AD ADA4922

High Voltage, Differential
18-Bit ADC Driver
ADA4922-1
FEATURES
FUNCTIONAL BLOCK DIAGRAM
ADA4922-1
1
8
IN
REF
2
7
DIS
VS+
3
6
VS–
OUT+
4
5
OUT–
05681-001
NC
NC = NO CONNECT
Figure 1.
–84
–87
SECOND HARMONIC
THIRD HARMONIC
RL = 2kΩ
–90
–93
DISTORTION (dBc)
Single-ended-to-differential conversion
Low distortion (VO, dm = 40 V p-p)
−99 dBc HD at 100 kHz
Low differential output referred noise: 12 nV/√Hz
High input impedance: 11 MΩ
Fixed gain of 2
No external gain components required
Low output-referred offset voltage: 1.1 mV max
Low input bias current: 3.5 μA max
Wide supply range
5 V to 26 V
Can produce differential output signals in excess of 40 V p-p
High speed
38 MHz, −3 dB bandwidth @ 0.2 V p-p differential output
Fast settling time
200 ns to 0.01% for 12 V step on ±5 V supplies
Disable feature
Available in space-saving, thermally enhanced packages
3 mm × 3 mm LFCSP
8-lead SOIC_EP
Low supply current: IS = 10 mA on ±12 V supplies
–96
VS = ±5V, VO, dm = 12V p-p
–99
–102
–105
–108
–111
High voltage data acquisition systems
Industrial instrumentation
Spectrum analysis
ATE
Medical instruments
–114
VS = ±12V, VO, dm = 40V p-p
–117
–120
1
10
05681-012
APPLICATIONS
100
FREQUENCY (kHz)
Figure 2. Harmonic Distortion for Various Power Supplies
GENERAL DESCRIPTION
The ADA4922-1 is a differential driver for 16-bit to 18-bit
ADCs that have differential input ranges up to ±20 V.
Configured as an easy-to-use, single-ended-to-differential
amplifier, the ADA4922-1 requires no external components to
drive ADCs. The ADA4922-1 provides essential benefits such as
low distortion and high SNR that are required for driving ADCs
with resolutions up to 18 bits.
With a wide supply voltage range (5 V to 26 V), high input
impedance, and fixed differential gain of 2, the ADA4922-1 is
designed to drive ADCs found to in a variety of applications,
including industrial instrumentation.
The ADA4922-1 is manufactured on ADI’s proprietary secondgeneration XFCB process that enables the amplifier to achieve
excellent noise and distortion performance on high supply
voltages.
The ADA4922-1 is available in an 8-lead 3 mm × 3 mm LFCSP
as well as an 8-lead SOIC package. Both packages are equipped
with an exposed paddle for more efficient heat transfer. The
ADA4922-1 is rated to work over the extended industrial
temperature range, −40°C to +85°C.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
© 2005 Analog Devices, Inc. All rights reserved.
ADA4922-1
TABLE OF CONTENTS
Features .............................................................................................. 1
Theory of Operation ...................................................................... 14
Applications....................................................................................... 1
Applications..................................................................................... 16
Functional Block Diagram .............................................................. 1
ADA4922-1 Differential Output Noise Model .......................... 16
General Description ......................................................................... 1
Using the REF Pin ...................................................................... 16
Revision History ............................................................................... 2
Internal Feedback Network Power Dissipation...................... 17
Specifications..................................................................................... 3
Disable Feature ........................................................................... 17
Absolute Maximum Ratings............................................................ 5
Driving a Differential Input ADC............................................ 17
Thermal Resistance ...................................................................... 5
Printed Circuit Board Layout Considerations ....................... 18
ESD Caution.................................................................................. 5
Outline Dimensions ....................................................................... 19
Pin Configuration and Function Descriptions............................. 6
Ordering Guide .......................................................................... 20
Typical Performance Characteristics ............................................. 7
REVISION HISTORY
10/05—Revision 0: Initial Version
Rev. 0 | Page 2 of 20
ADA4922-1
SPECIFICATIONS
VS = ±12 V, TA = 25°C, RL = 1 kΩ, DIS = HIGH, CL = 3 pF, unless otherwise noted.
Table 1.
Parameter
DYNAMIC PERFORMANCE
–3 dB Bandwidth
Overdrive Recovery Time
Slew Rate
Settling Time to 0.01%
NOISE/DISTORTION PERFORMANCE
Harmonic Distortion
Differential Output Voltage Noise
Input Current Noise
DC PERFORMANCE
Differential Output Offset Voltage
Differential Output Offset Voltage Drift
Input Bias Current
Gain
Gain Error
Gain Error Drift
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Voltage Range
OUTPUT CHARACTERISTICS
Output Voltage Swing
DC Output Current
Capacitive Load Drive
POWER SUPPLY
Operating Range
Quiescent Current
Quiescent Current (Disabled)
Power Supply Rejection Ratio (PSRR)
−PSRR
+PSRR
DISABLE
DIS Input Voltage Threshold
Turn-Off Time
Turn-On Time
DIS Bias Current
Enabled
Disabled
Conditions
Min
Typ
G = +2, VO = 0.2 V p-p, differential
G = +2, VO = 40 V p-p, differential
VS+ + 0.5 V to VS− − 0.5 V; +Recovery/−Recovery
VO, dm = 2 V step
VO, dm = 40 V step
VO, dm = 40 V step
34
6.5
38
7.2
180/330
260
730
580
MHz
MHz
ns
V/μs
V/μs
ns
−116/−109
−99/−100
12
1.4
dBc
dBc
nV/√Hz
pA/√Hz
fC = 5 kHz, VO = 40 V p-p, RL = 2 kΩ, HD2/HD3
fC = 100 kHz, VO = 40 V p-p, RL = 2 kΩ, HD2/HD3
f = 100 kHz
f = 100 kHz
0.35
14
1.8
2
−0.05
0.0002
Each single-ended output, RL = 1 kΩ
±10.65
30% overshoot
Max
1.1
3.5
Unit
mV
μV/°C
μA
V/V
%
%/°C
11
1
±10.7
MΩ
pF
V
±10.7
40
20
V
mA
pF
5
9.4
1.5
26
10.1
2.0
V
mA
mA
−89
−91
−80
−83
dB
dB
Disabled
Enabled
≤ −11
≥ −9
160
78
V
V
μs
ns
DIS = −9 V
DIS = −11 V
114
−125
μA
μA
Rev. 0 | Page 3 of 20
ADA4922-1
VS = ±5 V, TA = 25°C, RL = 1 kΩ, DIS = HIGH, CL = 3 pF, unless otherwise noted.
Table 2.
Parameter
DYNAMIC PERFORMANCE
–3 dB Bandwidth
Overdrive Recovery Time
Slew Rate
Settling Time to 0.01%
NOISE/DISTORTION PERFORMANCE
Harmonic Distortion
Differential Output Voltage Noise
Input Current Noise
DC PERFORMANCE
Differential Output Offset Voltage
Differential Output Offset Voltage Drift
Input Bias Current
Gain
Gain Error
Gain Error Drift
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Voltage Range
OUTPUT CHARACTERISTICS
Output Voltage Swing
DC Output Current
Capacitive Load Drive
POWER SUPPLY
Operating Range
Quiescent Current
Quiescent Current (Disabled)
Power Supply Rejection Ratio (PSRR)
−PSRR
+PSRR
DISABLE
DIS Input Voltage
Turn-Off Time
Turn-On Time
DIS Bias Current
Enabled
Disabled
Conditions
Min
Typ
G = +2, VO = 0.2 V p-p, differential
G = +2, VO = 12 V p-p, differential
+Recovery/−Recovery
VO, dm = 2 V step
VO, dm = 12 V step
VO, dm = 12 V step
36
6.5
40.5
13.5
200/670
220
350
200
MHz
MHz
ns
V/μs
V/μs
ns
−102/−108
−101/−98
12
1.4
dBc
dBc
nV/√Hz
pA/√Hz
fC = 5 kHz, VO = 12 V p-p, RL = 2 kΩ, HD2/HD3
fC = 100 kHz, VO = 12 V p-p, RL = 2 kΩ, HD2/HD3
f = 100 kHz
f = 100 kHz
0.4
12
2.0
2
−0.05
0.0002
Each single-ended output, RL = 1 kΩ
±3.55
30% overshoot
Max
1.2
3.5
Unit
mV
μV/°C
μA
V/V
%
%/°C
11
1
±3.6
MΩ
pF
V
±3.6
40
20
V
mA
pF
5
7.0
0.7
26
7.6
1.6
V
mA
mA
−93
−91
−82
−83
dB
dB
Disabled
Enabled
≤ −4
≥ −2
160
78
V
V
μs
ns
DIS = −2 V
DIS = −4 V
41
49
μA
μA
Rev. 0 | Page 4 of 20
ADA4922-1
ABSOLUTE MAXIMUM RATINGS
Rating
26 V
See Figure 3
–65°C to +125°C
–40°C to +85°C
300°C
150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL RESISTANCE
θJA is specified for the worst-case conditions, that is, θJA is
specified for a device soldered in the circuit board with its
exposed paddle soldered to a pad on the PCB surface that is
thermally connected to a copper plane, with zero airflow.
Table 4. Thermal Resistance
Package Type
8-Lead SOIC with EP on 4-layer board
8-Lead LFCSP with EP on 4-layer board
θJA
79
81
θJC
25
17
Unit
°C/W
°C/W
Maximum Power Dissipation
The maximum safe power dissipation in the ADA4922-1
package is limited by the associated rise in junction temperature
(TJ) on the die. At approximately 150°C, which is the glass
transition temperature, the plastic changes its properties. Even
temporarily exceeding this temperature limit can change the
stresses that the package exerts on the die, permanently shifting
the parametric performance of the ADA4922-1. Exceeding a
junction temperature of 150°C for an extended period can
result in changes in the silicon devices potentially causing
failure.
The power dissipated in the package (PD) is the sum of the
quiescent power dissipation and the power dissipated in the
package due to the load drive for all outputs. The quiescent
power is the voltage between the supply pins (VS) times the
quiescent current (IS). The power dissipated due to the load
drive depends upon the particular application. For each output,
the power due to load drive is calculated by multiplying the load
current by the associated voltage drop across the device. The
power dissipated due to all of the loads is equal to the sum of
the power dissipation due to each individual load. RMS voltages
and currents must be used in these calculations.
Airflow increases heat dissipation, effectively reducing θJA. In
addition, more metal directly in contact with the package leads
from metal traces, through holes, ground, and power planes
reduces the θJA. The exposed paddle on the underside of the
package must be soldered to a pad on the PCB surface that is
thermally connected to a copper plane to achieve the specified θJA.
Figure 3 shows the maximum safe power dissipation in the
packages vs. the ambient temperature for the 8-lead SOIC
(79°C/W) and for the 8-lead LFCSP (81°C/W) on a JEDEC
standard 4-layer board, each with its underside paddle soldered
to a pad that is thermally connected to a PCB plane. θJA values
are approximations.
3.0
2.5
SOIC
2.0
LFCSP
1.5
1.0
0.5
0
–40
05681-041
Parameter
Supply Voltage
Power Dissipation
Storage Temperature Range
Operating Temperature Range
Lead Temperature Range (Soldering 10 sec)
Junction Temperature
MAXIMUM POWER DISSIPATION (W)
Table 3.
–20
0
20
40
60
80
AMBIENT TEMPERATURE (°C)
Figure 3. Maximum Power Dissipation vs. Temperature for a 4-Layer Board
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 5 of 20
ADA4922-1
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
8
IN
REF
2
7
DIS
VS+
3
6
VS–
OUT+
4
5
OUT–
NC = NO CONNECT
05681-001
ADA4922-1
NC
Figure 4. Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
Mnemonic
NC
REF
VS+
OUT+
OUT−
VS−
DIS
IN
Description
No Internal Connection
Reference Voltage for Single-Ended Input Signal
Positive Power Supply
Noninverting Side of Differential Output
Inverting Side of Differential Output
Negative Power Supply
Disable
Single-Ended Signal Input
Rev. 0 | Page 6 of 20
ADA4922-1
TYPICAL PERFORMANCE CHARACTERISTICS
Unless otherwise noted, VS = ±12 V, RL, dm = 1 kΩ, REF = 0 V, DIS = HIGH, TA = 25°C.
3
3
VS = ±5V
–6
–9
VS = ±12V
–15
–18
–21
–24
–27
–30
10
–6
–9
–12
–18
–21
–24
–27
–30
1
1000
100
VS = ±12V, VO, dm = 40V p-p
–15
FREQUENCY (MHz)
Figure 5. Small Signal Frequency Response for Various Power Supplies
3
–6
–9
–12
–15
–18
VS = ±12V @ +85°C
VS = ±5V @ +85°C
VS = ±12V @ +25°C
VS = ±5V @ +25°C
VS = ±12V @ –40°C
VS = ±5V @ –40°C
–27
–30
1
10
NORMALIZED CLOSED-LOOP GAIN (dB)
–3
05681-014
NORMALIZED CLOSED-LOOP GAIN (dB)
VO, dm = 0.2V p-p
0
–24
0
–3
–6
–9
VO, dm = 12V p-p (VS = ±5V)
VO, dm = 40V p-p (VS = ±12V)
–12
–15
–18
(ALL VOLTAGES ARE VO, dm)
40V p-p +85°C
40V p-p +25°C
40V p-p –40°C
12V p-p +85°C
12V p-p +25°C
12V p-p –40°C
–21
–24
–27
–30
1000
100
1
FREQUENCY (MHz)
–6
–9
–12
–15
–18
–21
VS = ±12V RL, dm = 1kΩ
VS = ±5V RL, dm = 1kΩ
VS = ±12V RL, dm = 500Ω
VS = ±5V RL, dm = 500Ω
–30
1
10
100
NORMALIZED CLOSED-LOOP GAIN (dB)
–3
05681-015
NORMALIZED CLOSED-LOOP GAIN (dB)
3
VO, dm = 0.2V p-p
–27
100
Figure 9. Large Signal Frequency Response at
Various Temperatures and Supplies
0
–24
10
FREQUENCY (MHz)
Figure 6. Small Signal Frequency Response for
Various Temperatures and Supplies
3
100
Figure 8. Large Signal Frequency Response for Various Power Supplies
3
–21
10
FREQUENCY (MHz)
05681-017
1
VS = ±5V, VO, dm = 12V p-p
0
–3
–6
–9
VO, dm = 12V p-p (VS = ±5V)
VO, dm = 40V p-p (VS = ±12V)
–12
–15
–18
–21
VS = ±12V, RL, dm = 1kΩ
VS = ±5V, RL, dm = 1kΩ
VS = ±12V, RL, dm = 500Ω
VS = ±5V, RL, dm = 500Ω
–24
–27
–30
1000
1
FREQUENCY (MHz)
10
FREQUENCY (MHz)
Figure 10. Large Signal Frequency Response for
Various Resistive Loads and Supplies
Figure 7. Small Signal Frequency Response for
Various Resistive Loads and Supplies
Rev. 0 | Page 7 of 20
05681-018
–12
0
–3
05681-016
NORMALIZED CLOSED-LOOP GAIN (dB)
–3
05681-013
NORMALIZED CLOSED-LOOP GAIN (dB)
VO, dm = 0.2V p-p
0
100
ADA4922-1
3
NORMALIZED CLOSED-LOOP GAIN (dB)
0
–3
–6
–9
–12
–15
–18
–21
VS = ±5V, CL, dm = 10pF
VS = ±5V, CL, dm = 20pF
VS = ±12V, CL, dm = 0pF
VS = ±12V, CL, dm = 20pF
–24
–27
–30
1
10
0
–3
–6
–9
–12
–15
–18
–21
–27
–30
1
1000
100
VS = ±5V, VIN = 12V p-p, CL, dm = 0pF
VS = ±12V, VIN = 40V p-p, CL, dm = 0pF
VS = ±5V, VIN = 12V p-p, CL, dm = 20pF
VS = ±12V, VIN = 40V p-p, CL, dm = 20pF
–24
FREQUENCY (MHz)
100
Figure 14. Large Signal Frequency Response for Various Capacitive Loads
3
3
0
0
–3
–3
0.2V p-p
–6
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
10
FREQUENCY (MHz)
Figure 11. Small Signal Frequency Response for Various Capacitive Loads
–9
–12
2V p-p
–15
16V p-p
–18
12V p-p
–21
–24
–6
0.2V p-p
–9
10V p-p
–12
–15
20V p-p
–18
–21
40V p-p
–24
2V p-p
10V p-p
–30
–33
1
10
100
05681-023
–27
05681-020
–27
–30
–33
1
1000
FREQUENCY (MHz)
10
Figure 15. Frequency Response for Various Output Amplitudes, VS = ±12 V
3
–60
–70
VS = ±12V
–80
VS ±5V
–100
05681-011
–110
–120
1
10
100
–3
VS = ±5V
–6
–9
–12
VS = ±12V
–15
–18
–21
–24
–27
–30
1
1000
10
100
1000
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 13. Isolation vs. Frequency—Disabled
VREF = 0.1V p-p
0
05681-024
VIN = 0.1V p-p
DIS = LOW
NORMALIZED CLOSED-LOOP GAIN (dB)
–50
–90
1000
100
FREQUENCY (MHz)
Figure 12. Frequency Response for Various Output Amplitudes, VS = ±5 V
ISOLATION (dB)
05681-050
VO, dm = 0.2V p-p
05681-019
NORMALIZED CLOSED-LOOP GAIN (dB)
3
Figure 16. REF Small Signal Frequency Response for Various Power Supplies
Rev. 0 | Page 8 of 20
ADA4922-1
–84
RL = 2kΩ
–87
–90
–93
–93
–96
DISTORTION (dBc)
–90
VS = ±5V, VO, dm = 12V p-p
–99
–102
–105
–108
1
10
–117
RL = 2kΩ
–120
100
1
10
FREQUENCY (kHz)
Figure 20. Harmonic Distortion for Various Loads
100
–60
RL = 2kΩ
SECOND HARMONIC
THIRD HARMONIC
–70
10
IMPEDANCE (Ω)
–80
VS = ±5V
–90
–100
–110
VON
VS = ±5V
VON
VS = ±12V
1
VOP
VS = ±5V
0.1
–120
05681-021
–130
VS = ±12V
–140
2
7
12
17
22
27
32
37
42
0.01
0.001
47
Figure 18. Harmonic Distortion vs. Output Amplitude and
Supply Voltage (f =10 kHz)
0
–20
–30
–40
+PSRR
–60
–PSRR
–70
05681-025
–80
–90
0.01
0.1
1
0.1
1
10
100
Figure 21. Single-Ended Output Impedance vs. Frequency and Supplies
–10
–100
0.001
0.01
FREQUENCY (MHz)
OUTPUT AMPLITUDE (V p-p)
–50
VOP
VS = ±12V
05681-030
DISTORTION (dBc)
100
FREQUENCY (kHz)
Figure 17. Harmonic Distortion for Various Power Supplies
PSRR (dB)
RL = 1kΩ
–108
–111
VS = ±12V, VO, dm = 40V p-p
RL = 600Ω
–105
–114
–117
SECOND HARMONIC
THIRD HARMONIC
–99
–102
–114
–120
VS = ±12V
VO, dm = 40V p-p
–96
–111
05681-012
DISTORTION (dBc)
SECOND HARMONIC
THIRD HARMONIC
05681-022
–84
–87
10
100
FREQUENCY (MHz)
Figure 19. PSRR vs. Frequency
Rev. 0 | Page 9 of 20
50
90
45
80
70
60
50
40
30
20
10
0
10
100
1k
10k
100k
1M
10M
35
30
25
20
15
10
5
0
100M
1
10
FREQUENCY (Hz)
0.10
100k
1M
Figure 25. Input Current Noise vs. Frequency
20ns/DIV
18
VS = ±12V
CL = 20pF
VOUT = 40V p-p
14
0.06
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
10k
22
VS = ±5V
0.08
1k
FREQUENCY (Hz)
Figure 22. Differential Output Noise vs. Frequency
0.12
100
0.04
0.02
0
–0.02
–0.04
–0.06
10
6
2
–2
–6
–10
–14
–0.08
100ns/DIV
05681-033
–0.10
–0.12
–18
–22
05681-027
1
40
05681-026
INPUT CURRENT NOISE (pA/√Hz)
100
05681-032
DIFFERENTIAL VOLTAGE NOISE (RTO) (nV/ Hz)
ADA4922-1
TIME (μs)
Figure 23. Small Signal Transient Response for Various Power Supplies
Figure 26. Large Signal Transient Response for Various Power Supplies
0.125
22
CL = 0pF
CL = 10pF
CL = 20pF
18
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
0.050
0.025
0
–0.025
–0.050
–0.075
10
CL = 20pF
6
2
–2
–6
–10
5ns/DIV
05681-037
–14
–0.100
–0.125
CL = 0pF
14
0.075
Figure 24. Small Signal Transient Response for Various Capacitive Loads
–18
20ns/DIV
–22
05681-040
0.100
Figure 27. Large Signal Transient Response for Various Capacitive Loads
Rev. 0 | Page 10 of 20
ADA4922-1
21
2.4
14
1.2
2
0
0
ERROR
–1.2
–2
12
8
VIN
4
7
0
0
ERROR
–4
–7
–2.4
–4
VOUT, dm
–8
–14
1μs/DIV
1μs/DIV
VS = ±5V
VO, dm = 12V p-p
–8
–3.6
–4.8
–21
05681-028
–6
ERROR (mV)
1 DIV = 0.01%
VIN
3.6
16
VS = ±12V
VO, dm = 40V p-p
–28
–12
–16
Figure 28. Settling Time, VS = ±5 V
05681-031
AMPLITUDE (V)
4
28
AMPLITUDE (V)
VOUT, dm
6
4.8
ERROR (mV)
1 DIV = 0.01%
8
Figure 31. Settling Time, VS = ±12 V
12
26
INPUT × 2
INPUT × 2
22
18
8
OUTPUT VOLTAGE (V)
0
–4
10
6
2
–2
–6
–10
OUTPUT
–14
OUTPUT
1μs/DIV
–12
–18
05681-029
–8
–22
1.2
50
45
0.8
40
0.6
35
FREQUENCY
VS = ±5V
0.2
VS = ±12V
–0.2
–0.4
30
VS = ±5V
MEAN = 0.25mV
STD. DEV. = 0.19mV
VS = ±12V
MEAN = –0.07mV
STD. DEV. = 0.17mV
NUMBER OF
UNITS = 590
25
20
15
–0.6
DIFFERENTIAL OUTPUT OFFSET VOLTAGE (mV)
Figure 30. Differential Output Offset Voltage vs. Temperature
Figure 33. Differential Output Offset Voltage Distribution
Rev. 0 | Page 11 of 20
1.000
0.875
0.750
0.625
0.500
0.375
0.250
TEMPERATURE (°C)
0
0
0.125
80
–0.125
60
–0.250
40
–0.375
20
–0.500
0
–0.750
–20
5
–0.875
–1.2
–40
–1.000
–1.0
05681-043
10
–0.8
05681-036
DIFFERENTIAL OUTPUT OFFSET VOLTAGE (mV)
Figure 32. Input Overdrive Recovery, VS = ±12 V
1.0
0
1μs/DIV
–26
Figure 29. Input Overdrive Recovery, VS = ±5 V
0.4
05681-035
4
–0.625
OUTPUT VOLTAGE (V)
14
12.0
10
11.5
9
POWER SUPPLY CURRENT (mA)
10.5
10.0
VS = ±12V
9.5
9.0
8.5
8.0
7.5
VS = ±5V
7.0
6.5
6.0
–40
–20
0
20
40
60
ISUPPLY = ±12V
8
7
ISUPPLY = ±5V
6
5
4
3
2
05681-044
11.0
05681-038
POWER SUPPLY CURRENT (mA)
ADA4922-1
1
0
80
0
0.5
TEMPERATURE (°C)
1.0
1.5
2.0
2.5
3.0
3.5
4.0
DIS INPUT VOLTAGE WITH RESPECT TO VS– (V)
Figure 37. Power Supply Current vs. Disable Input Voltage
Figure 34. Power Supply Current vs. Temperature
5
3.0
4
INPUT BIAS CURRENT (μA)
2.0
1.0
–40
INPUT BIAS CURRENT, VS = ±5V
REFERENCE BIAS CURRENT, VS = ±5V
INPUT BIAS CURRENT, VS = ±12V
REFERENCE BIAS CURRENT, VS = ±12V
–20
0
20
40
1
0
–1
IB = ±5V
–2
–3
05681-039
1.5
IB = ±12V
2
60
05681-045
INPUT BIAS CURRENT (μA)
3
2.5
–4
–5
80
0
TEMPERATURE (°C)
2
4
6
8
10
12
14
16
18
20
22
24
INPUT VOLTAGE WITH RESPECT TO VS– (V)
Figure 35. Input Bias Current vs. Temperature
Figure 38. Input Bias Current vs. Input Voltage
VO, dm = 2V p-p
VO, dm = 2V p-p
DIS INPUT
VDIS = –8.5V
VDIS = –8.5V
500mV/DIV
500mV/DIV
VO, dm
40μs/DIV
40μs/DIV
Figure 36. Disable Turn-On Time
Figure 39. Disable Turn-Off Time
Rev. 0 | Page 12 of 20
05681-048
VDIS = –10.5V
VO, dm
05681-046
VDIS = –10.5V
DIS INPUT
ADA4922-1
300
200
150
PART ON
PART OFF
100
IDIS = ±5V
50
0
IDIS = ±12V
–50
05681-047
DIS INPUT CURRENT (μA)
250
–100
–150
0
5
10
15
20
DIS VOLTAGE WITH RESPECT TO VS– (V)
Figure 40. Disable Current vs. Disable Voltage
Rev. 0 | Page 13 of 20
ADA4922-1
THEORY OF OPERATION
The ADA4922-1 is dual amplifier that has been optimized to
drive a differential ADC from a single-ended input source with
a minimum number of external components (see Figure 41).
IN
OUT+
R
OUT–
REF
05681-002
R
If an application uses an input midswing voltage other than
midsupply, the REF pin needs to be offset to the input midswing
level to obtain outputs that do not exhibit a differential offset
(see Figure 43). If the voltage applied to the REF pin is different
from the midswing level of the input signal, a dc offset is
created between outputs VOUT+ and VOUT−. Figure 44 illustrates
this condition when the input signal is referenced to a positive
level, and the REF pin is connected to 0 V.
10
Figure 41. Functional Diagram
VIN
5
The differential output voltage is defined as
0
Each amplifier in Figure 41 is identical, and the value of Resistor R
is set at 600 Ω, yielding an optimal trade-off between output
differential noise, internal power dissipation, and overall
system linearity. For basic operation, the REF input is tied to
the midswing level of the input signal, which is often midsupply.
The input signal (referenced to REF) produces a differential
output signal with an overall gain of +2. Figure 42 shows typical
operation on ±12 V supplies with the source referenced to 0 V
and the REF pin tied to 0 V.
REF
–5
–10
10
5
OUT+
0
OUT–
05681-004
(1)
VOLTAGE (V)
VO, dm = VOUT+ − VOUT−
–2.5
0
5
10
15
20
25
30
35
40
45
50
TIME (μs)
Figure 43. Typical Input/Output Response—Equal Input/Reference
20
20
VIN
10
15
10
0
REF
VOLTAGE (V)
10
OUT+
0
REF
–5
10
5
OUT+
0
OUT–
–10
0
5
10
15
20
25
30
35
40
45
–5
OUT–
–10
50
0
TIME (μs)
Figure 42. Typical Input/Output Response—Centered Reference
05681-005
0
–5
05681-003
VOLTAGE (V)
–20
5
VIN
5
–10
5
10
15
20
25
30
35
40
45
50
TIME (μs)
Figure 44. Typical Input/Output Response—Unequal Input/Reference
Rev. 0 | Page 14 of 20
ADA4922-1
A more detailed view of the amplifier is shown in Figure 45.
Each amplifier is a 2-stage design that uses an input H-Bridge
followed by a rail-to-rail output stage (see Figure 46).
The architecture used in the ADA4922-1 results in excellent
SNR and distortion performance when compared to other
differential amplifiers.
MIRROR
I
C
I
RIN
INP
OUTPUT
STAGE
INN
I
05681-006
I
OUT
MIRROR
One of the more subtle points of operation arises when the two
amplifiers are used to generate the differential outputs. Because
the differential outputs are derived from a follower amplifier
and an inverting amplifier, they have different noise gains and,
therefore, different closed-loop bandwidths. For frequencies up
to 1 MHz, the bandwidth difference between outputs causes
little difference in the overall differential output performance.
However, because the bandwidth is the sum of both amplifiers,
the 3 dB point of the inverting amplifier defines the overall
differential 3 dB corner (see Figure 48).
0
Figure 45. Internal Amplifier Architecture
OUT+
–2
I
CLOSED-LOOP GAIN
MIRROR
I
ROUT
IN
INTERNAL
REF
OUT–
–6
7
DIFFERENTIAL OUTPUT
5
I
MIRROR
1
10k
Figure 46. Output Stage Architecture
05681-010
3
05681-007
I
OUT
–4
100k
1M
10M
100M
FREQUENCY (Hz)
Figure 47 illustrates the open-loop gain and phase relationships
of each amplifier in the ADA4922-1.
125
GAIN
75
50
25
0
–25
–50
–75
PHASE
05681-008
MAGNITUDE/PHASE (dB/Degrees)
100
–100
–125
100
1k
10k
100k
1M
10M
Figure 48. Closed-Loop AC Gain (Differential Outputs)
Small delay and gain errors exist between the two outputs
because the inverting output is derived from the noninverting
output through an inverting amplifier. The gain error is due to
imperfect matching of the inverting amplifier gain and feedback
resistors, as well as differences in the transfer functions of the
two amplifiers, as illustrated in Figure 48. The delay error is due
to the delay through the inverting amplifier relative to the
noninverting amplifier output. The delay produces a reduction
in differential gain because the two outputs are not exactly 180°
out of phase. Both of these errors combine to produce an overall
gain error because the outputs are completely balanced. This
error is very small at the frequencies involved in most
ADA4922-1 applications.
100M
FREQUENCY (Hz)
Figure 47. Amplifier Gain/Phase Relationship
Rev. 0 | Page 15 of 20
ADA4922-1
APPLICATIONS
The ADA4922-1 is a fixed-gain, single-ended-to-differential
voltage amplifier, optimized for driving high resolution ADCs
in high voltage applications. There are no gain adjustments
available to the user.
Voltage Noise @ OUT− due to VnRf: VnRF
ADA4922-1 DIFFERENTIAL OUTPUT NOISE MODEL
When looking at OUT− by itself, the contributing noise sources
are uncorrelated, and therefore, the total output noise is
calculated as the root-sum-square (rss) of the individual
contributors. When looking at the differential output noise, the
noise contributors are uncorrelated except for three, Vn1, RS(In1),
and VnRs, which are common noise sources for both outputs. It
can be seen from the previous results that the output noise due
to Vn1, RS(In1), and VnRs each appear at OUT+ with a gain of +1
and at OUT− with a gain of −1. This produces a gain of 2 for each
of these three sources at the differential output.
⎛ Rf
Voltage Noise @ OUT− due toVn2: Vn2 ⎜1 +
⎜ Rg
⎝
The principal noise sources in a typical ADA4922-1 application
circuit are shown in Figure 49.
VnRf
Vn1
VnRg
Rf
Rg
Rs
Vn2
OUT–
In1
REF
OUT+
05681-042
VnRs
(8)
⎞
⎟ = 2V
n2
⎟
⎠
(9)
The total differential output noise density is calculated as
Figure 49. ADA4922-1 Differential Output Noise Model
Using the traditional approach, a noise source is applied in
series with one of the inputs of each op amp to model inputreferred voltage noise. The input current noise that matters the
most is present at the input pin. The output voltage noise due to
this noise current depends on the source resistance feeding the
input, as well as the downstream gain in the amplifier. Resistor
noise is modeled by placing a noise voltage source in series with
a noiseless resistor. Rf and Rg are both 600 Ω and therefore have
the same noise voltage density.
Von, dm =
(2(V
n
+ Rs (1.4 pA/ Hz ) + VnRs
)) + 2(3.2 nV/
2
)
2
Hz + 4Vn2 (10)
where Vn1 = Vn2 ≡ Vn = 3.9 nV/√Hz; the input referred voltage
noise of each amplifier is the same.
The output noise due to the amplifier alone is calculated by
setting RS and VnRs equal to zero. In this case:
Von, dm = 12 nV/√Hz
(11)
At room temperature,
VnRg = VnRf = 4 kT(600 Ω ) ≈ 3.2 nV/ Hz
(2)
The noise at OUT+ is due to the input-referred current and
voltage noise sources of the noninverting amplifier and the
noise of the source resistance, all reflected to the output with a
noise gain of 1, and is equal to:
Voltage Noise @ OUT+: Vn1 + RS(In1) + VnRs
(3)
where RS is the source resistance feeding the input, and VnRs is
the source resistance noise.
The noise at OUT− originates from a number of sources:
⎛ − Rf
Voltage Noise @ OUT− due to Vn1: Vn1 ⎜
⎜ Rg
⎝
⎞
⎟ = − Vn1
⎟
⎠
⎛ − Rf
Voltage Noise @ OUT− due to In1: RS (I n1 )⎜
⎜ Rg
⎝
(4)
⎞
⎟ = − R (I n1 ) (5)
S
⎟
⎠
⎛ − Rf
Voltage Noise @ OUT− due to RS: VnRs ⎜
⎜ Rg
⎝
⎞
⎟ = − VnRs
⎟
⎠
(6)
⎛ − Rf
Voltage Noise @ OUT− due to VnRg: VnRg ⎜
⎜ Rg
⎝
⎞
⎟ = − VnRg
⎟
⎠
(7)
Clearly, the output noise is not balanced between the outputs,
but this is not an issue in most applications.
USING THE REF PIN
The REF pin sets the output baseline in the inverting path and
is used as a reference for the input signal. In most applications,
the REF pin is set to the input signal midswing level, which in
many cases is also midsupply. For bipolar signals and power
supplies, REF is generally set to ground. In single-supply
applications, setting REF to the input signal midswing level
provides optimal output dynamic range performance with
minimum differential offset. Note that the REF input only
affects the inverting signal path, or OUT−.
Most applications require a differential output signal with the
same dc common-mode level on each output. It is possible for
the signal measured across OUT+ and OUT− to have a commonmode voltage that is of the desired level but has different dc
levels at both outputs. Typically, this situation is avoided,
because it wastes the amplifier’s output dynamic range.
Rev. 0 | Page 16 of 20
ADA4922-1
DISABLE FEATURE
VOUT+ = +VIN
(12)
VOUT− = −VIN + 2(REF)
(13)
When the REF voltage is set to the midswing level of the input
signal, the two output signals fall directly on top of each other
with minimal offset. Setting the REF voltage elsewhere results
in an offset between the two outputs. This effect is illustrated in
the Theory of Operation section.
The best use of the REF pin can be further illustrated by
considering a single-supply example that uses a 10 V dc power
supply and has an input signal that varies between 2 V and 7 V.
This is a case where the midswing level of the input signal is not
at midsupply but is at 4.5 V. By setting the REF input to 4.5 V
and neglecting offsets, Equation 12 and Equation 13 are used to
calculate the results. When the input signal is at its midpoint of
4.5 V, VOUT+ is at 4.5 V, as is VOUT−. This can be considered as a
type of baseline state where the differential output voltage is
zero. When the input increases to 7 V, VOUT+ tracks the input to
7 V and VOUT− decreases to 2 V. This can be viewed as a positive
peak signal where the differential output voltage equals 5 V.
When the input signal decreases to 2 V, VOUT+ again tracks to
2 V, and VOUT− increases to 7 V. This can be viewed as a negative
peak signal where the differential output voltage equals −5 V.
The resulting differential output voltage is 10 V p-p.
The previous discussion exposes how the single-ended-todifferential gain of 2 is achieved.
INTERNAL FEEDBACK NETWORK POWER
DISSIPATION
While traditional op amps do not have on-chip feedback
elements, the ADA4922-1 contains two on-chip 600 Ω resistors
that comprise an internal feedback loop. The power dissipated
in these resistors must be included in the overall power dissipation
calculations for the device. Under certain circumstances, the
power dissipated in these resistors could be considerably more
than the device’s quiescent current. For example, on ±12 V
supplies with the REF pin tied to ground and OUT− at 9 V dc,
each 600 Ω resistor carries 15 mA and dissipates 135 mW. This
is a significant amount of power and must therefore be included
in the overall device power dissipation calculations. For ac
signals, rms analysis is required.
The ADA4922-1 includes a disable feature that can be asserted
to minimize power consumption in a device that is not needed
at a particular time. When asserted, the disable feature does not
place the device output in a high impedance or three-state
condition. The disable feature is asserted by applying a control
voltage to the DIS pin and is active low. See the Specifications
section for the high and low level voltage specifications.
DRIVING A DIFFERENTIAL INPUT ADC
The ADA4922-1 provides the single-ended-to-differential
conversion that is required to drive most high resolution ADCs.
Figure 50 shows how the ADA4922-1 simplifies ADC driving.
+12V
+12V
0.1μF
7
3
DIS
VS+
0.1μF
ADA4922-1
8 IN
OUT+ 4
VIN
±10V
R
C
R
R
C
HIGH VOLTAGE
HIGH RESOLUTION
ADC
OUT– 5
2 REF
R
VS–
0.1μF
6
–12V
05681-049
Defining VIN as the voltage applied to the input pin, the
equations that govern the two signal paths are given in
Equation 12 and Equation 13.
0.1μF
–12V
Figure 50. Driving a Differential Input ADC
For example, consider the case where the input signal
bandwidth is 100 KHz and R = 41.2 Ω and C = 3.9 nF, as is
shown in Figure 50, to form a single-pole filter with −3 dB
bandwidth of approximately 1 MHz. The ADA4922-1 output
noise (with zero source resistance) integrated over this
bandwidth appears at the ADC input and is calculated as
(
Vn, ADC , dm (rms) = 12 nV/ Hz
)
⎛ π ⎞(1MHz ) = 15μV rms
⎜ ⎟
⎝2⎠
(14)
The rms value of a 20 V p-p signal at the ADC input is 7 V rms,
yielding a SNR of 113 dB at the ADC input.
Rev. 0 | Page 17 of 20
ADA4922-1
PRINTED CIRCUIT BOARD LAYOUT
CONSIDERATIONS
Although the ADA4922-1 is used in many applications
involving frequencies that are well below 1 MHz, some general
high speed layout practices must be adhered to because it is a
high speed amplifier. Controlled impedance transmission lines
are not required for low frequency signals, provided the signal
rise times are longer than approximately 5 times the electrical
delay of the interconnections. For reference, typical 50 Ω
transmission lines on FR-4 material exhibit approximately
140 ps/in delay on outer layers and 180 ps/in for inner layers.
Most connections between the ADA4922-1 and the
ADC can be kept very short.
Broadband power supply decoupling networks should be placed
as close as possible to the supply pins. Small surface-mount
ceramic capacitors are recommended for these networks, and
tantalum capacitors are recommended for bulk supply
decoupling.
Rev. 0 | Page 18 of 20
ADA4922-1
OUTLINE DIMENSIONS
5.00 (0.197)
4.90 (0.193)
4.80 (0.189)
4.00 (0.157)
3.90 (0.154)
3.80 (0.150)
8
5
TOP VIEW
1
4
2.29 (0.092)
2.29 (0.092)
6.20 (0.244)
6.00 (0.236)
5.80 (0.228)
BOTTOM VIEW
1.27 (0.05)
BSC
(PINS UP)
0.50 (0.020)
× 45
0.25 (0.010)
1.75 (0.069)
1.35 (0.053)
0.25 (0.0098)
0.10 (0.0039)
COPLANARITY
SEATING
0.10
PLANE
8°
0.25 (0.0098) 0° 1.27 (0.050)
0.40 (0.016)
0.17 (0.0068)
0.51 (0.020)
0.31 (0.012)
COMPLIANT TO JEDEC STANDARDS MS-012-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETER; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 51. 8-Lead Standard Small Outline Package with Exposed Pad [SOIC_N_EP]
Narrow Body (RD-8-1)
Dimensions shown in millimeters and (inches
3.00
BSC SQ
0.60 MAX
0.50
0.40
0.30
1
8
PIN 1
INDICATOR
0.90 MAX
0.85 NOM
TOP
VIEW
2.75
BSC SQ
0.50
BSC
1.50
REF
5
4
1.60
1.45
1.30
0.70 MAX
0.65 TYP
12° MAX
0.05 MAX
0.01 NOM
SEATING
PLANE
0.30
0.23
0.18
0.20 REF
Figure 52. 8-Lead Lead Frame Chip Scale Package [LFCSP_VD]
3 mm × 3 mm Body, Very Thin, Dual Lead (CP-8-2)
Dimensions shown in millimeters
Rev. 0 | Page 19 of 20
PIN 1
INDICATOR
1.89
1.74
1.59
ADA4922-1
ORDERING GUIDE
Model
ADA4922-1ARDZ 1
ADA4922-1ARDZ-RL1
ADA4922-1ARDZ-R71
ADA4922-1ACPZ-R21
ADA4922-1ACPZ-RL1
ADA4922-1ACPZ-RL71
1
Temperature Range
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
Package Description
8-Lead Small Outline Package (SOIC_N_EP)
8-Lead Small Outline Package (SOIC_N_EP)
8-Lead Small Outline Package (SOIC_N_EP)
8-Lead Lead Frame Chip Scale Package (LFCSP_VD)
8-Lead Lead Frame Chip Scale Package (LFCSP_VD)
8-Lead Lead Frame Chip Scale Package (LFCSP_VD)
Z = Pb-free part.
© 2005 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05681–0–10/05(0)
Rev. 0 | Page 20 of 20
Package Option
RD-8-1
RD-8-1
RD-8-1
CP-8-2
CP-8-2
CP-8-2
Branding
HUB
HUB
HUB