a 160 MHz Rail-to-Rail Amplifier with Disable AD8041 FEATURES Fully Specified for +3 V, +5 V, and 65 V Supplies Output Swings Rail to Rail Input Voltage Range Extends 200 mV Below Ground No Phase Reversal with Inputs 1 V Beyond Supplies Disable/Power-Down Capability Low Power of 5.2 mA (26 mW on +5 V) High Speed and Fast Settling on +5 V: 160 MHz –3 dB Bandwidth (G = +1) 160 V/ms Slew Rate 30 ns Settling Time to 0.1% Good Video Specifications (RL = 150 V, G = +2) Gain Flatness of 0.1 dB to 30 MHz 0.03% Differential Gain Error 0.038 Differential Phase Error Low Distortion –69 dBc Worst Harmonic @ 10 MHz Outstanding Load Drive Capability Drives 50 mA 0.5 V from Supply Rails Cap Load Drive of 45 pF APPLICATIONS Power Sensitive High Speed Systems Video Switchers Distribution Amplifiers A/D Driver Professional Cameras CCD Imaging Systems Ultrasound Equipment (Multichannel) Single-Supply Multiplexer PRODUCT DESCRIPTION The AD8041 is a low power voltage feedback, high speed amplifier designed to operate on +3 V, +5 V or ± 5 V supplies. It has true single supply capability with an input voltage range extending 200 mV below the negative rail and within 1 V of the positive rail. CONNECTION DIAGRAM 8-Pin Plastic Mini-DIP and SOIC NC 1 8 DISABLE –INPUT 2 7 +V +INPUT 3 6 OUTPUT –V S 4 S AD8041 (Top View) 5 NC NC = NO CONNECT The output voltage swing extends to within 50 mV of each rail, providing the maximum output dynamic range. Additionally, it features gain flatness of 0.1 dB to 30 MHz while offering differential gain and phase error of 0.03% and 0.03° on a single +5 V supply. This makes the AD8041 ideal for professional video electronics such as cameras, video switchers or any high speed portable equipment. The AD8041’s low distortion and fast settling make it ideal for buffering high speed A-to-D converters. The AD8041 has a high speed disable feature useful for multiplexing or for reducing power consumption (1.5 mA). The disable logic interface is compatible with CMOS or open-collector logic. The AD8041 offers low power supply current of 5.8 mA max and can run on a single +3 V power supply. These features are ideally suited for portable and battery powered applications where size and power are critical. The wide bandwidth of 160 MHz along with 160 V/µs of slew rate on a single +5 V supply make the AD8041 useful in many general purpose high speed applications where dual power supplies of up to ± 6 V and single supplies from +3 V to +12 V are needed. The AD8041 is available in 8-pin plastic DIP and SOIC over the industrial temperature range of –40°C to +85°C. +2 VS = +5V G = +2 RF = 400Ω +1 NORMALIZED GAIN – dB 0 5V 2.5V –1 –2 –3 –4 –5 –6 –7 0V 1V 200ns –8 0 20 40 60 80 100 FREQUENCY – MHz Figure 1. Output Swing: Gain = –1, VS = +5 V Figure 2. Frequency Response: Gain = +2, VS = +5 V REV. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. © Analog Devices, Inc., 1995 One Technology Way, P.O. Box 9106, Norwood. MA 02062-9106, U.S.A. Tel: 617/329-4700 Fax: 617/326-8703 AD8041–SPECIFICATIONS (@ T = +258C, V = +5 V, R = 2 kΩ to 2.5 V, unless otherwise noted) A S L Parameter Conditions Min DYNAMIC PERFORMANCE –3 dB Small Signal Bandwidth, VO < 0.5 V p-p Bandwidth for 0.1 dB Flatness Slew Rate Full Power Response Settling Time to 0.1% Settling Time to 0.01% G = +1 G = +2, RL = 150 Ω G = –1, VO = 2 V Step VO = 2 V p-p G = –1, VO = 2 V Step 130 NOISE/DISTORTION PERFORMANCE Total Harmonic Distortion Input Voltage Noise Input Current Noise Differential Gain Error (NTSC) Differential Phase Error (NTSC) AD8041A Typ 130 fC = 5 MHz, VO = 2 V p-p, G = +2, RL = 1 kΩ f = 10 kHz f = 10 kHz G = +2, RL = 150 Ω to 2.5 V G = +2, RL = 150 Ω to 2.5 V G = +2, RL = 75 Ω to 2.5 V G = +2, RL = 75 Ω to 2.5 V DC PERFORMANCE Input Offset Voltage MHz MHz V/µs MHz ns ns –72 16 600 0.03 0.03 0.01 0.19 dB nV/√Hz fA/√Hz % Degrees % Degrees 2 10 1.2 TMIN–TMAX Input Offset Current Open-Loop Gain INPUT CHARACTERISTICS Input Resistance Input Capacitance Input Common-Mode Voltage Range Common-Mode Rejection Ratio OUTPUT CHARACTERISTICS Output Voltage Swing: RL = 10 kΩ Output Voltage Swing: RL = 1 kΩ Output Voltage Swing: RL = 50 Ω Output Current Short Circuit Current Capacitive Load Drive POWER SUPPLY Operating Range Quiescent Current Quiescent Current (Disabled) Power Supply Rejection Ratio DISABLE CHARACTERISTICS Turn-Off Time Turn-On Time Off Isolation (Pin 8 Tied to –VS) Off Voltage (Device Disabled) On Voltage (Device Enabled) RL = 1 kΩ TMIN –TMAX 86 VCM = 0 V to 3.5 V 74 0.35 to 4.75 0.4 to 4.4 VOUT = 0.5 V to 4.5 V Sourcing Sinking G = +1 0.2 95 90 VO = 2 V p-p @ 10 MHz, G = + 2 RF = RL = 2 kΩ RF = RL = 2 kΩ RL = 100 Ω, f = 5 MHz, G = +2, RF = 1 kΩ 72 7 8 2 3 0.5 mV mV µV/°C µA µA µA dB dB 160 1.8 –0.2 to 4 80 kΩ pF V dB 0.05 to 4.95 0.1 to 4.9 0.3 to 4.5 50 90 150 45 V V V mA mA mA pF 3 VS = 0, +5 V, ± 1 V Units 160 30 160 24 35 55 TMIN–TMAX Offset Drift Input Bias Current Max 5.2 1.4 80 120 230 70 <+VS – 0.25 Open or +VS 12 5.8 1.7 V mA mA dB ns ns dB V V Specifications subject to change without notice. –2– REV. 0 AD8041 SPECIFICATIONS (@ T = +258C, V = +3 V, R = 2 kΩ to 1.5 V, unless otherwise noted) A S L Parameter Conditions Min DYNAMIC PERFORMANCE –3 dB Small Signal Bandwidth, VO < 0.5 V p-p Bandwidth for 0.1 dB Flatness Slew Rate Full Power Response Settling Time to 0.1% Settling Time to 0.01% G = +1 G = +2, RL = 150 Ω G = –1, VO = 2 V Step VO = 2 V p-p G = –1, VO = 2 V Step 120 NOISE/DISTORTION PERFORMANCE Total Harmonic Distortion Input Voltage Noise Input Current Noise Differential Gain Error (NTSC) Differential Phase Error (NTSC) AD8041A Typ 120 fC = 5 MHz, VO = 2 V p-p, G = –1, RL = 100 Ω f = 10 kHz f = 10 kHz G = +2, RL = 150 Ω to 1.5 V, Input VCM = 1 V G = +2, RL = 150 Ω to 1.5 V, Input VCM = 1 V DC PERFORMANCE Input Offset Voltage MHz MHz V/µs MHz ns ns –55 16 600 0.07 0.05 dB nV/√Hz fA/√Hz % Degrees 2 10 1.2 TMIN –TMAX Input Offset Current Open-Loop Gain INPUT CHARACTERISTICS Input Resistance Input Capacitance Input Common-Mode Voltage Range Common-Mode Rejection Ratio OUTPUT CHARACTERISTICS Output Voltage Swing: RL = 10 kΩ Output Voltage Swing: RL = 1 kΩ Output Voltage Swing: RL = 50 Ω Output Current Short Circuit Current Capacitive Load Drive POWER SUPPLY Operating Range Quiescent Current Quiescent Current (Disabled) Power Supply Rejection Ratio DISABLE CHARACTERISTICS Turn-Off Time Turn-On Time Off Isolation (Pin 8 Tied to –VS) Off Voltage (Device Disabled) On Voltage (Device Enabled) RL = 1 kΩ TMIN –TMAX 85 VCM = 0 V to 1.5 V 0.45 to 2.7 0.5 to 2.6 VOUT = 0.5 V to 2.5 V Sourcing Sinking G = +1 0.2 94 89 VS = 0, +3 V, ± 0.5 V VO = 2 V p-p @ 10 MHz, G = +2 RF = RL = 2 kΩ RF = RL = 2 kΩ RL = 100 Ω, f = 5 MHz, G = +2, RF = 1 kΩ –3– 68 7 8 2.3 3 0.6 mV mV µV/°C µA µA µA dB dB 160 1.8 –0.2 to 2 80 kΩ pF V dB 0.05 to 2.95 0.1 to 2.9 0.25 to 2.75 50 70 120 40 V V V mA mA mA pF 3 Specifications subject to change without notice. REV. 0 72 Units 150 25 150 20 40 55 TMIN –TMAX Offset Drift Input Bias Current Max 5.0 1.3 80 90 170 70 <+VS – 0.25 Open or +VS 12 5.6 1.5 V mA mA dB ns ns dB V V AD8041–SPECIFICATIONS (@ T = +258C, V = 65 V, R = 2 kΩ to 0 V, unless otherwise noted) A S L Parameter Conditions Min DYNAMIC PERFORMANCE –3 dB Small Signal Bandwidth, VO < 0.5 V p-p Bandwidth for 0.1 dB Flatness Slew Rate Full Power Response Settling Time to 0.1% Settling Time to 0.01% G = +1 G = +2, RL = 150 Ω G = –1, VO = 2 V Step VO = 2 V p-p G = –1, VO = 2 V Step 140 NOISE/DISTORTION PERFORMANCE Total Harmonic Distortion Input Voltage Noise Input Current Noise Differential Gain Error (NTSC) Differential Phase Error (NTSC) AD8041A Typ 140 fC = 5 MHz, VO = 2 V p-p, G = +2, RL = 1 kΩ f = 10 kHz f = 10 kHz G = +2, RL = 150 Ω G = +2, RL = 150 Ω G = +2, RL = 75 Ω G = +2, RL = 75 Ω DC PERFORMANCE Input Offset Voltage MHz MHz V/µs MHz ns ns –77 16 600 0.02 0.03 0.02 0.10 dB nV/√Hz fA/√Hz % Degrees % Degrees 2 10 1.2 TMIN –TMAX Input Offset Current Open-Loop Gain INPUT CHARACTERISTICS Input Resistance Input Capacitance Input Common-Mode Voltage Range Common-Mode Rejection Ratio OUTPUT CHARACTERISTICS Output Voltage Swing: RL = 10 kΩ Output Voltage Swing: RL = 1 kΩ Output Voltage Swing: RL = 50 Ω Output Current Short Circuit Current Capacitive Load Drive POWER SUPPLY Operating Range Quiescent Current Quiescent Current (Disabled) Power Supply Rejection Ratio DISABLE CHARACTERISTICS Turn-Off Time Turn-On Time Off Isolation (Pin 8 Tied to –VS) Off Voltage (Device Disabled) On Voltage (Device Enabled) RL = 1 kΩ TMIN –TMAX 90 VCM = –5 V to 3.5 V 72 –4.45 to +4.6 –4.3 to +3.2 VOUT = –4.5 V to 4.5 V Sourcing Sinking G = +1 0.2 99 95 VO = 2 V p-p @ 10 MHz, G = +2 RF = 2 kΩ RF = 2 kΩ RL = 100 Ω, f = 5 MHz, G = +2, RF = 1 kΩ 68 7 8 2.3 3 0.6 mV mV µV/°C µA µA µA dB dB 160 1.8 –5.2 to 4 80 kΩ pF V dB –4.95 to +4.95 –4.8 to +4.8 –4.5 to +3.8 50 100 160 50 V V V mA mA mA pF 3 VS = –5, +5 V, ± 1 V Units 170 32 170 26 30 50 TMIN –TMAX Offset Drift Input Bias Current Max 5.8 1.6 80 12 6.5 2.2 120 320 70 <+VS – 0.25 V Open or +VS V mA mA dB ns ns dB Specifications subject to change without notice. –4– REV. 0 AD8041 ABSOLUTE MAXIMUM RATINGS 1 MAXIMUM POWER DISSIPATION Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +12.6 V Internal Power Dissipation2 Plastic Package (N) . . . . . . . . . . . . . . . . . . . . . . . 1.3 Watts Small Outline Package (R) . . . . . . . . . . . . . . . . . . 0.9 Watts Input Voltage (Common Mode) . . . . . . . . . . . . . . . . . . . . ± VS Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . ± 3.4 V Output Short Circuit Duration . . . . . . . . . . . . . . . . . . . . . . Observe Power Derating Curves Storage Temperature Range N, R . . . . . . . . –65°C to +125°C Operating Temperature Range (A Grade) . . . –40°C to +85°C Lead Temperature Range (Soldering 10 sec) . . . . . . . . +300°C The maximum power that can be safely dissipated by the AD8041 is limited by the associated rise in junction temperature. The maximum safe junction temperature for plastic encapsulated devices is determined by the glass transition temperature of the plastic, approximately +150°C. Exceeding this limit temporarily may cause a shift in parametric performance due to a change in the stresses exerted on the die by the package. Exceeding a junction temperature of +175°C for an extended period can result in device failure. While the AD8041 is internally short circuit protected, this may not be sufficient to guarantee that the maximum junction temperature (+150°C) is not exceeded under all conditions. To ensure proper operation, it is necessary to observe the maximum power derating curves. NOTES 1 Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2 Specification is for the device in free air: 8-Pin Plastic Package: θJA = 90°C/Watt 8-Pin SOIC Package: θJA = 160°C/Watt. MAXIMUM POWER DISSIPATION – Watts 2.0 ORDERING GUIDE Model AD8041AN AD8041AR AD8041AR-REEL AD8041-EB Temperature Range Package Option –40°C to +85°C –40°C to +85°C 8-Pin Plastic DIP 8-Pin Plastic SOIC REEL-SOIC Evaluation Board 8-PIN MINI-DIP PACKAGE TJ = +150°C 1.5 1.0 8-PIN SOIC PACKAGE 0.5 0 –50 –40 –30 –20 –10 0 10 20 30 40 50 60 AMBIENT TEMPERATURE – °C 70 80 90 Figure 3. Maximum Power Dissipation vs. Temperature CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD8041 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. REV. 0 –5– WARNING! ESD SENSITIVE DEVICE AD8041–Typical Performance Characteristics 30 100 VS = ±2.5V T = +25°C 91 PARTS MEAN = +0.21 STD DEVIATION = 1.47 95 OPEN-LOOP GAIN – dB NUMBER OF PARTS IN BIN 25 20 15 10 90 85 VS = +5V T = +25°C 80 5 0 75 –6 –5 –4 –3 –2 –1 0 1 VOS – mV 2 3 4 5 70 6 250 500 750 1000 1250 1500 LOAD RESISTANCE – Ω 1750 2000 Figure 7. Open-Loop Gain vs. RL to +25 °C Figure 4. Typical Distribution of VOS 100 0.20 MEAN = 0.02µV/°C STD DEV = 2.87µV/°C SAMPLE SIZE = 45 97 0.15 OPEN-LOOP GAIN – dB PROBABILITY DENSITY 0 0.10 0.05 94 VS = +5V RL = 1kΩ TO +2.5V 91 88 0 –10 –7.5 –5 –2.5 0 2.5 5 85 –60 10 7.5 –40 –20 VOS DRIFT – µV/°C Figure 5. VOS Drift Over –40 °C to +85 °C 20 40 60 TEMPERATURE – °C 80 100 120 Figure 8. Open-Loop Gain vs. Temperature 100 2 VS = +5V RL = 500Ω TO +2.5V VS = +5V VCM = 0V 90 1.5 OPEN-LOOP GAIN – dB INPUT BIAS CURRENT – µA 0 1 80 RL = 50Ω TO +2.5V 70 60 0.5 50 0 –45 –35 –25 –15 –5 40 5 15 25 35 45 TEMPERATURE – °C 55 65 75 0 85 0.5 1 1.5 2 2.5 3 3.5 OUTPUT VOLTAGE – Volts 4 4.5 5 Figure 9. Open-Loop Gain vs. Output Voltage Figure 6. IB vs. Temperature –6– REV. 0 AD8041 INPUT VOLTAAGE NOISE – nV/ √Hz 200 150 100 50 0 10 1k FREQUENCY – Hz 100 10k 100k Figure 10. Input Voltage Noise vs. Frequency Figure 13. Differential Gain and Phase Errors 6.5 VS = +3V, AV = –1, RL = 100Ω TO 1.5V –40 6.4 VS= +5V G = +2 RL = 150Ω TO 2.5V RF = 402Ω 6.3 CLOSED-LOOP GAIN – dB TOTAL HARMONIC DISTORTION – dBc –30 VS = +5V, AV = +2, RL = 100Ω TO 2.5V –50 –60 VS = +5V, AV = +1, RL = 100Ω TO 2.5V –70 –80 VS = +5V, AV = +2, RL = 1kΩ TO 2.5V –90 6.1 6.0 32.4MHz 5.9 5.8 5.7 VS = +5V, AV = +1, RL = 1kΩ TO 2.5V –100 1 6.2 5.6 5.5 3 4 5 6 2 FUNDAMENTAL FREQUENCY – MHz 7 8 9 10 1 10 FREQUENCY – MHz 100 500 Figure 14. 0.1 dB Gain Flatness Figure 11. Total Harmonic Distortion –30 +180 +120 10MHz –40 VS = +5V RL = 2kΩ TO +2.5V CL = 5pF TO +2.5V OPEN-LOOP GAIN – dB WORST HARMONIC – dBc 5MHz –60 –70 –80 1MHz –90 –100 –110 VS = +5V RL = 2kΩ TO +2.5V GAIN = +2 –120 –140 0 0.5 1 2.5 1.5 2 3 3.5 OUTPUT VOLTAGE – VPP 4 4.5 Figure 12. Worst Harmonic vs. Output Voltage 90 0 +40 PHASE +20 –45 0 –90 –40 0.0 5 +135 45 +60 –135 –20 –130 REV. 0 +80 GAIN 0.1 1 10 FREQUENCY – MHz 100 –180 500 Figure 15. Open-Loop Gain and Phase Margin vs. Frequency –7– PHASE MARGIN – Degrees +100 –50 AD8041–Typical Performance Characteristics 5 50 VS= +5V RL = 2kΩ TO 2.5V CL= 5pF G =+1 4 CLOSED-LOOP GAIN – dB 3 G = –1 T = +125°C VS = +3V, 0.1% 40 T = +25°C 2 0 TIME – ns 1 T = –55°C –1 VS = ±5V, 0.1% 30 VS = +3V, 1% –2 20 –3 VS = ±5V, 1% –4 –5 1 10 FREQUENCY – MHz 100 10 0.5 500 Figure 16. Closed-Loop Frequency Response vs. Temperature –10 GAIN = +1 RL = 2kΩ CL= 5pF 4 3 –20 VS = +3V RL & CL TO 1.5V VS = +5V RL & CL TO 2.5V 2 –40 1 0 VS = +3V AND ±5V –30 CMRR – dB CLOSED-LOOP GAIN – dB 2 Figure 19. Settling Time vs. Input Step 5 VS = ±5V –1 –50 –60 –70 –80 –2 –3 –90 –4 –100 –5 1 1.5 INPUT STEP – Volts p-p 1 10 FREQUENCY – MHz 100 –110 0.01 500 0.1 1 10 FREQUENCY – MHz 100 500 Figure 20. CMRR vs. Frequency Figure 17. Closed-Loop Frequency Response vs. Supply 0.60 OUTPUT SATURATION VOLTAGE – Volts 100 OUTPUT RESISTANCE – Ω GAIN = +1 VS = +5V 10 1 0.1 0.01 VS = +5V 0.50 °C 25 +1 H, 0.40 V +5 – VO °C , H – VO 0.30 +5V 0.20 V OL, – –55 5°C +12 V OL, 55°C 0.10 0 0.01 0.1 1 10 FREQUENCY – MHz 100 0 500 Figure 18. Output Resistance vs. Frequency 5 10 15 20 25 30 35 LOAD CURRENT – mA 40 45 50 Figure 21. Output Saturation Voltage vs. Load Current –8– REV. 0 AD8041 8 90 100kΩ 80 1kΩ VS = +5V RSERIES 70 CAPACITIVE LOAD – pF SUPPLY CURRENT – mA 7 VS = ±5V 6 VS = +5V 5 VS = +3V 4 CLOAD VIN 60 50 20° PHASE MARGIN 40 45° PHASE MARGIN 30 20 3 10 2 –60 –40 –20 0 20 40 60 80 100 0 120 0 20 30 40 SERIES RESISTANCE – Ω 10 TEMPERATURE – °C 5 40 4 20 VS = +5V RL = 5KΩ TO +2.5V RF = 2kΩ VS = +5V 3 –20 NORMALIZED OUTPUT (DB) 0 PSRR – dB 60 Figure 25. Capacitive Load vs. Series Resistance Figure 22. Supply Current vs. Temperature –PSRR –40 –60 +PSRR –80 –100 –120 –140 –160 0.01 50 G = +2 2 1 0 –1 G = +5 –2 G = +10 G = +2, RL = 402Ω –3 –4 0.1 1 10 FREQUENCY – MHz 100 –5 1M 500 10M FREQUENCY – Hz 100M 500M Figure 26. Frequency Response vs. Closed-Loop Gain Figure 23. PSRR vs. Frequency 10 1.600V 9 VS = ±5V RL = 2kΩ VOUT p-p – Volts 7 1.550V 6 G = +1 1.525V 5 1.500V 4 1.475V 3 1.450V 2 1.425V 1 0 0.1 50mV 10ns 1.400V 1 10 FREQUENCY – MHz 100 1000 Figure 24. Output Voltage Swing vs. Frequency REV. 0 VIN = 0.1V p-p RL = 2kΩ VS = +3V 1.575V 8 Figure 27. Pulse Response, VS = +3 V –9– AD8041–Typical Performance Characteristics 5V 4.840V MAX VS = +5V G = +1 RL = 2kΩ VL = 5pF 2.6V 4V RL = 150Ω TO +2.5V 2.55V 3V 2.5V 2V 2.45V 1V 0.111V MIN 2.4V 200µs 1V 50mV 40ns 0V Figure 28a. Figure 30. 100 mV Step Response, VS = +5 V, G = +1 5V 3V 4.741V MAX VIN = 3V p-p f = 0.1MHz RL = 2kΩ VS = +3V G = –1 2.5V 4V RL = 150Ω TO GND 2V 3V 1.5V 2V 1V 1V 0.5V 0.043V MIN 1V 500mV 200µs 0V 2µs 0V Figure 28b. Figure 28a-b. Output Swing vs. Load Reference Voltage, VS = +5 V, G = –1 Figure 31. Output Swing, VS = +3 V, VIN = 3 V p-p 3V 4.5V VS = +5V G = +2 RL = 2kΩ VIN = 1V p-p 3.5V VIN = 2.8V p-p f = 0.8MHz RL = 2kΩ VS = +3V G = –1 2.5V 2V 1.5V 2.5V 1V 1.5V 0.5V 1V 500mV 40ns 2µs 0V 0.5V Figure 32. Output Swing, VS = +3 V, VIN = 2.8 V p-p Figure 29. One Volt Step Response, VS = +5 V, G = +2 –10– REV. 0 AD8041 Overdrive Recovery capacitor C9. R1 is the output resistance of the input stage; gm is the input transconductance. C7 and C9 provide Miller compensation for the overall op amp. The unity gain frequency will occur at gm/C9. Solving the node equations for this circuit yields: Overdrive of an amplifier occurs when the output and/or input range are exceeded. The amplifier must recover from this overdrive condition. As shown in Figure 33, the AD8041 recovers within 50 ns from negative overdrive and within 25 ns from positive overdrive. VOUT = Vi 5V OUTPUT where INPUT 2.5V G = +2 VS = +5V 0V 50mV g (sR1[C9 (A2 + 1)] + 1) × s m2 + 1 C3 A0 = gmgm2 R2 R1 (Open-Loop Gain of Op Amp) A2 = gm2 R2 (Open-Loop Gain of Output Stage) The first pole in the denominator is the dominant pole of the amplifier, and occurs at about 180 Hz. This equals the input stage output impedance R1 multiplied by the Miller-multiplied value of C9. The second pole occurs at the unity-gain bandwidth of the output stage, which is 250 MHz. This type of architecture allows more open-loop gain and output drive to be obtained than a standard two-stage architecture would allow. 40ns Figure 33. Overdrive Recovery Circuit Description The AD8041 is fabricated on Analog Devices’ proprietary eXtra-Fast Complementary Bipolar (XFCB) process which enables the construction of PNP and NPN transistors with similar fTs in the 2 GHz–4 GHz region. The process is dielectrically isolated to eliminate the parasitic and latch-up problems caused by junction isolation. These features allow the construction of high frequency, low distortion amplifiers with low supply currents. This design uses a differential output input stage to maximize bandwidth and headroom (see Figure 34). The smaller signal swings required on the first stage outputs (nodes S1P, S1N) reduce the effect of nonlinear currents due to junction capacitances and improve the distortion performance. With this design harmonic distortion of better than –85 dB @ 1 MHz into 100 Ω with VOUT = 2 V p-p (Gain = +2) on a single 5 volt supply is achieved. The complementary common-emitter design of the output stage provides excellent load drive without the need for emitter followers, thereby improving the output range of the device considerably with respect to conventional op amps. High output drive capability is provided by injecting all output stage predriver currents directly into the bases of the output devices Q8 and Q36. Biasing of Q8 and Q36 is accomplished by I8 and I5, along with a common-mode feedback loop (not shown). This circuit topology allows the AD8041 to drive 50 mA of output current with the outputs within 0.5 V of the supply rails. Output Impedance The low frequency open-loop output impedance of the common emitter output stage used in this design is approximately 6.5 kΩ. While this is significantly higher than a typical emitter follower output stage, when connected with feedback the output impedance is reduced by the open-loop gain of the op amp. With 110 dB of open-loop gain the output impedance is reduced to less than 0.1 Ω. At higher frequencies the output impedance will rise as the open-loop gain of the op amp drops; however, the output also becomes capacitive due to the integrator capacitors C9 and C3. This prevents the output impedance from ever becoming excessively high (see Figure 18), which can cause stability problems when driving capacitive loads. In fact, the AD8041 has excellent cap-load drive capability for a highfrequency op amp. Figure 25 demonstrates that the AD8041 exhibits a 45° margin while driving a 20 pF direct capacitive load. In addition, running the part at higher gains will also improve the capacitive load drive capability of the op amp. On the input side, the device can handle voltages from –0.2 V below the negative rail to within 1.2 V of the positive rail. Exceeding these values will not cause phase reversal; however, the input ESD devices will begin to conduct if the input voltages exceed the rails by greater than 0.5 V. A “Nested Integrator” topology is used in the AD8041 (see small-signal schematic shown in Figure 35). The output stage can be modeled as an ideal op amp with a single-pole response and a unity-gain frequency set by transconductance gm2 and REV. 0 A0 VCC I1 I10 R26 I2 I3 R39 Q4 Q25 Q36 Q5 Q51 I5 Q39 Q23 Q40 R15 R2 Q22 VEE VINP VINN VOUT Q27 C9 SIN Q2 Q11 Q3 C7 C3 Q31 Q21 SIP VEE R23 R27 Q7 Q17 Q13 I9 Q50 R5 Q8 Q24 R21 R3 I7 IB Q47 VCC VEE Figure 34. AD8041 Simplified Schematic –11– AD8041 C9 VS = +5V 100 S1N 90 C3 gmVi R1 R2 VOUT gm2 S1P 10 0% gmVi R1 C7 1V 200ns Figure 37. 2:1 Multiplexer Performance Figure 35. Small Signal Schematic Single Supply A/D Conversion Disable Operation The AD8041 has an active-low disable pin, which can be used to three-state the output of the part and also lower its supply current. If the disable pin is left floating, the part is enabled and will perform normally. If the disable pin is pulled to 2.5 V (min) below the positive supply, output of the AD8041 will be disabled and the nominal supply current will drop to less than 1.6 mA. For best isolation, the disable pin should be pulled to as low a voltage as possible; ideally, the negative supply rail. Figure 38 shows the AD8041 driving the analog inputs of the AD9050 in a dc coupled system with single ended signals. All components are powered from a single +5 V supply. The AD820 is used to offset the ground referenced input signal to the level required by the AD9050. The AD8041 is used to add in the offset with the ground referenced input signal and buffer the input to AD9050. The nominal input range of the AD9050 1000Ω The disable pin on the AD8041 allows it to be configured as an 2:1 mux as shown in Figure 36 and can be used to switch many types of high speed signals. Higher order multiplexers can also be built. The break-before-make switching time is approximately 50 ns to disable the output and 300 ns to enable the output. +5V 0.1µF 1000Ω +5V 3.3V 1000Ω AD820 0.1µF 7 3 AD8041 2 AD9050 9 10µF 50Ω 10 AD8041 2.8V – 3.8V +5V CH0 5MHz +5V 1000Ω VIN –0.5V TO +0.5V 6 G=2 4 Figure 38. 10-Bit, 40 MSPS A/D Conversion 8 330Ω 330Ω 50Ω is +2.8 V and +3.8 V (1 V p-p centered at +3.3 V). This circuit provides 40 MSPS analog-to-digital conversion on just 330 mW of power while delivering 10-bit performance. +5V 0 10µF –10 CH1 10MHz 7 3 2 330Ω –20 AD8041 50Ω 6 –30 G=2 4 8 –40 330Ω F1 = 4.9MHz FUNDAMENTAL = 0.6dB 2nd HARMONIC = 66.9dB 3rd HARMONIC = 74.7dB SNR = 55.2dB NOISE FLOOR = – 86.1dB ENCODE FREQUENCY = 40MHz –50 –60 13 12 11 10 –70 74HC04 –80 –90 Figure 36. 2:1 Multiplexer –100 Figure 39. FFT Output of Circuit in Figure 38 –12– REV. 0 AD8041 APPLICATIONS RGB Buffer Single Supply Composite Video Line Driver Figure 42 shows a schematic of a single supply gain-of-two composite video line driver. Since the sync tips of a composite video signal extend below ground, the input must be ac coupled and shifted positively to provide signal swing during these negative excursions in a single supply configuration. The AD8041 can provide buffering of RGB signals that include ground while operating from a single +3 V or +5 V supply. The signals that drive an RGB monitor are usually supplied by current output DACs that operate from a +5 V only supply. These can triple DACs like the ADV7120 and ADV7122 from Analog Devices or integrated into the graphics controller IC as in most PCs these days. During the horizontal blanking interval the currents output from the DACs go to zero and the RGB signals are pulled to ground via the termination resistors. If more than one RGB monitor is desired, it cannot simply be connected in parallel because it will provide an additional termination. Therefore, buffering must be provided before connecting a second monitor. Since the RGB signals include ground as part of their dynamic output range, it has previously been required to use a dual supply op amp to provide this buffering. In some systems this is the only component that requires a negative supply so it can be quite inconvenient to incorporate this multiple monitor feature. Figure 40 shows a schematic of one channel of a single supply gain-of-two buffer for driving a second RGB monitor. No current is required when the amplifier output is at ground. The termination resistor at the monitor helps pull the output down at low voltage levels. +3V OR +5V 0.1µF 10µF NC R, G OR B 7 3 8 AD8041 75Ω 6 4 2 75Ω 1kΩ 75Ω SECOND RGB MONITOR 1kΩ PRIMARY RGB MONITOR Figure 40. Single Supply RGB Buffer The input is terminated in 75 Ω and ac coupled via CIN to a voltage divider that provides the dc bias point to the input. Setting the optimal bias point requires some understanding of the nature of composite video signals and the video performance of the AD8041. Signals of bounded peak-to-peak amplitude that vary in duty cycle require larger dynamic swing capability than their peak-topeak amplitude after ac coupling. As a worst case, the dynamic signal swing required will approach twice the peak-to-peak value. The two bounding cases are for a duty cycle that is mostly low, but occasionally goes high at a fraction of a percent duty cycle and vice versa. Composite video is not quite this demanding. One bounding extreme is for a signal that is mostly black for an entire frame, but has a white (full intensity), minimum width spike at least once per frame. The other extreme is for a video signal that is full white everywhere. The blanking intervals and sync tips of such a signal will have negative going excursions in compliance with composite video specifications. The combination of horizontal and vertical blanking intervals limit such a signal to being at its highest level (white) for only about 75% of the time. As a result of the duty cycle variations between the two extremes presented above, a 1 V p-p composite video signal that is multiplied by a gain of two requires about 3.2 V p-p of dynamic voltage swing at the output for an op amp to pass a composite video signal of arbitrary duty cycle without distortion. Some circuits use a sync tip clamp along with ac coupling to hold the sync tips at a relatively constant level in order to lower the amount of dynamic signal swing required. However, these circuits can have artifacts like sync tip compression unless they are driven by sources with very low output impedance. Figure 41 is an oscilloscope photo of the circuit in Figure 40 operating from a +3 V supply and driven by the Blue signal of a color bar pattern. Note that the input and output are at ground during the horizontal blanking interval. The RGB signals are specified to output a maximum of 700 mV peak. The output of the AD8041 is 1.4 V with the termination resistors providing a divide-by-two. The Red and Green signals can be buffered in the same manner with duplication of this circuit. +5V 4.99kΩ 4.99kΩ 10µF 47µF COMPOSITE VIDEO IN 75Ω 6 5µs VIN RT 75Ω 8 4 NC 500mV 75Ω COAX 1000µF AD8041 2 VOUT RL 75Ω 0.1µF RF 1kΩ RG 1kΩ 100 10µF 7 3 10kΩ 0.1µF 220µF 90 GND Figure 42. Single Supply Composite Video Line Driver VOUT GND 10 0% 500mV The AD8041 not only has ample signal swing capability to handle the dynamic range required without using a sync tip clamp, but also has good video specifications like differential gain and differential phase when buffering these signals in an ac coupled configuration. Figure 41. +3 V, RGB Buffer REV. 0 –13– AD8041 To test this, the differential gain and differential phase were measured for the AD8041 while the supplies were varied. As the lower supply is raised to approach the video signal, the first effect to be observed is that the sync tips become compressed before the differential gain and differential phase are adversely affected. Thus, there must be adequate swing in the negative direction to pass the sync tips without compression. Referring to Figure 44, the Green plus sync signal is output from an ADV7120, a single supply triple video DAC. Because the DAC is single supply, the lowest level of the sync tip is at ground or slightly above. The AD8041 is set for a gain of two to compensate for the divide by two of the output terminations. 500mV As the upper supply is lowered to approach the video, the differential gain and differential phase were not significantly adversely affected until the difference between the peak video output and the supply reached 0.6 V. Thus, the highest video level should be kept at least 0.6 V below the positive supply rail. 90 Taking the above into account, it was found that the optimal point to bias the noninverting input is at 2.2 V dc. Operating at this point, the worst case differential gain is measured at 0.06% and the worst case differential phase is 0.06°. 10 0% 500mV The ac coupling capacitors used in the circuit at first glance appear quite large. A composite video signal has a lower frequency band edge of 30 Hz. The resistances at the various ac coupling points—especially at the output—are quite small. In order to minimize phase shifts and baseline tilt, the large value capacitors are required. For video system performance that is not to be of the highest quality, the value of these capacitors can be reduced by a factor of up to five with only a slightly observable change in the picture quality. Sync Stripper Some RGB monitor systems use only three cables total and carry the synchronizing signals along with the Green (G) signal on the same cable. The sync signals are pulses that go in the negative direction from the blanking level of the G signal. In some applications like prior to digitizing component video signals with A/D converters, it is desirable to remove or strip the sync portion from the G signal. Figure 43 is a schematic of a circuit using the AD8041 running on a single +5 V supply that performs this function. GREEN W/SYNC GREEN W/OUT SYNC +5V VBLANK +0.4 GROUND 0.1µF GROUND 7 3 VIN 75Ω AD8041 75Ω 10µF 2 6 4 75Ω (MONITOR) R1 1kΩ 10µs 100 Figure 44. Single Supply Sync Stripper The reference voltage for R1 should be twice the dc blanking level of the G signal. If the blanking level is at ground and the sync tip is negative as in some dual supply systems, then R1 can be tied to ground. In either case, the output will have the sync removed and have the blanking level at ground. Layout Considerations The specified high speed performance of the AD8041 requires careful attention to board layout and component selection. Proper RF design techniques and low-pass parasitic component selection are necessary. The PCB should have a ground plane covering all unused portions of the component side of the board to provide a low impedance path. The ground plane should be removed from the area near the input pins to reduce the stray capacitance. Chip capacitors should be used for the supply bypassing (see Figure 45). One end should be connected to the ground plane and the other within 1/8 inch of each power pin. An additional large (0.47 µF–10 µF) tantalum electrolytic capacitor should be connected in parallel, but not necessarily so close, to supply current for fast, large signal changes at the output. The feedback resistor should be located close to the inverting input pin in order to keep the stray capacitance at this node to a minimum. Capacitance variations of less than 1 pF at the inverting input will significantly affect high speed performance. Stripline design techniques should be used for long signal traces (greater than about 1 inch). These should be designed with a characteristic impedance of 50 Ω or 75 Ω and be properly terminated at each end. R2 1kΩ 0.8V (2X VBLANK) Figure 43. Single Supply Sync Stripper –14– REV. 0 AD8041 Table I. Recommended Component Values Evaluation Board An evaluation board for the AD8041 is available which has been carefully laid out and tested to demonstrate that the specified high speed performance of the device can be realized. For ordering information, please refer to the ordering guide. The layout of the evaluation board can be used as shown or serve as a guide for a board layout. Component +1 RF RG RO (Nominal) RT (Nominal) Small Signal BW (MHz) VS = +5 V 0.1 dB Bandwidth (MHz) VS = +5 V 0Ω AD8041A Gain +2 +2 +5 +10 75 Ω 75 Ω 2 kΩ 2 kΩ 75 Ω 75 Ω 400 Ω 400 Ω 75 Ω 75 Ω 2 kΩ 500 Ω 75 Ω 75 Ω 2 kΩ 220 Ω 75 Ω 75 Ω 160 67 72 20 9 7 32 Figure 45. Noninverting Configurations for Evaluation Boards Figure 47. Board Layout (Component Side) Figure 48. Board Layout (Back Side) Figure 46. Evaluation Board Silkscreen (Top) REV. 0 –15– AD8041 OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 8 C2050–10–7/95 8-Lead Plastic DIP (N-8) 5 0.25 (6.35) PIN 1 1 0.31 (7.87) 4 0.30 (7.62) REF 0.39 (9.91) MAX 0.035±0.01 (0.89±0.25) 0.165±0.01 (4.19±0.25) 0.011±0.003 (0.28±0.08) 0.18±0.03 (4.57±0.76) 0.125 (3.18) MIN 0.018±0.003 (0.46±0.08) 0.10 (2.54) BSC 0.033 (0.84) NOM 15 ° 0° SEATING PLANE 8-Lead Plastic SOIC (SO-8) 5 8 0.1574 (4.00) 0.1497 (3.80) PIN 1 0.2440 (6.20) 0.2284 (5.80) 4 1 0.1968 (5.00) 0.1890 (4.80) 0.0196 (0.50) 0.0099 (0.25) x 45° 0.0688 (1.75) 0.0532 (1.35) 0.0500 (1.27) BSC 0.0192 (0.49) 0.0138 (0.35) 0.0098 (0.25) 0.0075 (0.19) 8° 0° 0.0500 (1.27) 0.0160 (0.41) PRINTED IN U.S.A. 0.0098 (0.25) 0.0040 (0.10) –16– REV. 0