BSS123LT1 Preferred Device Power MOSFET 170 mAmps, 100 Volts N–Channel SOT–23 MAXIMUM RATINGS Rating Symbol Value Unit Drain–Source Voltage VDSS 100 Vdc Gate–Source Voltage – Continuous – Non–repetitive (tp ≤ 50 µs) VGS VGSM ±20 ±40 Vdc Vpk ID IDM 0.17 0.68 Symbol Max Unit PD 225 mW 1.8 mW/°C 556 °C/W Drain Current Continuous (Note 1.) Pulsed (Note 2.) http://onsemi.com 170 mAMPS 100 VOLTS RDS(on) = 6 N–Channel 3 Adc THERMAL CHARACTERISTICS Characteristic Total Device Dissipation FR–5 Board (Note 3.) TA = 25°C Derate above 25°C Thermal Resistance, Junction to Ambient RJA TJ, Tstg –55 to +150 °C 1. The Power Dissipation of the package may result in a lower continuous drain current. 2. Pulse Width 300 s, Duty Cycle 2.0%. 3. FR–5 = 1.0 0.75 0.062 in. 1 2 MARKING DIAGRAM Junction and Storage Temperature 3 SOT–23 CASE 318 STYLE 21 1 SA W 2 SA W = Device Code = Work Week PIN ASSIGNMENT Drain 3 1 2 Source Gate ORDERING INFORMATION Device Package Shipping BSS123LT1 SOT–23 3000 Tape & Reel BSS123LT3 SOT–23 10,000 Tape & Reel Preferred devices are recommended choices for future use and best overall value. Semiconductor Components Industries, LLC, 2001 February, 2001 – Rev. 3 1 Publication Order Number: BSS123LT1/D BSS123LT1 ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted) Characteristic Symbol Min Typ Max Unit V(BR)DSS 100 – – Vdc – – – – 15 60 OFF CHARACTERISTICS Drain–Source Breakdown Voltage (VGS = 0, ID = 250 µAdc) µAdc Zero Gate Voltage Drain Current (VGS = 0, VDS = 100 Vdc) TJ = 25°C TJ = 125°C IDSS Gate–Body Leakage Current (VGS = 20 Vdc, VDS = 0) IGSS – – 50 nAdc Gate Threshold Voltage (VDS = VGS, ID = 1.0 mAdc) VGS(th) 0.8 – 2.8 Vdc Static Drain–Source On–Resistance (VGS = 10 Vdc, ID = 100 mAdc) rDS(on) – 5.0 6.0 Ω gfs 80 – – mmhos Input Capacitance (VDS = 25 Vdc, VGS = 0, f = 1.0 MHz) Ciss – 20 – pF Output Capacitance (VDS = 25 Vdc, VGS = 0, f = 1.0 MHz) Coss – 9.0 – pF Reverse Transfer Capacitance (VDS = 25 Vdc, VGS = 0, f = 1.0 MHz) Crss – 4.0 – pF td(on) – 20 – ns td(off) – 40 – ns VSD – – 1.3 V ON CHARACTERISTICS (Note 4.) Forward Transconductance (VDS = 25 Vdc, ID = 100 mAdc) DYNAMIC CHARACTERISTICS SWITCHING CHARACTERISTICS(4) Turn–On Delay Time Turn–Off Delay Time (VCC = 30 Vdc, IC = 0.28 Adc, VGS = 10 Vdc, RGS = 50 Ω) REVERSE DIODE Diode Forward On–Voltage (ID = 0.34 Adc, VGS = 0 Vdc) 4. Pulse Test: Pulse Width 300 s, Duty Cycle 2.0%. http://onsemi.com 2 BSS123LT1 TYPICAL ELECTRICAL CHARACTERISTICS 2.0 1.0 VDS = 10 V TA = 25°C 1.6 VGS = 10 V 1.4 9V 1.2 8V 1.0 7V 0.8 6V 0.6 0.4 5V 0.2 4V 3V 0 I D, DRAIN CURRENT (AMPS) I D, DRAIN CURRENT (AMPS) 1.8 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 VDS, DRAN SOURCE VOLTAGE (VOLTS) 9.0 0.8 125°C 0.6 0.4 0.2 10 0 2.4 2.2 1.8 VGS = 10 V ID = 200 mA 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -60 -20 +20 +60 T, TEMPERATURE (°C) 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 VGS, GATE SOURCE VOLTAGE (VOLTS) 9.0 10 Figure 2. Transfer Characteristics VGS(th) , THRESHOLD VOLTAGE (NORMALIZED) r DS(on) , STATIC DRAIN-SOURCE ON-RESISTANCE (NORMALIZED) Figure 1. Ohmic Region 2.0 25°C -55°C +100 +140 1.2 1.05 VDS = VGS ID = 1.0 mA 1.1 1.10 1.0 0.95 0.9 0.85 0.8 0.75 0.7 -60 Figure 3. Temperature versus Static Drain–Source On–Resistance -20 +20 +60 T, TEMPERATURE (°C) +100 Figure 4. Temperature versus Gate Threshold Voltage http://onsemi.com 3 +140 BSS123LT1 INFORMATION FOR USING THE SOT–23 SURFACE MOUNT PACKAGE MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor packages must be the correct size to insure proper solder connection interface between the board and the package. With the correct pad geometry, the packages will self align when subjected to a solder reflow process. 0.037 0.95 0.037 0.95 0.079 2.0 0.035 0.9 0.031 0.8 inches mm SOT–23 one can calculate the power dissipation of the device which in this case is 225 milliwatts. The power dissipation of the SOT–23 is a function of the pad size. This can vary from the minimum pad size for soldering to a pad size given for maximum power dissipation. Power dissipation for a surface mount device is determined by TJ(max), the maximum rated junction temperature of the die, RθJA, the thermal resistance from the device junction to ambient, and the operating temperature, TA. Using the values provided on the data sheet for the SOT–23 package, PD can be calculated as follows: PD = PD = 150°C – 25°C 556°C/W = 225 milliwatts The 556°C/W for the SOT–23 package assumes the use of the recommended footprint on a glass epoxy printed circuit board to achieve a power dissipation of 225 milliwatts. There are other alternatives to achieving higher power dissipation from the SOT–23 package. Another alternative would be to use a ceramic substrate or an aluminum core board such as Thermal Clad. Using a board material such as Thermal Clad, an aluminum core board, the power dissipation can be doubled using the same footprint. TJ(max) – TA RθJA The values for the equation are found in the maximum ratings table on the data sheet. Substituting these values into the equation for an ambient temperature TA of 25°C, SOLDERING PRECAUTIONS • The soldering temperature and time shall not exceed 260°C for more than 10 seconds. • When shifting from preheating to soldering, the maximum temperature gradient shall be 5°C or less. • After soldering has been completed, the device should be allowed to cool naturally for at least three minutes. Gradual cooling should be used as the use of forced cooling will increase the temperature gradient and result in latent failure due to mechanical stress. • Mechanical stress or shock should not be applied during cooling. The melting temperature of solder is higher than the rated temperature of the device. When the entire device is heated to a high temperature, failure to complete soldering within a short time could result in device failure. Therefore, the following items should always be observed in order to minimize the thermal stress to which the devices are subjected. • Always preheat the device. • The delta temperature between the preheat and soldering should be 100°C or less.* • When preheating and soldering, the temperature of the leads and the case must not exceed the maximum temperature ratings as shown on the data sheet. When using infrared heating with the reflow soldering method, the difference shall be a maximum of 10°C. * Soldering a device without preheating can cause excessive thermal shock and stress which can result in damage to the device. http://onsemi.com 4 BSS123LT1 PACKAGE DIMENSIONS SOT–23 (TO–236) CASE 318–08 ISSUE AF NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. A L 3 1 V B S 2 G C D H J K DIM A B C D G H J K L S V INCHES MIN MAX 0.1102 0.1197 0.0472 0.0551 0.0350 0.0440 0.0150 0.0200 0.0701 0.0807 0.0005 0.0040 0.0034 0.0070 0.0140 0.0285 0.0350 0.0401 0.0830 0.1039 0.0177 0.0236 STYLE 21: PIN 1. GATE 2. SOURCE 3. DRAIN http://onsemi.com 5 MILLIMETERS MIN MAX 2.80 3.04 1.20 1.40 0.89 1.11 0.37 0.50 1.78 2.04 0.013 0.100 0.085 0.177 0.35 0.69 0.89 1.02 2.10 2.64 0.45 0.60 BSS123LT1 Notes http://onsemi.com 6 BSS123LT1 Notes http://onsemi.com 7 BSS123LT1 Thermal Clad is a registered trademark of the Bergquist Company. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION NORTH AMERICA Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada Email: [email protected] Fax Response Line: 303–675–2167 or 800–344–3810 Toll Free USA/Canada N. American Technical Support: 800–282–9855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor – European Support German Phone: (+1) 303–308–7140 (Mon–Fri 2:30pm to 7:00pm CET) Email: ONlit–[email protected] French Phone: (+1) 303–308–7141 (Mon–Fri 2:00pm to 7:00pm CET) Email: ONlit–[email protected] English Phone: (+1) 303–308–7142 (Mon–Fri 12:00pm to 5:00pm GMT) Email: [email protected] CENTRAL/SOUTH AMERICA: Spanish Phone: 303–308–7143 (Mon–Fri 8:00am to 5:00pm MST) Email: ONlit–[email protected] Toll–Free from Mexico: Dial 01–800–288–2872 for Access – then Dial 866–297–9322 ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support Phone: 303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong & Singapore: 001–800–4422–3781 Email: ONlit–[email protected] JAPAN: ON Semiconductor, Japan Customer Focus Center 4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031 Phone: 81–3–5740–2700 Email: [email protected] ON Semiconductor Website: http://onsemi.com EUROPEAN TOLL–FREE ACCESS*: 00–800–4422–3781 *Available from Germany, France, Italy, UK, Ireland For additional information, please contact your local Sales Representative. http://onsemi.com 8 BSS123LT1/D