- 5 of 11 -
Disclaimer: Subject to change without notice
Connecting the Digital World to the Global Network®
TGS2351
DC – 6 GHz High Power SPDT Switch
Application Circuit
Vc2
J1
RF In
Vc1
2, 7
4
J2
RF Out1
5
J3
RF Out2
1
3, 6
Vc1 can be biased from either bond pad 3 or 6, and the non-biased bond pad can be left open.
Vc2 can be biased from either bond pad 2 or 7, and the non-biased bond pad can be left open.
This switch can be configured as a Single Pole, Single Throw (SPST) by terminating one unused
RF Out port with a 50 Ohm load.
Bias-up Procedure
Bias-down Procedure
Vc1 or Vc2 set to -40 V (see Function Table below for RF Path)
Vc2 or Vc1 set to 0 V (see Function Table below for RF Path)
Apply RF signal to RF Input
Turn off RF supply
Turn Vc1 to 0V
Turn Vc2 to 0 V
Function Table
RF Path
RF In to RF Out1 (50 Ohm load to RF Out2)
RF In to RF Out2 (50 Ohm load to RF Out1)
Data Sheet: Rev B
06/20/12
© 2012 TriQuint Semiconductor, Inc.
State
Vc1
Vc2
On-State (Insertion Loss)
Off-State (Isolation)
On-State (Insertion Loss)
Off-State (Isolation)
0V
-40 V
-40 V
0V
-40 V
0V
0V
-40 V
- 6 of 11 -
Disclaimer: Subject to change without notice
Connecting the Digital World to the Global Network®
TGS2351
DC – 6 GHz High Power SPDT Switch
Bond Pad Description
2 3
4
1
7 6
5
Bond Pad
Symbol
Description
1
RF In
2, 7
Vc2
3, 6
Vc1
4
5
RF Out1
RF Out2
Input, matched to 50 ohms, DC coupled
Control voltage #2; can be biased from either side (bond pad 2 or bond pad 7), and nonbiased bond pad can be left opened; see Application Circuit on page 6 as an example
Control voltage #1; can be biased from either side (bond pad 3 or bond pad 6), and nonbiased bond pad can be left opened; see Application Circuit on page 6 as an example
Output #1, matched to 50 ohms, DC coupled
Output #2, matched to 50 ohms, DC coupled
Data Sheet: Rev B
06/20/12
© 2012 TriQuint Semiconductor, Inc.
- 7 of 11 -
Disclaimer: Subject to change without notice
Connecting the Digital World to the Global Network®
TGS2351
DC – 6 GHz High Power SPDT Switch
Assembly Drawing
Vc1
RF Out1
RF In
RF Out2
Vc2
Data Sheet: Rev B
06/20/12
© 2012 TriQuint Semiconductor, Inc.
- 8 of 11 -
Disclaimer: Subject to change without notice
Connecting the Digital World to the Global Network®
TGS2351
DC – 6 GHz High Power SPDT Switch
Mechanical Information
0.175 0.300
0.919 0.984
1.652
2 3
1.477
4
1.476
1.276
1.031
1
0.826
0.621
0.377
7 6
0.176
5
0.176
0.0
0.0 0.175 0.300
0.919
1.150
Unit: millimeters
Thickness: 0.10
Die x, y size tolerance: +/- 0.050
Chip edge to bond pad dimensions are shown to center of pad
Ground is backside of die
Bond Pad
1
2, 7
3, 6
4
5
Data Sheet: Rev B
06/20/12
© 2012 TriQuint Semiconductor, Inc.
Symbol
Pad Size
RF In
Vc2
Vc1
RF Out1
RF Out2
0.100 x 0.200
0.100 x 0.100
0.100 x 0.100
0.200 x 0.100
0.200 x 0.100
- 9 of 11 -
Disclaimer: Subject to change without notice
Connecting the Digital World to the Global Network®
TGS2351
DC – 6 GHz High Power SPDT Switch
Product Compliance Information
ESD Information
Solderability
This part is compliant with EU 2002/95/EC RoHS
directive (Restrictions on the Use of Certain Hazardous
Substances in Electrical and Electronic Equipment).
ESD Rating:
Value:
Test:
Standard:
Class 1B
Passes  500 V min.
Human Body Model (HBM)
JEDEC Standard JESD22-A114
ECCN
This product also has the following attributes:
 Lead Free
 Halogen Free (Chlorine, Bromine)
 Antimony Free
 TBBP-A (C15H12Br402) Free
 PFOS Free
 SVHC Free
US Department of Commerce EAR99
Assembly Notes
Component placement and adhesive attachment assembly notes:
• Vacuum pencils and/or vacuum collets are the preferred method of pick up.
• Air bridges must be avoided during placement.
• The force impact is critical during auto placement.
• Organic attachment (i.e. epoxy) can be used in low-power applications.
• Curing should be done in a convection oven; proper exhaust is a safety concern.
Reflow process assembly notes:
• Use AuSn (80/20) solder and limit exposure to temperatures above 300C to 3-4 minutes, maximum.
• An alloy station or conveyor furnace with reducing atmosphere should be used.
• Do not use any kind of flux.
• Coefficient of thermal expansion matching is critical for long-term reliability.
• Devices must be stored in a dry nitrogen atmosphere.
Interconnect process assembly notes:
• Thermosonic ball bonding is the preferred interconnect technique.
• Force, time, and ultrasonics are critical parameters.
• Aluminum wire should not be used.
• Devices with small pad sizes should be bonded with 0.0007-inch wire.
Data Sheet: Rev B
06/20/12
© 2012 TriQuint Semiconductor, Inc.
- 10 of 11 -
Disclaimer: Subject to change without notice
Connecting the Digital World to the Global Network®
TGS2351
DC – 6 GHz High Power SPDT Switch
Contact Information
For the latest specifications, additional product information, worldwide sales and distribution locations, and information about
TriQuint:
Web: www.triquint.com
Email: [email protected]
Tel:
Fax:
+1.972.994.8465
+1.972.994.8504
For technical questions and application information:
Email: [email protected]
Important Notice
The information contained herein is believed to be reliable. TriQuint makes no warranties regarding the information contained
herein. TriQuint assumes no responsibility or liability whatsoever for any of the information contained herein. TriQuint
assumes no responsibility or liability whatsoever for the use of the information contained herein. The information contained
herein is provided "AS IS, WHERE IS" and with all faults, and the entire risk associated with such information is entirely with
the user. All information contained herein is subject to change without notice. Customers should obtain and verify the latest
relevant information before placing orders for TriQuint products. The information contained herein or any use of such
information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property
rights, whether with regard to such information itself or anything described by such information.
TriQuint products are not warranted or authorized for use as critical components in medical, life-saving, or life-sustaining
applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death.
Data Sheet: Rev B
06/20/12
© 2012 TriQuint Semiconductor, Inc.
- 11 of 11 -
Disclaimer: Subject to change without notice
Connecting the Digital World to the Global Network®