MICROCIRCUIT DATA SHEET Original Creation Date: 01/06/99 Last Update Date: 04/05/99 Last Major Revision Date: 04/01/99 MNCLC432A-X REV 0A0 DUAL WIDEBAND MONOLITHIC OP AMP General Description The CLC432 is a current-feedback amplifier that provides a wide bandwidth and high slew rate for applications where board density and power are key considerations. This amplifier provides a dc-coupled small signal bandwidth exceeding 92MHz while consuming only 7mA per channel. Operating from +15V supplies, the CLC432's enhanced slew rate circuitry delivers large-signal bandwidths with output voltage swings up to 28Vpp. A wide range of bandwidth-insensitive gains are made possible by virtue of the CLC432's current-feedback topology. The large common-mode input range and fast settling time (70ns to 0.05%) makes this amplifier well suited for CCD & data telecommunication applications. Many high performance video applications requiring signal gain and/or switching will be satisfied with the CLC432 due to it's very low differential gain and phase errors (less than 0.1% and 0.1 degrees; Av = +2V/V at 4.43MHz into 150Ohms load). Quick 8ns rise and fall times on 10V pulses allow the CLC432 to drive either twisted pair or coaxial transmission lines over long distances. The CLC432's combination of low input voltage noise, wide common-mode input voltage range and large output voltage swings makes it especially well suited for wide dynamic range signal processing applications. Industry Part Number NS Part Numbers CLC432A CLC432AJ-QML Prime Die LB1792A Controlling Document 5962-9472502MPA Processing Subgrp Description 1 2 3 4 5 6 7 8A 8B 9 10 11 MIL-STD-883, Method 5004 Quality Conformance Inspection MIL-STD-883, Method 5005 1 Static tests at Static tests at Static tests at Dynamic tests at Dynamic tests at Dynamic tests at Functional tests at Functional tests at Functional tests at Switching tests at Switching tests at Switching tests at Temp ( oC) +25 +125 -55 +25 +125 -55 +25 +125 -55 +25 +125 -55 MICROCIRCUIT DATA SHEET MNCLC432A-X REV 0A0 Features - Wide bandwidth: 92Mhz (Av = +1) 62MHz (Av = +2) Fast slew rate: 2000V/us Fast disable: 1us to high-Z output High channel isolation: 70dB at 10MHz Single or dual supplies: +5V to +16.5V Applications - Video signal multiplexing Twisted-pair differential driver CCD buffer & level shifting Discrete gain-select amplifier Transimpedance amplifier 2 MICROCIRCUIT DATA SHEET MNCLC432A-X REV 0A0 (Absolute Maximum Ratings) (Note 1) Supply Voltage (Vs) +16.5 V dc Output Current (Iout) 100mA Common Mode Input Voltage (Vcm) +Vs Differential Input Voltage(Vid) +10 V Maximum Power Dissipation (Pd) (Note 2) 1.02W Lead Temperature (Soldering, 10 seconds) Junction Temperature (Tj) +300 C +175 C Storage Temperature Range -65 C to +150 C Thermal Resistance Junction -to-ambient (ThetaJA) Ceramic DIP (Still Air) (500 LFPM) Junction -to-case (ThetaJC) Ceramic DIP Package Weight (Typical) Ceramic DIP ESD Tolerance (Note 3) ESD Ratings Note 1: Note 2: Note 3: 128 C/W 67 C/W 23 C/W TBD 2000 V Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. The maximum package power dissipation must be derated at elevated temperatures and is dictated by Tjmax (maximum junction temperature), ThetaJA (package junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable package power dissipation at any temperature is Pdmax = (Tjmax -TA) / ThetaJA or the number given in the Absolute Maximum Ratings, whichever is lower. Human body model, 100 pF discharged through 1.5K Ohms. 3 MICROCIRCUIT DATA SHEET MNCLC432A-X REV 0A0 Recommended Operating Conditions Supply Voltage (Vs) +15V dc Gain Range (Av) +1 V/V to +10 V/V Ambient Operating Temperature Range (TA) -55 C to +125 C 4 MICROCIRCUIT DATA SHEET MNCLC432A-X REV 0A0 Electrical Characteristics DC PARAMETERS: Static and DC Tests (The following conditions apply to all the following parameters, unless otherwise specified.) DC: Vs = +15V dc, Av = +2, and load resistance (Rl) = 100Ohms. Gain Resistance (Rg) and Feedback resistance (Rf) equals 750Ohms. -55 C < Ta < +125 C (Note 3). SYMBOL Ibn Ibi Vio PARAMETER CONDITIONS NOTES PINNAME MIN MAX UNIT SUBGROUPS Input Bias Current, noninverting -8 +8 uA 1, 2 -18 +18 uA 3 Input Bias Current, inverting -6 6 uA 1, 2 -9 9 uA 3 Input Offset Voltage -6 6 mV 1, 3 -9 9 mV 2 Dibn Average Input Bias Current Drift, noninverting Ta = +125 C, -55 C 1 -150 150 nA/C 2, 3 Dibi Average Input Bias Current Drift, inverting Ta = +125 C, -55 C 1 -40 40 nA/C 2, 3 Dvio Average Input Offset Voltage Drift Ta = +125 C, -55 C 1 -50 50 uV/C 2, 3 Icc Supply Current No Load 15.8 mA 1, 2 19.6 mA 3 59 dB 4, 6 57 dB 5 1 58 dB 4 1 56 dB 5, 6 PSRR CMRR Power Supply Rejection Ratio Common Mode Rejection Ratio +Vs = +4.0V to +5.0V, -Vs = -4.0V to -5.0V Vcm = +1V 5 MICROCIRCUIT DATA SHEET MNCLC432A-X REV 0A0 Electrical Characteristics AC PARAMETERS: Frequency Domain Tests (The following conditions apply to all the following parameters, unless otherwise specified.) AC: Vs = +15V dc, Av = +2, and load resistance (Rl) = 100Ohms. Gain Resistance (Rg) and Feedback resistance (Rf) equals 750Ohms. -55 C < Ta < +125 C (Note 3). SYMBOL SSBW LSBW GFPH PARAMETER Small Signal Bandwidth Large Signal Bandwidth Gain Flatness Peaking High CONDITIONS NOTES -3 dB bandwidth, Vout < 4.0 Vpp -3 dB bandwidth, Vout < 10 Vpp PINNAME MIN Gain Flatness Rolloff DP LPD Differential Gain 4 2 34 MHz 5 2 42 MHz 6 1 21 MHz 4, 6 1 17 MHz 5 0.5 dB 4 0.9 dB 5, 6 0.8 dB 4 0.8 dB 5, 6 0.1 MHz to 100 MHz, Vout < 4.0 Vpp 0.1 MHz to 20 MHz, Vout < 4.0 Vpp Differential Phase Linear Phase Deviation 4.43 MHz 4.43 MHz DC to 20MHz, Vout < 4.0 Vpp 6 SUBGROUPS MHz 2 DG UNIT 42 2 GFR MAX 1 0.18 % 4, 6 1 0.22 % 5 1 0.18 Deg. 4, 6 1 0.32 Deg. 5 1 1.8 Deg. 4, 6 1 2.3 Deg. 5 MICROCIRCUIT DATA SHEET MNCLC432A-X REV 0A0 Electrical Characteristics AC PARAMETERS: Distortion and Noise Tests (The following conditions apply to all the following parameters, unless otherwise specified.) AC: Vs = +15V dc, Av = +2, and load resistance (Rl) = 100Ohms. Gain Resistance (Rg) and Feedback resistance (Rf) equals 750Ohms. -55 C < Ta < +125 C (Note 3). SYMBOL HD2 PARAMETER 2nd Harmonic Distortion HD3 3rd Harmonic Distortion VN Input Noise Voltage -ICN Inverting Input Noise Current +ICN Noninverting Input Noise Current CONDITIONS NOTES PINNAME MIN 2 Vpp at 10 MHz > 1 MHz > 1 MHz UNIT SUBGROUPS 38 dBc 4 2 33 dBc 5 2 38 dBc 6 48 dBc 4 2 48 dBc 5, 6 1 4.2 nV/Sq 4, 6 1 4.7 RtHz nV/Sq 5 1 16 RtHz pA/Sq 4, 5 1 18 RtHz pA/Sq 6 1 2.5 RtHz pA/Sq 4 1 2.8 RtHz pA/Sq 5, 6 2 Vpp at 10 MHz > 1 MHz MAX RtHz AC PARAMETERS: Timing Tests (The following conditions apply to all the following parameters, unless otherwise specified.) AC: Vs = +15V dc, Av = +2, and load resistance (Rl) = 100Ohms. Gain Resistance (Rg) and Feedback resistance (Rf) equals 750Ohms. -55 C < Ta < +125 C (Note 3). SR Tr, Ts OS Slew Rate Tf Rise and Fall Time Settling Time Overshoot Vout = +10 V Step 10 V Step 2V step at 0.05% of the fixed value 2 V Step, 1 ns rise/fall 7 1 1500 V/uS 9 1 1400 V/uS 10, 11 1 12 nS 9, 11 1 14 nS 10 1 100 nS 9, 11 1 120 nS 10 1 10 % 9, 11 1 14 % 10 MICROCIRCUIT DATA SHEET MNCLC432A-X REV 0A0 Electrical Characteristics DC PARAMETERS: Perfomance Tests (The following conditions apply to all the following parameters, unless otherwise specified.) DC: Vs = +15V dc, Av = +2, and load resistance (Rl) = 100Ohms. Gain Resistance (Rg) and Feedback resistance (Rf) equals 750Ohms. -55 C < Ta < +125 C (Note 3). SYMBOL R+in PARAMETER Positive Input Capacitance Vout Output Voltage Range CMIR Iout NOTES Positive Input Resistance C+in Voutl CONDITIONS Output Voltage Range No Load Rl = 100Ohms Common Mode Input Voltage Range Output Current PINNAME MIN MAX UNIT SUBGROUPS 1 16 MOhms 4, 5 1 5 MOhms 6 1 1 pF 4, 5, 6 1 -13.6 +13.6 V 1, 2 1 -13.2 +13.2 V 3 1 -3.7 +3.7 V 1, 2 1 -2.7 +2.7 V 3 1 12 V 1, 2 1 11.5 V 3 1 38 mA 1, 2 1 28 mA 3 AC PARAMETERS: Switching Tests (The following conditions apply to all the following parameters, unless otherwise specified.) AC: Vs = +15V dc, Av = +2, and load resistance (Rl) = 100Ohms. Gain Resistance (Rg) and Feedback resistance (Rf) equals 750Ohms. -55 C < Ta < +125 C (Note 3). Ton Toff Switching turn on time Switching turn off time Vin = 4 Vpp at 10 MHz Vin = 4 Vpp at 10 MHz 1 150 uS 9, 10 1 170 uS 11 1 1000 uS 9, 11 1 1400 uS 10 2 V 1, 2, 3 V 1, 2, 3 Vih Disable Logic High Input Voltage Single ended mode 1 Vil Disable Logic Low Input Voltage Single ended mode 1 Idin Disable Logic Maximum Input Current DIS = Vil to Vih 1 180 uA 1, 2 1 210 uA 3 Minimum Differential Voltage DIS = Vil to Vih 1 0.4 V 1, 2 1 0.5 V 3 Vmin 8 0.8 MICROCIRCUIT DATA SHEET MNCLC432A-X REV 0A0 Electrical Characteristics AC PARAMETERS: Isolation Tests (The following conditions apply to all the following parameters, unless otherwise specified.) AC: Vs = +15V dc, Av = +2, and load resistance (Rl) = 100Ohms. Gain Resistance (Rg) and Feedback resistance (Rf) equals 750Ohms. -55 C < Ta < +125 C (Note 3). SYMBOL PARAMETER CONDITIONS NOTES PINNAME MIN MAX UNIT SUBGROUPS XTLK Crosstalk, input referred isolation 10 MHz 1 64 dB 4, 5, 6 ISO Off Isolation 10 MHz 1 53 dB 4, 5, 6 Note 1: Note 2: Note 3: If not tested, shall be guaranteed to the limits specified in table I Group A testing only. The algebraic convention, whereby the most negative value is a minimum and most positive is a maximum, is used in this table. Negative current shall be defined as convential current flow out of a device terminal. 9 MICROCIRCUIT DATA SHEET MNCLC432A-X REV 0A0 Graphics and Diagrams GRAPHICS# DESCRIPTION 07082HRA2 CERDIP (J), 8 LEAD (B/I CKT) J08ARL CERDIP (J), 8 LEAD (P/P DWG) P000405A CERDIP (J), 8 LEAD (PINOUT) See attached graphics following this page. 10 VOUT1 1 8 +VCC VINV1 2 7 VOUT2 VNON-INV1 3 6 VINV2 -VCC 4 5 VNON-INV2 CLC432J 8 - LEAD DIP CONNECTION DIAGRAM TOP VIEW P000405A N MIL/AEROSPACE OPERATIONS 2900 SEMICONDUCTOR DRIVE SANTA CLARA, CA 95050 MICROCIRCUIT DATA SHEET MNCLC432A-X REV 0A0 Revision History Rev ECN # 0A0 M0003352 04/05/99 Rel Date Originator Changes Shaw Mead Initial MDS Release 11