16-Bit, 80 MSPS A/D Converter AD10678 FUNCTIONAL BLOCK DIAGRAM 80 MSPS sample rate 80 dBFS signal-to-noise ratio Transformer-coupled analog input Single PECL clock source Digital outputs True binary format 3.3 V and 5 V CMOS compatible AIN AD10678 AIN 14 ADC DOUT0 14 ADC 14 ADC DIGITAL POSTPROCESSING DOUT15 APPLICATIONS Low signature radar Medical imaging Communications instrumentation Instrumentation Antenna array processing OUTPUT DATA BITS 14 ADC ANALOG POWER AGND 5VA 3.3VE AGND DRY CLOCK DISTRIBUTION CIRCUIT DGND 3.3V DGND ENCODE ENCODE DIGITAL POWER 03376-A-001 FEATURES Figure 1. GENERAL DESCRIPTION PRODUCT HIGHLIGHTS The AD10678 is a 16-bit, high performance, analog-to-digital converter for applications that demand increased SNR levels. Exceptional noise performance and a typical signal-to-noise ratio of 80 dBFS are obtained by digitally postprocessing the outputs of four ADCs. Only a single analog input and PECL sampling clock, as well as 3.3 V and 5 V power supplies, are required. 1. 2. 3. Guaranteed sample rate of 80 MSPS. Input signal conditioning with optimized noise performance. Fully tested and guaranteed performance. The AD10678 is assembled using a 0.062" thick laminate board with three sets of connector interface pads to accommodate analog and digital isolation. Analog Devices recommends using this connector from Samtec: FSI-110-03-G-D-AD-K-TR. The overall card fits a 2.2" × 2.8" PCB specified from 0°C to 70°C. Rev. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.326.8703 © 2003 Analog Devices, Inc. All rights reserved. AD10678 TABLE OF CONTENTS Features .......................................................................................... 1 Explanation of Test Levels............................................................5 Applications................................................................................... 1 Absolute Maximum Ratings ............................................................6 Functional block diagram ........................................................... 1 Operating Range............................................................................6 General Description..................................................................... 1 ESD Caution...................................................................................6 Product Highlights ....................................................................... 1 Test Circuits........................................................................................7 Revision History ........................................................................... 2 AD10678–Typical Performance Characteristics ........................ 10 AD10678–Specifications ................................................................. 3 Definition of Specifications ...................................................... 12 DC Specifications ......................................................................... 3 Thermal Considerations............................................................ 12 Digital Specifications ................................................................... 3 Theory of Operation.................................................................. 13 AC Specifications.......................................................................... 4 Outline Dimensions ....................................................................... 20 Switching Specifications .............................................................. 5 Ordering Guide .......................................................................... 20 REVISION HISTORY 12/03—Data sheet changed from REV. 0 to REV.A Updated format....................................................................Universal Changes to AC Specifications table footnotes ............................... 4 Changes to Table 1............................................................................. 3 Changes to Table 3............................................................................. 6 Changes to Figure 11....................................................................... 10 Changes to Theory of Operation................................................... 13 Changes to Ordering Guide ........................................................... 20 Rev. A | Page 2 of 20 AD10678 AD10678–SPECIFICATIONS DC SPECIFICATIONS Table 1. AVCC = 5 V, EVCC = 3.3 V, VDD = 3.3 V; TA = 25°C, Differential Encode = 80 MSPS, CLOAD ≤ 10 pF, unless otherwise noted. Parameter RESOLUTION Offset Error Gain Error Differential Nonlinearity (DNL) Integral Nonlinearity (INL) TEMPERATURE DRIFT Offset Error Gain Error POWER SUPPLY REJECTION RATIO (PSRR) ANALOG INPUTS (AIN, AIN)1 Differential Input Voltage Range Differential Input Resistance Differential Input Capacitance Input Bandwidth VSWR 2 POWER SUPPLY 3 Supply Current IAVCC (AVCC = 5.0 V) IEVCC (EVCC = 3.3 V) IVDD (VDD = 3.3 V) Total Power Dissipation 4 Test Level Min I I V V –0.30 –7 Typ 16 +0.12 ±0.7 ±4 Unit Bits %FS %FS LSB LSB V V V 13 200 60 ppm/°C ppm/°C dB V V V IV V 2.15 50 2.5 V p-p Ω nF MHz Ratio 0.40 Max +0.30 +7 220 1.04:1 I I I I 0.95 0.15 0.49 6.86 1.1 0.2 0.625 8.0 A A A W 1 Measurement includes the recommended interface connector. Input VSWR, see Figure 15. 3 Supply voltages should remain stable within ±5% for normal operation. 4 Power dissipation measures with encode at rated speed and –1 dBFS analog input at 10 MHz. 2 DIGITAL SPECIFICATIONS Table 2. AVCC = 5 V, EVCC = 3.3 V, VDD = 3.3 V; TA = 25°C, Differential Encode = 80 MSPS, CLOAD ≤ 10 pF, unless otherwise noted. Parameter ENCODE INPUTS (ENCODE, ENCODE) Differential Input Voltage Range Differential Input Resistance Differential Input Capacitance LOGIC OUTPUTS (D15 to D0) Logic Compatibility Logic 1 Voltage—ILOAD ≤100 mA Logic 0 Voltage—ILOAD ≤100 mA Output Coding Series Output Resistance—per Bit Test Level Min IV V V 0.4 IV IV Rev. A | Page 3 of 20 Typ 100 160 CMOS 0.9 × VDD 0.4 True Binary 120 Max Unit V p-p Ω pF V V Ω AD10678 AC SPECIFICATIONS Table 3. AVCC = 5 V, EVCC = 3.3 V, VDD = 3.3 V; TA = 25°C, Differential Encode = 80 MSPS, CLOAD ≤ 10 pF, unless otherwise noted. Parameter SNR 1 Analog Input @ –6 dBFS SINAD 2 Analog Input @ –6 dBFS SFDR 3 Analog Input @ –6 dBFS Test Level Min Typ 2.5 MHz 10 MHz 30 MHz 70 MHz I I I I 77.5 77.5 77 76 80.5 80.5 80.2 78 dBFS dBFS dBFS dBFS 2.5 MHz 10 MHz 30 MHz 70 MHz I I I I 77.2 77.2 76.6 74.7 80.3 80.3 79.7 77.4 dBFS dBFS dBFS dBFS 2.5 MHz 10 MHz 30 MHz 70 MHz I I I I 88 88 84 81 97.2 97.2 94.2 91.7 dBFS dBFS dBFS dBFS 96 84 dBFS dBFS TWO-TONE 4 Analog Input @ –7 dBFS—IMD f1 = 10 MHz, f2 = 12 MHz f1 = 70 MHz, f2 = 72 MHz V V 1 Max Unit Analog input signal power at –6 dBFS; signal-to-noise (SNR) is the ratio of signal level to total noise (first five harmonics removed). Encode = 80 MSPS. SNR is reported in dBFS, related back to converter full scale. 2 Analog input signal power at –6 dBFS; signal-to-noise and distortion (SINAD) is the ratio of signal level to total noise + harmonics. Encode = 80 MSPS. SINAD is reported in dBFS, related back to converter full scale. 3 Analog input signal equals –6 dBFS; SFDR is the ratio of converter full scale to worst spur. 4 Both input tones at–7 dBFS; two tone intermodulation distortion (IMD) rejection is the ratio of either tone to the worst third-order intermodulation product. Rev. A | Page 4 of 20 AD10678 SWITCHING SPECIFICATIONS Table 4. AVCC = 5 V, EVCC = 3.3 V, VDD = 3.3 V; TA = 25°C, Differential Encode = 80 MSPS, CLOAD ≤ 10 pF, unless otherwise noted. Parameter MAXIMUM CONVERSION RATE MINIMUM CONVERSION RATE DUTY CYCLE ENCODE INPUTS PARAMETERS Encode Period @ 80 MSPS, tENC Encode Pulse Width High @ 80 MSPS, tENCH Encode Pulse Width Low @ 80 MSPS, tENCL ENCODE/DATA (D15:D0) Propagation Delay, tPDH Valid Time, tPDL ENCODE/DATA READY1 Encode Rising to Data Ready Falling, tDR_F Encode Rising to Data Ready Rising, tDR_R DATA READY/DATA1 Data Ready to Data (Hold Time)—tH_DR Data Ready to Data (Setup Time)—tS_DR APERTURE DELAY, tA APERTURE UNCERTAINTY (JITTER), tJ PIPELINE DELAYS 1 Test Level I IV IV Min 80 Typ 30 60 40 V V V V V V Max Unit MSPS MSPS % 12.5 6.25 6.25 ns ns ns 6.7 7.3 ns ns 12.6 6.4 ns ns 10 1 480 500 10 ns ns ps fs rms Cycles Duty Cycle = 50%. EXPLANATION OF TEST LEVELS I. II. III. IV. V. VI. 100% production tested. 100% production tested at 25°C and sample tested at specified temperatures. Sample tested only. Parameter is guaranteed by design and characterization testing. Parameter is a typical value only. 100% production tested at 25°C; guaranteed by design and characterization testing for industrial temperature range; 100% production tested at temperature extremes for military devices. Rev. A | Page 5 of 20 AD10678 ABSOLUTE MAXIMUM RATINGS Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 5. AD10678 Stress Ratings Parameter AVCC to AGND EVCC to AGND VDD to DGND Analog Input Voltage Analog Input Current Encode Input Voltage Digital Output Voltage Maximum Junction Temperature Storage Temperature Range Ambient Maximum Operating Temperature Ambient Rating 0 V to 7 V 0 V to 6 V –0.5 V to +3.8 V 0 V to AVCC 25 mA 0 V to 5 V –0.5 V to VDD 150°C –65°C to +150°C 92°C OPERATING RANGE Operating Ambient Temperature Range: 0°C to 70°C. See Thermal Considerations section. Table 6. Output Coding (True Binary) Code 65535 . . . 32768 32767 . . . 0 AIN (V) +1.1 . . . 0 –0.000034 . . . –1.1 Digital Output 1111 1111 1111 1111 . . . 1000 0000 0000 0000 0111 1111 1111 1111 . . . 0000 0000 0000 0000 ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. A | Page 6 of 20 AD10678 TEST CIRCUITS tA N N+2 N+1 N+3 N+4 N+5 N+6 N+3 N+4 N+5 N+6 N–7 N–6 N–5 ANALOG INPUT tENCL N ENCODE, ENCODE N+1 tENCH N+2 tPDH N–10 DATA BITS, D[15:0] tPDL N–9 N–8 tS_DR DATA-READY OUTPUT N N+1 tH_DR N+2 tDR_R N+3 tDR_F N+4 N+5 03376-A-002 tENC N+6 Figure 2. Timing Diagram VCH AVCC BUF 1:1 AIN 25Ω 200Ω VCL VREF BUF 500Ω VCH AIN T/H 500Ω 25Ω AVCC 500Ω BUF T/H 03376-A-003 ×4 VCL Figure 3. Analog Input Stage VDD P 37.5kΩ MACROCELL LOGIC 100Ω ENC PECL DRIVER 03376-A-004 ENC 120Ω N Figure 5. Digital Output Stage Figure 4. Equivalent Encode Input VDD VDD P MACROCELL LOGIC N Figure 6. Data-Ready Output Rev. A | Page 7 of 20 03376-A-023 DRY 1kΩ D0–D15 03376-A-005 VDD EVCC AD10678 Table 7. Interfaces 1 and 2: Digital Pin Function Descriptions P1: Pin Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Mnemonic DGND DGND DOUT15 NC DOUT14 DGND DOUT13 NC DOUT12 DGND DOUT11 NC DOUT10 DGND DOUT9 NC DOUT8 DGND DGND DRY P2: Pin Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Function Digital Ground Digital Ground Data Bit Output No Connection Data Bit Output Digital Ground Data Bit Output No Connection Data Bit Output Digital Ground Data Bit Output No Connection Data Bit Output Digital Ground Data Bit Output No Connection Data Bit Output Digital Ground Digital Ground Data Ready Output Table 8 Interface 3: Analog Pin Function Descriptions P3: Pin Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Mnemonic +3.3VE +5.0VA +3.3VE +5.0VA AGND +5.0VA AGND +5.0VA AGND AGND AGND AIN AGND AIN ENCODE AGND ENCODE AGND AGND AGND Function Encode Voltage (EVCC) Analog Voltage (AVCC) Encode Voltage (EVCC) Analog Voltage (AVCC) Analog Ground Analog Voltage (AVCC) Analog Ground Analog Voltage (AVCC) Analog Ground Analog Ground Analog Ground Analog Input Analog Ground Analog Input Encode Input Analog Ground Encode Input Analog Ground Analog Ground Analog Ground Rev. A | Page 8 of 20 Mnemonic DGND DGND +3.3VD DOUT0 +3.3VD DOUT1 +3.3VD DOUT2 DGND DOUT3 DGND DOUT4 DGND DOUT5 DGND DOUT6 +3.3VD DOUT7 +3.3VD DGND Function Digital Ground Digital Ground Digital Voltage (VDD) Data Bit Output Digital Voltage (VDD) Data Bit Output Digital Voltage (VDD) Data Bit Output Digital Ground Data Bit Output Digital Ground Data Bit Output Digital Ground Data Bit Output Digital Ground Data Bit Output Digital Voltage (VDD) Data Bit Output Digital Voltage (VDD) Digital Ground AD10678 Top View of Interface PCB Assembly Dimensions shown in inches Tolerances: 0.xx = ±10 mils 0.xxx = ±5 mils 0.466 20 2 P2 MH4 19 1 0.960 0.888 2.148 P3 19 20 1.223 MH2 1.693 1 0.433 2 0.925 0.805 0.900 MH1 20 2 0.526 P1 MH3 19 1 0.757 INTERFACE NOTES: SUGGESTED INTERFACE MANUFACTURER: SAMTEC INTERFACE PART NUMBERS FOR P1-P3: FSI-110-03-G-D-AD-K-TR (20-PIN) HOLES 1–4 ACCOMMODATE 2-56 THREADED HARDWARE. USE FOUR 2-56 NUTS FOR SECURING THE PART TO INTERFACE PCB. MANUFACTURER: BUILDING FASTENERS PART NUMBER: HNSS256 DIGIKEY #: H723-ND Figure 7. Header Interface Dimensions (Inches) Rev. A | Page 9 of 20 03376-A-006 0.955 AD10678 AD10678–TYPICAL PERFORMANCE CHARACTERISTICS 0 0 ENCODE = 80MSPS AIN = 2.5MHz SNR = 80.79dBFS SFDR = 97.22dBFS –10 –20 –30 –30 –40 –40 –50 –50 –60 –60 dBFS –70 –70 –80 –90 –100 –100 –110 –110 –120 –120 –130 0 5 10 15 20 25 FREQUENCY (MHz) 30 35 40 03376-A-007 –90 –130 0 5 Figure. 8. Single-Tone at 2.5 MHz 30 35 40 0 ENCODE = 80MSPS AIN = 10MHz SNR = 80.76dBFS SFDR = 94.81dBFS –10 –20 ENCODE = 80MSPS AIN = 10.1MHz AND 12.1MHz IMD = 98.25dBFS –10 –20 –30 –30 –40 –40 –50 –50 –60 –60 dBFS –70 –80 –70 –80 –90 –100 –100 –110 –110 –120 –120 –130 0 5 10 15 20 25 FREQUENCY (MHz) 30 35 40 03376-A-008 –90 –130 0 Figure 9. Single-Tone at 10 MHz 5 10 15 20 25 FREQUENCY (MHz) 30 35 40 03376-A-011 dBFS 15 20 25 FREQUENCY (MHz) Figure 11. Single-Tone at 70 MHz 0 Figure 12. Two-Tone at 10.1 MHz and 12.1 MHz 0 0 ENCODE = 80MSPS –10 AIN = 32MHz –20 SNR = 80.18dBFS SFDR = 91.8dBFS –30 ENCODE = 80MSPS AIN = 70MHz AND 72MHz IMD = 87.5dBFS –10 –20 –30 –40 –50 –50 –60 –60 dBFS –40 –70 –80 –70 –80 –90 –90 –100 –100 –110 –110 –120 –120 –130 0 5 10 15 20 25 FREQUENCY (MHz) 30 35 40 03376-A-009 dBFS 10 03376-A-010 –80 Figure 10. Single-Tone at 32 MHz –130 0 5 10 15 20 25 FREQUENCY (MHz) 30 35 Figure 13. Two-Tone at 70 MHz and 72 MHz Rev. A | Page 10 of 20 40 03376-A-012 dBFS –20 ENCODE = 80MSPS AIN = 70MHz SNR = 78.31dBFS SFDR = 87.64dBFS –10 AD10678 0 100 –0.30 SNR 2.5MHz SNR 10MHz 90 AIN = –1dB –0.60 80 –0.90 70 –1.20 60 SFDR 2.5MHz SFDR 30MHz –1.80 40 –2.10 30 –2.40 20 –2.70 10 –3.00 1.0 15.9 30.8 45.7 60.6 75.5 90.4 105.3 120.2 135.1 150.0 FREQUENCY (MHz) SNR 70MHz 50 SNR 30MHz SFDR 10MHz 0 –80 Figure 14. Gain Flatness –70 –60 –50 –40 –30 –20 FUNDAMENTAL LEVEL (dBFS) –10 0 03376-A-015 dBc –1.50 03376-A-013 dBFS SFDR 70MHz Figure 16. SFDR and SNR vs. Analog Input Level 2.0 100 1.9 1.8 94 SFDR 1.7 dBc 1.5 88 1.4 1.3 82 1.2 SNR 1.1 1.0 0.1 1 10 FREQUENCY (MHz) 100 1k Figure 15. Analog Input VSWR 76 0 10 20 30 40 50 60 ANALOG INPUT FREQUENCY (MHz) 70 Figure 17. SFDR and SNR vs. Analog Input Frequency Rev. A | Page 11 of 20 03376-A-024 VSWR 03376-A-014 VSWR 1.6 AD10678 DEFINITION OF SPECIFICATIONS Analog Bandwidth The analog input frequency at which the spectral power of the fundamental frequency (as determined by the FFT analysis) is reduced by 3 dB. Aperture Delay The delay between the 50% point on the rising edge of the ENCODE command and the instant at which the analog input is sampled. Aperture Uncertainty (Jitter) The sample-to-sample variation in aperture delay. Differential Nonlinearity The deviation of any code from an ideal 1 LSB step. Signal-to-Noise Ratio (SNR) The ratio of the rms signal amplitude (set at 1 dB below full scale) to the rms value of the sum of all other spectral components, excluding the first five harmonics and dc. May be reported in dBc (i.e., degrades as signal level is lowered) or in dBFS (always related back to converter full scale). Spurious-Free Dynamic Range (SFDR) The ratio of the rms signal amplitude to the rms value of the peak spurious spectral component. The peak spurious component may or may not be a harmonic. May be reported in dBc (i.e., degrades as signal level is lowered) or in dBFS (always related back to converter full scale). Two-Tone Intermodulation Distortion Rejection (IMD) Ratio of the rms value of either input tone to the rms value of the worst third-order intermodulation product; reported in dBc. Encode Pulse Width/Duty Cycle Pulse width high is the minimum amount of time that the ENCODE pulse should be left in Logic 1 state to achieve rated performance; pulse width low is the minimum time that the ENCODE pulse should be left in low state. At a given clock rate, these specifications define an acceptable encode duty cycle. Harmonic Distortion The ratio of the rms signal amplitude to the rms value of the worst harmonic component. Minimum Conversion Rate The encode rate at which the SNR of the lowest analog signal frequency drops by no more than 3 dB below the guaranteed limit. Voltage Standing-Wave Ratio (VSWR) The ratio of the amplitude of the elective field at a voltage maximum to that at an adjacent voltage minimum. THERMAL CONSIDERATIONS Due to the high power nature of the part, it is critical that the following thermal conditions be met for the part to perform to data sheet specifications. This also ensures that the maximum junction temperature (150°C) is not exceeded. • Operation temperature (tA) must be within 0°C to 70°C. • All mounting standoffs should be fastened to the interface PCB assembly with 2-56 nuts. This ensures good thermal paths as well as excellent ground points. • The unit rises to ~72°C (tC) on the heat sink in still air (0 linear feet per minute (LFM)). The minimum recommended air flow is 100 linear feet per minute (LFM) in either direction across the heat sink (see Figure 18). Maximum Conversion Rate The encode rate at which parametric testing is performed. Output Propagation Delay The delay between the 50% point of the rising edge of the ENCODE command and the time when all output data bits are within valid logic levels. Signal-to-Noise-and-Distortion (SINAD) The ratio of the rms signal amplitude (set at 1 dB below full scale) to the rms value of the sum of all other spectral components, including the first five harmonics and dc. May be reported in dBc (i.e., degrades as signal level is lowered) or in dBFS (always related back to converter full scale). 70 65 TEMPERATURE (CASE) (°C) Power Supply Rejection Ratio The ratio of a change in output offset voltage to a change in power supply voltage. 75 60 55 50 45 40 35 30 0 50 100 150 200 AIR FLOW (LFM) 250 Figure 18. Temperature (Case) vs. Air Flow (Ambient) Rev. A | Page 12 of 20 300 03376-A-025 Integral Nonlinearity The deviation of the transfer function from a reference line measured in fractions of 1 LSB using a “best straight line” determined by a least square curve fit. AD10678 THEORY OF OPERATION The AD10678 employs four parallel, high speed analog-to-digital converters in a correlation technique to improve the dynamic range of the ADCs. The technique consists of summing the parallel outputs of the four converters to reduce the uncorrelated noise introduced by the individual converters. Signals processed through the high speed adder are correlated and summed coherently. Noise is not correlated and sums on an rms basis. Analog and Digital Power Supplies The four high speed, analog-to-digital converters employ a threestage subrange architecture. The AD10678 provides The +3.3VE supply provides power to the clock distribution circuit. The +3.3VD supply provides power to the digital output section of the ADCs, the PECL-to-TTL translator, and the CPLD. Separate +3.3VE and +3.3VD supplies are used to prevent modulation of the clock signal with digital noise. The +5VA supply provides power to the analog sections of the ADCs. Decoupling capacitors are strategically placed throughout the circuit to provide low impedance noise shunts to ground. The +5VA supply (analog power) should be decoupled to AGND (analog ground) and +3.3VD (digital power) should be decoupled to DGND (digital ground). The +3.3VE supply (analog power) should be decoupled to AGND. The evaluation board schematic and layout data provide a typical PCB implementation of the AD10678. complementary analog input pins, AIN and AIN . Each analog input is centered around 2.4 V and should swing ±0.55 V around the reference. Since AIN and AIN are 180 degrees out of phase, the differential analog input signal is 2.15 V p-p. The analog input is designed for a 50 Ω input impedance for easy interface to commercially available cables, filters, and drivers, etc. The AD10678 encode inputs are ac-coupled to a PECL differential receiver/driver. The output of the receiver/driver provides a clock source for a 1:5 PECL clock driver and a PECL-to-TTL translator. The 1:5 PECL clock driver provides the differential encode signal for each of the four high speed analog-to-digital converters. The PECL-to-TTL translator is used to provide a clock source for the complex programmable logic device (CPLD). The digital outputs from the four ADCs drive 120 Ω series output terminators and are applied to the CPLD for postprocessing. The digital outputs are added together in the complex programmable logic device through a ripple-carry adder, which provides the 16-bit data output. The AD10678 provides valid data following 10 pipeline delays. The result is a 16-bit parallel digital CMOS compatible word coded as true binary. Input Stage The user is provided with a single-to-differential transformer coupled input. The input impedance is 50 Ω and requires a 2.15 V p-p input level to achieve full scale. Encoding the AD10678 The AD10678 encode signal must be a high quality, low phase noise source to prevent performance degradation. The clock input must be treated as an analog input signal because aperture jitter may affect dynamic performance. For optimum performance, the AD10678 must be clocked differentially. Care must be taken when selecting a power source. Linear supplies are recommended. Switching supplies tend to have radiated components that may be coupled into the ADCs. The AD10678 features separate analog and digital supply and ground currents, helping to minimize digital corruption of sensitive analog signals. Analog and Digital Grounding Although the AD10678 provides separate analog and digital ground pins, the device should be treated as an analog component. Proper grounding is essential in high speed, high resolution systems. Multilayer printed circuit boards are recommended to provide optimal grounding and power distribution. The use of power and ground planes provides distinct advantages. Power and ground planes minimize the loop area encompassed by a signal and its return path, minimize the impedance associated with power and ground paths, and provide a distributed capacitor formed by the power plane, printed circuit board material, and ground plane. The AD10678 unit is provided with four metal standoffs (see Figure 7). MH2 is located in the center of the unit and MH1 is located directly below analog header P3. Both of these standoffs are tied to analog ground and should be connected accordingly on the next level assembly for optimum performance. The two standoffs located near P1 and P2 (MH3 and MH4) are tied to digital ground and should be connected accordingly on the next-level assembly. Output Loading Take care when designing the data receivers for the AD10678. The complex programmable logic device 16-bit outputs drive 120 Ω series resistors to limit the amount of current that can flow into the output stage. To minimize capacitive loading, there should only be one gate on each of the output pins. A typical CMOS gate combined with the PCB trace has a load of approximately 10 pF. It should be noted that extra capacitive loading increases output timing and invalidates timing specifications. Digital output timing is guaranteed with a 10 pF load. Rev. A | Page 13 of 20 AD10678 Other Notes The circuit is configured on a 2.2" × 2.8" laminate board with three sets of connector interface pads. The pads are configured in such a way that easy “keying” is provided to the user. The pads are made for low profile applications and have a total height of 0.12" after mating. The part numbers for the header mates are provided in Figure 7. All pins of the analog and digital sections are described in Table 7 and Table 8. Evaluation Board The AD10678 evaluation board provides an easy way to test the 16-bit 80 MSPS A/D converter. The board requires a clock source, an analog input signal, two 3.3 V power supplies, and a 5 V power supply. The clock source is buffered on the board to provide the clock for the AD10678, a latch, and a data ready signal. To use the AD10678 data ready output to clock the buffer memory, remove R24 (0.0 Ω) and install a 0.0 Ω resistor at R31 (DNI). The ADC digital outputs are latched on board by a 74LCX16374. The digital outputs and output clock are available on a 40-pin connector J1. Power is supplied to the board via uninsulated metal banana jacks. The analog input is connected via an SMA connector AIN. The analog input section provides for a single-ended input option or a differential input option. The board is shipped in a single-ended analog input option. Removing a ground tie at E17 converts the circuit to a differential analog input configuration. Table 9. PCB Bill of Material Item 1 2 3 4 5 6 7 8 9 10 11 12 Quantity 1 1 3 3 6 2 1 1 19 1 4 17 13 14 15 16 6 4 1 1 Reference Designator J1 U1 L1 to L3 J11 to J13 P1, P2, P8 to P10, P12 U5, U6 U7 R24 R0 to R16, R20, R23 R17 R18, R19, R21, R22 C1, C10 to C13, C16 to C18, C23 to C26, C29 to C32 C8, C9, C4, C15, C27, C33 J2, J3, J5, J6 A1 AD106xx Evaluation Board Description Connector, 40-Position Header, Male Straight IC, LV 16-Bit D-Type Flip-Flop with 5 V Tolerant I/O Common-Mode Surface-Mount Ferrite Bead 20 Ω Connector, 1 mm Single Element Interface Uninsulated BANANA JACK All Metal IC, 3.3 V/5 V ECL Differential Receiver/Driver IC, 3.3 V Dual Differential LVPECL to LVTTL Translator RES 0.0 Ω 1/10 W 5% 0805 SMD RES 51.1 Ω 1/10 W 1% 0805 SMD RES 18.2 kΩ 1/10 W 1% 0805 SMD RES 100 Ω 1/10 W 1% 0805 SMD CAP 0.1 µF 16 V CERAMIC X7R 0805 CAP 10 µF 10 V CERAMIC Y5V 1206 CONNECTOR, SMA JACK 200 Mil STR GOLD ASSEMBLY, AD10678BWS GS04483 (PCB) Rev. A | Page 14 of 20 Figure 19. Evaluation Board Schematic C13 0.1µF 16V C10 0.1µF 16V 03376-A-016 AGND +5VA AGND 8 7 6 5 +3.3VE R18 100Ω R19 100Ω R21 R22 100Ω 100Ω AGND AGND 2 4 C8 10µF 10V 1 3 P2 P9 AGND AGND +5VA C9 10µF 10V +3.3VE P1 L2 C12 0.1µF 16V R30 DNI C11 0.1µF 16V AGND C15 10µF 10V C25 0.1µF 16V C26 0.1µF 10V AGND AGND AGND MC10EL16D 8 7 6 5 AGND AGND MC10EL16D AGND NC VCC D Q D Q VBB VEE +3.3VE R17 U6 18.2kΩ 1 NC VCC 2 D Q 3 D Q 4 VBB VEE 1 2 3 4 U5 POWER CONNECTIONS L1 P10 1 2 +3.3VE 3 4 R20 51.1Ω J5 ENCODE R16 51.1Ω J6 ENCODE C32 0.1µF 16V +3.3VE 1 J13 2 3 4 5 6 7 8 10 9 12 11 14 13 16 15 18 17 20 19 2 4 6 8 10 12 14 16 18 20 AGND C14 10µF 10V VCC 8 Q0 7 Q1 6 5 E17 R27 DNI AGND R28 DNI R29 DNI R24 0.0Ω R23 51.1Ω R31 DNI C18 0.1µF 16V C29 0.1µF 16V DGND DRY AGND E2 AGND E6 AGND E10 AGND E12 AGND E18 AGND E19 DGND DGND MH3 OPTIONAL EVALUATION BOARD GROUND TIES C16 0.1µF 16V +3.3VD C17 LATCH 0.1µF 16V BUFMEM DGND BYPASS CAPACITORS +3.3VD MH2 AGND AGND J3 J2 ANALOG INPUT E15 DGND AGND AGND DGND SINGLE-ENDED DIFFERENTIAL INPUT OPTION INPUT OPTION DGND MC100ELT23D DGND D1 GND 1 D0 2 D0 3 D1 4 +3.3VD U7 AGND MH1 AGND FSI-110-03-G-D-AD-TR 1 3 5 7 9 11 13 15 17 19 C30 0.1µF 16V DGND J12 +5VA MH4 AGND E21 E4 C28 0.1µF 16V DGND E3 AGND AGND C23 0.1µF 16V +3.3VE DGND HEADER 732mm MH1–4 = DUT MOUNTING HOLES DRY 2 4 6 8 10 12 14 1 3 5 7 9 11 13 Rev. A | Page 15 of 20 J8 19 17 15 13 11 9 7 5 3 1 19 17 15 13 11 9 7 5 3 1 20 18 16 14 12 10 8 6 4 2 DGND E20 20 18 16 14 12 10 8 6 4 2 AD10678 PART OUTLINE SI-110-03-G-D-AD-TR J11 20 20 19 19 18 18 17 17 16 16 15 15 14 13 14 13 12 12 11 11 10 10 9 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 FSI-110-03-G-D-AD-TR DGND VCC VCC CP2 VCC OE2 VCC I15 O15 O14 I14 I13 O13 I12 O12 I11 O11 O10 I10 I9 O9 I8 O8 CP1 OE1 I7 O7 I6 O6 I5 O5 I4 O4 I3 O3 I2 O2 I1 O1 I0 O0 GND GND GND GND GND GND GND GND U1 DGND E22 DGND E13 DGND P12 P8 DGND AGND +3.3VD 12 11 9 8 6 5 3 2 21 15 10 4 42 31 7 18 23 22 20 19 17 16 14 13 DGND E1 E5 L3 2 4 E11 DGND C27 10µF 10V +3.3VD 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1 40-PIN HMS 40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 J1 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1 C24 0.1µF 16V DGND E8 C1 0.1µF 16V DGND DGND E9 E7 R8 51.1Ω R9 51.1Ω R10 51.1Ω R11 51.1Ω R12 51.1Ω R13 51.1Ω R14 51.1Ω R15 51.1Ω +3.3VD DGND DGND 1 3 R25 DNI R0 51.1Ω R1 51.1Ω R2 51.1Ω R3 51.1Ω R4 51.1Ω R5 51.1Ω R6 51.1Ω R7 51.1Ω +3.3VD BUFMEM 74LCX16374MTD 25 24 26 27 29 30 32 33 35 36 48 1 37 38 40 41 43 44 46 47 28 34 39 45 C31 0.1µF 16V POWER CONNECTIONS R30 DNI DGND LATCH DGND C33 10µF 10V +3.3VD DGND 40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 AD10678 AD10678 03376-A-017 AD10678/PCP EVALUATION BOARD Figure 20. Evaluation Board Mechanical Layout Top View Rev. A | Page 16 of 20 03376-A-018 AD10678 Figure 21. Evaluation Board Mechanical Layout Bottom View Rev. A | Page 17 of 20 03376-A-019 AD10678 03376-A-020 Figure 22. Evaluation Board Top Layer Copper Figure 23. Evaluation Board Second Layer Copper Rev. A | Page 18 of 20 03376-A-021 AD10678 03376-A-022 Figure 24. Evaluation Board Third Layer Copper Figure 25. Evaluation Board Bottom Layer Copper Rev. A | Page 19 of 20 AD10678 OUTLINE DIMENSIONS Dimensions shown in inches Tolerances: 0.xx = ±10 mils 0.xxx = ±5 mils 2.795 2.745 2.695 0.170 0.120 0.070 a 2.220 2.170 2.120 AD10678BWS LOT NUMBER DATA CODE USA 0.370 0.320 0.270 0.314 0.264 0.214 Top View Figure 26. ORDERING GUIDE Model AD10678BWS AD10678/PCB Temperature Range 0°C to 70°C 25°C Package Description Non-Herm Hybrid Surf Mount (2.2" × 2.8") Evaluation Board © 2003 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. C03376-0-12/03(A) Rev. A | Page 20 of 20 Package Option WS-120