AD BUF04GP

a
FEATURES
Bandwidth – 110 MHz
Slew Rate – 3000 V/ms
Low Offset Voltage – <1 mV
Very Low Noise – < 4 nV/√Hz
Low Supply Current – 8.5 mA Mux
Wide Supply Range – 65 V to 615 V
Drives Capacitive Loads
Pin Compatible with BUF03
Closed-Loop
High Speed Buffer
BUF04*
FUNCTIONAL BLOCK DIAGRAMS
1
BUF04
APPLICATIONS
Instrumentation Buffer
RF Buffer
Line Driver
High Speed Current Source
Op Amp Output Current Booster
High Performance Audio
High Speed AD/DA
GENERAL DESCRIPTION
The BUF04 is a wideband, closed-loop buffer that combines
state of the art dynamic performance with excellent dc
performance. This combination enables designers to maximize
system performance without any speed versus dc accuracy
compromises.
Built on a high speed Complementary Bipolar (CB) process for
better power performance ratio, the BUF04 consumes less than
8.5 mA operating from ±5 V or ±15 V supplies. With a 2000 V/µs
min slew rate, and 100 MHz gain bandwidth product, the
BUF04 is ideally suited for use in high speed applications where
low power dissipation is critical.
Full ± 10 V output swing over the extended temperature range
along with outstanding ac performance and high loop gain
accuracy makes the device useful in high speed data acquisition
systems.
Plastic DIP
8-Lead and Cerdip
(P, Z Suffix)
8-Lead Narrow-Body SO
(S Suffix)
NULL 1
BUF04
8
NULL
NC
Top View
7
V+
IN 3
6
OUT
V– 4
5
NC
2
NC = NO CONNECT
High slew rate and very low noise and THD, coupled with wide
input and output dynamic range, make the BUF04 an excellent
choice for video and high performance audio circuits.
The BUF04’s inherent ability to drive capacitive loads over a
wide voltage and temperature range makes it extremely useful
for a wide variety of applications in military, industrial, and
commercial equipment.
The BUF04 is specified over the extended industrial (–40°C to
+85°C) and military (–55°C to +125°C) temperature range.
BUF04s are available in plastic and ceramic DIP plus SO-8
surface mount packages.
Contact your local sales office for MIL-STD-883 data sheet and
availability.
*Patent pending.
REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 617/329-4700
Fax: 617/326-8703
BUF04–SPECIFICATIONS
ELECTRICAL CHARACTERISTICS (@ V = 615.0 V, T = +258C unless otherwise noted)
S
Parameter
Symbol
INPUT CHARACTERISTICS
Offset Voltage
VOS
Input Bias Current
IB
Input Voltage Range
Offset Voltage Drift
Offset Null Range
VCM
∆VOS/∆T
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Current – Continuous
Peak Output Current
TRANSFER CHARACTERISTICS
Gain
Gain Linearity
POWER SUPPLY
Power Supply Rejection Ratio
Supply Current
DYNAMIC PERFORMANCE
Slew Rate
Bandwidth
Bandwidth
Bandwidth
Settling Time
Differential Phase
A
Conditions
–40°C ≤ TA ≤ +85°C
VCM = 0
–40°C ≤ TA ≤ +85°C
Max
Units
0.3
1.3
0.7
2.2
± 13
30
± 25
1
4
5
10
mV
mV
µA
µA
V
µV/°C
mV
± 11.1
± 11
± 13.5
± 13.15
± 65
± 80
V
V
V
V
mA
mA
RL = 2 kΩ
–40°C ≤ TA ≤ +85°C
RL = 1 kΩ, VO = ± 10 V
RL = 150 kΩ
0.995
0.995
0.9985 1.005
0.9980 1.005
0.005
0.008
V/V
V/V
%
%
VS = ± 4.5 V to ± 18 V
–40°C ≤ TA ≤ +85°C
VO = 0 V, RL = ∞
–40°C ≤ TA ≤ +85°C
76
76
93
93
6.9
6.9
dB
dB
mA
mA
SR
BW
BW
BW
RL = 2 kΩ, CL = 70 pF
–3 dB, CL = 20 pF, RL = ∞
–3 dB, CL = 20 pF, RL = 1 kΩ
–3 dB, CL = 20 pF, RL = 150 Ω
VIN = ±10 V Step to 0.1%
f = 3.58 MHz, RL = 150 Ω
f = 4.43 MHz, RL = 150 Ω
f = 3.58 MHz, RL = 150 Ω
f = 4.43 MHz, RL = 150 Ω
2000
en
in
f = 1 kHz
f = 1 kHz
IOUT
IOUTP
AVCL
NL
PSRR
ISY
RL = 150 Ω,
–40°C ≤ TA ≤ +85°C
RL = 2 kΩ,
–40°C ≤ TA ≤ +85°C
Typ
± 10.5
± 10
± 13
± 13
± 50
VO
Differential Gain
Note 2
Input Capacitance
NOISE PERFORMANCE
Voltage Noise Density
Current Noise Density
Min
8.5
8.5
3000
110
110
110
60
0.02
0.03
0.014
0.008
3
V/µs
MHz
MHz
MHz
ns
Degrees
Degrees
%
%
pF
4
2
nV/√Hz
pA/√Hz
NOTE
1
Long term offset voltage is guaranteed by a 1000 hour life test performed on three independent lots at +125 °C with an LTPD of 1.3.
Specifications subject to change without notice.
–2–
REV. 0
BUF04
ELECTRICAL CHARACTERISTICS (@ V = 65.0 V, T = +258C unless otherwise noted)
S
Parameter
Symbol
INPUT CHARACTERISTICS
Offset Voltage
VOS
Input Bias Current
IB
Input Voltage Range
Offset Voltage Drift
Offset Null Range
VCM
∆VOS/∆T
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Current - Continuous
Peak Output Current
TRANSFER CHARACTERISTICS
Gain
Gain Linearity
POWER SUPPLY
Power Supply Rejection Ratio
Supply Current
DYNAMIC PERFORMANCE
Slew Rate
Bandwidth
Bandwidth
Bandwidth
Differential Phase
VO
IOUT
IOUTP
AVCL
NL
PSRR
ISY
Conditions
Min
–40°C ≤ TA ≤ +85°C
VCM = 0 V
–40°C ≤ TA ≤ +85°C
RL = 150 Ω,
–40°C ≤ TA ≤ +85°C
RL = 2 kΩ,
–40°C ≤ TA ≤ +85°C
± 3.0
± 2.75
± 3.0
± 3.0
± 40
Note 2
Typ
Max
Units
0.8
1.0
0.15
1.6
± 3.0
30
± 25
2.0
4
5
10
mV
mV
µA
µA
V
µV/°C
mV
± 75
V
V
V
V
mA
mA
± 3.00
± 3.6
± 3.35
RL = 2 kΩ,
–40°C ≤ TA ≤ +85°C
RL = 1 kΩ
0.995
0.995
0.9977 1.005
1.005
0.005
V/V
V/V
%
VS = ± 4.5 V to ± 18 V
–40°C ≤ TA ≤ +85°C
VO = 0 V, RL = ∞
–40°C ≤ TA ≤ +85°C
76
76
93
93
6.60
6.70
dB
dB
mA
mA
RL = 2 kΩ, CL = 70 pF
–3 dB, CL = 20 pF, RL = ∞
–3 dB, CL = 20 pF, RL = 1 kΩ
–3 dB, CL = 20 pF, RL = 150 Ω
f = 3.58 MHz, RL = 150 Ω
f = 4.43 MHz, RL = 150 Ω
f = 3.58 MHz, RL = 150 Ω
f = 4.43 MHz, RL = 150 Ω
2000
100
100
100
0.13
0.15
0.04
0.06
V/µs
MHz
MHz
MHz
Degrees
Degrees
%
%
en
in
f = 1 kHz
f = 1 kHz
4
2
nV/√Hz
pA/√Hz
NOTE
1
Long term offset voltage is guaranteed by a 1000 hour life test performed on three independent lots at +125 °C, with an LTPD of 1.3.
Specifications subject to change without notice.
REV. 0
8
8
SR
BW
BW
BW
Differential Gain
NOISE PERFORMANCE
Voltage Noise Density
Current Noise Density
A
–3–
BUF04
WAFER TEST LIMITS (@ V = 615.0 V, T = +258C unless otherwise noted)
S
A
Parameter
Symbol
Conditions
Limit
Units
Offset Voltage
VOS
VOS
IB
PSRR
VO
ISY
AVCL
VS = ± 15 V
VS = ± 5 V
VCM = 0 V
V = ± 4.5 V to ± 18 V
RL = 150 Ω
VO = 0 V, RL = 2 kΩ
VO = ± 10 V, RL = 2 kΩ
1
2
5
76
± 10.5
8.5
1 ± 0.005
mV max
mV max
µA max
dB
V min
mA max
V/V
Input Bias Current
Power Supply Rejection Ratio
Output Voltage Range
Supply Current
Gain
NOTE
Electrical tests and wafer probe to the limits shown. Due to variations in assembly methods and normal yield loss, yield after packaging is not guaranteed for standard
product dice. Consult factory to negotiate specifications based on dice lot qualifications through sample lot assembly and testing.
ABSOLUTE MAXIMUM RATINGS 1
DICE CHARACTERISTICS
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 18 V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 18 V
Maximum Power Dissipation . . . . . . . . . . . . . . . See Figure 16
Storage Temperature Range
Z Package . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to +175°C
P, S Package . . . . . . . . . . . . . . . . . . . . . . . –65°C to +150°C
Operating Temperature Range
BUF04Z . . . . . . . . . . . . . . . . . . . . . . . . . . –55°C to +125°C
BUF04S, P . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C
Junction Temperature Range
Z Package . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to +150°C
P, S Package . . . . . . . . . . . . . . . . . . . . . . . –65°C to +150°C
Lead Temperature Range (Soldering 60 sec) . . . . . . . . +300°C
Package Type
θJA2
θJC
Units
8-Pin Cerdip (Z)
8-Pin Plastic DIP (P)
8-Pin SOIC (S)
148
103
158
16
43
43
°C/W
°C/W
°C/W
BUF04 Die Size 0.075 x 0.064 inch, 5,280 Sq. Mils
Substrate (Die Backside) Is Connected to V+
Transistor Count 45.
NOTES
1
Absolute maximum ratings apply to both DICE and packaged parts, unless
otherwise noted.
2
θJA is specified for the worst case conditions, i.e., θJA is specified for device in socket
for cerdip, P-DIP, and LCC packages; θJA is specified for device soldered in circuit
board for SOIC package.
ORDERING GUIDE
Model
Temperature
Range
Package
Description
Package
Option
BUF04AZ/883
BUF04GP
BUF04GS
BUF04GBC
–55°C to +125°C
–40°C to +85°C
–40°C to +85°C
+25°C
Cerdip
Plastic DIP
SO
DICE
Q-8
N-8
SO-8
DICE
–4–
REV. 0
Typical Performance Characteristics–BUF04
200
150
VS = ±15V
315 PLASTIC DIPS
TA = +25°C
120
120
UNITS
UNITS
90
60
80
30
40
0
–0.1
0.0
0.1
0.2
0.3
OFFSET – mV
0.4
0.5
0
–0.15
0.6
–0.5
0
0.5
0.1
0.15
0.2
Figure 4. Input Offset Voltage (VOS) Distribution @
± 15 V, Cerdip
125
125
VS = ±5V
315 PLASTIC DIPS
TA = +25°C
100
VS = ±5V
315 CERDIPS
TA = +25°C
100
75
UNITS
UNITS
75
50
50
25
25
0
0
0
0.2
0.4
0.6
0.8
OFFSET – mV
1.0
1.2
1.4
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
OFFSET – mV
Figure 2. Input Offset Voltage (VOS) Distribution @
± 5 V, P-DIP
Figure 5. Input Offset Voltage (VOS) Distribution @
± 5 V, Cerdip
2.0
0
VS = ±5V
1.0
–1.0
INPUT BIAS CURRENT – µA
±5V
0
±15V
OFFSET – mV
–0.1
OFFSET – mV
Figure 1. Input Offset Voltage (VOS) Distribution @
± 15 V, P-DIP
–1.0
–2.0
–3.0
–4.0
VS = ±15V
–2.0
–3.0
–4.0
–5.0
–5.0
–6.0
–6.0
–75
–50
–25
0
25
50
75
100
125
–75
TEMPERATURE – °C
–50
–25
0
25
50
75
100
TEMPERATURE – °C
Figure 3. Input Offset Voltage (VOS) vs. Temperature
REV. 0
VS = ±15V
315 CERDIPS
TA = +25°C
160
Figure 6. Input Bias Current vs. Temperature
–5–
125
BUF04
8.0
50
TA = +25°C
45
40
OUTPUT IMPEDANCE – Ω
SUPPLY CURRENT – mA
7.5
VS = ±18V
7.0
VS = ±15V
6.5
VS = ±5V
35
VS = ±5V
30
25
20
15
6.0
10
VS = ±15V
5
5.5
–75
0
–50
–25
0
25
50
75
100
125
1k
10k
100k
1M
FREQUENCY – Hz
TEMPERATURE – °C
100M
Figure 10. Output Impedance vs. Frequency
Figure 7. Supply Current vs. Temperature
5.0
15
13
RL = 2k Ω
4.5
RL = 1k Ω
4.0
OUTPUT SWING – Volts
VS = ±15V
14
OUTPUT SWING – Volts
10M
12
RL = 150 Ω
11
RL = 150 Ω
–11
–12
RL = 1k Ω
–13
–14
–50
–25
0
25
50
TEMPERATURE – °C
RL = 2kΩ , 1k Ω
3.5
RL = 150Ω
3.0
RL = 150 Ω
–3.0
–3.5
RL = 2kΩ , 1kΩ
–4.0
–4.5
RL = 2k Ω
–15
–75
VS = ±5V
75
100
–5.0
–75
125
Figure 8. Output Voltage Swing vs. Temperature @ ± 15 V
–50
–25
25
50
0
TEMPERATURE – °C
75
100
125
Figure 11. Output Voltage Swing vs. Temperature @ ± 5 V
16
5
14
OUTPUT SWING – Volts
OUTPUT SWING – Volts
4
POSITIVE
SWING
3
ABS NEGATIVE
SWING
2
POSITIVE
SWING
10
8
ABS NEGATIVE
SWING
6
VS = ±15V
TA = +25°C
4
VS = ±5V
TA = +25°C
1
12
2
0
0
10
100
1k
10k
100k
10
1M
100
1k
10k
LOAD RESISTANCE – Ω
LOAD RESISTANCE – Ω
Figure 9. Maximum VOUT Swing vs. Load @ ± 5 V
Figure 12. Maximum VOUT Swing vs. Load @ ± 15 V
–6–
REV. 0
BUF04
1.5
0.5
POWER DISSIPATION – W
INPUT BIAS CURRENT – µA
TJ MAX = 150°C
FREE AIR
NO HEAT SINK
P DIP
ΘJA = 103°C/W
TA = +25°C
0
–0.5
–1.0
CERDIP
ΘJA = 148°C/W
1.0
SOIC
ΘJA = 158°C/W
0.5
–1.5
–2.0
–10
0
–8
–6
–4
–2
0
2
4
6
8
10
0
25
COMMON MODE VOLTAGE – Volts
Figure 13. Bias Current vs. Input Voltage
75
85
100
125
Figure 16. Maximum Power Dissipation vs.
Ambient Temperature
100
100
INPUT NOISE VOLTAGE
SPECTRAL DENSITY – nV/ Hz
TA = +25°C
VS = ±5, ±15V
90
POWER SUPPLY REJECTION – dB
50
TEMPERATURE – °C
80
– PSRR
70
60
50
40
+PSRR
30
10
20
10
0
0
1k
10k
100k
1M
10M
1
100M
10
100
1k
10k
Figure 14. Power Supply Rejection vs. Frequency
6000
VS = ±15V
VS = ±15V
SWING = ±10V
TA = +25°C
5000
5000
SLEW RATE – V/µs
SLEW RATE – V/µs
+EDGE
4000
3000
–EDGE
2000
POSITIVE
SLEW RATE
4000
3000
NEGATIVE
SLEW RATE
2000
1000
1000
0
–50
–25
0
25
50
75
100
125
0
50
100
150
200
CAPACITIVE LOAD – pF
TEMPERATURE – °C
Figure 15. Slew Rate vs. Temperature
REV. 0
1M
Figure 17. Input Noise Voltage vs. Frequency
6000
0
–75
100k
FREQUENCY – Hz
FREQUENCY – Hz
Figure 18. Slew Rate vs. Capacitive Loads
–7–
250
BUF04
TA = +25°C
VS = ±5V
–67.5
BANDWIDTH – MHz
–90
100
PHASE @
RL = 150 Ω
–112.5
75
50
PHASE @
RL = 2k Ω
25
BANDWIDTH
–135
0
50
100
150
–180
250
200
BANDWIDTH
100
–67.5
–90
RL = 150 Ω
75
–112.5
RL = 2k Ω
–135
50
PHASE
25
–157.5
0
TA = +25°C
VS = ±15V
125
PHASE – Deg
BANDWIDTH – MHz
125
–45
150
PHASE – Deg
–45
150
–157.5
–180
250
0
0
50
100
CAPACITANCE – pF
150
200
CAPACITANCE – pF
Figure 19. Bandwidth and Phase vs.
Capacitive Loads @ ± 5 V
Figure 22. Bandwidth & Phase vs.
Capacitive Loads @ ± 15 V
140
200
RL= 2kΩ
130
TA = +25°C
VS = ±15V
–55°C
BANDWIDTH – MHz
BANDWIDTH – MHz
150
120
+25°C
110
+125°C
100
100
50
90
80
±10
0
100
±15
1k
Figure 20. Bandwidth vs. Supply Voltage and
Temperature
1.5
2
0
0
GAIN
–2
–1.0
–8
–6
–4
–2
2
4
0
OUTPUT VOLTAGE – Volts
6
8
GAIN DEVIATION – dB
0.5
–0.5
0.050
4
PHASE
1.5
0.075
PHASE DEVIATION – Degrees
GAIN DEVIATION – dB
1.0
–1.5
–10
Figure 23. Bandwidth vs. Loads
6
VS = ±15V
VIN = 0.1VRMS
FREQUENCY = 10MHz
RL = 150Ω
10k
RESISTIVE LOAD – Ω
SUPPLY VOLTAGE –Volts
0.025
1.0
0.5
GAIN
0
0
–0.025
–0.5
PHASE
–4
–0.050
–6
–0.075
–10
10
VS = ±15V
VIN = 0.1VRMS
FREQUENCY = 10MHz
RL = 2k Ω
PHASE DEVIATION – Degrees
±5
–1.0
–1.5
–8
–6
–4
–2
2
4
0
OUTPUT VOLTAGE – Volts
6
8
10
Figure 24. Gain and Phase Deviation, RL = 2 kΩ
Figure 21. Gain and Phase Deviation, RL = 150 Ω
–8–
REV. 0
BUF04
DLY
100
INPUT
(50mV/DIV)
90
OUTPUT
(50mV/DIV)
90
OUTPUT
(2V/DIV)
10
10
0%
0%
50mV
50mV
10ns
2V
VS = ±15V, RL = 2kΩ, CL = 15pF
AUDIO PRECISION BUF04 THD+N (%) vs FREQ (Hz)
0.1
2V
50ns
VS = ±15V, RL = 2kΩ, CL = 15pF
Figure 25. Small-Signal Transient Response
Figure 26. Large-Signal Transient Response
07 MAR 93 21:31:53
12
VS = ±15V
TA = +25°C
RL = 150 Ω
9
VS= ±15V
A
A : VIN = 7.75Vrms, RL= 150W
C : VIN = 0.775Vrms, RL= 150W
LPF=80kHz
B : VIN = 7.75Vrms, RL= 600W
B
D : VIN = 0.775Vrms, RL= 600W
A
375.0ns
100
INPUT
(2V/DIV)
6
CL = 100pF
GAIN – dB
0.010
C
B
C
D
3
CL = 50pF
CL = 0pF
0
–3
150
0.001
D
Ω
BUF04
–6
10 Ω
CL
–9
T
0.0001
20
100
1k
10k
–12
10k
20k
Figure 27. THD + Noise vs. Amplitude
100k
1M
10M
FREQUENCY – Hz
100M
1000M
Figure 28. Bandwidth vs. Frequency
FUNCTIONAL DESCRIPTION
The BUF04 is a closed-loop voltage buffer based on a current
feedback architecture. Its high open-loop transimpedance, high
output current drive capability, and its low input offset voltage
makes it useful in a variety of applications, such as buffering the
inputs of sampling and flash A/D converters, audio and video
line drivers, active filters, and precision op amp hoosters.
Q11
Q5
Q7
Q3
C1
Q9
A transistor-level equivalent circuit for the BUF04 is illustrated
in Figure 29. The input stage consists of a pair of emitter
follower transistors, Q1 and Q2, whose outputs drive a second
set of transistors, Q3 and Q4. The emitters of Q3 and Q4 are
connected together through diodes, D1 and D2, to form a low
impedance input for the feedback signal (in current mode) from
the output stage. The outputs of Q3 and Q4 are then
“mirrored” to Q5 and Q6 which form the gain stage of the
BUF04. The signal is taken from the collectors of Q5 and Q6
which drive a “Darlington-connected” output stage made up of
transistors Q7-Q10. Three R-C networks (R1–C1, R2–C2, and
R3–C3) form feed-forward paths which bypass certain sections
of the BUF04 for improved high frequency performance and
capacitive load drive capability. Since the signal conveyed
internally in the BUF04 is a current, the frequency response
and slew rate of the BUF04 are insensitive to supply voltage
variations.
REV. 0
Q13
RFB
100Ω
D1
C3
20Ω
R3
Q2
VIN
Q1
D2
R2
20Ω
VOUT
Q10
Q4
C2
Q8
Q14
Q12
Q6
Figure 29. Transistor-Level Equivalent Circuit
An interesting feature of the BUF04 architecture is the use of
“slew-enhancement” transistors, Q11–Q14. Under normal small
signal (VIN < 2 Vbes) conditions, these transistors are normally
“OFF.” In large signals, high speed transient applications where
the input signal is > 2 Vbes, these transistors turn on and literally
“brute-force” the output to follow the input. When the input
signal drops below 2 Vbes, the transistors return to their
normally “OFF” state.
–9–
BUF04
A two-terminal equivalent circuit of the BUF04 is shown in
Figure 30 where the transistor-level equivalent circuit is reduced
to its essential elements. The input stage develops a signal
current, IIN, that is replicated by an internal current conveyor so
as to flow through Rt, the transimpedance of the BUF04. The
voltage developed across Rt is buffered by a unity-gain output
voltage follower. With an open-loop Rt of 400 kΩ and an RIN of
30 Ω, the voltage gain of the BUF04, given by the ratio Rt/RIN is
approximately 13,000—accurate to approximately 13.5 bits.
The BUF04’s open-loop ac transimpedance response is
determined by the open-loop pole formed by Rt and Ct. Since
Ct is typically 8 pF, the open-loop pole occurs at approximately
50 kHz.
VIN
To minimize the effects of high-frequency coupling, circuits
must be built with short interconnect leads, and large ground
planes should he used whenever possible to provide a low
resistance, low-inductance circuit path. Sockets should be
avoided because the increased interlead capacitance can degrade
bandwidth and stability. If sockets are necessary, individual pin
sockets (oftentimes called “cage jacks,” AMP Part No.
5-330808-3 or 5-330808-6) should be used. They contribute far
less stray reactance than molded socket assemblies.
Offset Voltage Nulling
Although the offset voltage of the BUF04 is very low (1 mV,
maximum) for such a high speed buffer, the circuit shown in
Figure 32 can be used if additional offset voltage nulling is
required. A potentiometer ranging from 1 k to 10 k can be used
for VOS nulling; with a 10 kΩ potentiometer, the trim range is
± 30 mV.
X1
Rt
IIN
Ct
IIN
VOUT
XI
V+
RIN
TRIM RANGE
±30mV
1
RFB
RIN = 30 Ω
Rt = 400 k Ω
Ct = 8pF
RFB = 100 Ω
3
VIN
10µF
0.1µF
10k
8
7
BUF04
VOUT
6
0.1µF
4
Figure 30. Current-Feedback Functional Equivalent
Circuit of the BUF04
10µF
Grounding and Bypassing Considerations
V–
To take full advantage of the BUF04’s very wide bandwidth,
high slew rates, and dynamic range capabilities requires due
diligence with regard to supply bypassing. In high speed circuits,
the supply bypassing network must provide a very low impedance
return path for currents flowing to and from the load network.
As with any high speed application, multiple bypassing is always
recommended. A 10 µF tantalum electrolytic in parallel with a
0.1 µF ceramic capacitor is sufficient for most applications. For
those high speed applications where output load currents
approach 50 mA, small valued resistors (1.1 Ω to 4.7 Ω) in
series with the tantalum capacitors may improve circuit
transient response by damping out the capacitor’s selfinductance. Figure 31 illustrates bypassing recommendations.
Figure 32. Optional Offset Voltage Nulling Scheme
APPLICATIONS
Output Short-Circuit Protection
To optimize the transient response and output voltage swing of
the BUF04, internal output short-circuit current limiting was
omitted. Although the BUF04 can provide continuous output
currents of 50 mA without protection, direct connection of the
BUF04’s output to ground or to the supplies will destroy the
device. An active current limit technique, illustrated in Figure
33, provides the necessary short-circuit protection while
retaining full dc output voltage swing to the load.
+15V
10µF
V+
10µF R1
RSC1
≥10Ω
0.1µF
7
3
VIN
RS
BUF04
2N2905
KELVIN RETURN
FOR LOAD CURRENT
6
2N2905
0.1µF
7
VOUT
VIN
RL
4
3
BUF04
0.1µF
4
10µF
V–
R2
SET ISC +(ISC–) <60mA,
CONTINUOUS
0.6V
RSC1 (RSC2) =
ISC + (ISC–)
6
0.1µF
VOUT
6.2k Ω
0.01µF
2N2219
KELVIN RETURN
FOR LOAD CURRENT
2N2219
RSC2
≥10Ω
NOTE
USE SHORT LEAD LENGTHS (<5mm)
Figure 31. Recommended Power-Supply Bypassing
10µF
–15V
Figure 33. Short-Circuit Current Limiting Using
Current Sources
–10–
REV. 0
BUF04
Output Current Transient Recovery
Settling characteristics of high speed buffers also include the
buffer’s ability to recover, i.e., settle, from a transient output
current load condition. When driving the input of an A/D
converter, especially the successive-approximation converter
types, the buffer must maintain a constant output voltage under
dynamically changing load current conditions. In these types of
converters, the comparison point is usually diode-clamped, but
it may deviate several hundred millivolts resulting in high
frequency modulation of the A/D input current. Open-loop and
closed-loop buffers (also, op amps configured as followers) that
exhibit high closed-loop output impedances and/or low unity
gain crossover frequencies recover very slowly from output load
current transients. This slow recovery leads to linearity errors or
missing codes because of errors in the instantaneous input voltage. Therefore, the buffer (or op amp) chosen for this type of
application should exhibit low output impedance and high unity
gain bandwidth so that its output has had a chance to settle to
its nominal value before the converter makes its comparison.
The circuit in Figure 34 illustrates a settling measurement
circuit for evaluating the recovery time of high speed buffers
from an output load current transient. The input to the buffer is
grounded for ease of measuring the recovery time, and two
resistors are used to sum steady-state and transient load currents
at the output. As a worst-case condition, R1, was chosen such
that the BUF04 would source (or sink) a steady-state current of
25 mA. R2 was then chosen to add a 10 mA transient current
upon the steady-state value. To set accurately the nodal voltages
internal to the BUF04, the supply voltages were offset by the
voltage applied to R1. Because of its high transimpedance, wide
bandwidth, and low output impedance, the BUF04 exhibits an
extremely fast recovery time of 60 ns to 0.01%, as shown in
Figure 34. Results were identical regardless whether the BUF04
was sourcing or sinking current.
V+
10µF
0.1µF
3
BUF04
TP2
TP1
7
6
0.1µF
4
10µF
R2
250Ω
R1
200Ω
VIN
SOURCE: 0➔ –2.5 V
SINK: 0➔ +2.5V
VLOAD
SOURCE: –5V
SINK: +5V
∆t 59.00ns
ISOURCE
100
(4mA/DIV)
90
25mA
35mA
VOUT
(5mV/DIV) 0%
10
100mV
5mV
20ns
Figure 35. BUF04’s Output Load Current Recovery Time
Terminated Line Drivers
The BUF04’s high output current, large slew rate, and wide
bandwidth all combine to make it an ideal device for high speed
line driver applications. As shown in Figure 36, the BUF04 can
be configured for driving doubly terminated 50 Ω and 75 Ω
cables. To optimize the circuit’s pulse response, a capacitor, CT
(CX + CTRIM), is connected across the series back termination.
The BUF04 can drive a 50 Ω line to ± 2.5 V and a 75 Ω line to
± 3.75 V when operating on ± 15 V supplies.
CT
CX
3
VIN
BUF04
6
6'
COAX
RX
RS
ZO
50Ω
75Ω
COAX
RG-58
RG-59
RL
RS, RL
50Ω
75Ω
RX
50
75
CX
91pF
62pF
CT
3–15pF
3–15pF
Figure 36. Line Driver Configuration
Low-Pass Active Filter
In many signal-conditioning applications, filters are required to
band-limit noise or altogether eliminate other unwanted signals
prior to conversion. Often, high frequency filters are needed for
these applications; however, there are few op amps that exhibit
the high open-loop gain and wide unity-gain crossover
frequency required for these applications. As illustrated in
Figure 37, the BUF04 and a handful of passive components can
be configured as a high frequency, low-pass active filter. Since
the filter configuration is a unity-gain Sallen-Key topology, the
BUF04 is particularly well suited for this application. In this
circuit, an additional resistor, R3, was added to prevent
interaction between C2 and the BUF04’s input capacitance.
V–
Figure 34. Transient Output Load Current Test Circuit
C1*
44pF (22pF x 2)
VIN
R1
499Ω
R2
499Ω
R3
47Ω
3
6
BUF04
VOUT
C2*
22pF
* SILVERED MICA OR
DIPPED CERAMIC
WO =
1
R1 · R2 · C1 · C2
;
Q=
C1
4 · C2
Figure 37. A 10 MHz Low-Pass Active Filter
REV. 0
–11–
BUF04
Operation Within an Op Amp Feedback Loop
Paralleling BUF04s for Increased Load Drive Capability
The BUF04 is well suited as a current booster or isolation
buffer within the closed loop of precision op amps such as the
OP177, the OP97, the OP27, or the OP77. Since the BUF04 is
a closed loop voltage buffer, no interstage coupling resistor
between the op amp and the buffer’s input is required for circuit
stability. The wide bandwidth and high slew rate of the BUF04
assure that the loop has the characteristics of the op amp; hence,
no additional rolloff is required.
In applications where continuous output currents greater than
50 mA are required or where heat management is an issue, a
number of BUF04s can be connected in parallel to reduce the
drive requirement of any one buffer. An example of one such
application is illustrated in Figure 39. In this circuit, the
BUF04s are required to drive a doubly terminated 50 Ω line to
± 5 V. This type of a load for a single BUF04 would certainly
cause a power dissipation problem. Parallel operation results in
lower input and output impedances and increased bias currents;
on the other hand, input equivalent noise voltage is reduced and
input offset voltage remains unchanged.
R1
100
R2
2
VIN
3
OP177
6
3
BUF04
6
GAIN
10
100
1000
R1
47Ω
VOUT
RL
500Ω
3
CL
1000pF
R2 (kΩ)
1
10
100
BUF04
6
R3
100Ω
±5V
VIN
±10V
RS
50Ω
R2
47Ω
3
BUF04
6
R4
100Ω
VOUT
RL
50Ω
Figure 38. BUF04 as Booster Stage for a Precision Op Amp
Figure 39. Paralleling BUF04s for High Output Currents
Overdrive Recovery and Phase Reversal
In applications where the inputs could be driven to the supply
rails, the BUF04 recovers in 10 ns from positive or negative
overdrive. The BUF04 does not exhibit any output voltage
phase reversal when the input signal exceeds its input voltage
range.
–12–
REV. 0
BUF04
* BUF04 SPICE Macro-model
7/93, Rev. A
*
JCB / PMI
*
* Copyright 1993 by Analog Devices, Inc.
*
*
* Node assignments
*
noninverting input
*
positive supply
*
negative supply
*
output
*
*
.SUBCKT BUF04 1
99 50 6
*
* INPUT STAGE
*
R1
99
8
200
R2
10
50
200
V1
99
9
4.4
D1
9
8
DX
V2
11
50
4.4
D2
10
11
DX
I1
99
5
1.8E-3
I2
4
50
1.8E-3
Q1
50
3
5
QP
Q2
99
3
4
QN
Q3
8
61
30
QN
Q4
10
7
30
QP
R3
5
61
50E3
R4
4
7
50E3
CP1
61
99
14E-15
CP2
7
50
14E-15
RFB
6
2
100
*
* INPUT ERROR SOURCES
*
IB1
99
1
0.7E-6
VOS
3
1
0.7E-6
LS1
30
2
1E-9
CS1
99
2
2.0E-12
CS2
99
1
3.0E-12
*
EREF 97
0
22 0 1
*
* TRANSCONDUCTANCE STAGE
*
R5
12
97
365E3
C3
12
97
8E-12
G1
97
12
99 8 SE-3
G2
12
97
10 50 SE-3
E3
13
97
POLY(1) 99 97 –2.5 1.1
E4
97
14
POLY(1) 97 50 –2.5 1.1
D3
12
13
DX
D4
14
12
DX
R6
12
15
200
C2
15
6
20E-12
*
REV. 0
* POLE AT 200 MHz
*
R11
20
97
1E6
C7
20
97
0.759E-15
G7
97
20
12 22 1E-6
*
* POLE AT 200 MHz
*
R12
21
97
1E6
C8
21
97
0.759E-15
G8
97
21
20 22 1E-6
*
* OUTPU T STAGE
*
FSY
99
50
POLY(2) V7 V8 1.85E-3 1 1
R13
22
99
16.67E3
R14
22
50
16.67E3
R15
27
99
80
R16
27
50
80
L2
27
6
10E-9
G11
27
99
99 21 12.5E-3
G12
50
27
21 50 12.5E-3
V5
23
27
3.3
V6
27
24
3.3
D5
21
23
DX
D6
24
21
DX
G10
97
70
27 21 12.5E-3
D7
70
71
DX
D8
72
70
DX
V7
71
97
DC 0
V8
97
72
DC 0
*
* MODELS USED
*
.MODEL QN NPN(BF= 1000 IS= 1E-15)
.MODEL QP PNP(BF= 1000 IS= 1E-15)
.MODEL DX D(IS= 1E-15)
.ENDS BUF04
–13–
BUF04
BUF04 SPICE
99
R6
R1
9
D1
I1
IB1
5
CS2
R5
Q3
D4
13
C3
14
E4
97
LS1
30
Q2
3
G2
E3
Q1
VOS
6
D3
G1
61
1
+IN
CS1
12
8
R3
C2
12
V1
CP1
15
R4
7
4
2
Q4
6
10
RFB
D2
I2
CP2
11
R2
V2
50
20
R11
G7
21
C7
G8
R12
C8
97
99
G11
FSY
R13
22
D7
G10
R14
R15
D5 23 V5
70
71
V7
D8
72
V8
21
27
D6 24
L2
V6
6
R16
G12
97
50
–14–
REV. 0
BUF04
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
8-Lead Plastic DIP (N-8)
8
5
0.280 (7.11)
0.240 (6.10)
PIN 1
1
4
0.325 (8.25)
0.300 (7.62)
0.430 (10.92)
0.348 (8.84)
0.015
(0.381) TYP
0.210
(5.33)
MAX
0.130
(3.30)
MIN
0.160 (4.06)
0.115 (2.93)
0.022 (0.558)
0.014 (0.356)
0.100
(2.54)
BSC
0.070 (1.77)
0.045 (1.15)
0.195 (4.95)
0.115 (2.93)
0.015 (0.381)
0.008 (0.204)
SEATING
PLANE
8-Lead Cerdip (Q-8)
0.005 (0.13) MIN
8-Lead Narrow-Body SO (R-8)
0.055 (1.4) MAX
5
8
8
5
0.310 (7.87)
0.220 (5.59)
PIN 1
1
0.320 (8.13)
0.290 (7.37)
0.1968 (5.00)
0.1890 (4.80)
0.060 (1.52)
0.015 (0.38)
0.200 (5.08)
0.125 (3.18)
0.023 (0.58) 0.100 0.070 (1.78)
0.014 (0.36) (2.54) 0.030 (0.76)
BSC
REV. 0
0.2440 (6.20)
0.2284 (5.80)
4
1
4
0.405 (10.29) MAX
0.200
(5.08)
MAX
0.1574 (4.00)
0.1497 (3.80)
PIN 1
0.0098 (0.25)
0.0040 (0.10)
0.150
(3.81)
MIN
0.015 (0.38)
0.008 (0.20)
0.0500
(1.27)
BSC
15°
0°
SEATING
PLANE
–15–
0.0196 (0.50)
x 45°
0.0099 (0.25)
0.102 (2.59)
0.094 (2.39)
0.0192 (0.49)
0.0138 (0.35)
0.0098 (0.25)
0.0075 (0.19)
8°
0°
0.0500 (1.27)
0.0160 (0.41)
PRINTED IN U.S.A.
C1856–10–10/93
BUF04
–16–
REV. 0