MICROCIRCUIT DATA SHEET Original Creation Date: 10/30/95 Last Update Date: 08/24/98 Last Major Revision Date: 08/04/98 MN100328-X REV 2A0 LOW POWER OCTAL ECL/TTL BI-DIRECTIONAL TRANSLATOR WITH LATCH General Description The F100328 is an octal latch bi-directional translator designed to convert TTL logic levels to 100K ECL logic levels and vice versa. The direction of this translation is determined by the DIR input. A LOW on the output enable input (OE) holds the ECL outputs in a cut-off state and the TTL outputs at a high impedance level. A HIGH on the latch enable input (LE) latches the data at both inputs even though only one output is enabled at the time. A LOW on LE makes the F100328 transparent. The cut-off state is designed to be more negative than a normal ECL LOW level. This allows the output emitter-followers to turn off when the termination supply is -2.0V, presenting a high impedance to the data bus. This high inpedance reduces termination power and prevents loss of low state noise margin when several loads share the bus. The F100328 is designed with FAST TTL output buffers, featuring optimal DC drive and capable of quickly charging and discharging highly capacitive loads. All inputs have 50K ohm pull-down resistors. Industry Part Number NS Part Numbers 100328 100328DMQB 100328FMQB Prime Die F328 Processing Subgrp Description MIL-STD-883, Method 5004 1 2 3 4 5 6 7 8A 8B 9 10 11 Quality Conformance Inspection MIL-STD-883, Method 5005 1 Static tests at Static tests at Static tests at Dynamic tests at Dynamic tests at Dynamic tests at Functional tests at Functional tests at Functional tests at Switching tests at Switching tests at Switching tests at Temp ( oC) +25 +125 -55 +25 +125 -55 +25 +125 -55 +25 +125 -55 MICROCIRCUIT DATA SHEET MN100328-X REV 2A0 Features - Identical performance to the 100128 at 50% of the supply current Bi-directional translation 2000V ESD protection Latched outputs FAST TTL outputs TRI-STATE outputs Voltage compensated operating range= -4.2V to -5.7V Available to industrial grade temperature range Available to MIL-STD-883 2 MICROCIRCUIT DATA SHEET MN100328-X REV 2A0 (Absolute Maximum Ratings) (Note 1) Storage Temperature (Tstg) -65 C to +150 C Maximum Junction Temperature (Tj) Ceramic Plastic Vee Pin Potential to Ground Pin +175 C +150 C -7.0V to +0.5V Vttl Pin Potential to Ground Pin -0.5V to +6.0V ECL Input Voltage (DC) Vee to +0.5V ECL Output Current (DC Output HIGH) -50mA TTL Input Voltage (Note 3) -0.5V to +6.0V TTL Input Current (Note 3) -30mA to +5.0mA Voltage Applied to Output in HIGH State TRI-STATE Output -0.5V to +5.5V Current Applied to TTL Output in LOW State (Max) Twice the Rated Iol(mA) ESD (Note 2) > 2000V Note 1: Note 2: Note 3: Absolute maximum ratings are those values beyond which the device may be damaged or have its useful life impaired. Functional operation under these conditions is not implied. ESD testing conforms to MIL-STD-883, Method 3015. Either voltage limit or current limit is sufficient to protect inputs. Recommended Operating Conditions Case Temperature (Tc) Commercial Military Industrial ECL Supply Voltage (Vee) 0 C to +85 C -55 C to +125 C -40 C to +85 C -5.7V to -4.2V TTL Supply Voltage (Vttl) +4.5V to +5.5V 3 MICROCIRCUIT DATA SHEET MN100328-X REV 2A0 Electrical Characteristics DC PARAMETERS (The following conditions apply to all the following parameters, unless otherwise specified.) DC: Vee Range: -4.2V to -5.7V, VCC=VCCA=GND, Tc= -55 to +125, VTTL = +4.5V to +5.5V SYMBOL PARAMETER CONDITIONS NOTES PINNAME MIN MAX UNIT SUBGROUPS IIH(1) Input HIGH Current VEE=-4.7V, VTTL=5.5V, VM=2.7V 1, 3 Tn 70 uA 1, 2, 3 IBVI Input Breakdown Current VEE=-4.7V, VTTL=5.5V, VM=5.5V 1, 3 Tn 1.0 mA 1, 2, 3 IIL(1) Input Low Current VEE=-4.5V, VTTL=5.5V, VM=0.5V 1, 3 Tn -1.0 mA 1, 2, 3 VFCD Input Clamp Diode Voltage VEE=-4.5V, VTTL=4.5V, IM=-18mA 1, 3 Tn -1.2 V 1, 2, 3 VOH(1) Output HIGH Voltage VEE=-4.2V/-5.7V, VTTL=4.5/5.5V, VIH=3.0V, VIL=0.0V, LOADING: 50 ohms to -2.0V 1, 3 En -1025 -870 mV 1, 2 1, 3 En -1085 -870 mV 3 Vee=-4.2V/-5.7V, VTTL=4.5V/5.5V, VIH=3.0V, VIL=0.0V OE=DIR=-0.87 LOADING: 50 Ohms to -2.0V 1, 3 En -1830 -1620 mV 1, 2 1, 3 En -1830 -1555 mV 3 Vee=-4.2V/-5.7V, VTTL=4.5V/5.5V, VIH=3.0V, VIL=0.0V OE=-1.83 LOADING: 50 Ohms to -2.0V 1, 3 En(CUTO FF VOLTAGE ) -1950 mV 1, 2 1, 3 En(CUTO FF VOLTAGE ) -1850 mV 3 VOL(1) VOHC VOLC Output LOW Voltage Output HIGH Voltage Corner Point High Vee=-4.2V/-5.7V, VTTL=4.5V/5.5V, VIH=2.0V, VIL=0.8V LOADING: 50 Ohms TO -2.0V 1, 3 En -1035 mV 1, 2 1, 3 En -1085 mV 3 Output LOW Voltage Corner Point High Vee=-4.2V/-5.7V, VTTL=4.5V/5.5V, VIH=2.0V, VIL=0.8V OE=DIR=-1.165V LOADING: 50 Ohms To -2.0V 1, 3 En -1610 mV 1, 2 1, 3 En -1555 mV 3 Vee=-4.2V/-5.7V, VTTL=4.5V/5.5V, VIH=5.0V, VIL=0.0V OE=-1.475V LOADING: 50 Ohms to -2.0V 1, 3 En(CUTO FF VOLTAGE ) -1950 mV 1, 2 1, 3 En(CUTO FF VOLTAGE ) -1850 mV 3 V 1, 2, 3 0.8 V 1, 2, 3 VIH(1) Input HIGH Voltage 1, Tn 3, 7 VIL(1) Input LOW Voltage 1, Tn 3, 7 IEE Power Supply Current 2.0 VEE=-4.2/-4.8V, VTTL=5.0V 1, 3 VEE -165 -73 mA 1, 2, 3 VEE=-5.7V, VTTL=5.0V 1, 3 VEE -175 -73 mA 1, 2, 3 4 MICROCIRCUIT DATA SHEET MN100328-X REV 2A0 Electrical Characteristics DC PARAMETERS(Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) DC: Vee Range: -4.2V to -5.7V, VCC=VCCA=GND, Tc= -55 to +125, VTTL = +4.5V to +5.5V SYMBOL IIH(2) PARAMETER Input High Current CONDITIONS NOTES VEE=-5.7V, VTTL=5.0V, VM=-0.87V PINNAME MIN MAX UNIT SUBGROUPS 1, 3 INPUTS 350 uA 1, 2 1, 3 INPUTS 500 uA 3 IIL(2) Input LOW Current VEE=-4.2V, VTTL=5.0V, VM=-1.83V 1, 3 INPUTS 0.5 uA 1, 2, 3 VOH(2) Output HIGH Voltage VEE=-4.2V/-5.7V, VTTL=4.5V, VIH=-1.165V, VIL=-1.475V, IOH=-1.0MA 1, 3 Tn 2.5 V 1, 2 1, 3 Tn 2.4 V 3 VEE=-4.2V/-5.7V, VTTL=4.5V, VIH=-1.165V, VIL=-1.475V, IOH=-3.0MA 1, 3 Tn 2.4 V 1, 2 0.5 V 1, 2, 3 -150 mA 1, 2, 3 VOL(2) Output LOW Voltage VEE=-4.2V/-5.7V, VTTL=4.5V, VIH=-1.165V, VIL=-1.475V, IOL=24.0MA 1, 3 Tn IOS Short-Circuit Current VEE=-4.5V, VTTL=5.5V, VM=0.0V 1, 3 Tn IOZHT TRI-STATE Current Output HIGH VEE=-4.5V, VTTL=5.5V, VM=2.7V 1, 3 Tn 70 uA 1, 2, 3 IOZLT TRI-STATE Current Output HIGH VEE=-4.5V, VTTL=5.5V, VM=0.5V 1, 3 Tn -1.0 mA 1, 2, 3 VIH(2) Input HIGH Voltage 1, INPUTS 3, 7 -1165 -870 mV 1, 2, 3 VIL(2) Input LOW Voltage 1, INPUTS 3, 7 -1830 -1475 mV 1, 2, 3 ITTLL Supply Current VEE=-4.5V, VTTL=5.5V 1, 3 VTTL 75 mA 1, 2, 3 ITTLH Supply Current VEE=-4.5V, VTTL=5.5V 1, 3 VTTL 50 mA 1, 2, 3 ITTLZ Supply Current VEE=-4.5V, VTTL=5.5V 1, 3 VTTL 70 mA 1, 2, 3 -60 AC PARAMETERS (The following conditions apply to all the following parameters, unless otherwise specified.) AC: VEE Range: -4.2V to -5.7V, VTTL Range: 4.5V to 5.5V, VCC=VCCA=GND, ECL outputs loaded 50 ohms to -2.0V, TTL outputs loaded RL= 500 ohms and CL= 50pF. tpLH/tpHL( 1) Propagation Delay VEE=-4.2/-5.7V VTTL=4.5/5.5V 5 2, 4 Tn to En 1.1 3.6 ns 9 2, 4 Tn to En 0.8 3.7 ns 10 2, 4 Tn to En 0.8 3.4 ns 11 MICROCIRCUIT DATA SHEET MN100328-X REV 2A0 Electrical Characteristics AC PARAMETERS(Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) AC: VEE Range: -4.2V to -5.7V, VTTL Range: 4.5V to 5.5V, VCC=VCCA=GND, ECL outputs loaded 50 ohms to -2.0V, TTL outputs loaded RL= 500 ohms and CL= 50pF. SYMBOL PARAMETER tpLH/tpHL( 2) Propagation Delay tPZH(1) tPHZ(1) tPHZ(2) tS(1) tH(1) tPW(1) tTLH/tTHL Enable Time Disable Time Disable Time Setup Time Hold Time Pulse Width Transition Time CONDITIONS NOTES VEE=-4.2/-5.7V VTTL=4.5/5.5V VEE=-4.2/-5.7V VTTL=4.5/5.5V VEE=-4.2/-5.7V VTTL=4.5/5.5V VEE=-4.2/-5.7V VTTL=4.5/5.5V VEE=-4.2/-5.7V VTTL=4.5/5.5V VEE=-4.2/-5.7V VTTL=4.5/5.5V VEE=-4.2/-5.7V VTTL=4.5/5.5V VEE=-4.2/-5.7V VTTL=4.5/5.5V 6 PINNAME MIN MAX UNIT SUBGROUPS 2, 4 LE to En 1.4 3.7 ns 9 2, 4 LE to En 1.1 3.8 ns 10 2, 4 LE to En 1.2 3.8 ns 11 2, 4 0E to En 1.5 4.0 ns 9 2, 4 0E to En 2.0 5.2 ns 10 2, 4 0E to En 0.8 3.6 ns 11 2, 4 0E to En 1.6 4.2 ns 9 2, 4 0E to En 1.6 4.3 ns 10 2, 4 0E to En 1.5 4.6 ns 11 2, 4 DIR to En 1.6 4.3 ns 9 2, 4 DIR to En 1.7 4.3 ns 10 2, 4 DIR to En 1.6 4.7 ns 11 6 Tn to LE 2.0 ns 9 6 Tn to LE 2.5 ns 10, 11 6 Tn to LE 2.0 ns 9 6 Tn to LE 2.5 ns 10, 11 6 LE 2.0 ns 9 6 LE 2.5 ns 10, 11 6 En 0.5 2.1 ns 9 6 En 0.4 2.4 ns 10 6 En 0.4 2.3 ns 11 MICROCIRCUIT DATA SHEET MN100328-X REV 2A0 Electrical Characteristics AC PARAMETERS(Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) AC: VEE Range: -4.2V to -5.7V, VTTL Range: 4.5V to 5.5V, VCC=VCCA=GND, ECL outputs loaded 50 ohms to -2.0V, TTL outputs loaded RL= 500 ohms and CL= 50pF. SYMBOL PARAMETER tPLH/tPHL( 3) Propagation Delay tPLH/tPHL( 4) tPZH(3) tPZL(3) tPHZ(4) tPLZ(4) tPHZ(5) Propagation Delay Enable Time Enable Time Disable Time Disable Time Disable Time CONDITIONS NOTES VEE=-4.2/-5.7V VTTL=4.5/5.5V VEE=-4.2/-5.7V VTTL=4.5/5.5V VEE=-4.2/-5.7V VTTL=4.5/5.5V VEE=-4.2/-5.7V VTTL=4.5/5.5V VEE=-4.2/-5.7V VTTL=4.5/5.5V VEE=-4.2/-5.7V VTTL=4.5/5.5V VEE=-4.2/-5.7V VTTL=4.5/5.5V 7 PINNAME MIN MAX UNIT SUBGROUPS 2, 4 En to Tn 2.0 5.6 ns 9 2, 4 En to Tn 2.2 6.3 ns 10 2, 4 En to Tn 2.1 6.0 ns 11 2, 4 LE to Tn 3.1 6.5 ns 9 2, 4 LE to Tn 3.3 7.5 ns 10 2, 4 LE to Tn 3.1 7.0 ns 11 2, 4 OE to Tn 3.7 8.0 ns 9 2, 4 OE to Tn 4.0 9.2 ns 10 2, 4 OE to Tn 3.2 8.0 ns 11 2, 4 OE to Tn 4.0 8.5 ns 9 2, 4 OE to Tn 4.3 9.6 ns 10 2, 4 OE to Tn 3.6 8.0 ns 11 2, 4 OE to Tn 3.3 8.0 ns 9 2, 4 OE to Tn 3.5 8.4 ns 10 2, 4 OE to Tn 3.2 8.5 ns 11 2, 4 OE to Tn 3.4 7.5 ns 9 2, 4 OE to Tn 4.1 10.0 ns 10 2, 4 OE to Tn 3.0 8.0 ns 11 2, 4 DIR to Tn 2.6 7.0 ns 9, 11 2, 4 DIR to Tn 2.9 8.0 ns 10 MICROCIRCUIT DATA SHEET MN100328-X REV 2A0 Electrical Characteristics AC PARAMETERS(Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) AC: VEE Range: -4.2V to -5.7V, VTTL Range: 4.5V to 5.5V, VCC=VCCA=GND, ECL outputs loaded 50 ohms to -2.0V, TTL outputs loaded RL= 500 ohms and CL= 50pF. SYMBOL tPLZ(5) tS(2) tH(2) tPW(2) PARAMETER Disable Time Setup Time Hold Time Pulse Width Note 1: Note 2: Note 3: Note 4: Note 5: Note 6: Note 7: CONDITIONS NOTES VEE=-4.2/-5.7V VTTL=4.5/5.5V VEE=-4.5/-5.7V VTTL=4.5/5.5V VEE=-4.5/-5.7V VTTL=4.5/5.5V VEE=-4.5/-5.7V VTTL=4.5/5.5V PINNAME MIN MAX UNIT 2, 4 DIR to Tn 3.1 7.0 ns 9 2, 4 DIR to Tn 4.0 10.0 ns 10 2, 4 DIR to Tn 2.7 7.0 ns 11 6 En to LE 2.0 ns 9 6 En to LE 2.5 ns 10, 11 6 En to LE 2.5 ns 9 6 En to LE 3.0 ns 10, 11 6 LE 2.0 ns 9 6 LE 5.0 ns 10 6 LE 2.5 ns 11 Screen tested 100% on each device at -55 C, +25 C and +125 C temp., subgroups 1, 2, 3, 7 & 8. Screen tested 100% on each device at +25 C temp only, subgroup A9. Sample tested (Method 5005, Table 1) on each MFG. lot at +25 C, +125 C & -55 C temp., subgroups A1, 2, 3, 7 & 8. Sample tested (Method 5005, Table 1) on each MFG. lot at +25 C, subgroup A9, and at +125 C & -55 C temp., subgroups A10 & 11. Sample tested (Method 5005, Table 1) on each MFG. lot at +25 C temp. only, subgroup A9. Not tested at +25 C, +125 C & -55 C temp. (DESIGN CHARACTERIZATION DATA). Guaranteed by applying specified input condition and testing VOH/VOL. 8 SUBGROUPS MICROCIRCUIT DATA SHEET MN100328-X REV 2A0 Graphics and Diagrams GRAPHICS# DESCRIPTION J24ERJ CERDIP (J), 24LD, .400 CENTERS (P/P DWG) P000056A CERDIP (J), 24LD .400 CENTERS (PIN OUT) P000057A CERPACK, QUAD, W24BRE CERPACK, QUAD, 24 LEAD (P/P DWG) 24 LEAD (PIN OUT) See attached graphics following this page. 9 MICROCIRCUIT DATA SHEET MN100328-X REV 2A0 Revision History Rev ECN # 2A0 M0002980 08/24/98 Rel Date Originator Changes Donald B. Miller 1) Change page 6, tpHZ(2) subgroup 11 minimum spec from 1.4 ns to 1.6 ns. 2) Change page 7, tpHZ(5) subgroup 11 minimum spec from 2.9 ns to 2.6 ns and the maximum spec from 8.0 ns to 7.0 ns. 10