AOSMD AON6210

AON6210
30V N-Channel MOSFET
General Description
Product Summary
The AON6210 uses trench MOSFET technology that is
uniquely optimized to provide the most efficient high
frequency switching performance. Conduction and
switching losses are minimized due to an extremely low
combination of RDS(ON) and Crss.In addition,switching
behavior is well controlled with a "Schottky style" soft
recovery body diode.
VDS
RDS(ON) (at VGS=10V)
30V
85A
< 1.8mΩ
RDS(ON) (at VGS = 4.5V)
< 2.5mΩ
ID (at VGS=10V)
100% UIS Tested
100% Rg Tested
DFN5X6
Top View
D
Top View
Bottom View
1
8
2
7
3
6
4
5
G
S
PIN1
Absolute Maximum Ratings TA=25°C unless otherwise noted
Parameter
Symbol
VDS
Drain-Source Voltage
VGS
Gate-Source Voltage
Continuous Drain
Current G
TC=25°C
Pulsed Drain Current
C
Avalanche Current C
Avalanche energy L=0.1mH
C
TC=25°C
Power Dissipation
B
TA=25°C
Power Dissipation A
Junction and Storage Temperature Range
Thermal Characteristics
Parameter
Maximum Junction-to-Ambient A
AD
Maximum Junction-to-Ambient
Maximum Junction-to-Case
Rev0 : Jan 2010
IAS, IAR
85
A
EAS, EAR
361
mJ
83
Steady-State
Steady-State
W
33
2.3
RθJA
RθJC
www.aosmd.com
W
1.5
TJ, TSTG
Symbol
t ≤ 10s
A
22
PDSM
TA=70°C
A
28
PD
TC=100°C
V
350
IDSM
TA=70°C
±20
67
IDM
TA=25°C
Continuous Drain
Current
Units
V
85
ID
TC=100°C
Maximum
30
-55 to 150
Typ
14
40
1
°C
Max
17
55
1.5
Units
°C/W
°C/W
°C/W
Page 1 of 6
AON6210
Electrical Characteristics (TJ=25°C unless otherwise noted)
Parameter
Symbol
STATIC PARAMETERS
BVDSS
Drain-Source Breakdown Voltage
IDSS
Zero Gate Voltage Drain Current
Conditions
Min
ID=250µA, VGS=0V
VDS=30V, VGS=0V
5
IGSS
Gate-Body leakage current
VDS=0V, VGS= ±20V
Gate Threshold Voltage
VDS=VGS ID=250µA
1.1
ID(ON)
On state drain current
VGS=10V, VDS=5V
350
VGS=10V, ID=20A
TJ=125°C
VGS=4.5V, ID=20A
gFS
Forward Transconductance
VSD
Diode Forward Voltage
IS=1A,VGS=0V
Maximum Body-Diode Continuous CurrentG
IS
VDS=5V, ID=20A
DYNAMIC PARAMETERS
Ciss
Input Capacitance
Coss
Output Capacitance
Crss
Reverse Transfer Capacitance
Rg
Gate resistance
SWITCHING PARAMETERS
Qg(10V) Total Gate Charge
Qg(4.5V) Total Gate Charge
Qgs
Gate Source Charge
Qgd
Gate Drain Charge
tD(on)
Turn-On DelayTime
tr
Turn-On Rise Time
tD(off)
Turn-Off DelayTime
tf
Turn-Off Fall Time
trr
Qrr
VGS=0V, VDS=15V, f=1MHz
VGS=0V, VDS=0V, f=1MHz
VGS=10V, VDS=15V, ID=20A
Body Diode Reverse Recovery Time
Body Diode Reverse Recovery Charge IF=20A, dI/dt=500A/µs
µA
100
nA
1.6
2.1
V
1.5
1.8
2.1
2.5
2
2.5
A
110
0.7
mΩ
mΩ
S
1
V
85
A
4200
5250
6300
pF
1500
2240
3000
pF
95
160
270
pF
0.5
1
1.5
Ω
60
80
100
nC
30
38
45
nC
8
10
12
nC
7
13
18
nC
VGS=10V, VDS=15V, RL=0.75Ω,
RGEN=3Ω
IF=20A, dI/dt=500A/µs
Units
V
1
TJ=55°C
Static Drain-Source On-Resistance
Max
30
VGS(th)
RDS(ON)
Typ
12
ns
7
ns
53
ns
14
ns
20
25
30
70
88
105
ns
nC
A. The value of RθJA is measured with the device mounted on 1in 2 FR-4 board with 2oz. Copper, in a still air environment with TA =25°C. The
Power dissipation PDSM is based on R θJA and the maximum allowed junction temperature of 150°C. The value in any given application depends on
the user's specific board design.
B. The power dissipation PD is based on TJ(MAX)=150°C, using junction-to-case thermal resistance, and is more useful in setting the upper
dissipation limit for cases where additional heatsinking is used.
C. Repetitive rating, pulse width limited by junction temperature TJ(MAX)=150°C. Ratings are based on low frequency and duty cycles to keep initial
TJ =25°C.
D. The RθJA is the sum of the thermal impedence from junction to case R θJC and case to ambient.
E. The static characteristics in Figures 1 to 6 are obtained using <300µs pulses, duty cycle 0.5% max.
F. These curves are based on the junction-to-case thermal impedence which is measured with the device mounted to a large heatsink, assuming
a maximum junction temperature of TJ(MAX)=150°C. The SOA curve provides a single pulse rating.
G. The maximum current rating is package limited.
H. These tests are performed with the device mounted on 1 in 2 FR-4 board with 2oz. Copper, in a still air environment with TA=25°C.
THIS PRODUCT HAS BEEN DESIGNED AND QUALIFIED FOR THE CONSUMER MARKET. APPLICATIONS OR USES AS CRITICAL
COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS ARE NOT AUTHORIZED. AOS DOES NOT ASSUME ANY LIABILITY ARISING
OUT OF SUCH APPLICATIONS OR USES OF ITS PRODUCTS. AOS RESERVES THE RIGHT TO IMPROVE PRODUCT DESIGN,
FUNCTIONS AND RELIABILITY WITHOUT NOTICE.
Rev 0 : Jan 2010
www.aosmd.com
Page 2 of 6
AON6210
TYPICAL ELECTRICAL AND THERMAL CHARACTERISTICS
140
140
10V
120
100
3V
80
ID(A)
ID (A)
100
VDS=5V
120
6V
4V
60
80
60
125°C
40
40
20
25°C
20
VGS=2.5V
0
0
0
1
2
3
4
1
5
4
Normalized On-Resistance
RDS(ON) (mΩ)
2
2.5
3
3.5
4
2
3
VGS=4.5V
2
1
VGS=10V
1.8
VGS=10V
ID=20A
1.6
17
5
2
VGS=4.5V10
1.4
1.2
ID=20A
1
0.8
0
0
5
0
10
15
20
25
30
ID (A)
Figure 3: On-Resistance vs. Drain Current and
Gate Voltage (Note E)
25
50
75
100
125
150
175
200
Temperature (°C)
0
Figure 4: On-Resistance vs. Junction Temperature
18
(Note E)
1.0E+02
5
ID=30A
1.0E+01
4
40
1.0E+00
IS (A)
RDS(ON) (mΩ)
1.5
VGS(Volts)
Figure 2: Transfer Characteristics (Note E)
VDS (Volts)
Fig 1: On-Region Characteristics (Note E)
3
125°C
2
125°C
1.0E-01
1.0E-02
25°C
1.0E-03
1
1.0E-04
25°C
1.0E-05
0.0
0
2
4
6
8
10
VGS (Volts)
Figure 5: On-Resistance vs. Gate-Source Voltage
(Note E)
Rev 0: Jan 2010
www.aosmd.com
0.2
0.4
0.6
0.8
1.0
1.2
VSD (Volts)
Figure 6: Body-Diode Characteristics (Note E)
Page 3 of 6
AON6210
TYPICAL ELECTRICAL AND THERMAL CHARACTERISTICS
10
7000
Capacitance (pF)
VGS (Volts)
6
4
2
4000
Coss
3000
2000
Crss
0
0
20
40
60
Qg (nC)
Figure 7: Gate-Charge Characteristics
80
0
10µs
RDS(ON)
limited
10µs
10
15
20
25
VDS (Volts)
Figure 8: Capacitance Characteristics
30
100µs
1ms
10ms
10.0
DC
1.0
TJ(Max)=150°C
TC=25°C
0.1
0.0
0.01
0.1
1
17
5
2
10
120
80
1
VDS (Volts)
10
100
40
0.0001
D=Ton/T
TJ,PK=TC+PDM.ZθJC.RθJC
0.001
0.01
1
0
10
In descending order
D=0.5, 0.3, 0.1, 0.05, 0.02, 0.01, single pulse
40
RθJC=1.5°C/W
PD
0.1
Ton
0.01
0.00001
0.1
Pulse Width (s)
18
Figure 10: Single Pulse Power Rating Junction-toCase (Note F)
Figure 9: Maximum Forward Biased Safe
Operating Area (Note F)
10
TJ(Max)=150°C
TC=25°C
160
Power (W)
100.0
5
200
1000.0
ID (Amps)
5000
1000
0
ZθJC Normalized Transient
Thermal Resistance
Ciss
6000
VDS=15V
ID=20A
8
Single Pulse
0.0001
0.001
0.01
0.1
T
1
10
100
Pulse Width (s)
Figure 11: Normalized Maximum Transient Thermal Impedance (Note F)
Rev 0: Jan 2010
www.aosmd.com
Page 4 of 6
AON6210
TYPICAL ELECTRICAL AND THERMAL CHARACTERISTICS
100
TA=25°C
Power Dissipation (W)
IAR (A) Peak Avalanche Current
1000
TA=100°C
100
TA=150°C
TA=125°C
10
80
60
40
20
0
1
10
100
1000
Time in avalanche, tA (µs)
Figure 12: Single Pulse Avalanche capability (Note
C)
50
75
100
125
150
TCASE (°C)
Figure 13: Power De-rating (Note F)
TA=25°C
80
Power (W)
1000
60
40
17
5
2
10
100
10
20
1
0.00001
0
0
25
50
75
100
125
150
10
1
D=Ton/T
TJ,PK=TA+PDM.ZθJA.RθJA
0.001
0.1
10
0
1000
Pulse Width (s)
18
Figure 15: Single Pulse Power Rating Junction-toAmbient (Note H)
TCASE (°C)
Figure 14: Current De-rating (Note F)
ZθJA Normalized Transient
Thermal Resistance
25
10000
100
Current rating ID(A)
0
In descending order
D=0.5, 0.3, 0.1, 0.05, 0.02, 0.01, single pulse
40
RθJA=55°C/W
0.1
PD
0.01
Single Pulse
Ton
0.001
0.00001
0.0001
0.001
0.01
0.1
1
T
10
100
1000
Pulse Width (s)
Figure 16: Normalized Maximum Transient Thermal Impedance (Note H)
Rev 0: Jan 2010
www.aosmd.com
Page 5 of 6
AON6210
Gate Charge Test Circuit & W aveform
Vgs
Qg
10V
+
+ Vds
VDC
-
VDC
DUT
Qgs
Qgd
-
Vgs
Ig
Charge
Resistive Switching Test Circuit & W aveforms
RL
Vds
Vds
Vgs
90%
+ Vdd
DUT
VDC
Rg
-
10%
Vgs
Vgs
t d(on)
tr
t d(off)
ton
tf
toff
Unclamped Inductive Switching (UIS) Test Circuit & W aveforms
L
2
E AR = 1/2 LIAR
Vds
BVDSS
Vds
Id
+ Vdd
Vgs
Vgs
VDC
Rg
-
I AR
Id
DUT
Vgs
Vgs
Diode Recovery Test Circuit & Waveforms
Q rr = - Idt
Vds +
DUT
Vds -
Isd
Vgs
Ig
Rev 0: Jan 2010
Vgs
Isd
L
+ Vdd
VDC
-
IF
t rr
dI/dt
I RM
Vdd
Vds
www.aosmd.com
Page 6 of 6