TI TCA6424

TCA6424
www.ti.com
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
2
LOW-VOLTAGE 24-BIT I C AND SMBus I/O EXPANDER
WITH INTERRUPT OUTPUT, RESET, AND CONFIGURATION REGISTERS
Check for Samples: TCA6424
FEATURES
1
•
•
•
•
•
•
•
•
•
Operating Power-Supply Voltage Range of
1.65 V to 5.5 V
Allows Bidirectional Voltage-Level Translation
and GPIO Expansion Between:
– 1.8-V SCL/SDA and
1.8-V, 2.5-V, 3.3-V, or 5-V P Port
– 2.5-V SCL/SDA and
1.8-V, 2.5-V, 3.3-V, or 5-V P Port
– 3.3-V SCL/SDA and
1.8-V, 2.5-V, 3.3-V, or 5-V P Port
– 5-V SCL/SDA and
1.8-V, 2.5-V, 3.3-V, or 5-V P Port
I2C to Parallel Port Expander
Low Standby Current Consumption of 1 μA
Schmitt-Trigger Action Allows Slow Input
Transition and Better Switching Noise
Immunity at the SCL and SDA Inputs
– Vhys = 0.18 V Typ at 1.8 V
– Vhys = 0.25 V Typ at 2.5 V
– Vhys = 0.33 V Typ at 3.3 V
– Vhys = 0.5 V Typ at 5 V
5-V Tolerant I/O Ports
Active-Low Reset (RESET) Input
Open-Drain Active-Low Interrupt (INT) Output
400-kHz Fast I2C Bus
Input/Output Configuration Register
•
•
•
•
•
•
•
•
Polarity Inversion Register
Internal Power-On Reset
Power Up With All Channels Configured as
Inputs
No Glitch On Power Up
Noise Filter on SCL/SDA Inputs
Latched Outputs With High-Current Drive
Maximum Capability for Directly Driving LEDs
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
ESD Protection Exceeds JESD 22
– 2000-V Human-Body Model (A114-A)
– 200-V Machine Model (A115-A)
– 1000-V Charged-Device Model (C101)
RGJ PACKAGE
(BOTTOM VIEW)
P00
P01
P02
P03
P04
P05
P06
P07
•
1 2
3
4
5
6
7
8
INT 32
VCCI 31
9
P10
10 P11
30
11 P12
29
12 P13
28
13 P14
27
14 P15
ADDR 26
GND 25
15 P16
SDA
SCL
RESET
VCCP
16 P17
P27
P26
P25
P24
P23
P22
P21
P20
24 23 22 21 20 19 18 17
DESCRIPTION/ORDERING INFORMATION
This 24-bit I/O expander for the two-line bidirectional bus (I2C) is designed to provide general-purpose remote I/O
expansion for most microcontroller families via the I2C interface [serial clock (SCL) and serial data (SDA)].
The major benefit of this device is its wide VCC range. It can operate from 1.65 V to 5.5 V on the P-port side and
on the SDA/SCL side. This allows the TCA6424 to interface with next-generation microprocessors and
microcontrollers on the SDA/SCL side, where supply levels are dropping down to conserve power. In contrast to
the dropping power supplies of microprocessors and microcontrollers, some PCB components, such as LEDs,
remain at a 5-V power supply.
The bidirectional voltage level translation in the TCA6424 is provided through VCCI. VCCI should be connected to
the VCC of the external SCL/SDA lines. This indicates the VCC level of the I2C bus to the TCA6424. The voltage
level on the P-port of the TCA6424 is determined by the VCCP.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2007–2009, Texas Instruments Incorporated
TCA6424
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
www.ti.com
DESCRIPTION/ORDERING INFORMATION (CONTINUED)
The TCA6424 consists of three 8-bit Configuration (input or output selection), Input, Output, and Polarity
Inversion (active high) registers. At power on, the I/Os are configured as inputs. However, the system master can
enable the I/Os as either inputs or outputs by writing to the I/O configuration bits. The data for each input or
output is kept in the corresponding input or output register. The polarity of the Input Port register can be inverted
with the Polarity Inversion register. All registers can be read by the system master.
The system master can reset the TCA6424 in the event of a timeout or other improper operation by asserting a
low in the RESET input. The power-on reset puts the registers in their default state and initializes the I2C/SMBus
state machine. The RESET pin causes the same reset/initialization to occur without depowering the part.
The TCA6424 open-drain interrupt (INT) output is activated when any input state differs from its corresponding
Input Port register state and is used to indicate to the system master that an input state has changed.
INT can be connected to the interrupt input of a microcontroller. By sending an interrupt signal on this line, the
remote I/O can inform the microcontroller if there is incoming data on its ports without having to communicate via
the I2C bus. Thus, the TCA6424 can remain a simple slave device.
The device P-port outputs have high-current sink capabilities for directly driving LEDs while consuming low
device current.
One hardware pin (ADDR) can be used to program and vary the fixed I2C address and allow up to two devices to
share the same I2C bus or SMBus.
ORDERING INFORMATION
PACKAGE (1)
TA
–40°C to 85°C
(1)
(2)
QFN – RGJ
(2)
Reel of 3000
ORDERABLE PART NUMBER
TCA6424RGJR
TOP-SIDE MARKING
PH424
Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
Table 1. TERMINAL FUNCTIONS
TERMINAL
2
DESCRIPTION
PIN NO.
NAME
1
P00
P-port input/output (push-pull design structure). At power on, P00 is configured as an input.
2
P01
P-port input/output (push-pull design structure). At power on, P01 is configured as an input.
3
P02
P-port input/output (push-pull design structure). At power on, P02 is configured as an input.
4
P03
P-port input/output (push-pull design structure). At power on, P03 is configured as an input.
5
P04
P-port input/output (push-pull design structure). At power on, P04 is configured as an input.
6
P05
P-port input/output (push-pull design structure). At power on, P05 is configured as an input.
7
P06
P-port input/output (push-pull design structure). At power on, P06 is configured as an input.
8
P07
P-port input/output (push-pull design structure). At power on, P07 is configured as an input.
9
P10
P-port input/output (push-pull design structure). At power on, P10 is configured as an input.
10
P11
P-port input/output (push-pull design structure). At power on, P11 is configured as an input.
11
P12
P-port input/output (push-pull design structure). At power on, P12 is configured as an input.
12
P13
P-port input/output (push-pull design structure). At power on, P13 is configured as an input.
13
P14
P-port input/output (push-pull design structure). At power on, P14 is configured as an input.
14
P15
P-port input/output (push-pull design structure). At power on, P15 is configured as an input.
15
P16
P-port input/output (push-pull design structure). At power on, P16 is configured as an input.
16
P17
P-port input/output (push-pull design structure). At power on, P17 is configured as an input.
17
P20
P-port input/output (push-pull design structure). At power on, P20 is configured as an input.
18
P21
P-port input/output (push-pull design structure). At power on, P21 is configured as an input.
19
P22
P-port input/output (push-pull design structure). At power on, P22 is configured as an input.
20
P23
P-port input/output (push-pull design structure). At power on, P23 is configured as an input.
21
P24
P-port input/output (push-pull design structure). At power on, P24 is configured as an input.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
TCA6424
www.ti.com
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
Table 1. TERMINAL FUNCTIONS (continued)
TERMINAL
DESCRIPTION
PIN NO.
NAME
22
P25
P-port input/output (push-pull design structure). At power on, P25 is configured as an input.
23
P26
P-port input/output (push-pull design structure). At power on, P26 is configured as an input.
24
P27
P-port input/output (push-pull design structure). At power on, P27 is configured as an input.
25
GND
Ground
26
ADDR
Address input. Connect directly to VCCP or ground.
27
VCCP
Supply voltage of TCA6424 for P port
28
RESET
29
SCL
Serial clock bus. Connect to VCCI through a pullup resistor.
30
SDA
Serial data bus. Connect to VCCI through a pullup resistor.
31
VCCI
Supply voltage of I2C bus. Connect directly to the VCC of the external I2C master. Provides voltage-level
translation.
32
INT
Interrupt output. Connect to VCCI through a pullup resistor.
Active-low reset input. Connect to VCCP through a pullup resistor, if no active connection is used.
Voltage Translation
Table 2 shows how to set up VCC levels for the necessary voltage translation between the I2C bus and the
TCA6424.
Table 2. Voltage Translation
VCCI (SDA AND SCL OF I2C MASTER)
(V)
VCCP (P PORT)
(V)
1.8
1.8
1.8
2.5
1.8
3.3
1.8
5
2.5
1.8
2.5
2.5
2.5
3.3
2.5
5
3.3
1.8
3.3
2.5
3.3
3.3
3.3
5
5
1.8
5
2.5
5
3.3
5
5
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
3
TCA6424
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
www.ti.com
LOGIC DIAGRAM (POSITIVE LOGIC)
32
INT
Interrupt
Logic
LP Filter
26
ADDR
29
SCL
30
SDA
2
Input
Filter
Shift
Register
I C Bus
Control
31
VCCI
28
RESET
I/O Port
P27–P20
P17–P10
P07–P00
Write Pulse
Read Pulse
27
VCCP
24 Bits
Power-On
Reset
25
GND
A.
All I/Os are set to inputs at reset.
B.
Pin numbers shown are for the RGJ package.
Simplified Schematic of P00 to P27
Data From
Shift Register
Data From
Shift Register
Output Port
Register Data
VCCP
Configuration
Register
D
Q
Q1
FF
Write Configuration
Pulse
CK Q
D
Q
FF
Write Pulse
P00 to P27
CK Q
Output
Port
Register
Q2
Input
Port
Register
Q
D
FF
Read Pulse
ESD Protection Diode
GND
Input Port
Register Data
CK Q
To INT
Data From
Shift Register
D
Q
FF
Write Polarity Pulse
Polarity
Register Data
CK Q
Polarity
Inversion
Register
A.
4
On power up or reset, all registers return to default values.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
TCA6424
www.ti.com
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
I/O Port
When an I/O is configured as an input, FETs Q1 and Q2 are off, which creates a high-impedance input. The
input voltage may be raised above VCC to a maximum of 5.5 V.
If the I/O is configured as an output, Q1 or Q2 is enabled, depending on the state of the output port register. In
this case, there are low-impedance paths between the I/O pin and either VCC or GND. The external voltage
applied to this I/O pin should not exceed the recommended levels for proper operation.
I2C Interface
The bidirectional I2C bus consists of the serial clock (SCL) and serial data (SDA) lines. Both lines must be
connected to a positive supply through a pullup resistor when connected to the output stages of a device. Data
transfer may be initiated only when the bus is not busy.
I2C communication with this device is initiated by a master sending a Start condition, a high-to-low transition on
the SDA input/output, while the SCL input is high (see Figure 1). After the Start condition, the device address
byte is sent, most significant bit (MSB) first, including the data direction bit (R/W).
After receiving the valid address byte, this device responds with an acknowledge (ACK), a low on the SDA
input/output during the high of the ACK-related clock pulse. The address (ADDR) input of the slave device must
not be changed between the Start and the Stop conditions.
On the I2C bus, only one data bit is transferred during each clock pulse. The data on the SDA line must remain
stable during the high pulse of the clock period, as changes in the data line at this time are interpreted as control
commands (Start or Stop) (see Figure 2).
A Stop condition, a low-to-high transition on the SDA input/output while the SCL input is high, is sent by the
master (see Figure 1).
Any number of data bytes can be transferred from the transmitter to receiver between the Start and the Stop
conditions. Each byte of eight bits is followed by one ACK bit. The transmitter must release the SDA line before
the receiver can send an ACK bit. The device that acknowledges must pull down the SDA line during the ACK
clock pulse, so that the SDA line is stable low during the high pulse of the ACK-related clock period (see
Figure 3). When a slave receiver is addressed, it must generate an ACK after each byte is received. Similarly,
the master must generate an ACK after each byte that it receives from the slave transmitter. Setup and hold
times must be met to ensure proper operation.
A master receiver signals an end of data to the slave transmitter by not generating an acknowledge (NACK) after
the last byte has been clocked out of the slave. This is done by the master receiver by holding the SDA line high.
In this event, the transmitter must release the data line to enable the master to generate a Stop condition.
SDA
SCL
S
P
Stop Condition
Start Condition
Figure 1. Definition of Start and Stop Conditions
SDA
SCL
Data Line
Change
Figure 2. Bit Transfer
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
5
TCA6424
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
www.ti.com
Data Output
by Transmitter
NACK
Data Output
by Receiver
ACK
SCL From
Master
1
2
8
9
S
Clock Pulse for
Acknowledgment
Start
Condition
Figure 3. Acknowledgment on the I2C Bus
Table 3. Interface Definition
BYTE
2
I C slave address
I/O data bus
BIT
7 (MSB)
6
5
4
3
2
1
0 (LSB)
L
H
L
L
L
H
ADDR
R/W
P07
P06
P05
P04
P03
P02
P01
P00
P17
P16
P15
P14
P13
P12
P11
P10
P27
P26
P25
P24
P23
P22
P21
P20
Device Address
The address of the TCA6424 is shown in Figure 4.
Slave Address
0
1
0
0
Fixed
0
AD
1 DR R/W
Programmable
Figure 4. TCA6424 Address
Table 4. Address Reference
ADDR
I2C BUS SLAVE ADDRESS
L
34 (decimal), 22 (hexadecimal)
H
35 (decimal), 23 (hexadecimal)
The last bit of the slave address defines the operation (read or write) to be performed. A high (1) selects a read
operation, while a low (0) selects a write operation.
Control Register and Command Byte
Following the successful acknowledgment of the address byte, the bus master sends a command byte, which is
stored in the control register in the TCA6424. Four bits of this data byte state the operation (read or write) and
the internal registers (input, output, polarity inversion, or configuration) that will be affected. The control register
can be written or read through the I2C bus. The command byte is sent only during a write transmission.
6
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
TCA6424
www.ti.com
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
The control register includes an Auto-Increment (AI) bit which is the most significant bit (bit 7) of the command
byte. At power-up, the control register defaults to 00 (hex), with the AI bit set to logic 1, and the lowest 7 bits set
to logic 0.
If AI is 1, the 2 least significant bits are automatically incremented after a read or write. This allows the user to
program and/or read the 3 register banks sequentially. If more than 3 bytes of data are written when AI is 1,
previous data in the selected registers will be overwritten. Reserved registers are skipped and not accessed
(refer to Table 5).
If AI is 0, the 2 least significant bits are not incremented after data is read or written. During a read operation, the
same register bank is read each time. During a write operation, data is written to the same register bank each
time.
Reserved command codes and command byte outside the range stated in the Command Byte table must not be
accessed for proper device functionality.
AI
B6
B5
B4
B3
B2
B1
B0
Figure 5. Control Register Bits
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
7
TCA6424
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
www.ti.com
Table 5. Command Byte
CONTROL REGISTER BITS
AI
B6
B5
B4
B3
B2
B1
B0
AUTOINCREMENT
STATE
0
0
0
0
0
0
0
0
Disable
00
1
0
0
0
0
0
0
0
Enable
80
0
0
0
0
0
0
0
1
Disable
01
1
0
0
0
0
0
0
1
Enable
81
0
0
0
0
0
0
1
0
Disable
02
1
0
0
0
0
0
1
0
Enable
82
0
0
0
0
0
0
1
1
Disable
03
1
0
0
0
0
0
1
1
Enable
83
0
0
0
0
0
1
0
0
Disable
04
1
0
0
0
0
1
0
0
Enable
84
0
0
0
0
0
1
0
1
Disable
05
1
0
0
0
0
1
0
1
Enable
85
0
0
0
0
0
1
1
0
Disable
06
1
0
0
0
0
1
1
0
Enable
86
0
0
0
0
0
1
1
1
Disable
07
1
0
0
0
0
1
1
1
Enable
87
0
0
0
0
1
0
0
0
Disable
08
1
0
0
0
1
0
0
0
Enable
88
0
0
0
0
1
0
0
1
Disable
09
1
0
0
0
1
0
0
1
Enable
89
0
0
0
0
1
0
1
0
Disable
0A
1
0
0
0
1
0
1
0
Enable
8A
0
0
0
0
1
0
1
1
Disable
0B
1
0
0
0
1
0
1
1
Enable
8B
0
0
0
0
1
1
0
0
Disable
0C
1
0
0
0
1
1
0
0
Enable
8C
0
0
0
0
1
1
0
1
Disable
0D
1
0
0
0
1
1
0
1
Enable
8D
0
0
0
0
1
1
1
0
Disable
0E
1
0
0
0
1
1
1
0
Enable
8E
0
0
0
0
1
1
1
1
Disable
0F
1
0
0
0
1
1
1
1
Enable
8F
(1)
8
COMMAND
BYTE
(HEX)
REGISTER
PROTOCOL
POWER-UP
DEFAULT
Input Port 0
Read byte
xxxx xxxx (1)
Input Port 1
Read byte
xxxx xxxx (1)
Input Port 2
Read byte
xxxx xxxx (1)
Reserved
Reserved
Reserved
Output Port 0
Read/write
byte
1111 1111
Output Port 1
Read/write
byte
1111 1111
Output Port 2
Read/write
byte
1111 1111
Reserved
Reserved
Reserved
Polarity Inversion
Port 0
Read/write
byte
0000 0000
Polarity Inversion
Port 1
Read/write
byte
0000 0000
Polarity Inversion
Port 2
Read/write
byte
0000 0000
Reserved
Reserved
Reserved
Configuration Port 0
Read/write
byte
1111 1111
Configuration Port 1
Read/write
byte
1111 1111
Configuration Port 2
Read/write
byte
1111 1111
Reserved
Reserved
Reserved
Undefined
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
TCA6424
www.ti.com
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
Register Descriptions
The Input Port registers (registers 0, 1 and 2) reflect the incoming logic levels of the pins, regardless of whether
the pin is defined as an input or an output by the Configuration register. They act only on read operation. Writes
to these registers have no effect. The default value (X) is determined by the externally applied logic level. Before
a read operation, a write transmission is sent with the command byte to indicate to the I2C device that the Input
Port register will be accessed next.
Table 6. Registers 0 and 1 (Input Port Registers)
BIT
I-07
I-06
I-05
I-04
I-03
I-02
I-01
I-00
DEFAULT
X
X
X
X
X
X
X
X
I-10
BIT
I-17
I-16
I-15
I-14
I-13
I-12
I-11
DEFAULT
X
X
X
X
X
X
X
X
BIT
I-27
I-26
I-25
I-24
I-23
I-22
I-21
I-20
DEFAULT
X
X
X
X
X
X
X
X
The Output Port registers (registers 4, 5 and 6) shows the outgoing logic levels of the pins defined as outputs by
the Configuration register. Bit values in these registers have no effect on pins defined as inputs. In turn, reads
from these registers reflect the value that is in the flip-flop controlling the output selection, NOT the actual pin
value.
Table 7. Registers 2 and 3 (Output Port Registers)
BIT
O-07
O-06
O-05
O-04
O-03
O-02
O-01
O-00
DEFAULT
1
1
1
1
1
1
1
1
BIT
O-17
O-16
O-15
O-14
O-13
O-12
O-11
O-10
DEFAULT
1
1
1
1
1
1
1
1
BIT
O-27
O-26
O-25
O-24
O-23
O-22
O-21
O-20
DEFAULT
1
1
1
1
1
1
1
1
The Polarity Inversion registers (registers 8, 9 and 10) allow polarity inversion of pins defined as inputs by the
Configuration register. If a bit in these registers is set (written with 1), the corresponding port pin's polarity is
inverted. If a bit in these registers is cleared (written with a 0), the corresponding port pin's original polarity is
retained.
Table 8. Registers 4 and 5 (Polarity Inversion Registers)
BIT
P-07
P-06
P-05
P-04
P-03
P-02
P-01
P-00
DEFAULT
0
0
0
0
0
0
0
0
BIT
P-17
P-16
P-15
P-14
P-13
P-12
P-11
P-10
DEFAULT
0
0
0
0
0
0
0
0
BIT
P-27
P-26
P-25
P-24
P-23
P-22
P-21
P-20
DEFAULT
0
0
0
0
0
0
0
0
The Configuration registers (registers 12, 13 and 14) configure the direction of the I/O pins. If a bit in these
registers is set to 1, the corresponding port pin is enabled as an input with a high-impedance output driver. If a
bit in these registers is cleared to 0, the corresponding port pin is enabled as an output.
Table 9. Registers 6 and 7 (Configuration Registers)
BIT
C-07
C-06
C-05
C-04
C-03
C-02
C-01
DEFAULT
1
1
1
1
1
1
1
C-00
1
BIT
C-17
C-16
C-15
C-14
C-13
C-12
C-11
C-10
DEFAULT
1
1
1
1
1
1
1
1
BIT
C-27
C-26
C-25
C-24
C-23
C-22
C-21
C-20
DEFAULT
1
1
1
1
1
1
1
1
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
9
TCA6424
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
www.ti.com
Power-On Reset
When power (from 0 V) is applied to VCCP, an internal power-on reset holds the TCA6424 in a reset condition
until VCCP has reached VPOR. At that time, the reset condition is released, and the TCA6424 registers and
I2C/SMBus state machine initializes to their default states. After that, VCCP must be lowered to below 0.2 V and
back up to the operating voltage for a power-reset cycle.
Reset Input (RESET)
The RESET input can be asserted to initialize the system while keeping the VCCP at its operating level. A reset
can be accomplished by holding the RESET pin low for a minimum of tW. The TCA6424 registers and I2C/SMBus
state machine are changed to their default state once RESET is low (0). When RESET is high (1), the I/O levels
at the P port can be changed externally or through the master. This input requires a pullup resistor to VCCP, if no
active connection is used.
Interrupt (INT)Output
An interrupt is generated by any rising or falling edge of the port inputs in the input mode. After time tiv, the signal
INT is valid. Resetting the interrupt circuit is achieved when data on the port is changed to the original setting,
data is read from the port that generated the interrupt or in a stop event. Resetting occurs in the read mode at
the acknowledge (ACK) or not acknowledge (NACK) bit after the rising edge of the SCL signal. Interrupts that
occur during the ACK or NACK clock pulse can be lost (or be very short) due to the resetting of the interrupt
during this pulse. Each change of the I/Os after resetting is detected and is transmitted as INT.
Reading from or writing to another device does not affect the interrupt circuit, and a pin configured as an output
cannot cause an interrupt. Changing an I/O from an output to an input may cause a false interrupt to occur, if the
state of the pin does not match the contents of the Input Port register.
In the TCA6424, an interrupt is not immediately generated by any rising or falling edge of port inputs in input
mode after issuing any I2C commands (read or write). In order to capture the INT in the TCA6424, the user
needs to add one more SCL clock pulse after a Stop signal.
The INT output has an open-drain structure and requires a pullup resistor to VCCP or VCCI depending on the
application. If the INT signal is connected back to the processor that provides the SCL signal to the TCA6424,
then the INT pin has to be connected to VCCI. If not, the INT pin can be connected to VCCP.
Bus Transactions
Data is exchanged between the master and TCA6424 through write and read commands.
Writes
Data is transmitted to the TCA6424 by sending the device address and setting the least-significant bit (LSB) to a
logic 0 (see Figure 4 for device address). The command byte is sent after the address and determines which
register receives the data that follows the command byte. There is no limitation on the number of data bytes sent
in one write transmission.
The twelve registers within the TCA6424 are grouped into four different sets. The four sets of registers are input
ports, output ports, polarity inversion ports and configuration ports. After sending data to one register, the next
data byte is sent to the next register in the group of 3 registers (see Figure 6 and Figure 7). For example, if the
first byte is send to Output Port 2 (register 6), the next byte is stored in Output Port 0 (register 4).
There is no limitation on the number of data bytes sent in one write transmission. In this way, each 8-bit register
may be updated independently of the other registers.
10
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
TCA6424
www.ti.com
SCL
1
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
2
3
4
5
6
7
8
9
Command Byte
Slave Address
SDA
0
S
1
0
0 0
1 AD
DR 0
A 0
0
0
0
0
Data to Port 0
1 0/1 0/1 A 0.7
R/W Acknowledge
From Slave
Start Condition
Data to Port 1
0.0 A 1.7
Data 0
Acknowledge
From Slave
Data 1
1.0 A
P
Acknowledge
From Slave
Write to Port
Data Out from Port 0
tpv
Data Valid
Data Out from Port 1
tpv
Figure 6. Write to Output Port Register
<br/>
SCL
1
2
3
4
5
6
7
8
9
1
3
2
Slave Address
SDA
S
0
1
0
Start Condition
0
0
4
5
6
7
8
9
1
1 AD
DR 0
A
0
0
0
R/W Acknowledge
From Slave
0
2
3
4
5
6
7
8
9
1
Data to Register
Command Byte
1 0/1 0/1 0/1 A MSB
Data 0
Acknowledge
From Slave
3
2
4
5
Data to Register
LSB A MSB
Data1
LSB A
P
Acknowledge
From Slave
Figure 7. Write to Configuration or Polarity Inversion Registers
Reads
The bus master first must send the TCA6424 address with the LSB set to a logic 0 (see Figure 4 for device
address). The command byte is sent after the address and determines which register is accessed.
After a restart, the device address is sent again but, this time, the LSB is set to a logic 1. Data from the register
defined by the command byte then is sent by the TCA6424 (see Figure 8 and Figure 9).
After a restart, the value of the register defined by the command byte matches the register being accessed when
the restart occurred. For example, if the command byte references Input Port 1 before the restart, and the restart
occurs when Input Port 0 is being read, the stored command byte changes to reference Input Port 0. The original
command byte is forgotten. If a subsequent restart occurs, Input Port 0 is read first. Data is clocked into the
register on the rising edge of the ACK clock pulse. After the first byte is read, additional bytes may be read, but
the data now reflects the information in the other register in the pair. For example, if Input Port 1 is read, the next
byte read is Input Port 0.
Data is clocked into the register on the rising edge of the ACK clock pulse. There is no limitation on the number
of data bytes received in one read transmission, but when the final byte is received, the bus master must not
acknowledge the data.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
11
TCA6424
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
0
0
1
0
0
Acknowledge
From Slave
Acknowledge
From Slave
Slave Address
S
www.ti.com
1 AD
DR 0
Command Byte
A
R/W
A
S
Acknowledge
From Slave
Slave Address
0
1
0
0
0
AD 1
DR
1
Data
A MSB
LSB A
First Byte
R/W
At this moment, master transmitter
becomes master receiver, and
slave receiver becomes slave transmitter.
Data From Lower
or Upper Byte Acknowledge
of Register
From Master
Data From Upper
or Lower Byte No Acknowledge
of Register
From Master
MSB
Data
LSB NA P
Last Byte
Figure 8. Read From Register
<br/>
SCL
1
2
3
4
5
6
7
8
9
I0.x
SDA
S 0 1 0 0 0 1
AD
DR
1 A
Data 1
R/W Acknowledge
From Slave
I1.x
A
Data 2
Acknowledge
From Master
I2.x
A
Data 3
Acknowledge
From Master
I0.x
A
Data 4
Acknowledge
From Master
1 P
No Acknowledge
From Master
Read From
Port 0
Data Into
Port 0
Read From
Port 1
Data Into
Port 1
INT
tiv
tir
Read From
Port 2
Data Into
Port 2
A.
Transfer of data can be stopped at any time by a Stop condition. When this occurs, data present at the latest
acknowledge phase is valid (output mode). It is assumed that the command byte previously has been set to 00 (read
Input Port register).
B.
This figure eliminates the command byte transfer, a restart, and slave address call between the initial slave address
call and actual data transfer from P port (see Figure 8).
C.
Auto-increment mode is enabled.
Figure 9. Read Input Port Register
12
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
TCA6424
www.ti.com
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
VCCI
Supply voltage range
–0.5
6.5
V
VCCP
Supply voltage range
–0.5
6.5
V
VI
Input voltage range (2)
–0.5
6.5
V
VO
Output voltage range (2)
–0.5
6.5
V
IIK
Input clamp current
ADDR, RESET, SCL
VI < 0
±20
mA
IOK
Output clamp current
INT
VO < 0
±20
mA
P port
VO < 0 or VO > VCCP
±20
SDA
VO < 0 or VO > VCCI
±20
P port
VO = 0 to VCCP
25
SDA, INT
VO = 0 to VCCI
15
P port
VO = 0 to VCCP
25
IIOK
Input/output clamp current
IOL
Continuous output low current
IOH
Continuous output high current
ICC
Continuous current through GND
200
Continuous current through VCCP
160
Continuous current through VCCI
10
θJA
Package thermal impedance (3)
Tstg
Storage temperature range
(1)
(2)
(3)
RGJ package
50.05
–65
150
UNIT
mA
mA
mA
mA
°C/W
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed.
The package thermal impedance is calculated in accordance with JESD 51-7.
RECOMMENDED OPERATING CONDITIONS
MIN
MAX
VCCI
Supply voltage
1.65
5.5
VCCP
Supply voltage
1.65
5.5
VIH
High-level input voltage
SCL, SDA
0.7 × VCCI
5.5
ADDR, P27–P00, RESET
0.7 × VCCP
5.5
VIL
Low-level input voltage
IOH
High-level output current
P27–P00
10
mA
IOL
Low-level output current
P27–P00
25
mA
TA
Operating free-air temperature
85
°C
SCL, SDA
–0.5
0.3 × VCCI
ADDR, P27–P00, RESET
–0.5
0.3 × VCCP
–40
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
UNIT
V
V
V
13
TCA6424
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
www.ti.com
ELECTRICAL CHARACTERISTICS
over recommended operating free-air temperature range, VCCI = 1.65 V to 5.5 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCCP
MIN
–1.2
VIK
Input diode clamp
voltage
II = –18 mA
1.65 V to 5.5 V
VPOR
Power-on reset voltage
VI = VCCP or GND, IO = 0
1.65 V to 5.5 V
IOH = –8 mA
P-port high-level output
voltage
VOH
IOH = –10 mA
IOL = 8mA
P-port low-level output
voltage
VOL
IOL = 10 mA
TYP (1)
1.2
2.3 V
1.8
3V
2.6
4.5 V
4.1
1.65 V
1
2.3 V
1.7
3V
2.5
4.5 V
4.0
2.3 V
0.25
3V
0.25
4.5 V
0.23
1.65 V
0.6
2.3 V
0.3
3V
0.25
4.5 V
3
INT
VOL = 0.4 V
1.65 V to 5.5 V
3
SCL, SDA
VI = VCCI or GND
ADDR, RESET
VI = VCCP or GND
IIH
P port
VI = VCCP
IIL
P port
VI = GND
ICC
(ICCP + ICCI)
Standby
mode
ΔICCI
μA
1
μA
8
30
SDA,
P port,
ADDR,
RESET
VI on SDA = VCCI or GND,
VI on P port, ADDR and
RESET = VCCP,
IO = 0, I/O = inputs,
fSCL = 100 kHz
1.65 V to 5.5 V
1.7
10
SCL,
SDA,
P port,
ADDR,
RESET
VI on SCL and SDA = VCCI or
GND,
VI on P port, ADDR and
RESET = VCCP,
IO = 0, I/O = inputs,
fSCL = 0
1.65 V to 5.5 V
0.1
2
SCL,
SDA
One input at VCCI – 0.6 V,
Other inputs at VCCI or GND
P port,
ADDR,
RESET
One input at VCCP – 0.6 V,
Other inputs at VCCP or GND
VI = VCCI or GND
SDA
VIO = VCCI or GND
P port
VIO = VCCP or GND
μA
1
1.65 V to 5.5 V
SCL
14
±0.1
VI on SDA = VCCI or GND,
VI on P port, ADDR and
RESET = VCCP,
IO = 0, I/O = inputs,
fSCL = 400 kHz
CI
(1)
±0.1
1.65 V to 5.5 V
SDA,
P port,
ADDR,
RESET
ΔICCP
Cio
mA
15
1.65 V to 5.5 V
Additional
current in
Standby
mode
V
0.24
1.65 V to 5.5 V
Operating
mode
V
V
0.45
VOL = 0.4 V
II
1.4
1.65 V
SDA
IOL
UNIT
V
1
1.65 V
MAX
μA
25
μA
1.65 V to 5.5 V
60
1.65 V to 5.5 V
1.65 V to 5.5 V
6
7
7
8
7.5
8.5
pF
pF
Except for ICC, all typical values are at nominal supply voltage (VCCP = VCCI =1.8-V, 2.5-V, 3.3-V, or 5-V VCC) and TA = 25°C. For ICC, all
typical values are at VCCP = VCCI = 3.3 V and TA = 25°C.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
TCA6424
www.ti.com
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
I2C INTERFACE TIMING REQUIREMENTS
over recommended operating free-air temperature range (unless otherwise noted) (see Figure 10)
STANDARD MODE
I2C BUS
MIN
MAX
100
FAST MODE
I2C BUS
UNIT
MIN
MAX
0
400
fscl
I2C clock frequency
0
tsch
I2C clock high time
4
0.6
μs
tscl
I2C clock low time
4.7
1.3
μs
2
tsp
I C spike time
tsds
I2C serial data setup time
tsdh
I2C serial data hold time
0
50
0
50
kHz
ns
250
100
ns
0
0
ns
2
ticr
I C input rise time
1000
20 + 0.1Cb
(1)
ticf
I2C input fall time
300
20 + 0.1Cb
(1)
300
ns
tocf
I2C output fall time; 10 pF to 400 pF bus
300
20 + 0.1Cb
(1)
300
μs
tbuf
I2C bus free time between Stop and Start
2
300
ns
4.7
1.3
μs
tsts
I C Start or repeater Start condition setup time
4.7
0.6
μs
tsth
I2C Start or repeater Start condition hold time
4
0.6
μs
tsps
I2C Stop condition setup time
4
0.6
μs
tvd(data)
Valid data time; SCL low to SDA output valid
1
1
μs
tvd(ack)
Valid data time of ACK condition; ACK signal from SCL low to SDA
(out) low
1
1
μs
(1)
Cb = total capacitance of one bus line in pF
RESET TIMING REQUIREMENTS
over recommended operating free-air temperature range (unless otherwise noted) (see Figure 13)
STANDARD MODE
I2C BUS
MIN
tW
Reset pulse duration
tREC
Reset recovery time
4
tRESET Time to reset (1)
(1)
MAX
FAST MODE
I2C BUS
MIN
UNIT
MAX
4
ns
0
0
ns
600
600
ns
Minimum time for SDA to become high or minimum time to wait before doing a START.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
15
TCA6424
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
www.ti.com
Switching Characteristics
over recommended operating free-air temperature range, CL ≤ 100 pF (unless otherwise noted) (see Figure 10)
PARAMETER
FROM
TO
STANDARD MODE
I2C BUS
MIN
FAST MODE
I2C BUS
MAX
MIN
UNIT
MAX
tIV
Interrupt valid time
P port
INT
4
4
μs
tIR
Interrupt reset delay time
SCL
INT
4
4
μs
tPV
Output data valid
SCL
P27–P00
400
400
ns
tPS
Input data setup time
P port
SCL
0
0
ns
tPH
Input data hold time
P port
SCL
300
300
ns
16
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
TCA6424
www.ti.com
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
TYPICAL CHARACTERISTICS
TA = 25°C (unless otherwise noted)
100
Supply Current, ICC (µA)
80
VCC = 5 V
70
60
50
VCC = 3.3 V
40
30
VCC = 2.5 V
20
VCC = 1.8 V
10
0
-40
-15
8
100
SCL = VCC
All I/Os unloaded
6
VCC = 3.3 V
5
VCC = 2.5 V
4
3
2
10
35
60
85
2
0
0.2
0.3
0.4
0.5
18
TA = 25°C
16
14
12
10
8
TA = 85°C
6
4
Output Low Voltage, VOL (mV)
Sink Current, ISINK (mA)
TA = 25°C
30
25
20
15
TA = 85°C
0
0.2
0.3
0.4
15
0.2
0.3
0.4
0.5
TA = 85°C
10
0.6
0
0.5
Output Low Voltage, VOL (V)
0.1
0.2
0.3
0.4
0.5
0.6
Output Low Voltage, VOL (V)
I/O LOW VOLTAGE
vs
TEMPERATURE
TA = –40°C
0.1
0.1
I/O SOURCE CURRENT
vs
OUTPUT HIGH VOLTAGE
400
5
20
Output Low Voltage, VOL (V)
VCC = 5 V
10
25
5
0
TA = 25°C
30
0
I/O SINK CURRENT
vs
OUTPUT LOW VOLTAGE
40
35
2
Output Low Voltage, VOL (V)
TA = –40°C
40
0
0.6
VCC = 3.3 V
45
TA = –40°C
20
VCC = 1.8 V
350
Source Current, ISOURCE (mA)
0.1
50
Sink Current, ISINK (mA)
TA = 85°C
0
0
1.65 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
85
VCC = 2.5 V
22
20
TA = –40°C
4
35
20
I/O SINK CURRENT
vs
OUTPUT LOW VOLTAGE
6
45
30
I/O SINK CURRENT
vs
OUTPUT LOW VOLTAGE
8
50
40
I/O SINK CURRENT
vs
OUTPUT LOW VOLTAGE
10
0
60
50
Supply Voltage, VCC (V)
TA = 25°C
12
35
60
Temperature, TA (°C)
16
14
10
70
Temperature, TA (°C)
VCC = 1.8 V
18
–15
80
10
VCC = 1.8 V
0
–40
fSCL = 400 kHz
All I/Os unloaded
90
VCC = 5 V
7
24
20
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
1
Sink Current, ISINK (mA)
Supply Current, ICC (µA)
9
fSCL = 400 kHz
All I/Os unloaded
90
Sink Current, ISINK (mA)
STANDBY SUPPLY CURRENT
vs
TEMPERATURE
Supply Current, ICC (µA)
SUPPLY CURRENT
vs
TEMPERATURE
VCC = 5 V, ISINK = 10 mA
300
250
200
150
100
50
0
−40
VCC = 1.8 V, ISINK = 10 mA
VCC = 5 V, ISINK = 1 mA
VCC = 1.8 V, ISINK = 1 mA
TA = –40°C
16
TA = 25°C
12
8
TA = 85°C
4
0
−15
10
35
60
Temperature, TA (°C)
85
0
0.1
0.2
0.3
0.4
0.5
0.6
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
0.7
VCC – VOH (V)
17
TCA6424
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
www.ti.com
TYPICAL CHARACTERISTICS (continued)
TA = 25°C (unless otherwise noted)
I/O SOURCE CURRENT
vs
OUTPUT HIGH VOLTAGE
I/O SOURCE CURRENT
vs
OUTPUT HIGH VOLTAGE
50
50
VCC = 2.5 V
VCC = 3.3 V
45
Source Current, ISOURCE (mA)
TA = –40°C
20
TA = 25°C
15
10
TA = 85°C
5
TA = –40°C
40
35
TA = 25°C
30
25
20
15
TA = 85°C
10
5
0
0.1
0.2
0.3
0.4
0.5
0.6
0
0.7
TA = –40°C
40
TA = 25°C
35
30
25
20
15
TA = 85°C
10
5
0
0
0
VCC = 5 V
45
Source Current, ISOURCE (mA)
25
Source Current, ISOURCE (mA)
I/O SOURCE CURRENT
vs
OUTPUT HIGH VOLTAGE
0.1
0.2
0.3
0.4
0.6 0.7
0.5
0.1
0.2
0.3
0.4
0.5
0.6
VCC – VOH (V)
VCC – VOH (V)
VCC – VOH (V)
0
I/O HIGH VOLTAGE
vs
TEMPERATURE
5
VCC – VOH (V)
4
3
VCC = 1.8 V, ISOURCE = 10 mA
2
1
VCC = 5 V, ISOURCE = 10 mA
0
−40
−15
10
35
60
85
Temperature, TA (°C)
18
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
TCA6424
www.ti.com
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
PARAMETER MEASUREMENT INFORMATION
VCCI
RL = 1 kW
SDA
DUT
CL = 50 pF
(see Note A)
SDA LOAD CONFIGURATION
Two Bytes for READ Input Port Register
(see Figure 9)
Address
Bit 7
(MSB)
Stop
Start
Condition Condition
(P)
(S)
tscl
Address
Bit 1
R/W
Bit 0
(LSB)
Data
Bit 7
(MSB)
ACK
(A)
Data
Bit 0
(LSB)
Stop
Condition
(P)
tsch
0.7 ´ VCCI
SCL
0.3 ´ VCCI
ticr
ticf
tbuf
tvd
tsp
tocf
tvd
tsts
tsps
SDA
0.7 ´ VCCI
0.3 ´ VCCI
ticr
ticf
tsth
tsdh
tsds
tvd(ack)
Repeat Start
Condition
Stop
Condition
VOLTAGE WAVEFORMS
BYTE
DESCRIPTION
2
1
I C address
2
Input register port data
A.
CL includes probe and jig capacitance. tocf is measured with CL of 10 pF or 400 pF.
B.
All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns.
C.
All parameters and waveforms are not applicable to all devices.
Figure 10. I2C Interface Load Circuit and Voltage Waveforms
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
19
TCA6424
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
www.ti.com
PARAMETER MEASUREMENT INFORMATION (continued)
VCCI
RL = 4.7 kW
INT
DUT
CL = 100 pF
(see Note A)
INTERRUPT LOAD CONFIGURATION
ACK
From Slave
Start
Condition
8 Bits
(One Data Byte)
From Port
R/W
Slave Address
S
0
1
0
0
0
AD
1 DR 1
A
1
2
3
4
5
6
A
7
8
Data 1
ACK
From Slave
Data From Port
Data 2
A
1
P
A
tir
tir
B
B
INT
tiv
A
tsps
A
Data
Into
Port
Address
Data 1
0.5 ´ VCCI
INT
SCL
Data 2
0.7 ´ VCCI
R/W
tiv
A
tir
0.5 ´ VCCP
Pn
0.5 ´ VCCI
INT
View A−A
View B−B
A.
CL includes probe and jig capacitance.
B.
All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns.
C.
All parameters and waveforms are not applicable to all devices.
Figure 11. Interrupt Load Circuit and Voltage Waveforms
20
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
TCA6424
www.ti.com
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
PARAMETER MEASUREMENT INFORMATION (continued)
500 W
Pn
DUT
2 ´ VCCP
CL = 50 pF
(see Note A)
500 W
P PORT LOAD CONFIGURATION
SCL
P0
A
P3
0.7 ´ VCCP
0.3 ´ VCCI
Slave
ACK
SDA
tpv
(see Note B)
Pn
Unstable
Data
Last Stable Bit
WRITE MODE (R/W = 0)
SCL
0.7 ´ VCCI
P0
A
tps
P3
0.3 ´ VCCI
tph
Pn
0.5 ´ VCCP
READ MODE (R/W = 1)
A.
CL includes probe and jig capacitance.
B.
tpv is measured from 0.7 × VCC on SCL to 50% I/O (Pn) output.
C.
All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns.
D.
The outputs are measured one at a time, with one transition per measurement.
E.
All parameters and waveforms are not applicable to all devices.
Figure 12. P-Port Load Circuit and Timing Waveforms
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
21
TCA6424
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
www.ti.com
PARAMETER MEASUREMENT INFORMATION (continued)
VCCI
R L = 1 kW
500 W
Pn
SDA
DUT
DUT
CL = 50 pF
(see Note A)
SDA LOAD CONFIGURATION
2 ´ VCCP
CL = 50 pF
(see Note A)
500 W
P PORT LOAD CONFIGURATION
Start
SCL
ACK or Read Cycle
SDA
0.3 ´ VCCI
tRESET
VCCP/2
RESET
tREC
tREC
tW
VCCP/2
Pn
tRESET
A.
CL includes probe and jig capacitance.
B.
All inputs are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr/tf ≤ 30 ns.
C.
The outputs are measured one at a time, with one transition per measurement.
D.
I/Os are configured as inputs.
E.
All parameters and waveforms are not applicable to all devices.
Figure 13. Reset Load Circuits and Voltage Waveforms
22
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
TCA6424
www.ti.com
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
APPLICATION INFORMATION
Figure 14 shows an application in which the TCA6424 can be used.
VCCI VCCP
10 kW (x 7)
VCCI
(1.8 V)
10 kW
VCC
10 kW
10 kW
29
SCL
Master
Controller SDA
30
32
INT
GND
31
10 kW
29
RESET
27
VCCI
VCCP
P00
SCL
23
22
21
Status
Monitor
20
19
18
17
26
1
A
SDA
P01
INT
2
ENABLE
RESET
TCA6424
24
ALARM
(See Note D)
Subsystem 1
(e.g., Alarm)
P27
P26
P25
P24
P23
P22
P21
P20
ADDR
GND
P02
P03
P04
P05
P06
P07
P10
P11
P12
P13
P14
P15
P16
P17
B
3
4
5
6
7
8
9
10
Keypad
11
12
13
14
15
16
25
A.
Device address configured as 0100000 for this example.
B.
P00 and P02–P10 are configured as inputs.
C.
P01, P11-P17, and P20-P27 are configured as outputs.
D.
Resistors are required for inputs (on P port) that may float. If a driver to an input will not let the input float, a resistor is
not needed. Outputs (in the P port) do not need pullup resistors.
Figure 14. Typical Application
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
23
TCA6424
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
www.ti.com
Minimizing ICC When I/Os Control LEDs
When the I/Os are used to control LEDs, normally they are connected to VCC through a resistor as shown in
Figure 14. The LED acts as a diode so, when the LED is off, the I/O VIN is about 1.2 V less than VCC. The ΔICC
parameter in Electrical Characteristics shows how ICC increases as VIN becomes lower than VCC. Designs that
must minimize current consumption, such as battery power applications, should consider maintaining the I/O pins
greater than or equal to VCC when the LED is off.
Figure 15 shows a high-value resistor in parallel with the LED. Figure 16 shows VCC less than the LED supply
voltage by at least 1.2 V. Both of these methods maintain the I/O VIN at or above VCC and prevent additional
supply current consumption when the LED is off.
VCC
LED
100 kW
VCC
Px
Figure 15. High-Value Resistor in Parallel With the LED
3.3 V
5V
LED
VCC
Px
Figure 16. Device Supplied by a Low Voltage
Power-On Reset Requirements
In the event of a glitch or data corruption, TCA6424 can be reset to its default conditions by using the power-on
reset feature. Power-on reset requires that the device go through a power cycle to be completely reset. This
reset also happens when the device is powered on for the first time in an application.
The two types of power-on reset are shown in Figure 17 and Figure 18.
VCC
Ramp-Up
Ramp-Down
Re-Ramp-Up
VCC_TRR_GND
Time
VCC_RT
VCC_FT
Time to Re-Ramp
VCC_RT
Figure 17. VCC is Lowered Below 0.2 V or 0 V and Then Ramped Up to VCC
24
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
TCA6424
www.ti.com
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
VCC
Ramp-Down
Ramp-Up
VCC_TRR_VPOR50
VIN drops below POR levels
Time
Time to Re-Ramp
VCC_FT
VCC_RT
Figure 18. VCC is Lowered Below the POR Threshold, Then Ramped Back Up to VCC
Table
2
RECOMMENDED SUPPLY SEQUENCING AND RAMP RATES specifies the performance of the power-on reset
feature for TCA6424 for both types of power-on reset.
Table 2
RECOMMENDED SUPPLY SEQUENCING AND RAMP RATES
TA = –40°C to 85°C (unless otherwise noted)
MAX
UNIT
VCC_FT
Fall rate
PARAMETER
See Figure 17
MIN
1
TYP
100
ms
VCC_RT
Rise rate
See Figure 17
0.01
100
ms
VCC_TRR_GND
Time to re-ramp (when VCC drops to GND)
See Figure 17
0.001
ms
VCC_TRR_POR50
Time to re-ramp (when VCC drops to VPOR_MIN – 50 mV)
See Figure 18
0.001
ms
VCC_GH
Level that VCCP can glitch down to, but not cause a functional
disruption when VCCX_GW = 1 μs
See Figure 19
VCC_GW
Glitch width that will not cause a functional disruption when
VCCX_GH = 0.5 × VCCx
See Figure 19
VPORF
Voltage trip point of POR on falling VCC
0.767
1.144
V
VPORR
Voltage trip point of POR on fising VCC
1.033
1.428
V
1.2
V
μs
Glitches in the power supply can also affect the power-on reset performance of this device.
(VCC_GW) and height (VCC_GH) are dependent on each other. The bypass capacitance, source
device impedance are factors that affect power-on reset performance. Figure 19
RECOMMENDED SUPPLY SEQUENCING AND RAMP RATES provide more information on
these specifications.
The glitch width
impedance, and
and Table 2
how to measure
VCC
VCC_GH
Time
VCC_GW
Figure 19. Glitch Width and Glitch Height
VPOR is critical to the power-on reset. VPOR is the voltage level at which the reset condition is released and all the
registers and the I2C/SMBus state machine are initialized to their default states. The value of VPOR differs based
on
the
VCC
being
lowered
to
or
from
0.
Figure
20
and
Table
2
RECOMMENDED SUPPLY SEQUENCING AND RAMP RATES provide more details on this specification.
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
25
TCA6424
SCPS175A – NOVEMBER 2007 – REVISED NOVEMBER 2009
www.ti.com
VCC
VPOR
VPORF
Time
POR
Time
Figure 20. VPOR
26
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TCA6424
PACKAGE OPTION ADDENDUM
www.ti.com
17-Jul-2010
PACKAGING INFORMATION
Orderable Device
TCA6424RGJR
Status
(1)
ACTIVE
Package Type Package
Drawing
UQFN
RGJ
Pins
Package Qty
32
3000
Eco Plan
TBD
(2)
Lead/
Ball Finish
Call TI
MSL Peak Temp
(3)
Samples
(Requires Login)
Call TI
Request Free Samples
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DLP® Products
www.dlp.com
Communications and
Telecom
www.ti.com/communications
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
www.ti.com/clocks
Consumer Electronics
www.ti.com/consumer-apps
Interface
interface.ti.com
Energy
www.ti.com/energy
Logic
logic.ti.com
Industrial
www.ti.com/industrial
Power Mgmt
power.ti.com
Medical
www.ti.com/medical
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
www.ti.com/video
Wireless
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated