WF128K32-XXX5 128KX32 5V FLASH MODULE, SMD 5962-94716 FEATURES n Access Times of 50*, 60, 70, 90, 120, 150ns n 5 Volt Programming. 5V ± 10% Supply n Packaging: n Low Power CMOS, 1mA Standby Typical •66 pin, PGA Type, 1.075 inch square, Hermetic Ceramic HIP (Package 400) n Embedded Erase and Program Algorithms •68 lead, Hermetic CQFP (G2U)1, 22.4mm (0.880 inch) square, 3.56mm (0.140 inch) high (Package 510) n Built-in Decoupling Caps and Multiple Ground Pins for •68 lead, Hermetic CQFP (G1U), 23.9mm (0.940 inch) square, 3.56mm (0.140 inch) high (Package 519) n Page Program Operation and Internal Program Control Time •68 lead, Hermetic CQFP (G1T), 23.9mm (0.940 inch) square, 4.06mm (0.160 inch) high (Package 524) n Weight n TTL Compatible Inputs and CMOS Outputs Low Noise Operation WF128K32-XG1UX5 - 5 grams typical n Sector Architecture WF128K32-XG1TX5 - 5 grams typical •8 equal size sectors of 16KBytes each WF128K32-XG2UX51 - 8 grams typical •Any combination of sectors can be concurrently erased. Also supports full chip erase WF128K32-XH1X5 - 13 grams typical Note 1: Package Not Recommended For New Design Note: For programming information refer to Flash Programming 1M5 Application Note. * The access time of 50ns is available in Industrial and Commercial temperature ranges only. n 100,000 Erase/Program Cycles Typical, 0°C to +70°C n Organized as 128Kx32 n Commercial, Industrial and Military Temperature Ranges FIG. 1 PIN CONFIGURATION FOR WF128K32N-XH1X5 TOP VIEW PIN DESCRIPTION I/O 0-31 Data Inputs/Outputs I/O8 WE2 I/O15 I/O24 VCC I/O31 A 0-16 Address Inputs I/O9 CS2 I/O14 I/O25 CS4 I/O30 WE 1-4 Write Enables CS1-4 Chip Selects I/O10 GND I/O13 I/O26 WE4 I/O29 A14 I/O11 I/O12 A7 I/O27 I/O28 A16 A10 OE A12 A4 A1 A11 A9 NC NC A5 A2 A0 A15 WE1 A13 A6 A3 NC VCC I/O7 A8 WE3 I/O23 I/O0 CS1 I/O6 I/O16 CS3 I/O22 I/O1 NC I/O5 I/O17 GND I/O21 I/O2 I/O3 I/O4 I/O18 I/O19 I/O20 June 2002 Rev. 5 OE Output Enable VCC Power Supply GND Ground NC Not Connected BLOCK DIAGRAM 1 White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com WF128K32-XXX5 FIG. 3 PIN CONFIGURATION FOR WF128K32-XG1UX5, WF128K32-XG1TX5 AND WF128K32-XG2UX51 PIN DESCRIPTION NC A0 A1 A2 A3 A4 A5 CS3 GND CS4 WE1 A6 A7 A8 A9 A10 VCC TOP VIEW 9 8 7 6 5 4 3 2 1 68 67 66 65 64 63 62 61 I/O0 I/O1 I/O2 I/O3 I/O4 I/O5 I/O6 I/O7 GND I/O8 I/O9 I/O10 I/O11 I/O12 I/O13 I/O14 I/O15 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 I/O16 I/O17 I/O18 I/O19 I/O20 I/O21 I/O22 I/O23 GND I/O24 I/O25 I/O26 I/O27 I/O28 I/O29 I/O30 I/O31 I/O 0-31 Data Inputs/Outputs A 0-16 Address Inputs WE 1-4 Write Enables CS1-4 Chip Selects OE Output Enable VCC Power Supply GND Ground NC Not Connected BLOCK DIAGRAM A16 CS1 OE CS2 NC WE2 WE3 WE4 NC NC NC A15 A14 A13 A12 A11 VCC 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 Note 1: Package Not Recommended For New Design White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com 2 WF128K32-XXX5 ABSOLUTE MAXIMUM RATINGS (1) RECOMMENDED OPERATING CONDITIONS Symbol Min Max Unit Operating Temperature -55 to +125 °C Supply Voltage V CC 4.5 5.5 V Supply Voltage Range (VCC) -2.0 to +7.0 V Input High Voltage VIH 2.0 V CC + 0.3 V Signal voltage range (any pin except A9) (2) -2.0 to +7.0 V Input Low Voltage VIL -0.5 +0.8 V Storage Temperature Range -65 to +150 °C Operating Temp. (Mil.) TA -55 +125 °C +300 °C A9 Voltage for Sector Protect VID 11.5 12.5 V Parameter Parameter Unit Lead Temperature (soldering, 10 seconds) Data Retention Mil Temp 10 years Endurance (write/erase cycles) Mil Temp CAPACITANCE 10,000 cycles min. A9 Voltage for sector protect (VID) (3) -2.0 to +14.0 (TA = +25ºC) V NOTES: Parameter 1. Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2. Minimum DC voltage on input or I/O pins is -0.5V. During voltage transitions, inputs may overshoot Vss to -2.0 V for periods of up to 20ns. Maximum DC voltage on output and I/O pins is Vcc + 0.5V. During voltage transitions, outputs may overshoot to Vcc + 2.0 V for periods of up to 20ns. 3. Minimum DC input voltage on A9 pin is -0.5V. During voltage transitions, A9 may overshoot Vss to -2V for periods of up to 20ns. Maximum DC input voltage on A9 is +13.5V which may overshoot to 14.0 V for periods up to 20ns. Symbol Conditions OE capacitance COE VIN = 0 V, f = 1.0 MHz WE1-4 capacitance HIP (PGA) CQFP G2U/G1U/G1T CWE VIN = 0 V, f = 1.0 MHz Max 50 Unit pF pF 20 15 CS1-4 capacitance CCS VIN = 0 V, f = 1.0 MHz 20 pF Data I/O capacitance CI/O VI/O = 0 V, f = 1.0 MHz 20 pF Address input capacitance CAD VIN = 0 V, f = 1.0 MHz 50 pF This parameter is guaranteed by design but not tested. DC CHARACTERISTICS - CMOS COMPATIBLE (V CC = 5.0V, VSS = 0V, T A = -55°C TO +125°C) Parameter Symbol Conditions Unit Min Input Leakage Current Output Leakage Current Max I LI VCC = 5.5, VIN = GND to VCC 10 I LOx32 VCC = 5.5, VIN = GND to VCC 10 µA µA VCC Active Current for Read (1) I CC1 CS = VIL, OE = VIH 140 mA VCC Active Current for Program or Erase (2) I CC2 CS = VIL, OE = VIH 200 mA VCC Standby Current I CC3 VCC = 5.5, CS = VIH, f = 5MHz 6.5 mA VCC Static Current I CC4 VCC = 5.5, CS = VIH 0.6 mA Output Low Voltage VOL IOL = 8.0 mA, VCC = 4.5 0.45 V Output High Voltage VOH1 IOH = -2.5 mA, VCC = 4.5 0.85 x VCC V Output High Voltage VOH2 IOH = -100 µA, VCC = 4.5 VCC -0.4 V Low VCC Lock Out Voltage VLKO 3.2 V NOTES: 1. The ICC current listed includes both the DC operating current and the frequency dependent component (at 5 MHz). The frequency component typically is less than 2 mA/MHz, with OE at VIH. 2. ICC active while Embedded Algorithm (program or erase) is in progress. 3. DC test conditions: VIL = 0.3V, VIH = VCC - 0.3V 3 White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com WF128K32-XXX5 AC CHARACTERISTICS WRITE/ERASE/PROGRAM OPERATIONS, CS CONTROLLED (VCC = 5.0V, VSS = 0V, TA = -55°C TO+125°C) Parameter Symbol -50 Min -60 Max Min -70 Max Min -90 Max Min -120 Max Min -150 Max Min Unit Max Write Cycle Time t AVAV t WC 50 60 70 90 120 150 ns WE Setup Time tWLEL tWS 0 0 0 0 0 0 ns CS Pulse Width t ELEH t CP 25 30 35 45 50 50 ns Address Setup Time t AVEL t AS 0 0 0 0 0 0 ns Data Setup Time t DVEH tDS 25 30 30 45 50 50 ns Data Hold Time t EHDX tDH 0 0 0 0 0 0 ns Address Hold Time tELAX t AH 40 45 45 45 50 50 ns WE Hold from WE High t EHWH t WH 0 0 0 0 0 0 ns CS Pulse Width High tEHEL tCPH 20 20 20 20 20 20 ns Duration of Programming Operation t WHWH1 14 Duration of Erase Operation t WHWH2 2.2 t GHEL 0 Read Recovery before Write Chip Programming Time 14 60 2.2 14 60 0 12.5 14 2.2 60 0 12.5 2.2 14 60 0 12.5 FIG. 4 AC TEST CIRCUIT 2.2 14 60 0 12.5 2.2 µs 60 sec 0 12.5 ns 12.5 sec AC TEST CONDITIONS Parameter Typ Unit Input Pulse Levels VIL = 0, VIH = 3.0 V Input Rise and Fall 5 ns Input and Output Reference Level 1.5 V Output Timing Reference Level 1.5 V Notes: VZ is programmable from -2V to +7V. IOL & IOH programmable from 0 to 16mA. Tester Impedance Z0 = 75 ý. VZ is typically the midpoint of VOH and VOL. IOL & IOH are adjusted to simulate a typical resistive load circuit. ATE tester includes jig capacitance. White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com 4 WF128K32-XXX5 AC CHARACTERISTICS WRITE/ERASE/PROGRAM OPERATIONS, WE CONTROLLED (V CC = 5.0V, VSS = 0V, TA = -55°C TO +125°C) Parameter Symbol -50 Min -60 Max Min -70 Max Min -90 Max Min -120 Max Min -150 Max Min Unit Max Write Cycle Time t AVAV t WC 50 60 70 90 120 150 Chip Select Setup Time tELWL tCS 0 0 0 0 0 0 ns Write Enable Pulse Width t WLWH t WP 25 30 35 45 50 50 ns Address Setup Time tAVWL t AS 0 0 0 0 0 0 ns Data Setup Time t DVWH tDS 25 30 30 45 50 50 ns Data Hold Time t WHDX tDH 0 0 0 0 0 0 ns Address Hold Time tWLAX t AH 40 45 45 45 50 50 ns Chip Select Hold Time t WHEH tCH 0 0 0 0 0 0 ns Write Enable Pulse Width High t WHWL t WPH 20 20 20 20 20 20 ns Duration of Byte Programming Operation (min) t WHWH1 14 Sector Erase Time t WHWH2 2.2 t GHWL 0 Read Recovery Time Before Write VCC Setup Time tVCS 14 60 14 2.2 60 0 50 60 0 50 Chip Programming Time 14 2.2 60 0 50 12.5 14 2.2 12.5 14 2.2 60 0 50 µs 2.2 60 0 50 12.5 ns ns 50 12.5 sec µs 12.5 12.5 sec Output Enable Setup Time tOES 0 0 0 0 0 0 ns Output Enable Hold Time (1) 1. For Toggle and Data Polling. tOEH 10 10 10 10 10 10 ns AC CHARACTERISTICS READ ONLY OPERATIONS (VCC = 5.0V, VSS = 0V, TA = -55°C TO +125°C) Parameter Symbol -50 Min -60 Max Min Read Cycle Time t AVAV t RC Address Access Time t AVQV t ACC 50 Chip Select Access Time t ELQV t CE 50 60 OE to Output Valid t GLQV tOE 25 30 Chip Select to Output High Z (1) t EHQZ t DF 20 20 OE High to Output High Z (1) t GHQZ t DF 20 20 t AXQX tOH Output Hold from Address, CS or OE Change, whichever is first 1. Guaranteed by design, not tested. 50 -70 Max 60 Min 70 60 0 0 5 -90 Max Min 90 70 0 -120 Max Min -150 Max 120 Min Unit Max 150 ns 90 120 150 ns 70 90 120 150 ns 35 40 50 55 ns 20 25 30 35 ns 20 25 30 35 ns 0 0 0 ns White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com WF128K32-XXX5 FIG. 5 AC WAVEFORMS FOR READ OPERATIONS White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com 6 WF128K32-XXX5 FIG. 6 WRITE/ERASE/PROGRAM OPERATION, WE CONTROLLED NOTES: 1. PA is the address of the memory location to be programmed. 2. PD is the data to be programmed at byte address. 3. D7 is the output of the complement of the data written to the device (for each chip). 4. DOUT is the output of the data written to the device. 5.Figure indicates last two bus cycles of four bus cycle sequence. 7 White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com WF128K32-XXX5 FIG. 7 AC WAVEFORMS CHIP/SECTOR ERASE OPERATIONS Notes: 1. SA is the sector address for Sector Erase. White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com 8 WF128K32-XXX5 FIG. 8 AC WAVEFORMS FOR DATA POLLING DURING EMBEDDED ALGORITHM OPERATIONS 9 White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com WF128K32-XXX5 FIG. 9 WRITE/ERASE/PROGRAM OPERATION, CS CONTROLLED NOTES: 1. PA represents the address of the memory location to be programmed. 2. PD represents the data to be programmed at byte address. 3. D7 is the output of the complement of the data written to the device (for each chip). 4. DOUT is the output of the data written to the device. 5. Figure indicates the last two bus cycles of a four bus cycle sequence. White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com 10 WF128K32-XXX5 PACKAGE 400: 66 PIN, PGA TYPE, CERAMIC HEX-IN-LINE PACKAGE, HIP (H1) ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES 11 White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com WF128K32-XXX5 PACKAGE510: 68LEAD,CERAMICQUADFLATPACK,CQFP(G2U)1 TheWhite68leadG2UCQFP fills the same fit and function as the JEDEC 68 lead CQFJ or 68 PLCC. But the G2U has the TCEandleadinspection advantageoftheCQFPform. Note 1: Package Not Recommended For New Design ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com 12 WF128K32-XXX5 PACKAGE519:68LEAD,CERAMICQUADFLATPACK,LOWPROFILECQFP(G1U) ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES 13 White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com WF128K32-XXX5 PACKAGE524:68LEAD,CERAMICQUADFLATPACK,LOWPROFILECQFP(G1T) ALL LINEAR DIMENSIONS ARE MILLIMETERS AND PARENTHETICALLY IN INCHES White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com 14 WF128K32-XXX5 ORDERING INFORMATION W F 128K32 X - XXX X X 5 X LEAD FINISH: Blank = Gold plated leads A = Solder dip leads VPP PROGRAMMING VOLTAGE 5 = 5V DEVICE GRADE: Q = MIL - STD 833 Compliant M = Military Screened -55°C to +125°C I = Industrial -40°C to +85°C C = Commercial 0°C to + 70°C PACKAGE TYPE: H1 = 1.075" sq. Ceramic Hex In-line Package, HIP (Package 400) G2U1 = 22.4mm Ceramic Quad Flat Pack, Low Profile CQFP (Package 510) G1U = 23.9mm Ceramic Quad Flat Pack, Low Profile CQFP (Package 519) G1T = 23.9mm Ceramic Quad Flat Pack, Low Profile CQFP (Package 524) ACCESS TIME (ns) IMPROVEMENT MARK N = No Connect at pin 8, 21, 28 and 39 in HIP for Upgrade ORGANIZATION, 128K x 32 User configurable as 256K x 16 or 512K x 8 Flash WHITE ELECTRONIC DESIGNS CORP. Note 1: Package Not Recommended For New Design 15 White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com WF128K32-XXX5 DEVICETYPE SPEED PACKAGE SMD NO. 128K x 32 Flash 150ns 66 pin HIP (H1) 5962-94716 01H8X 128K x 32 Flash 120ns 66 pin HIP (H1) 5962-94716 02H8X 128K x 32 Flash 90ns 66 pin HIP (H1) 5962-94716 03H8X 128K x 32 Flash 70ns 66 pin HIP (H1) 5962-94716 04H8X 128K x 32 Flash 60ns 66 pin HIP (H1) 5962-94716 05H8X 128K x 32 Flash 150ns 68 lead CQFP (G1U) 5962-94716 01H9X 128K x 32 Flash 120ns 68 lead CQFP (G1U) 5962-94716 02H9X 128K x 32 Flash 90ns 68 lead CQFP (G1U) 5962-94716 03H9X 128K x 32 Flash 70ns 68 lead CQFP (G1U) 5962-94716 04H9X 128K x 32 Flash 60ns 68 lead CQFP (G1U) 5962-94716 05H9X 128K x 32 Flash 150ns 68 lead CQFP (G2U)1 5962-94716 01HNX1 128K x 32 Flash 120ns 68 lead CQFP (G2U) 5962-94716 02HNX1 128K x 32 Flash 90ns 1 68 lead CQFP (G2U) 5962-94716 03HNX1 128K x 32 Flash 70ns 68 lead CQFP (G2U)1 5962-94716 04HNX1 128K x 32 Flash 60ns 68 lead CQFP (G2U)1 1 5962-94716 05HNX1 Note 1: Package Not Recommended For New Design White Electronic Designs Corporation • (602) 437-1520 • www.whiteedc.com 16