DATASHEET 75V MODULE FEATURES AND BENEFITS TYPICAL APPLICATIONS Ulta-low internal resistance Highest performance available Temperature monitoring Over 1,000,000 duty cycles Grid/Power quality UPS/Backup for heavy machinery Wind turbine pitch systems PRODUCT SPECIFICATIONS ELECTRICAL Rated Capacitance BMOD0094 P075 B02 94 F 1 Minimum Capacitance, initial Maximum ESR DC, initial 94 F 1 13 mΩ 1 Rated Voltage Absolute Maximum Voltage 75 V 91 V 14 Maximum Continuous Current (ΔT = 15 C) o 48 ARMS 2 Maximum Continuous Current (ΔT = 40oC)2 78 ARMS Maximum Peak Current, 1 second (non repetitive) 1,600 A 3 Leakage Current, maximum (B02 Suffix - Passive Balancing) Maximum Series Voltage 4 50 mA 750 V TEMPERATURE Operating Temperature (Ambient temperature) Minimum -40oC Maximum 65oC Storage Temperature (Stored uncharged) Minimum -40oC Maximum 70oC Page 1 Document number: 1012179.6 maxwell.com DATASHEET 75V MODULE PRODUCT SPECIFICATIONS (Cont’d) PHYSICAL BMOD0094 P075 B02 Mass, typical 25 kg Power Terminals M8/M10 Recommended Torque - Terminal 20/30 Nm Vibration Specification SAE J2380 Shock Specification - Environmental Protection IP54 Cooling Natural Convection MONITORING / CELL VOLTAGE MANAGEMENT Internal Temperature Sensor RTD Temperature Interface Analog Cell Voltage Monitoring N/A Connector Harting Cell Voltage Management Passive POWER & ENERGY Usable Specific Power, Pd5 Impedance Match Specific Power, Pmax 2,100 W/kg 4,300 W/kg 6 Specific Energy, Emax7 Stored Energy 2.9 Wh/kg 73.4 Wh 8 LIFE High Temperature1 1,500 hours Capacitance Change 20% ESR Change 100% (at Rated Voltage & Maximum Operating Temperature) (% decrease from minimum initial value) (% increase from maximum initial value) Room Temperature1 15 years Capacitance Change 20% ESR Change 100% (at Rated Voltage & 25oC) (% decrease from minimum initial value) (% increase from maximum initial value) Page 2 Document number: 1012179.6 maxwell.com DATASHEET 75V MODULE PRODUCT SPECIFICATIONS (Cont’d) BMOD0094 P075 B02 Cycle Life1,9 1,000,000 cycles Capacitance Change 20% ESR Change 100% Test Current 100 A (% decrease from minimum initial value) (% increase from maximum initial value) Shelf Life 1,10 2 years (Stored uncharged up to a maximum storage temperature) SAFETY Short Circuit Current, typical 5,800 A (Current possible with short circuit from rated voltage. Do not use as an operating current.) Factory High-Pot Test13 2,500 V DC Certifications RoHS TYPICAL CHARACTERISTICS THERMAL CHARACTERISTICS Thermal Resistance (Rma, Module Case to Ambient), typical N/A Thermal Resistance (Rca, All Cell Cases to Ambient), typical 0.50oC/W Thermal Capacitance (Cth), typical 2 19,200 J/oC ESR AND CAPACITANCE VS TEMPERATURE 180% Capacitance DC ESR Percentage change from value at 25°C 170% 160% 150% 140% 130% 120% 110% 100% 90% 80% -60 -40 -20 0 20 40 60 Temperature (°C) Page 3 Document number: 1012179.6 maxwell.com 80 DATASHEET 75V MODULE NOTES 1. Capacitance and ESRDC measured at 25°C per Document Number 1007239 available at www.maxwell.com. 2. Per Maxwell Document 1007239 available at www.maxwell.com. ½ CV 3. Maximum Peak current (1 sec) = C x ESRDC + 1 4. After 72 hours at 25°C and rated voltage. Initial leakage current can be higher. 0.12V2 5. Per IEC 62391-2, Pd = ESR x mass DC V2 6. Pmax = 4 x ESRDC x mass 7. Emax = ½ CV2 3,600 x mass MOUNTING RECOMMENDATIONS Please refer to the user manual for installation recommendations Page 4 Document number: 1012179.6 maxwell.com 8. Estored = ½ CV2 3,600 9. Cycle per Document Number 1007239 available at www.maxwell.com. 10. No more than 10% decrease in capacitance from minimum initial capacitance or 50% increase in ESR from maximum initial ESR. 11. Tested at 1 kV DC. 12. For a given application, sufficient cooling must be provided to keep cell case temperatures below 65°. See Rth. 13. Duration = 60 seconds. Not intended as an operating parameter. 14. Absolute maximum voltage non repeated, not to exceed 1 second. MARKINGS Products are marked with the following information: Rated capacitance, rated voltage, product number, name of manufacturer, positive and negative terminal, warning marking, serial number. DATASHEET 75V MODULE BMOD0094 P075 4 3 2 1 REVISIONS NEGATIVE TERMINAL REV DESCRIPTION CO 1 PRODUCTION RELEASE - 37.0 D 263 W 126.0 189.0 68.5 C 131.5 POSITIVE TERMINAL 220 H 195 252.0 L 515 183 B Dimensions (mm) NOTICE: W (±0.2mm) DO NOT SCALE DRAWING Part Description A BMOD0094 P075 B02 L (±0.3mm) 515 THE INFORMATION CONTAINED IN THIS DOCUMENT IS MAXWELL CONFIDENTIAL INFORMATION AND IS THE SOLE PROPERTY OF MAXWELL TECHNOLOGIES. ANY REPRODUCTION IN PART OR WHOLE WITHOUT WRITTEN PERMISSION OF MAXWELL TECHNOLOGIES IS PROHIBITED. 263 UNLESS OTHERWISE SPECIFIED, ALL DIMENSIONS ARE IN MILIMETERS AFTER PLATING. DRAWN BREAK EDGES 0.3 LATHE FINISH 63 µINCH, MILL FINISH 125 µINCH CHECKED X.XXX DIAMETERS 0.125 TIR X.XXX DIA SURFACES X .X .XX MATERIAL APPROVALS DATE Package Quantity L. ANDERSON H (±0.7mm) & ±1 ±.25 ±.125 0.025mm ANGLE ±0.5° 220 DESIGN ENGR 4/26/2010 1 MECHANICAL ENGR PROCESS ENGR 1 9244 BALBOA AVENUE, SAN DIEGO, CA 92123 U.S.A DESCRIPTION MODULE ASSY, BMOOD0094 P075 B02 N/A Product dimensions are for reference only unless otherwise identified. Product dimensions and specifications may change without notice. 107725 Please contact Maxwell Technologies directly for any technical specifications critical to application. All products featured on this B 68911 N/A 1 OF 1 DATESHEET 1:5 7027290, 1 1 datasheet are covered by the following U.S. patents and their respective foreign counterparts: 7307830, 7203056, 7.352.558, 7.295.423, 7.090.946, 7.508.651, 7.492.571, 7.342.770, 3 6.643.119, 7.384.433, 7.147.674, 7.317.609, 2 7.495.349, 7.102.877. 1 4 3RD ANGLE PROJECTION TEST ENGR SIZE CAUTION CONTAINS PARTS AND/OR ASSEMBLIES SUSCEPTIBLE TO DAMAGE BY ELECTROSTATIC DISCHARGE (ESD) FINISH CAGE CODE PART NO. QUALITY ENGR PRODUCTION ENGR SCALE DOC. NO. REV SHEET 1 REV A 7/01 Maxwell Technologies, Inc. Global Headquarters 5271 Viewridge Court, Suite 100 San Diego, CA 92123 USA Tel: +1 858 503 3300 Fax: +1 858 503 3301 Page 5 Maxwell Technologies SA CH-1728 Rossens Switzerland Tel: +41 (0)26 411 85 00 Fax: +41 (0)26 411 85 05 Document number: 1012179.6 maxwell.com Maxwell Technologies, GmbH Brucker Strasse 21 D-82205 Gilching Germany Tel: +49 (0)8105 24 16 16 Fax: +49 (0)8105 24 16 19 Maxwell Technologies, Inc. Shanghai Representative Office 13E, CR Times Square 500 Zhangyang Road, Pudong Shanghai 200122, P.R. China Tel: +86 21 5836 8780 Fax: +86 21 5836 8790 REV A