NSC DM74LS299WM

DM54LS299/DM74LS299
8-Input Universal Shift/Storage Register
with Common Parallel I/O Pins
General Description
Features
The ’LS299 is an 8-bit universal shift/storage register with
TRI-STATEÉ outputs. Four modes of operation are possible: hold (store), shift left, shift right and load data. The parallel load inputs and flip-flop outputs are multiplexed to reduce the total number of package pins. Separate outputs
are provided for flip-flops Q0 and Q7 to allow easy cascading. A separate active LOW Master Reset is used to reset
the register.
Y
Y
Y
Y
Common I/O for reduced pin count
Four operation modes: shift left, shift right, load and
store
Separate shift right serial input and shift left serial input
for easy cascading
TRI-STATE outputs for bus oriented applications
Connection Diagram
Dual-In-Line Package
TL/F/9827 – 1
Order Number DM54LS299E, DM54LS299J, DM54LS299W,
DM74LS299WM or DM74LS299N
See NS Package Number E20A, J20A, M20B, N20A or W20A
Pin Names
CP
DS0
DS7
S0, S1
MR
OE1, OE2
I/O0–I/O7
Q0–Q7
Description
Clock Pulse Input (Active Rising Edge)
Serial Data Input for Right Shift
Serial Data Input for Left Shift
Mode Select Inputs
Asynchronous Master Reset Input
(Active LOW)
TRI-STATE Output Enable Inputs
(Active LOW)
Parallel Data Inputs or TRI-STATE
Parallel Outputs
Serial Outputs
TRI-STATEÉ is a registered trademark of National Semiconductor Corporation.
C1995 National Semiconductor Corporation
TL/F/9827
RRD-B30M115/Printed in U. S. A.
DM54LS299/DM74LS299 8-Input Universal Shift/Storage Register
with Common Parallel I/O Pins
June 1992
Absolute Maximum Ratings (Note)
Note: The ‘‘Absolute Maximum Ratings’’ are those values
beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The
parametric values defined in the ‘‘Electrical Characteristics’’
table are not guaranteed at the absolute maximum ratings.
The ‘‘Recommended Operating Conditions’’ table will define
the conditions for actual device operation.
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales
Office/Distributors for availability and specifications.
Supply Voltage
7V
Input Voltage
7V
Operating Free Air Temperature Range
b 55§ C to a 125§ C
DM54
DM74LS
0§ C to a 70§ C
Storage Temperature Range
b 65§ C to a 150§ C
Recommended Operating Conditions
Symbol
DM54LS299
Parameter
DM74LS299
Units
Min
Nom
Max
Min
Nom
Max
4.5
5
5.5
4.75
5
5.25
VCC
Supply Voltage
VIH
High Level Input Voltage
VIL
Low Level Input Voltage
IOH
High Level Output Current
IOL
Low Level Output Current
TA
Free Air Operating Temperature
ts(H)
ts(L)
Setup Time HIGH or LOW
S0 or S1 to CP
24
24
24
24
ns
th(H)
th(L)
Hold Time HIGH or LOW
S0 or S1 to CP
5
5
0
0
ns
ts(H)
ts(L)
Setup Time HIGH or LOW
I/On, DS0, DS7 to CP
15
15
10
10
ns
th(H)
th(L)
Hold Time HIGH or LOW
I/On, DS0, DS7 to CP
5
5
0
0
ns
tw(H)
tw(L)
CP Pulse Width HIGH or LOW
15
15
15
15
ns
tw(L)
MR Pulse Width LOW
15
15
ns
trec
Recovery Time
MR to CP
10
10
ns
2
2
V
V
0.7
0.8
V
Q0, Q7
b 0.4
b 0.4
mA
I/O0–I/O7
b 2.6
b 2.6
mA
4
8
mA
24
mA
70
§C
Q0, Q7
I/O0–I/O7
12
b 55
125
0
Electrical Characteristics
Over recommended operating free air temperature range (unless otherwise noted)
Symbol
Parameter
Conditions
VI
Input Clamp Voltage
VCC e Min, II e b18 mA
VOH
High Level Output
Voltage
VCC e Min, IOH e Max
VIL e Max
Min
DM54
Q0, Q7
DM74
I/O0 – I/O7
VOL
II
Low Level Output
Voltage
Input Current @ Max
Input Voltage
Typ
(Note 1)
Max
Units
b 1.5
V
2.5
2.7
3.4
V
2.4
VCC e Min, IOL e Max
VIH e Min
DM54
DM74
0.35
0.5
IOL e 4 mA, VCC e Min
DM74
0.25
0.4
VCC e Max, VI e 10V (DM54)
VI e 7V (DM74)
Inputs
0.1
mA
Sn
0.2
mA
2
0.4
V
Electrical Characteristics (Continued)
Over recommended operating free air temperature range (unless otherwise noted)
Symbol
IIH
Parameter
Conditions
High Level Input Current
IIL
Low Level Input Current
IOS
VCC e Max, VI e 2.7V
VCC e Max, VI e 0.4V
Typ
(Note 1)
Min
Max
Units
Sn
40
mA
Inputs
20
mA
Sn
b 0.8
mA
Inputs
b 0.4
mA
Short Circuit
Output Current
VCC e Max
(Note 2)
Q0, Q7
b 20
b 100
I/O0 – I/O7
b 30
b 130
ICC
Supply Current
VCC e Max, OE e 4.5V
60
mA
IOZH
TRI-STATE Output Off
Current High
VCC e Max
VO e 2.7V
40
mA
IOZL
TRI-STATE Output Off
Current Low
VCC e Max
VO e 0.4V
b 400
mA
Note 1: All typicals are at VCC e 5V, TA e 25§ C.
Note 2: Not more than one output should be shorted at a time, and the duration should not exceed one second.
Switching Characteristics
VCC e a 5.0V, TA e a 25§ C (See Section 1 for waveforms and load configurations)
Symbol
RL e 2 kX
CL e 15 pF
Parameter
Min
Units
Max
fmax
Maximum Input Frequency
35
tPLH
tPHL
Propagation Delay
CP to Q0 or Q7
26
28
MHz
ns
tPLH
tPHL
Propagation Delay
CP to I/On
25
35
ns
tPHL
Propagation Delay
MR to Q0 or Q7
28
ns
tPHL
Propagation Delay
MR to I/On
35
ns
tPZH
tPZL
Output Enable Time
18
25
ns
tPHZ
tPLZ
Output Disable Time
15
20
ns
Logic Symbol
TL/F/9827 – 2
VCC e Pin 20
GND e Pin 10
3
mA
Functional Description
A HIGH signal on either OE1 or OE2 disables the TRISTATE buffers and puts the I/O pins in the high impedance
state. In this condition the shift, hold, load and reset operations can still occur. The TRI-STATE buffers are also disabled by HIGH signals on both S0 and S1 in preparation for
a parallel load operation.
The ’LS299 contains eight edge-triggered D-type flip-flops
and the interstage logic necessary to perform synchronous
shift left, shift right, parallel load and hold operations. The
type of operation is determined by the S0 and S1, as shown
in the Mode Select Table. All flip-flop outputs are brought
out through TRI-STATE buffers to separate I/O pins that
also serve as data inputs in the parallel load mode. Q0 and
Q7 are also brought out on other pins for expansion in serial
shifting of longer words.
A LOW signal on MR overrides the Select and CP inputs
and resets the flip-flops. All other state changes are initiated
by the rising edge of the clock. Inputs can change when the
clock is in either state provided only that the recommended
setup and hold times, relative to the rising edge of CP, are
observed.
Mode Select Table
Inputs
Response
MR S1 S0 CP
L
H
H
H
H
X
H
L
H
L
X
X Asynchronous Reset; Q0 – Q7 e LOW
H L Parallel Load; I/On x Qn
H L Shift Right; DS0 x Q0, Q0 x Q1, etc.
L L Shift Left; DS7 x Q7, Q7 x Q6, etc.
L
X Hold
H e HIGH Voltage Level
L e LOW Voltage Level
X e Immaterial
4
TL/F/9827 – 3
Logic Diagram
5
Physical Dimensions inches (millimeters)
Ceramic Leadless Chip Carrier Package (E)
Order Number DM54LS299E
NS Package Number E20A
20-Lead Ceramic Dual-In-Line Package (J)
Order Number DM54LS299J
NS Package Number J20A
6
Physical Dimensions inches (millimeters) (Continued)
20-Lead Wide Small Outline Molded Package (M)
Order Number DM74LS299WM
NS Package Number M20B
20-Lead Molded Dual-In-Line Package (N)
Order Number DM74LS299N
NS Package Number N20A
7
DM54LS299/DM74LS299 8-Input Universal Shift/Storage Register
with Common Parallel I/O Pins
Physical Dimensions inches (millimeters) (Continued)
20-Lead Ceramic Flat Package (W)
Order Number DM54LS299W
NS Package Number W20A
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL
SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and whose
failure to perform, when properly used in accordance
with instructions for use provided in the labeling, can
be reasonably expected to result in a significant injury
to the user.
National Semiconductor
Corporation
1111 West Bardin Road
Arlington, TX 76017
Tel: 1(800) 272-9959
Fax: 1(800) 737-7018
2. A critical component is any component of a life
support device or system whose failure to perform can
be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or
effectiveness.
National Semiconductor
Europe
Fax: (a49) 0-180-530 85 86
Email: cnjwge @ tevm2.nsc.com
Deutsch Tel: (a49) 0-180-530 85 85
English Tel: (a49) 0-180-532 78 32
Fran3ais Tel: (a49) 0-180-532 93 58
Italiano Tel: (a49) 0-180-534 16 80
National Semiconductor
Hong Kong Ltd.
13th Floor, Straight Block,
Ocean Centre, 5 Canton Rd.
Tsimshatsui, Kowloon
Hong Kong
Tel: (852) 2737-1600
Fax: (852) 2736-9960
National Semiconductor
Japan Ltd.
Tel: 81-043-299-2309
Fax: 81-043-299-2408
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.