HCPL-5300, HCPL-5301, HCPL-530K, 5962-96852 Intelligent Power Module and Gate Drive Interface Hermetically Sealed Optocouplers Data Sheet Description Features The HCPL-530X devices consist of a GaAsP LED optically coupled to an integrated high gain photo detector in a hermetically sealed package. The products are capable of operation and storage over the full military temperature range and can be purchased as either standard product or with full MIL-PRF-38534 Class Level H or K testing or from the DLA Drawing 5962-96852. All devices are manufactured and tested on a MIL-PRF-38534 certified line and are included in the DLA Qualified Manufacturers List QML-38534 for Hybrid Microcircuits. Minimized propagation delay difference between devices make these optocouplers excellent solutions for improving inverter efficiency through reduced switching dead time. An on chip 20 k output pull-up resistor can be enabled by shorting output pins 6 and 7, thus eliminating the need for an external pull-up resistor in common IPM applications. Specifications and performance plots are given for typical IPM applications. Performance specified over full military temperature Range: -55° C to +125° C Minimized pulse width distortion (PWD = 450 ns) High common mode rejection (CMR): 10 kV/s at VCM = 1000 V CTR > 30% at IF = 10 mA 1500 Vdc withstand test voltage Manufactured and tested on a MIL-PRF-38534 certified line Hermetically sealed packages Dual marked with device part number and DLA drawing number QML-38534, Class H and K Schematic Diagram HCPL-4506 function compatibility 8 1 Fast maximum propagation delays tPHL = 450 ns, tPLH = 650 ns Applications Military and space 20 k 2 7 3 6 High reliability systems Harsh industrial environments Transportation, medical, and life critical systems 4 5 SHIELD IPM isolation Isolated IGBT/MOSFET gate drive Truth Table LED VO ON L OFF H AC and brushless DC motor drives Industrial inverters The connection of a 0.1 F bypass capacitor between pins 5 and 8 is recommended. CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. Selection Guide-Lead Configuration Options Avago Part # and Options Commercial HCPL-5300 MIL-PRF-38534, Class H HCPL-5301 MIL-PRF-38534, Class K HCPL-530K Standard Lead Finish Gold Plate Solder Dipped* Option #200 Butt Cut/Gold Plate Option #100 Gull Wing/Soldered* Option #300 Class H SMD Part # Prescript for all below 5962- Gold Plate 9685201HPC Solder Dipped* 9685201HPA Butt Cut/Gold Plate 9685201HYC Butt Cut/Soldered* 9685201HYA Gull Wing/Soldered* 9685201HXA Class K SMD Part # Prescript for all below 5962- Gold Plate 9685201KPC Solder Dipped* 9685201KPA Butt Cut/Gold Plate 9685201KYC Butt Cut/Soldered* 9685201KYA Gull Wing/Soldered* 9685201KXA *Solder contains lead. Outline Drawing 9.40 (0.370) 9.91 (0.390) 0.76 (0.030) 1.27 (0.050) 8.13 (0.320) MAX. 7.16 (0.282) 7.57 (0.298) 4.32 (0.170) MAX. 0.51 (0.020) MIN. 2.29 (0.090) 2.79 (0.110) 3.81 (0.150) MIN. 0.51 (0.020) MAX. NOTE: DIMENSIONS IN MILLIMETERS (INCHES). 2 0.20 (0.008) 0.33 (0.013) 7.36 (0.290) 7.87 (0.310) Device Marking Avago DESIGNATOR Avago P/N DLA SMD* DLA SMD* PIN ONE/ ESD IDENT A QYYWWZ XXXXXX XXXXXXX XXX XXX 50434 COMPLIANCE INDICATOR,* DATE CODE, SUFFIX (IF NEEDED) COUNTRY OF MFR. Avago CAGE CODE* Hermetic Optocoupler Options Option Description 100 Surface mountable hermetic optocoupler with leads trimmed for butt joint assembly. This option is available on commercial and hi-rel product in 8 pin DIP (see drawings below for details). 4.32 (0.170) MAX. 0.51 (0.020) MIN. 2.29 (0.090) 2.79 (0.110) 1.14 (0.045) 1.40 (0.055) 0.20 (0.008) 0.33 (0.013) 0.51 (0.020) MAX. 7.36 (0.290) 7.87 (0.310) NOTE: DIMENSIONS IN MILLIMETERS (INCHES). 200 300 Lead finish is solder dipped rather than gold plated. This option is available on commercial and hi-rel product in 8 pin DIP. DLA Drawing part numbers contain provisions for lead finish. Surface mountable hermetic optocoupler with leads cut and bent for gull wing assembly. This option is available on commercial and hi-rel product in 8 pin DIP (see drawings below for details). This option has solder dipped leads. 4.57 (0.180) MAX. 0.51 (0.020) MIN. 2.29 (0.090) 2.79 (0.110) 1.40 (0.055) 1.65 (0.065) 4.57 (0.180) MAX. 5° MAX. 0.51 (0.020) MAX. NOTE: DIMENSIONS IN MILLIMETERS (INCHES). Note: Solder contains lead. 3 0.20 (0.008) 0.33 (0.013) 9.65 (0.380) 9.91 (0.390) 1.07 (0.042) 1.32 (0.052) Absolute Maximum Ratings Parameter Symbol Min. Storage Temperature TS -65 +150 °C Operating Temperature TA -55 +125 °C Junction Temperature TJ +175 °C 260 for 10 sec °C Average Input Current IF(AVG) 25 mA Peak Input Current (50% duty cycle, ≤ 1 s pulse width) IF(PEAK) 50 mA 1.0 A 5 V Lead Solder Temperature Peak Transient Input Current (≤ 1 s pulse width, 300 pps) Reverse Input Voltage (Pin 3-2) VR Max. Units Average Output Current (Pin 6) IO(AVG) 15 mA Resistor Voltage (Pin 7) V7 -0.5 VCC V Output Voltage (Pin 6-5) VO -0.5 30 V Supply Voltage (Pin 8-5) VCC -0.5 30 V Output Power Dissipation PO 100 mW Total Power Dissipation PT 145 mW ESD Classification (MIL-STD-883, Method 3015) ( ), Class 1 Recommended Operating Conditions Parameter Symbol Min. Max. Units Power Supply Voltage VCC 4.5 30 Volts Output Voltage VO 0 30 Volts Input Current (ON) IF(ON) 10 20 mA Input Voltage (OFF) VF(OFF) -5 0.8 V 4 Electrical Specifications Over recommended operating conditions (TA = -55° C to +125° C, VCC = +4.5 V to 30 V, IF(ON) = 10 mA to 20 mA, VF(OFF) = -5 V to 0.8 V) unless otherwise specified. Parameter Symbol Group A Subgroups[12] Min. Typ.* Current Transfer Ratio CTR 1, 2, 3 30 Low Level Output Current IOL 1, 2, 3 3.0 Low Level Output Voltage VOL 1, 2, 3 0.3 Input Threshold Current ITH 1, 2, 3 High Level Output Current IOH High Level Supply Current Units Test Conditions 90 % IF = 10 mA, VO = 0.6 V 9.0 mA IF = 10 mA, VO = 0.6 V 0.6 V IO = 2.4 mA 1.5 5.0 mA VO = 0.8 V, IO = 0.75 mA 1 1, 2, 3 5 75 A VF = 0.8 V 3 ICCH 1, 2, 3 0.6 1.5 mA VF = 0.8 V, VO = Open 7 Low Level Supply Current ICCL 1, 2, 3 0.6 1.5 mA IF = 10 mA, VO = Open 7 Input Forward Voltage VF 1, 2, 3 1.5 1.8 V IF = 10 mA Temperature Coefficient of Forward Voltage VF/TA mV/°C IF = 10 mA Input Reverse Breakdown Voltage BVR V IR = 100 A Input Capacitance CIN pF f = 1 MHz, VF = 0 V Input-Output Insulation Leakage Current II-O A RH ≤ 65%, t = 5 sec, VI-O = 1500 Vdc, TA = 25° C 2 Resistance (Input-Output) RI-O 1012 VI-O = 500 Vdc 2 Capacitance (Input-Output) CI-O 2.4 pF f = 1 MHz 2 Internal Pull-up Resistor RL k TA = 25° C 4, 5, 6 Internal Pull-up Resistor Temperature Coefficient RL/TA *All typical values at 25° C, VCC = 15 V. 5 1.0 Max. -1.6 1, 2, 3 5 90 1 1 1.0 14 20 0.014 28 k/°C Fig. Note 1 1, 2 7 4 Switching Specifications (RL= 20 k External) Over recommended operating conditions: (TA = -55° C to +125° C, VCC = +4.5 V to 30 V, IF(ON) = 10 mA to 20 mA, VF(OFF) = -5 V to 0.8 V) unless otherwise specified. Parameter Symbol Group A Subgrps.[12] Min. Typ.* Max. Units Test Conditions Propagation Delay Time to Low Output Level tPHL 9, 10, 11 30 180 450 ns CL = 100 pF ns CL = 10 pF Propagation Delay Time to High Output Level tPLH ns CL = 100 pF Pulse Width Distortion PWD Propagation Delay Difference Between Any Two Parts tPLH -tPHL 9, 10, 11 Output High Level Common Mode Immunity Transient |CMH| Output Low Level Common Mode Transient Immunity |CML| 100 250 350 650 CL = 10 pF 130 *All typical values at 25° C, VCC = 15 V. 6 9, 10, 11 9, 10, 11 150 450 ns CL = 100 pF -170 140 500 ns 9 10 17 kV/s IF = 0 mA, VO > 3.0 V 9 10 17 kV/s IF = 10 mA VO < 1.0 V IF(on) = 10 mA, VF(off ) = 0.8 V, VCC = 15.0 V, V THLH = 2.0 V, V THHL = 1.5 V Fig. Note 5, 7, 9-12 3, 4, 5, 6, 7 11 8 VCC = 15.0 V, 6, 17, 9, 13 CL = 100 pF, 18, 21 VCM = 1000 VP-P TA = 25° C 10, 13 Switching Specifications (RL= Internal Pull-up) Over recommended operating conditions: (TA = -55°C to +125°C, VCC = +4.5 V to 30 V, IF(ON) = 10 mA to 20 mA, VF(OFF) = -5 V to 0.8 V) unless otherwise specified. Parameter Symbol Group A Subgrps.[12] Min. Typ.* Max. Units Test Conditions Fig. Note Propagation Delay Time to Low Output Level tPHL 9, 10, 11 20 185 500 ns 5, 8, 3, 4, 5, 6, 7 Propagation Delay Time to High Output Level tPLH 9, 10, 11 220 415 750 ns IF(on) = 10 mA, VF(off ) = 0.8 V, VCC = 15.0 V, CL = 100 pF, V THLH = 2.0 V V THHL = 1.5 V 150 600 ns 11 150 650 ns 8 Pulse Width Distortion PWD 9, 10, 11 Propagation Delay Difference Between Any Two Parts tPLH -tPHL 9, 10, 11 -225 Output High Level Common Mode Transient Immunity |CMH| 10 kV/s IF = 0 mA, VO > 3.0 V Output Low Level Common Mode Transient Immunity |CML| 10 kV/s IF = 16 mA VO < 1.0 V Power Supply Rejection PSR 1.0 VP-P Square Wave, tRISE, tFALL > 5 ns, no bypass capacitors. VCC = 15.0 V, 6, 21 CL = 100 pF, VCM = 1000 VP-P TA = 25° C 9 10 7 *All typical values at 25° C, VCC = 15 V. Notes: 1. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current (IO) to the forward LED input current (IF) times 100. 2. Device considered a two-terminal device: Pins 1, 2, 3 and 4 shorted together and Pins 5, 6, 7 and 8 shorted together. 3. Pulse: f = 20 kHz, Duty Cycle = 10% 4. The internal 20 k resistor can be used by shorting pins 6 and 7 together. 5. Due to the tolerance of the internal resistor, and since propagation delay is dependent on the load resistor value, performance can be improved by using an external 20 k 1% load resistor. For more information on how propagation delay varies with load resistance, see Figure 8. 6. The RL = 20 k, CL = 100 pF represents a typical IPM (Intelligent Power Module) load. 7. Use of a 0.1 F bypass capacitor connected between pins 5 and 8 can improve performance by filtering power supply line noise. 8. The difference in tPLH and tPHL between any two parts under the same test condition. (See IPM Dead Time and Propagation Delay Specifications section.) 9. Common mode transient immunity in a Logic High level is the maximum tolerable dVCM/dt of the common mode pulse, VCM, to assure that the output will remain in a Logic High state (i.e., VO > 3.0 V). 10. Common mode transient immunity in a Logic Low level is the maximum tolerable dVCM/dt of the common mode pulse, VCM, to assure that the output will remain in a Logic Low state (i.e., VO < 1.0 V). 11. Pulse Width Distortion (PWD) is defined as the difference between tPLH and tPHL for any given device. 12. Standard parts receive 100% testing at 25°C (Subgroups 1 and 9). Hi-Rel and SMD parts receive 100% testing at 25° C, +125° C, and -55° C (Subgroups 1 and 9, 2 and 10, 3 and 11 respectively). 13. Parameters are tested as part of device initial characterization and after design and process changes. Parameters are guaranteed to limits specified for all lots not specifically tested. 7 LED Drive Circuit Considerations For Ultra High CMR Performance Without a detector shield, the dominant cause of optocoupler CMR failure is capacitive coupling from the input side of the optocoupler, through the package, to the detector IC as shown in Figure 14. The HCPL-530X improves CMR performance by using a detector IC with an optically transparent Faraday shield, which diverts the capacitively coupled current away from the sensitive IC circuitry. However, this shield does not eliminate the capacitive coupling between the LED and the optocoupler output pins and output ground as shown in Figure 15. This capacitive coupling causes perturbations in the LED current during common mode transients and becomes the major source of CMR failures for a shielded optocoupler. The main design objective of a high CMR LED drive circuit becomes keeping the LED in the proper state (on or off ) during common mode transients. For example, the recommended application circuit (Figure 13), can achieve 10 kV/s CMR while minimizing component complexity. Note that a CMOS gate is recommended in Figure 13 to keep the LED off when the gate is in the high state. Another cause of CMR failure for a shielded optocoupler is direct coupling to the optocoupler output pins through CLEDO1 and CLEDO2 in Figure 15. Many factors influence the effect and magnitude of the direct coupling including: the use of an internal or external output pull-up resistor, the position of the LED current setting resistor, the connection of the unused input package pins, and the value of the capacitor at the optocoupler output (CL). Techniques to keep the LED in the proper state and minimize the effect of the direct coupling are discussed in the next two sections. CMR With The LED On (CMRL) A high CMR LED drive circuit must keep the LED on during common mode transients. This is achieved by overdriving the LED current beyond the input threshold so that it is not pulled below the threshold during a transient. The recommended minimum LED current of 10 mA provides adequate margin over the maximum ITH of 5.0 mA (see Figure 1) to achieve 10 kV/s CMR. Capacitive coupling is higher when the internal load resistor is used (due to CLEDO2) and an IF = 16 mA is required to obtain 10 kV/s CMR. The placement of the LED current setting resistor affects the ability of the drive circuit to keep the LED on during transients and interacts with the direct coupling to the optocoupler output. For example, the LED resistor in Figure 16 is connected to the anode. Figure 17 shows the AC equivalent circuit for Figure 16 during common mode transients. During a +dVCM/dt in Figure 17, the current available at the LED anode (ITOTAL) is limited by the series resistor. The LED current (IF) is reduced from its DC value by an amount equal to the current that flows through CLEDP and CLEDO1. The situation is made worse because the current through CLEDO1 has the effect of trying to pull the output high (toward a CMR failure) at the same time the LED current is being reduced. For this reason, the recommended LED drive circuit (Figure 13) places the current setting resistor in series with the LED cathode. Figure 18 is the AC equivalent circuit for Figure 13 during common mode transients. In this case, the LED current is not reduced during a +dVCM/dt transient because the current flowing through the package capacitance is supplied by the power supply. During a -dVCM/dt transient, however, the LED current is reduced by the amount of current flowing through CLEDN. But better CMR performance is achieved since the current flowing in CLEDO1 during a negative transient acts to keep the output low. Coupling to the LED and output pins is also affected by the connection of pins 1 and 4. If CMR is limited by perturbations in the LED on current, as it is for the recommended drive circuit (Figure 13), pins 1 and 4 should be connected to the input circuit common. However, if CMR performance is limited by direct coupling to the output when the LED is off, pins 1 and 4 should be left unconnected. 8 CMR With The LED Off (CMRH) IPM Dead Time and Propagation Delay Specifications A high CMR LED drive circuit must keep the LED off (VF ≤ VF(OFF)) during common mode transients. For example, during a +dVCM/dt transient in Figure 18, the current flowing through CLEDN is supplied by the parallel combination of the LED and series resistor. As long as the voltage developed across the resistor is less than VF(OFF) the LED will remain off and no common mode failure will occur. Even if the LED momentarily turns on, the 100 pF capacitor from pins 6-5 will keep the output from dipping below the threshold. The recommended LED drive circuit (Figure 13) provides about 10 V of margin between the lowest optocoupler output voltage and a 3 V IPM threshold during a 10 kV/s transient with VCM = 1000 V. Additional margin can be obtained by adding a diode in parallel with the resistor, as shown by the dashed line connection in Figure 18, to clamp the voltage across the LED below VF(OFF). These devices include a Propagation Delay Difference specification intended to help designers minimize “dead time” in their power inverter designs. Dead time is the time period during which both the high and low side power transistors (Q1 and Q2 in Figure 22) are off. Any overlap in Q1 and Q2 conduction will result in large currents flowing through the power devices between the high and low voltage motor rails. Since the open collector drive circuit, shown in Figure 19, cannot keep the LED off during a +dVCM/dt transient, it is not desirable for applications requiring ultra high CMRH performance. Figure 20 is the AC equivalent circuit for Figure 16 during common mode transients. Essentially all the current flowing through CLEDN during a +dVCM/dt transient must be supplied by the LED. CMRH failures can occur at dv/dt rates where the current through the LED and CLEDN exceeds the input threshold. Figure 21 is an alternative drive circuit which does achieve ultra high CMR performance by shunting the LED in the off state. To minimize dead time the designer must consider the propagation delay characteristics of the optocoupler as well as the characteristics of the IPM IGBT gate drive circuit. Considering only the delay characteristics of the optocoupler (the characteristics of the IPM IGBT gate drive circuit can be analyzed in the same way) it is important to know the minimum and maximum turn-on (tPHL) and turn-off (tPLH) propagation delay specifications, preferably over the desired operating temperature range. The limiting case of zero dead time occurs when the input to Q1 turns off at the same time that the input to Q2 turns on. This case determines the minimum delay between LED1 turn-off and LED2 turn-on, which is related to the worst case optocoupler propagation delay waveforms, as shown in Figure 23. A minimum dead time of zero is achieved in Figure 23 when the signal to turn on LED2 is delayed by (tPLH max - tPHL min) from the LED1 turn off. This delay is the maximum value for the propagation delay difference specification which is specified at 500 ns for the HCPL-530X over an operating temperature range of -55° C to +125° C. Delaying the LED signal by the maximum propagation delay difference ensures that the minimum dead time is zero, but it does not tell a designer what the maximum dead time will be. The maximum dead time occurs in the highly unlikely case where one optocoupler with the fastest tPLH and another with the slowest tPHL are in the same inverter leg. The maximum dead time in this case becomes the sum of the spread in the tPLH and tPHL propagation delays as shown in Figure 24. The maximum dead time is also equivalent to the difference between the maximum and minimum propagation delay difference specifications. The maximum dead time (due to the optocouplers) for the HCPL-530X is 670 ns (= 500 ns - (-170 ns)) over an operating temperature range of -55° C to +125° C. 9 1.0 NORMALIZED OUTPUT CURRENT IO – OUTPUT CURRENT – mA 10 8 6 4 VO = 0.6 V 2 0 125°C 25°C -55°C 0 5 10 15 0.9 0.8 0.7 0.6 IF = 10 mA VO = 0.6 V 0.5 0 -60 -40 -20 0 20 40 60 80 100 120 140 20 TA – TEMPERATURE – °C IF – FORWARD LED CURRENT – mA IOH – HIGH LEVEL OUTPUT CURRENT – PA Figure 1. Typical transfer characteristics Figure 2. Normalized output current vs. temperature 1000 25 IF – FORWARD CURRENT – mA VF = 0.8 V VCC = VO = 30 V 20 15 10 5 100 IF + 10 VF – 1.0 0.1 0.01 0.001 1.10 0 -60 -40 -20 0 20 40 60 80 100 120 140 1.20 1.30 1.40 1.50 1.60 VF – FORWARD VOLTAGE – VOLTS TA – TEMPERATURE – °C Figure 3. High level output current vs. temperature Figure 4. Input current vs. forward voltage 8 1 2 20 k: 0.1 μF 20 k: IF(ON) =10 mA + TA = 25°C + – 7 If VCC = 15 V 5V – 3 6 tf VO VOUT tr 90% 90% 10% 10% CL* 4 5 SHIELD *TOTAL LOAD CAPACITANCE Figure 5. Propagation delay test circuit 10 VTHHL VTHLH tPHL tPLH 1 8 0.1 μF 20 k: IF 2 20 k: 7 + – A B 3 6 4 5 VCM VCC = 15 V GV = VCM Gt 't VOUT 100 pF* + OV 't SHIELD VFF *100 pF TOTAL CAPACITANCE – VO VCC SWITCH AT A: IF = 0 mA VO – + VOL SWITCH AT B: IF = 10 mA VCM = 1000 V Figure 6. CMR test circuit. Typical CMR waveform 500 600 IF = 10 mA VCC = 15 V CL = 100 pF RL = 20 k: (EXTERNAL) tP – PROPAGATION DELAY – ns tP – PROPAGATION DELAY – ns 600 400 tPLH tPHL 300 200 100 -60 -40 -20 0 20 40 60 80 100 120 140 IF = 10 mA VCC = 15 V CL = 100 pF RL = 20 k: (INTERNAL) 500 400 tPLH tPHL 300 200 100 -60 -40 -20 0 20 40 60 80 100 120 140 TA – TEMPERATURE – °C TA – TEMPERATURE – °C Figure 7. Propagation delay with external 20 k RL vs. temperature 1400 tP – PROPAGATION DELAY – ns tP – PROPAGATION DELAY – ns 800 1000 400 tPLH tPHL 200 10 20 IF = 10 mA VCC = 15 V RL = 20 k: TA = 25°C 1200 IF = 10 mA VCC = 15 V CL = 100 pF TA = 25 °C 600 0 30 40 50 RL – LOAD RESISTANCE – K: Figure 9. Propagation delay vs. load resistance 11 Figure 8. Propagation delay with internal 20 k RL vs. temperature tPLH tPHL 800 600 400 200 0 0 100 200 300 400 500 CL – LOAD CAPACITANCE – pF Figure 10. Propagation delay vs. load capacitance 500 IF = 10 mA CL = 100 pF RL = 20 k: TA = 25°C tPLH tPHL 1200 1000 tP – PROPAGATION DELAY – ns tP – PROPAGATION DELAY – ns 1400 800 600 400 200 0 5 10 15 20 VCC – SUPPLY VOLTAGE – V 300 200 0 10 5 15 20 Figure 12. Propagation delay vs. input current 8 1 2 7 3 6 20 k: CLEDP + – VCC = 15 V 20 k: 2 7 3 VOUT CMOS 6 CLEDN 100 pF 4 8 1 0.1 μF 20 k: 310 : tPLH tPHL IF – FORWARD LED CURRENT – mA Figure 11. Propagation delay vs. supply voltage +5 V 400 100 30 25 VCC = 15 V CL = 100 pF RL = 20 k: TA = 25°C 5 4 SHIELD 5 SHIELD *100 pF TOTAL CAPACITANCE Figure 13. Recommended LED drive circuit 8 1 2 Figure 14. Optocoupler input to output capacitance model for unshielded optocouplers CLEDP CLED02 2 7 3 6 20 k: + – VCC = 15 V 310 : 6 CLEDN 4 0.1 μF 20 k: 7 CLED01 3 8 1 +5 V 20 k: CMOS 5 SHIELD VOUT 100 pF 4 5 SHIELD *100 pF TOTAL CAPACITANCE Figure 15. Optocoupler input to output capacitance model for shielded optocouplers 12 Figure 16. LED drive circuit with resistor connected to LED anode (not recommended) 8 1 8 1 300 ICLEDP 2 IF CLED02 CLEDP 7 CLED01 CLED02 20 k 7 CLEDN 6 VOUT ICLEDN* + VR** – 100 pF 4 3 VOUT 6 CLEDN CLEDP CLED01 300 ICLED01 3 2 20 k 100 pF 4 5 SHIELD 5 SHIELD * THE ARROWS INDICATE THE DIRECTION OF CURRENT FLOW FOR +dVCM/dt TRANSIENTS. + – + * THE ARROWS INDICATE THE DIRECTION OF CURRENT FLOW FOR +dVCM/dt TRANSIENTS. ** OPTIONAL CLAMPING DIODE FOR IMPROVED CMH PERFORMANCE. VR < VF (OFF) DURING +dVCM/dt. VCM – ITOTAL* 20 k 20 k VCM Figure 17. AC equivalent circuit for Figure 16 during common mode transients Figure 18. AC equivalent circuit for Figure 13 during common mode transients 8 1 2 8 +5 V 20 k 7 3 6 Q1 4 5 SHIELD CLED02 20 k 7 CLED01 Q1 2 CLEDP 3 CLEDN 6 VOUT ICLEDN* 100 pF 4 5 SHIELD * THE ARROWS INDICATE THE DIRECTION OF CURRENT FLOW FOR +dVCM/dt TRANSIENTS. + – 1 20 k VCM Figure 19. Not recommended open collector LED drive circuit 8 1 +5 V 20 k 2 7 3 6 4 5 SHIELD Figure 21. Recommended LED drive circuit for ultra high CMR 13 Figure 20. AC equivalent circuit for Figure 19 during common mode transients HCPL-5300 8 1 20 k I LED1 2 +5 V VCC1 0.1 μF IPM 20 k 7 +HV 310 3 6 4 5 VOUT1 CMOS Q1 M SHIELD Q2 HCPL-5300 8 1 20 k I LED2 2 +5 V VCC2 0.1 μF HCPL-5300 20 k 7 HCPL-5300 310 3 6 4 5 VOUT2 CMOS Figure 22. Typical application circuit ILED1 Q1 OFF VOUT1 VOUT2 HCPL-5300 HCPL-5300 SHIELD Q1 ON Q2 OFF Q2 ON ILED2 tPLH MAX. tPHL MIN. PDD* MAX. = (tPLH-tPHL) MAX. = tPLH MAX. - tPHL MIN. *PDD = PROPAGATION DELAY DIFFERENCE NOTE: THE PROPAGATION DELAYS USED TO CALCULATE PDD ARE TAKEN AT EQUAL TEMPERATURES. Figure 23. Minimum LED skew for zero dead time 14 HCPL-5300 -HV MIL-PRF-38534 Class H, Class K, and DLA SMD Test Program ILED1 Q1 OFF VOUT1 VOUT2 Q1 ON Q2 OFF Q2 ON ILED2 Testing consists of 100% screening and quality conformance inspection to MIL-PRF-38534. tPLH MIN. tPLH MAX. PDD* MAX. Avago Technologies’ Hi-Rel Optocouplers are in compliance with MIL-PRF-38534 Classes H and K. Class H and Class K devices are also in compliance with DLA drawing 5962-96852. tPHL MIN. tPHL MAX. MAX. DEAD TIME MAXIMUM DEAD TIME (DUE TO OPTOCOUPLER) = (tPLH MAX. - tPLH MIN.) + (tPHL MAX. - tPHL MIN.) = (tPLH MAX. - tPHL MIN.) - (tPLH MIN. - tPHL MAX.) = PDD* MAX. - PDD* MIN. *PDD = PROPAGATION DELAY DIFFERENCE NOTE: THE PROPAGATION DELAYS USED TO CALCULATE THE MAXIMUM DEAD TIME ARE TAKEN AT EQUAL TEMPERATURES. Figure 24. Waveforms for dead time calculations For product information and a complete list of distributors, please go to our web site: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright © 2005-2012 Avago Technologies. All rights reserved. Obsoletes 5968-9402EN AV02-3839EN - October 10, 2012