LM5112 Tiny 7A MOSFET Gate Driver General Description Features The LM5112 MOSFET gate driver provides high peak gate drive current in the tiny LLP-6 package (SOT23 equivalent footprint) with improved package power dissipation required for high frequency operation. The compound output driver stage includes MOS and bipolar transistors operating in parallel that together sink more than 7A peak from capacitive loads. Combining the unique characteristics of MOS and bipolar devices reduces drive current variation with voltage and temperature. Under-voltage lockout protection is provided to prevent damage to the MOSFET due to insufficient gate turn-on voltage. The LM5112 provides both inverting and non-inverting inputs to satisfy requirements for inverting and non-inverting gate drive with a single device type. n Compound CMOS and bipolar outputs reduce output current variation n 7A sink/3A source current n Fast propagation times (25 ns typical) n Fast rise and fall times (14 ns/12 ns rise/fall with 2 nF load) n Inverting and non-inverting inputs provide either configuration with a single device n Supply rail under-voltage lockout protection n Dedicated input ground (IN_REF) for split supply or single supply operation n Power Enhanced 6-pin LLP package (3.0mm x 3.0mm) n Output swings from VCC to VEE which can be negative relative to input ground Block Diagram 20066801 Block Diagram of LM5112 © 2004 National Semiconductor Corporation DS200668 www.national.com LM5112 Tiny 7A MOSFET Gate Driver October 2004 LM5112 Pin Configurations 20066802 LLP-6 Ordering Information Order Number Package Type NSC Package Drawing Supplied As LM5112-SD LLP-6 SDE06A 1000 shipped in Tape & Reel LM5112-SDX LLP-6 SDE06A 4500 shipped in Tape & Reel Pin Description Pin Name Description Application Information 1 IN Non-inverting input pin TTL compatible thresholds. Pull up to VCC when not used 2 VEE Power ground for driver outputs Connect to either power ground or a negative gate drive supply for positive or negative voltage swing 3 VCC Positive Supply voltage input Locally decouple to VEE. The decoupling capacitor should be located close to the chip 4 OUT Gate drive output Capable of sourcing 3A and sinking 7A. Voltage swing of this output is from VEE to VCC 5 IN_REF Ground reference for control inputs Connect to power ground (VEE) for standard positive only output voltage swing. Connect to system logic ground when VEE is connected to a negative gate drive supply 6 INB Inverting input pin TTL compatible thresholds. Connect to IN_REF when not used Exposed Pad Exposed Pad, underside of LLP package Internally bonded to the die substrate. Connect to VEE ground pin for low thermal impedance --- www.national.com 2 IN_REF to VEE If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Storage Temperature Range VCC to VEE −0.3V to 15V ESD Rating VCC to IN_REF −0.3V to 15V IN/INB to IN_REF −0.3V to 15V Electrical Characteristics −0.3V to 5V −55˚C to +150˚C Maximum Junction Temperature +150˚C Operating Junction Temperature −40˚C+125˚C 2kV TJ = −40˚C to +125˚C, VCC = 12V, INB = IN_REF = VEE = 0V, No Load on out- put, unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS 14 V 3.0 3.5 V SUPPLY VCC VCC operating range VCC – IN_REF and VCC - VEE 3.5 UVLO VCC Under-voltage lockout (rising) VCC – IN_REF 2.4 VCCH VCC Under-voltage hysteresis 230 ICC VCC supply current 1.0 2.0 mA 1.75 2.3 V mV CONTROL INPUTS VIH Logic High VIL Logic low HYS Input Hysteresis IIL Input Current Low IN = INB = 0V -1 0.1 1 µA IIH Input Current High IN = INB = VCC -1 0.1 1 µA 0.8 1.35 V 400 mV OUTPUT DRIVER ROH Output Resistance High IOUT = -10mA 30 50 Ω ROL Output Resistance Low IOUT = 10mA 1.4 2.5 Ω ISOURCE Peak Source Current OUT = VCC/2, 200ns pulsed current 3 A ISINK Peak Sink Current OUT = VCC/2, 200ns pulsed current 7 A SWITCHING CHARACTERISTICS td1 Propagation Delay Time Low to High, IN/ INB rising ( IN to OUT) CLOAD = 2 nF, see Figure 3 25 40 ns td2 Propagation Delay Time High to Low, IN / INB falling (IN to OUT) CLOAD = 2 nF, see Figure 3 25 40 ns tr Rise time CLOAD = 2 nF , see Figure 3 14 ns tf Fall time CLOAD = 2 nF , see Figure 3 12 ns TJ = 150˚C 500 mA LATCHUP PROTECTION AEC –Q100, METHOD 004 Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device is intended to be functional. For guaranteed specifications and test conditions, see the Electrical Characteristics. 3 www.national.com LM5112 Absolute Maximum Ratings (Note 1) LM5112 Timing Waveforms 20066805 20066804 (b) (a) FIGURE 1. (a) Inverting, (b) Non-Inverting www.national.com 4 LM5112 Typical Performance Characteristics Supply Current vs Frequency Supply Current vs Capacitive Load 20066808 20066807 Rise and Fall Time vs Supply Voltage Rise and Fall Time vs Temperature 20066809 20066810 Rise and Fall Time vs Capacitive Load Delay Time vs Supply Voltage 20066811 20066812 5 www.national.com LM5112 Typical Performance Characteristics (Continued) Delay Time vs Temperature RDSON vs Supply Voltage 20066813 20066814 UVLO Thresholds and Hysteresis vs Temperature Peak Current vs Supply Voltage 20066816 20066815 www.national.com 6 LM5112 20066803 FIGURE 2. Simplified Application Block Diagram When driving the MOSFET gates from a single positive supply, the IN_REF and VEE pins are both connected to the power ground. Detailed Operating Description The LM5112 is a high speed , high peak current (7A) single channel MOSFET driver. The high peak output current of the LM5112 will switch power MOSFET’s on and off with short rise and fall times, thereby reducing switching losses considerably. The LM5112 includes both inverting and noninverting inputs that give the user flexibility to drive the MOSFET with either active low or active high logic signals. The driver output stage consists of a compound structure with MOS and bipolar transistor operating in parallel to optimize current capability over a wide output voltage and operating temperature range. The bipolar device provides high peak current at the critical Miller plateau region of the MOSFET VGS , while the MOS device provides rail-to-rail output swing. The totem pole output drives the MOSFET gate between the gate drive supply voltage VCC and the power ground potential at the VEE pin. The control inputs of the driver are high impedance CMOS buffers with TTL compatible threshold voltages. The negative supply of the input buffer is connected to the input ground pin IN_REF. An internal level shifting circuit connects the logic input buffers to the totem pole output drivers. The level shift circuit and separate input/output ground pins provide the option of single supply or split supply configurations. The isolated input and output stage grounds provide the capability to drive the MOSFET to a negative VGS voltage for a more robust and reliable off state. In split supply configuration, the IN_REF pin is connected to the ground of the controller which drives the LM5112 inputs. The VEE pin is connected to a negative bias supply that can range from the IN_REF potential to as low as 14 V below the Vcc gate drive supply. For reliable operation, the maximum voltage difference between VCC and IN_REF or between VCC and VEE is 14V. The minimum recommended operating voltage between Vcc and IN_REF is 3.5V. An Under Voltage Lock Out (UVLO) circuit is included in the LM5112 which senses the voltage difference between VCC and the input ground pin, IN_REF. When the VCC to IN_REF voltage difference falls below 2.8V the driver is disabled and the output pin is held in the low state. The UVLO hysteresis prevents chattering during brown-out conditions; the driver will resume normal operation when the VCC to IN_REF differential voltage exceeds 3.0V. 7 www.national.com LM5112 Layout Considerations Attention must be given to board layout when using LM5112. Some important considerations include: 1. A Low ESR/ESL capacitor must be connected close to the IC and between the VCC and VEE pins to support high peak currents being drawn from VCC during turn-on of the MOSFET. 2. Proper grounding is crucial. The driver needs a very low impedance path for current return to ground avoiding inductive loops. Two paths for returning current to ground are a) between LM5112 IN_REF pin and the ground of the circuit that controls the driver inputs and b) between LM5112 VEE pin and the source of the power MOSFET being driven. Both paths should be as short as possible to reduce inductance and be as wide as possible to reduce resistance. These ground paths should be distinctly separate to avoid coupling between the high current output paths and the logic signals that drive the LM5112. With rise and fall times in the range of 10 to 30nsec, care is required to minimize the lengths of current carrying conductors to reduce their inductance and EMI from the high di/dt transients generated when driving large capacitive loads. 3. 20066806 FIGURE 3. The schematic above shows a conceptual diagram of the LM5112 output and MOSFET load. Q1 and Q2 are the switches within the gate driver. Rg is the gate resistance of the external MOSFET, and Cin is the equivalent gate capacitance of the MOSFET. The equivalent gate capacitance is a difficult parameter to measure as it is the combination of Cgs (gate to source capacitance) and Cgd (gate to drain capacitance). The Cgd is not a constant and varies with the drain voltage. The better way of quantifying gate capacitance is the gate charge Qg in coloumbs. Qg combines the charge required by Cgs and Cgd for a given gate drive voltage Vgate. The gate resistance Rg is usually very small and losses in it can be neglected. The total power dissipated in the MOSFET driver due to gate charge is approximated by: PDRIVER = VGATE x QG x FSW Where FSW = switching frequency of the MOSFET. If either channel is not being used, the respective input pin (IN or INB) should be connected to either VEE or VCC to avoid spurious output signals. Thermal Performance INTRODUCTION The primary goal of the thermal management is to maintain the integrated circuit (IC) junction temperature (Tj) below a specified limit to ensure reliable long term operation. The maximum TJ of IC components should be estimated in worst case operating conditions. The junction temperature can be calculated based on the power dissipated on the IC and the junction to ambient thermal resistance θJA for the IC package in the application board and environment. The θJA is not a given constant for the package and depends on the PCB design and the operating environment. For example, consider the MOSFET MTD6N15 whose gate charge specified as 30 nC for VGATE = 12V. Therefore, the power dissipation in the driver due to charging and discharging of MOSFET gate capacitances at switching frequency of 300 kHz and VGATE of 12V is equal to PDRIVER = 12V x 30 nC x 300 kHz = 0.108W. In addition to the above gate charge power dissipation, transient power is dissipated in the driver during output transitions. When either output of the LM5112 changes state, current will flow from VCC to VEE for a very brief interval of time through the output totem-pole N and P channel MOSFETs. The final component of power dissipation in the driver is the power associated with the quiescent bias current consumed by the driver input stage and Under-voltage lockout sections. Characterization of the LM5112 provides accurate estimates of the transient and quiescent power dissipation components. At 300 kHz switching frequency and 30 nC load used in the example, the transient power will be 8 mW. The 1 mA nominal quiescent current and 12V VGATE supply produce a 12 mW typical quiescent power. Therefore the total power dissipation PD = 0.118 + 0.008 + 0.012 = 0.138W. We know that the junction temperature is given by TJ = PD x θJA + TA Or the rise in temperature is given by TRISE = TJ − TA = PD x θJA DRIVE POWER REQUIREMENT CALCULATIONS IN LM5112 LM5112 is a single low side MOSFET driver capable of sourcing / sinking 3A / 7A peak currents for short intervals to drive a MOSFET without exceeding package power dissipation limits. High peak currents are required to switch the MOSFET gate very quickly for operation at high frequencies. www.national.com 8 exposed copper pad, which can readily dissipate heat to the surroundings, θJA as low as 40˚C / Watt is achievable with the package. The resulting Trise for the driver example above is thereby reduced to just 5.5 degrees. Therefore TRISE is equal to TRISE = 0.138 x 40 = 5.5˚C (Continued) For LLP-6 package, the integrated circuit die is attached to leadframe die pad which is soldered directly to the printed circuit board. This substantially decreases the junction to ambient thermal resistance (θJA). By providing suitable means of heat dispersion from the IC to the ambient through 9 www.national.com LM5112 Thermal Performance LM5112 Tiny 7A MOSFET Gate Driver Physical Dimensions inches (millimeters) unless otherwise noted 6-Lead LLP Package NS Package Number SDE06A National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560