Rev.3.0 BATTERY PROTECTION IC (FOR A 2-SERIAL-CELL PACK) S-8232 SERIES The 8232 is a series of lithium-ion rechargeable battery protection ICs incorporating high-accuracy voltage detection circuits and delay circuits. It is suitable for a 2-serial-cell lithium-ion battery pack. Features (1) Internal high-accuracy voltage detection circuit y Overcharge detection voltage 3.90 V ± 25 mV to 4.60 V ± 25 mV 5 mV- step 3.60 V ± 50 mV to 4.60 V ± 50 mV y Overcharge release voltage 5 mV- step (The Overcharge release voltage can be selected within the range where a difference from Overcharge detection voltage is 0 to 0.3 V) y Overdischarge detection voltage 1.70 V ± 80 mV to 2.60 V ± 80 mV 50 mV- step 1.70 V ± 100 mV to 3.80 V ± 100 mV y Overdischarge release voltage 50 mV - step (The Overdischarge release voltage can be selected within the range where a difference from Overdischarge detection voltage is 0 to 1.2V) y Overcurrent detection voltage 1 0.07 V ± 20 mV to 0.30 V ± 20 mV 5 mV-step (2) High input-voltage device (absolute maximum rating: 18 V) (3) Wide operating voltage range: (4) The delay time for every detection can be set via an external capacitor. 2.0 V to 16 V Each delay time for Overcharge detection, Overdischarge detection, Overcurrent detection are “Proportion of hundred to ten to one.” (5) Two overcurrent detection levels (protection for short-circuiting) (6) Internal auxiliary over voltage detection circuit (Fail safe for over voltage) (7) Internal charge circuit for 0V battery (Unavailable is option) (8) Low current consumption (9) y Operation 7.5 µA typ. 14.2 µA max (-40 to +85 °C) y Power-down mode 0.2 nA typ. 0.1 µA max (-40 to +85 °C) TSSOP package (8-pin) 6.4 mm×3.1 mm Applications Lithium-ion rechargeable battery packs Seiko Instruments Inc. 1 Battery Protection IC (for a 2-serial-cell pack) S-8232 Series Rev.3.0 Selection Guide(12 Jan , 1998) Table1 *1: *2: *3: *4: Model/Item Overcharge detection voltage1,2 (VCU1,2) Overcharge release voltage1,2 (VCD1,2) S-8232AAFT 4.25V±25mV 4.05±50mV Overdischarge Overdischarge detection release voltage1,2 voltage1,2 (VDD1,2) (VDU1,2) 2.40V±80mV Overcurrent detection voltage1 (VIOV1) 3.00V±100mV 0.150V±20mV Overcharge detection delay time (tCU) C3=0.22µF 0V battery charging function 1.0 sec Available S-8232ABFT 4.35V±25mV 4.15±50mV 2.30V±80mV 3.00V±100mV 0.300V±20mV 1.0 sec Available S-8232ACFT 4.35V±25mV 4.15±50mV 2.30V±80mV 3.00V±100mV 0.300V±20mV 1.0 sec Unavailable S-8232AEFT 4.35V±25mV 4.28±50mV 2.15V±80mV 2.80V±100mV 0.100V±20mV 1.0 sec Available S-8232AFFT 4.25V±25mV 4.05±50mV 2.30V±80mV 2.70V±100mV 0.300V±20mV 1.0 sec Available S-8232AGFT 4.25V±25mV 4.05±50mV 2.20V±80mV 2.40V±100mV 0.200V±20mV 1.0 sec Available S-8232AHFT 4.25V±25mV 4.05±50mV 2.20V±80mV 2.40V±100mV 0.300V±20mV 1.0 sec Available S-8232AIFT 4.325V±25mV 4.325V *1,2 2.40V±80mV 3.00V±100mV 0.300V±20mV 1.0 sec Unavailable S-8232AJFT 4.25V±25mV 4.05±50mV 2.40V±80mV 3.00V±100mV 0.150V±20mV 1.0 sec Unavailable S-8232AKFT 4.20V±25mV 4.00±50mV 2.30V±80mV 2.90V±100mV 0.200V±20mV 1.0 sec Available S-8232ALFT 4.30V±25mV 4.05±50mV 2.00V±80mV 3.00V±100mV 0.200V±20mV 1.0 sec Available S-8232AMFT 4.19V±25mV 4.19 V *1 2.00V±80mV 3.00V±100mV 0.190V±20mV 1.0 sec Available S-8232ANFT 4.325V±25mV 4.325V *1,3 2.40V±80mV 3.00V±100mV 0.300V±20mV 1.0 sec Unavailable S-8232AOFT 4.30V±25mV 4.05±50mV 2.00V±80mV 3.00V±100mV 0.230V±20mV 1.0 sec Available S-8232APFT 4.28V±25mV 4.05±50mV 2.30V±80mV 2.90V±100mV 0.100V±20mV 1.0 sec Unavailable S-8232ARFT 4.325V±25mV 4. .325V *1,3 2.00V±80mV 2.50V±100mV 0.300V±20mV 1.0 sec Unavailable S-8232ASFT *4 4.295V±25mV 4.20±50mV *3 2.30V±80mV 3.00V±100mV 0.300V±20mV 1.0 sec Unavailable S-8232ATFT 4.125V±25mV 4.125±50mV *1 2.00V±80mV 3.00V±100mV 0.190V±20mV 1.0 sec Available S-8232AUFT 4.30V±25mV 4.10±50mV 2.40V±80mV 3.00V±100mV 0.200V±20mV 1.0 sec Unavailable S-8232AVFT 4.30V±25mV 4.05V±50mV 2.00V±80mV 3.00V±100mV 0.300V±20mV 1.0 sec Available S-8232AWFT 4.35V±25mV 4.15V±50mV 2.30V±80mV 3.00V±100mV 0.150V±20mV 1.0 sec Unavailable No overcharge detection/release hysteresis The magnification of final overcharge is 1.11; other is 1.25. No final overcharging function Refer to the Description of Operation (*3). Change in the detection voltage is available in products other than the above listed ones. Please contact with our sales division. The overdischarge detection voltage can be selected within the range from 1.7 to 3.0V. When the Overdischarge detection voltage is higher than 2.6V, the Overcharge detection voltage and the Overcharge release voltage are limited as table 2. Table 2 2 Overdischarge detection voltage1,2 (VDD1,2) Overcharge detection voltage1,2 (VCU1,2) Voltage difference between Overcharge detection voltage and Overcharge release voltage (VCU1,2 - VCD1,2) 1.70 to 2.60 V 3.90 to 4.60 V 0 to 0.30 V 1.70 to 2.80 V 3.90 to 4.60 V 0 to 0.20 V 1.70 to 3.00 V 3.90 to 4.50 V 0 to 0.10 V Seiko Instruments Inc. Battery Protection IC (for a 2-serial-cell pack) S-8232 Series Rev.3.0 Block Diagram VCC SENS Reference voltage 1 - Auxiliary Over charge + Over charge detector 1 + DO - Control + Logic Delay circuit control signal Over discharge detector 1 VC CO Over discharge detector 2 RCOL + Over charge detector 2 Over current detection circuit + + - VSS VM Delay circuit control signal Delay circuit control signal Auxiliary Over charge Reference detector 2 voltage 2 Delay circuit control signal Delay circuit ICT DO,CO control signal Figure 1 Output impedance when CO terminal output ‘L’ is higher than DO terminal. RCOL resistor is connected with CO terminal. Please refer ‘Electric Characteristics’. Seiko Instruments Inc. 3 Battery Protection IC (for a 2-serial-cell pack) S-8232 Series Rev.3.0 Pin Assignment Pin Description Table 3 Top View SENS 1 8 VCC DO 2 7 VC CO 3 6 ICT VM 4 5 VSS TSSOP-8 No. Name 1 SENS 2 DO Connects FET gate for discharge control (CMOS output) 3 CO Connects FET gate for charge control (CMOS output) 4 VM Detects pin for VM voltage (Overcurrent detection pin) 5 VSS Negative power input pin (Connects battery2 negative voltage) 6 ICT Connects capacitor for delay circuit 7 VC Detects pin for VCC voltage (Connects battery1 positive voltage) The middle pin between two batteries (Connects battery1 negative voltage and battery2 positive voltage) Figure 2 8 Description VCC Positive power input pin (Connects battery1 positive voltage) Absolute Maximum Ratings Table 4 4 Ta = 25°C Item Symbol Applied Pins Rating Unit Input voltage between VCC and VSS VDS VCC VSS-0.3 to VCC+18 V SENS Input terminal voltage VSENS SENS VSS-0.3 to VCC+0.3 V ICT Input terminal voltage VICT ICT VSS-0.3 to VCC+0.3 V VM Input terminal voltage VVM VM VCC-18 to VCC+0.3 V DO output terminal voltage VDO DO VSS-0.3 to VCC+0.3 V CO output terminal voltage VCO CO VVM-0.3 to VCC+0.3 V Power dissipation PD 300 mW Operating temperature range Topr -40 to +85 °C Storage temperature range Tstg -40 to +125 °C Seiko Instruments Inc. Battery Protection IC (for a 2-serial-cell pack) S-8232 Series Rev.3.0 Electrical Characteristics Table 5 Ta = 25°C Symbol Condition Circuit Notice Min. Typ. Max. Unit VCU1,2 1,2 1 3.90 to 4.60 Adjustment VCU1,2 VCU1,2 VCU1,2 V Detection voltage Overcharge detection voltage 1,2 -0.025 Auxiliary overcharge detection voltage VCUaux1,2 1,2 1 VCU1,2×1.25 Fixed Type 1,2 +0.025 VCU1,2 VCU1,2 VCU1,2 ×1.21 ×1.25 ×1.29 VCU1,2 VCU1,2 VCU1,2 ×1.07 ×1.11 ×1.15 VCD1,2 VCD1,2 VCD1,2 V VCUaux1,2 = VCU1,2×1.25 or VCUaux1,2 = VCU1,2×1.11 VCUaux1,2 Overcharge release voltage 1,2 VCD1,2 1,2 1,2 1 1 VCU1,2×1.11 Fixed Type 3.60 to 4.60 Adjustment -0.050 Overdischarge detection voltage 1,2 VDD1,2 1,2 1 1.70 to 2.60 Adjustment VDD1,2 VDU1,2 1,2 1 1.70 to 3.80 Adjustment VDU1,2 V +0.050 VDD1,2 -0.080 Overdischarge release voltage 1,2 V VDD1,2 V +0.080 VDU1,2 -0.100 VDU1,2 V +0.100 Overcurrent detection voltage 1 VIOV1 3 1 0.07 to 0.30 Adjustment VIOV1-0.020 VIOV1 VIOV1+0.020 V Overcurrent detection voltage 2 VIOV2 3 1 VCC Reference -1.57 -1.20 -0.83 V Voltage temperature factor 1 TCOE1 (*1) Ta=-40 to 85°C -0.6 0 0.6 mV/°C Voltage temperature factor 2 TCOE2 (*2) Ta=-40 to 85°C -0.24 -0.05 0 mV/°C 0.73 1.00 1.35 68 100 138 6.7 10 13.9 -0.3 --- 18 (*3) 2.0 --- 16 V Delay time(C3=0.22µF) Overcharge detection tCU1,2 8,9 5 1.0 S S delay time1,2 Overdischarge detection tDD1,2 8,9 5 0.1 S mS delay time 1,2 Overcurrent detection delay time1 tIOV1 10 5 0.01 S mS Input voltage Input voltage between absolute maximum rating VCC and VSS Operating voltage Operating voltage between VCC and VSS VDSOP Current consumption Current consumption IOPE 4 2 V1=V2=3.6V 2.1 7.5 12.7 µA IPDN 4 2 V1=V2=1.5V 0 0.0002 0.04 µA V during normal operation Current consumption at power down Output voltage DO”H”voltage VDO(H) 6 3 at Iout=10uA VCC-0.05 VCC-0.003 --- DO”L”voltage VDO(L) 6 3 at Iout=10uA --- VSS+0.003 VSS+0.05 V CO”H”voltage VCO(H) 7 4 at Iout=10uA VCC-0.15 VCC-0.019 --- V RCOL 7 4 VSS-CO=4.7V×2 0.29 0.6 1.44 MΩ Rvcm 5 2 Vcc-VM=0.5V 105 240 575 511 597 977 CO pin internal resistance Resistance between VSS and CO Internal resistance Resistance between VCC and VM Resistance between Rvsm 5 2 KΩ VM-VSS=1.1V VSS and VM KΩ 0V battery charging function 0V charge starting voltage V0CHA 11 6 0V batt. Cha. Available 0.38 0.75 1.12 V 0V charge inhibiting voltage 1,2 V0INH1,2 12,13 6 0V batt. Cha. Unavailable 0.32 0.88 1.44 V (*1)Voltage temperature factor 1 indicates overcharge detection voltage, overcharge release voltage, overdischarge detection voltage, and overdischarge release voltage. (*2)Voltage temperature factor 2 indicates overcurrent detection voltage. (*3)The DO and CO logic must be established for the operating voltage. Seiko Instruments Inc. 5 Battery Protection IC (for a 2-serial-cell pack) S-8232 Series Table 6 Rev.3.0 Ta = -40 to +85°C Symbol Condition Circuit Notice Min. Typ. Max. Unit VCU1,2 1,2 1 3.90 to 4.60 VCU1,2 VCU1,2 VCU1,2 V Adjustment -0.055 VCU1,2×1.25 Fixed. VCU1,2 VCU1,2 VCU1,2 Type ×1.19 ×1.25 ×1.31 VCU1,2×1.11 Fixed. VCU1,2 VCU1,2 VCU1,2 Type ×1.05 ×1.11 ×1.17 3.60 to 4.60 VCD1,2 VCD1,2 VCD1,2 Adjustment -0.080 1.70 to 2.60 VDD1,2 Adjustment -0.110 1.70 to 3.80 VDU1,2 Adjustment -0.130 0.07 to 0.30 VIOV1-0.033 Detection voltage Overcharge detection voltage 1,2 Auxiliary overcharge detection voltage 1,2 VCUaux1,2 1,2 1 VCUaux1,2 = VCU1,2×1.25 +0.045 V or VCUaux1,2 = VCU1,2×1.11 VCUaux1,2 Overcharge release voltage 1,2 Overdischarge detection voltage 1,2 Overdischarge release voltage 1,2 Overcurrent detection voltage 1 1,2 VCD1,2 1,2 VDD1,2 1,2 VDU1,2 1,2 VIOV1 3 1 1 1 1 1 1 V +0.070 VDD1,2 VDD1,2 V +0.100 VDU1,2 VDU1,2 V +0.120 VIOV1 Adjustment 3 V VIOV1+0.0 V 33 Overcurrent detection voltage 2 VIOV2 VCC Reference -1.70 -1.20 -0.71 V Voltage temperature factor 1 TCOE1 (*1) Ta=-40 to 85°C -0.6 0 0.6 mV/°C Voltage temperature factor 2 TCOE2 (*2) Ta=-40 to 85°C -0.24 -0.05 0 mV/°C 0.55 1.00 2.06 67 100 141 6.3 10 14.7 -0.3 --- 18 (*3) 2.0 --- 16 V Delay time(C3=0.22µF) Overcharge detection tCU1,2 8,9 5 1.0 S delay time1,2 Overdischarge detection tDD1,2 8,9 5 0.1 S delay time 1,2 Overcurrent detection delay time1 tIOV1 10 5 S mS 0.01 S mS Input voltage Input voltage between absolute maximum VCC and VSS rating Operating voltage Operating voltage between VCC and VSS VDSOP Current consumption Current consumption IOPE 4 2 V1=V2=3.6V 1.8 7.5 14.2 µA IPDN 4 2 V1=V2=1.5V 0 0.0002 0.10 µA V during normal operation Current consumption at power down Output voltage DO”H”voltage VDO(H) 6 3 at Iout=10uA VCC-0.17 VCC-0.003 --- DO”L”voltage VDO(L) 6 3 at Iout=10uA --- VSS+0.003 VSS+0.17 V CO”H”voltage VCO(H) 7 4 at Iout=10uA VCC-0.27 VCC-0.019 --- V RCOL 7 4 VSS-CO=4.7V×2 0.22 0.6 2.20 MΩ Rvcm 5 2 Vcc-VM=0.5V 79 240 878 387 597 1491 CO pin internal resistance Resistance between VSS and CO Internal resistance Resistance between VCC and VM Resistance between Rvsm 5 2 KΩ VM-VSS=1.1V VSS and VM KΩ 0V battery charging function 0V charge starting voltage V0CHA 11 6 0V batt. Cha. Available 0.26 0.75 1.25 V 0V charge inhibiting voltage 1,2 V0INH1,2 12,13 6 0V batt. Cha. 0.20 0.88 1.57 V Unavailable (*1)Voltage temperature factor 1 indicates overcharge detection voltage, overcharge release voltage, overdischarge detection voltage, and overdischarge release voltage. (*2)Voltage temperature factor 2 indicates overcurrent detection voltage. (*3)The DO and CO logic must be established for the operating voltage. 6 Seiko Instruments Inc. Battery Protection IC (for a 2-serial-cell pack) S-8232 Series Rev.3.0 Measurement Circuits (1) Measurement 1 Measurement circuit 1 Set S1=OFF, V1=V2=3.6 V, and V3=0V under normal condition. Increase V1 from 3.6 V gradually. The V1 voltage when CO = 'L' is overcharge detection voltage 1 (VCU1). Decrease V1 gradually. The V1 voltage when CO = 'H' is overcharge release voltage 1 (VCD1). Further decrease V1. The V1 voltage when DO = 'L' is overdischarge voltage 1 (VDD1). Increase V1 gradually. The V1 voltage when DO = 'H' is overdischarge release voltage 1 (VDU1). Set S1=ON,and V1=V2=3.6 V and V3=0V under normal condition. Increase V1 from 3.6 V gradually. The V1 voltage when CO = 'L' is auxiliary overcharge detection voltage 1 (VCUaux1). (2) Measurement 2 Measurement circuit 1 Set S1=OFF,V1=V2=3.6 V ,and V3=0V under normal condition. Increase V2 from 3.6 V gradually. The V2 voltage when CO = 'L' is overcharge detection voltage 2 (VCU2). Decrease V2 gradually. The V2 voltage when CO = 'H' is overcharge release voltage 2 (VCD2). Further decrease V2. The V2 voltage when DO = 'L' is overdischarge voltage 2 (VDD2). Increase V2 gradually. The V2 voltage when DO = 'H' is overdischarge release voltage 2 (VDU2). Set S1=ON,and V1=V2=3.6 V and V3=0V under normal condition. Increase V2 from 3.6 V gradually. The V2 voltage when CO = 'L' is auxiliary overcharge detection voltage 2 (VCUaux2). (3) Measurement 3 Measurement circuit 1 Set S1=OFF,V1=V2=3.6 V , and V3=0V under normal condition. Increase V3 from 0V gradually. The V3 voltage when DO = 'L' is overcurrent detection voltage 1 (VIOV1). Set S1=ON,V1=V2=3.6 V,V3=0 under normal condition. Increase V3 from 0V gradually.(The voltage change rate < 1.0V/msec) (V1+V2-V3) voltage when DO = 'L' is overcurrent detection voltage 2 (VIOV2). (4) Measurement 4 Measurement circuit 2 Set S1=ON, V1=V2=3.6 V, and V3=0 V under normal condition and measure current consumption. Current consumption I1 is the normal condition current consumption (IOPE). Set S1=OFF, V1=V2=1.5 V under overdischarge condition and measure current consumption. Current consumption I1 is the power-down current consumption (IPDN). (5) Measurement 5 Measurement circuit 2 Set S1=ON, V1=V2=V3=1.5 V, and V3=2.5V under overdischarge condition. (V1+V2-V3)/I2 is the internal resistance between VCC and VM (Rvcm). Set S1=ON, V1=V2=3.5V, and V3=1.1 V under overcurrent condition. V3/I2 is the internal resistance between VSS and VM (Rvsm). Seiko Instruments Inc. 7 Battery Protection IC (for a 2-serial-cell pack) S-8232 Series Rev.3.0 (6) Measurement 6 Measurement circuit 3 Set S1=ON, S2=OFF, V1=V2=3.6 V, and V3=0V under normal condition. Increase V4 from 0 V gradually. The V4 voltage when I1 = 10 µA is DO'H' voltage (VD0 (H)). Set S1=OFF, S2=ON, V1=V2=3.6 V, and V3=0.5 V under overcurrent condition. Increase V5 from 0 V gradually. The V5 voltage when I2 = 10 µA is the DO'L' voltage (VDO (L)). (7) Measurement 7 Measurement circuit 4 Set S1=ON, S2=OFF, V1=V2=3.6 V and V3=0 V under normal condition. Increase V4 from 0 V gradually. The V4 voltage when I1 = 10 µA is the CO'H' voltage (VC0 (H)). Set S1=OFF S2=ON, V1=V2=4.7, V3=0V, and V4=9.4V under over voltage condition. (V5)/I2 is the CO pin internal resistance (RCOL). (8) Measurement 8 Measurement circuit 5 Set V1=V2=3.6 V, and V3=0V under normal condition. Increase V1 from (VCU1-0.2V) to (VCU1+0.2V) immediately (within 10 µs). The time after V1 becomes (VCU1+0.2V) until CO goes 'L' is the overcharge detection delay time 1 (tCU1). Set V1=V2=3.5 V, and V3=0V under normal condition. Decrease V1 from (VDD1+0.2V) to (VDD1-0.2V) immediately (within 10 µs). The time after V1 becomes (VDD1-0.2V) until DO goes 'L' is the overdischarge detection delay time 1 (tDD1). (9) Measurement 9 Measurement circuit 5 Set V1=V2=3.6 V , and V3=0V under normal condition. Increase V2 from (VCU2-0.2V) to (VCU2+0.2V) immediately (within 10 µs). The time after V2 becomes (VCU2+0.2V) until CO goes 'L' is the overcharge detection delay time 2 (tCU2). Set V1=V2=3.6 V , and V3=0V under normal condition. Decrease V2 from (VDD2+0.2V) to (VDD2-0.2V) immediately (within 10 µs). The time after V2 becomes (VDD2-0.2V) until DO goes 'L' is the overdischarge detection delay time 2 (tDD2). (10) Measurement 10 Measurement circuit 5 Set V1=V2=3.6 V, and V3=0V under normal condition. Increase V3 from 0 V to 0.5 V immediately (within 10 µs). The time after V3 becomes 0.5 V until DO goes 'L' is the overcurrent detection delay time 1 (tI0V1). (11) Measurement 11 Measurement circuit 6 Set V1=V2=0 V, and V3=2 V, and decrease V3 gradually. The V3 voltage when CO = 'L' (VCC- 0.3 V or lower) is the 0V charge starting voltage (V0CHA). (12) Measurement 12 Measurement circuit 6 Set V1=0 V, V2=3.6 V, and V3=12 V, and increase V1 gradually. The V1 voltage when CO = 'H' (VM+ 0.3 V or higher) is the 0V charge inhibiting voltage 1 (V0INH1). (13) Measurement 13 Measurement circuit 6 Set V1=3.6 V, V2=0 V, and V3=12 V, and increase V2 gradually. The V2 voltage when CO = 'H' (VM+ 0.3 V or higher) is the 0V charge inhibiting voltage 2 (V0INH2). 8 Seiko Instruments Inc. Battery Protection IC (for a 2-serial-cell pack) S-8232 Series Rev.3.0 SENS SENS VCC VCC V1 V1 ICT VC ICT VC S1 S-8232Series V2 S-8232Series V2 VM VSS DO VM VSS CO DO CO V3 V3 V5 Measurement circuit 1 V4 S2 I2 S1 I1 Measurement circuit 4 SENS I1 VCC V1 SENS ICT C3=0.22µF VC VCC S-8232Series V2 VM VSS DO VC CO S-8232Series V2 VM VSS I2 V3 C3 ICT V1 DO CO S1 V3 Measurement circuit 2 Measurement circuit 5 SENS VCC V1 SENS ICT VC VCC S-8232Series V2 VM VSS DO V1 ICT VC CO S-8232Series V2 V5 V4 S2 I2 S1 I1 VM VSS V3 DO V3 CO 4.7MΩ Measurement circuit 6 Measurement circuit 3 Seiko Instruments Inc. 9 Battery Protection IC (for a 2-serial-cell pack) S-8232 Series Rev.2.0 Description Normal condition(*1, 3) This IC monitors the voltages of the two serially-connected batteries and the discharge current to control charging and discharging. If the voltages of all the two batteries are in the range from the overdischarge detection voltage (VDD1,2) to the overcharge detection voltage (VCU1,2), and the current flowing through the batteries becomes equal or lower than a specified value (the VM terminal voltage is equal or lower than overcurrent detection voltage 1), the charging and discharging FET’s turn on. In this condition, charging and discharging can be carried out freely. This condition is called the normal condition. In this condition, the VM and VSS terminals are shorted by the Rvsm resistor. Overcurrent condition This IC is provided with the two overcurrent detection levels (VIOV1 and VIOV2) and the two overcurrent detection delay time (tIOV1 and tIOV2) corresponding to each overcurrent detection level. If the discharging current becomes equal to or higher than a specified value (the VM terminal voltage is equal to or higher than the overcurrent detection voltage) during discharging under normal condition and it continues for the overcurrent detection delay time (tIOV) or longer, the discharging FET turns off to stop discharging. This condition is called an overcurrent condition. The VM and VSS terminals are shorted by the Rvsm resistor at this time. The charging FET turns off. When the discharging FET is off and a load is connected, the VM terminal voltage equals the VCC potential. The overcurrent condition returns to the normal condition when the load is released and the impedance between the EB- and EB+ terminals (see Figure 6 for a connection example) is 200MΩ or higher. When the load is released, the VM terminal, which and the VSS terminal are shorted with the Rvsm resistor, goes back to the VSS potential. The IC detects that the VM terminal potential returns to overcurrent detection voltage 1 (VIOV1) or lower and returns to the normal condition. Overcharge condition The overcharge condition is detected in two cases: 1) If one of the battery voltages becomes higher than the overcharge detection voltage (VCU1,2) during charging under normal condition and it continues for the overcharge detection delay time (tCU1,2) or longer, the charging FET turns off to stop charging. 2) If one of the battery voltages becomes higher than the auxiliary overcharge detection voltage (VCUaux1,2) the charging FET turns off immediately to stop charging. The VM and VSS terminals are shorted by the Rvsm resistor under the overcharge condition. The auxiliary overcharge detection voltage (VCUaux1,2) is fixed internally and calculated by the overcharge detection voltage (VCU1,2) as follows: VCUaux1,2 [V] = 1.25×VCU1,2 [V] [ For without Overcharge detection / release hysteresis type (VCU1,2 = VCD1,2)] VCUaux1,2 [V] = 1.11×VCU1,2 [V] 10 Seiko Instruments Inc. Battery Protection IC (for a 2-serial-cell pack) S-8232 Series Rev.3.0 The overcharge condition is released in two cases: 1) The battery voltage which exceeded the overcharge detection voltage (VCU1,2) falls below the overcharge release voltage (VCD1,2), the charging FET turns on and the normal condition returns. 2) If the battery voltage which exceeded the overcharge detection voltage (VCU1,2) is equal or higher than the overcharge release voltage (VCD1,2), but the charger is removed, a load is placed, and discharging starts, the charging FET turns on and the normal condition returns. The release mechanism is as follows: the discharge current flows through an internal parasitic diode of the charging FET immediately after a load is installed and discharging starts, and the VM terminal voltage decreases by about 0.6 V from the VSS terminal voltage momentarily. The IC detects this voltage (overcurrent detection voltage 1 or higher), releases the overcharge condition and returns to the normal condition. Overdischarge condition If any one of the battery voltages falls below the overdischarge detection voltage (VDD1,2) during discharging under normal condition and it continues for the overdischarge detection delay time (tDD1,2) or longer, the discharging FET turns off and discharging stops. This condition is called the overdischarge condition. When the discharging FET turns off, the VM terminal voltage becomes equal to the VCC voltage and the IC's current consumption falls below the power-down current consumption (IPDN). This condition is called the power-down condition. The VM and VCC terminals are shorted by the Rvcm resistor under the overdischarge and power-down conditions. The power-down condition is canceled when the charger is connected and the voltage between VM and VCC is overcurrent detection voltage 2 or higher. When all the battery voltages becomes equal to or higher than the overdischarge release voltage (VDU1,2) in this condition, the overdischarge condition changes to the normal condition. Delay circuits The overcharge detection delay time (tCU1,2), overdischarge detection delay time (tDD1,2), and overcurrent detection delay time 1 (tI0V1) are changed with external capacitor (C3).The delay time for overcharge and overdischarge and overcurrent detection is changed via an external capacitor. Those three detection delay times are consistent with each other, describe as below. Overcharge delay time : Overdischarge delay time: Overcurrent delay time = 100 : 10 : 1 The delay times are calculated by the following equations: (Ta=-40 to +85°C) Overcharge detection delay time Min Typ. Max. tCU[S] =Delay factor ( 2.500, 4.545, 9.364 )×C3 [uF] Overdischarge detection delay time tDD[S] =Delay factor ( 0.3045, 0.4545, 0.6409 )×C3 [uF] Overcurrent detection delay time tIOV1[S]=Delay factor ( 0.02864, 0.04545, 0.06682 )×C3 [uF] Note: The delay time for overcurrent detection 2 is fixed by an internal IC circuit. The delay time cannot be changed via an external capacitor. Seiko Instruments Inc. 11 Battery Protection IC (for a 2-serial-cell pack) S-8232 Series Rev.3.0 0V battery charging function (*2) This function is used to recharge both of two serially-connected batteries after they self-discharge to 0V. When the 0V charging start voltage (V0CHA) or higher is applied to between VM and VCC by connecting the charger, the charging FET gate is fixed to VCC potential. When the voltage between the gate sources of the charging FET becomes equal to or higher than the turn-on voltage by the charger voltage, the charging FET turns on to start charging. At this time, the discharging FET turns off and the charging current flows through the internal parasitic diode in the discharging FET. If all the battery voltages become equal to or higher than the overdischarge release voltage (VDU1,2), the normal condition returns. 0 V battery charge inhibiting function (*2) This function is used for inhibiting charging when either of the connected batteries goes 0 V due to its self-discharge. When the voltage of either of the connected batteries goes below 0 V charge inhibit voltage 1 and 2 (VOINH1, 2), the charging FET gate is fixed to "EB -" to inhibit charging. Charging is possible only when the voltage of both connected batteries goes 0 V charge inhibit voltage 1 and 2 (VOINH1, 2) or more. Note that charging may be possible when the total voltage of both connected batteries is less than the minimum value (VDSOP min) of the operating voltage between VCC-VSS even if the voltage of either of the connected batteries is 0 V charge inhibit voltage 1 and 2 (V0INH1, 2) or less. Charging is prohibited when the total voltage of both connected batteries reaches the minimum value (VDSOPmin) of the operating voltage between VCC-VSS. When using this optional function, a resistor of 4.7 MΩ is needed between the gate and the source of the charging control FET (refer to Figure 6). (*1) When initially connecting batteries, the IC may fail to enter the normal condition (discharging ready state). If so, once set the VM pin to VSS voltage (short pins VM and VSS or connect a charger). (*2) Some lithium ion batteries are not recommended to be recharged after having been completely discharged. Please contact the battery manufacturer when you decide to select a 0 V battery charging function. (*3) The products indicated with *4 in the Selection Guide (model name/item) are set to "overcharge detection/release hysteresis," "no final overcharge function," and "0 V battery charge inhibiting function." The following phenomena may be found, but there is no problem for practical use. The product is an overcurrent condition due to overload connection when the battery voltage is overcharge release voltage (VCD1, 2) or more and overcharge detection voltage (VCU1, 2) or less. Usually, the IC returns to its normal condition when overload is removed under this condition. However, the charging FET may be turned OFF when overload is removed under this condition, leading to an overcharge condition. If so, attach load to start discharge. The charging FET is turned ON to return to the normal condition. Refer to "OverCharge Condition" of Description Section. 12 Seiko Instruments Inc. Battery Protection IC (for a 2-serial-cell pack) S-8232 Series Rev.3.0 Operation Timing Charts 1. Overcharge detection V1 battery Vcuaux V2 battery Vcu Vcd Battery voltage Vdu Vdd Vss Vcc DO terminal Vss V2 Over voltage detect V1 Over voltage detect Vcc CO terminal V1 auxiliary V2 auxiliary over voltage detect over voltage detect Vss EBVcc Viov2 VM terminal Viov1 Vss EB- Charger connected Load connected Mode Note: Delay c Delay d c d c d c d c cNormal mode, dOver charge mode,eOver discharge mode, fover current mode The charger is assumed to charge with a constant current. Figure 3 Seiko Instruments Inc. 13 Battery Protection IC (for a 2-serial-cell pack) S-8232 Series Rev.3.0 2. Overdischarge detection Vcu V1 battery V2 battery Vcd Battery voltage Vdu Vdd Vss Vcc DO terminal Vss Vcc CO terminal Vss EBVcc VM terminal Viov2 Viov1 Vss EB- Charger connected Load connecte d Mode Note: Delay Delay Delay c e c e cNormal mode, dOver charge mode,eOver discharge mode, fover current mode c&e The charger is assumed to charge with a constant current. Figure 4 3. Overcurrent detection V1,V2 battery Vcu Vcd Battery voltage Vdu Vdd Vcc DO terminal Vss Vcc CO terminal Vss EBVcc Viov2 VM terminal Viov1 Vss EB- Charger connected Load connected Mode Note: Delay = t IOV2 Delay = t IOV1 c f c cNormal mode, dOver charge mode,eOver discharge mode, fover current mode delay < t IOV1 f The charger is assumed to charge with a constant current. Figure 5 14 Seiko Instruments Inc. c Battery Protection IC (for a 2-serial-cell pack) S-8232 Series Rev.3.0 Battery Protection IC Connection Example EB + R 4 1 KΩ SENS R 1 1 KΩ VCC Battery 1 C1 0.22 µ F R 2 1 KΩ S-8232 series VC Battery 2 C2 0.22 µ F C3 VSS ICT CO DO Delay time adjustment VM 0.22 µ F R3 R5 FET2 FET1 EB - 1KΩ 4.7MΩ Figure 6 Table 7 Constant Symbol Parts Purpose Recommend min. max. FET1 Nch MOSFET Charge control ----- ----- ----- ----- FET2 Nch MOSFET Discharge control ----- ----- ----- ----- R1 Chip resistor For ESD 1KΩ 300Ω 1KΩ C1 Chip capacitor Filter 0.22µF 0µF 1µF R2 Chip resistor For ESD 1KΩ 300Ω 1KΩ C2 Chip capacitor Filter 0.22µF 0µF 1µF R4 Chip resistor For ESD 1KΩ =R1min =R1max C3 Chip capacitor Setting delay time 0.22µF 0µF 1µF *2) Note leak current of C2 R3 Chip resistor Protection at reverse 1KΩ 300Ω 5KΩ *3) Discharge can’t be stopped at connecting of a Chip resistor 0V battery charging *1) Put same value resistor=R1,R2 less than 300Ω when a charger is charger R5 Remarks connected in reverse. (4.7MΩ) (1MΩ) (10MΩ) prevent *4) lower resistor increase current consumption Seiko Instruments Inc. 15 Battery Protection IC (for a 2-serial-cell pack) S-8232 Series * 1) R4 =R1 is required. Overcharge detection voltage is increased by R4. For example 10KW (R4) increase overcharge detection voltage by 20mV. * 2) The overcharge detection delay time(tCU), the overdischarge detection delay time(tCD), and the over current detection delay time(tIOV) are changed with external capacitor C3. See the electrical characteristics. * 3) R3 is necessary to protect the IC when the charger is connected in reverse. Connect 300Wor more. But excessive R3 causes increasing of Overcurrent detection voltage 1 (VIOV1). Please refer the following formulation. D VIOV1=(R3+Rvsm)/Rvsm×VIOV1-VIOV1 Foe example 50kW(R3) increase Overcurrent detection voltage 1 (VIOV1=0.100V) by 13mV. * 4) 4.7M W(R5)prevents 0V battery from charging. Current consumption is increased by R5. Please connect R5 for only 0V charging unavailable type. !Note: The above connection diagram and constants do not guarantee proper operations. Evaluate your actual application and set constants properly. 16 Seiko Instruments Inc. Rev.3.0 Battery Protection IC (for a 2-serial-cell pack) S-8232 Series Rev.3.0 Precautions (1) After the overcurrent detection delay, if the battery voltages is equals the overdischarge detection voltage(VDD1,2) or lower, the overdischarge detection delay time becomes shorter than 10mS(min.). It occurs because capacitor C3 sets all of delay times. (Refer fig.7) [ Cause ] Vcu It occurs because capacitor C3 sets all of delay times. When overcurrent detection is Battery Vcd voltage Vdu released until tIOV1 , the capacitor C3 is Vdd been charging by S-8232. IF all batteries voltage is lower than VDD1,2 at that time, charging goes on. So delay time is shorter The battery voltages is equal to or less the over discharge voltage. Vcc the over discharge detection DO terminal Vss then typical. Vcc VM [ Conclusion ] Viov2 The over current returns to normal current. terminal Viov1 Vss This phenomenon occurs when all batteries voltage is nearly equal to the overdischarge The over current delay Load connect voltage(VDD1,2) after overcurrent detected. The over discharge delay The delay time becomes shorter than usual. It means that the batteries capacity is small Figure 7 and those must be charged in the future. Even if the state change to overdischarge condition , the battery package capacity is same as typical. (2) When one of the battery voltages is overdischarge detection voltage(VDD1,2) or lower and the other one becomes higher than the overcharge detection voltage(VCU1,2), the IC detects the overcharge without the overcharge detection delay time(tCU). (Refer fig.8) [ Cause ] It is same as the overdischarge detection under the overcurrent condition. It occurs Vcu Battery 1 voltage because capacitor C3 sets all of delay Vcd Vdu Over voltage detect Over discharge state Vdd times. Vcu [ Conclusion ] This phenomenon occurs when one battery Battery 2 voltage Vcd Vdu Vdd voltage is lower than overdischarge voltage(VDD1,2) and batteries are charged by charger. Under this situation voltage difference between two batteries is unusual. Vcc CO terminal Vss EB- With out delay time is better than long delay time for battery pack safety.(Refer fig.8) Delay time = 0 Charger connected Figure 8 Seiko Instruments Inc. 17 Battery Protection IC (for a 2-serial-cell pack) S-8232 Series Rev.3.0 (3) After the overcurrent detection, the load was connected for a long time, even if one of the battery voltage became lower than overdischarge detection voltage (VDD1,2), the IC can’t detects the overdischarge as long as the load is connected. Therefor the IC’s current consumption at the one of the battery voltage is lower than the overdischarge detection voltage is same as normal condition current consumption (IOPE) . (Refer fig.9) [ Cause ] The reason is as follows. If the overcurrent detection and overdischarge detection occur at The battery voltages is less than the over discharge voltage, by self current consumption. Battery voltage Vdd 0V same time, the overcurrent detection takes As long as the load is connected, the IC’s current consumption is same as normal current consumption (Iope). precedence the overdischarge detection. As long as the IC detects overcurrent, the IC can’t Current Consumption detect overdischarge. DO [ Conclusion ] Iope Ipdn 0A Vcc terminal Vss If the load take off at least one time, the overcurrent release and the overdischarge detection works. VM terminal Unless keep the IC(S-8232) with load for a long time, the reduction of battery voltage will be Vcc Viov2 Viov1 Vss EBLoad connect neglected, because of the IC’s(S-8232) current consumption(typ. 7.5uA) is small. 18 Seiko Instruments Inc. The over current delay Figure 9 Battery Protection IC (for a 2-serial-cell pack) S-8232 Series Rev.3.0 Characteristics(typical characteristics) 1. Detection voltage temperature characteristics Overcharge detection voltage1 vs.temperature Overcharge detection voltage2 vs.temperature VCU2=4.30 [V] VCU1=4.30 [V] 4.4 4.4 VCU 1 [V] 4.3 VCU2 [V] 4.3 4.2 -40 -20 0 20 40 60 80 100 4.2 -40 -20 0 20 Ta [°C] Overcharge release voltage1 vs.temperature VCD 1=4.00 [V] 80 100 4.1 VCD2 [V] VCD 1 4 [V] -20 0 20 40 60 80 100 4 3.9 -40 -20 0 20 Ta [°C] 40 60 80 100 Ta [°C] Auxiliary overcharge detection voltage1 vs.temp. VCUaux1=5.375[V] 5.45 Auxiliary overcharge detection voltage2 vs.temp. VCUaux2=5.375[V] 5.45 VCUaux2 [V] VCUaux 1 [V] 5.35 5.25 -40 60 Overcharge release voltage2 vs.temperature VCD2=4.00[V] 4.1 3.9 -40 40 Ta [°C] 5.35 -20 0 20 40 60 80 100 5.25 -40 Ta [°C] -20 0 20 40 60 80 100 Ta [°C] Seiko Instruments Inc. 19 Battery Protection IC (for a 2-serial-cell pack) S-8232 Series Overdischarge detection voltage1 vs.temperature VDD1=2.00 [V] 2.1 Overdischarge detection voltage2 vs.temperature VDD2=2.00 [V] 2.1 VDD1 2 [V] 1.9 -40 Rev.3.0 VDD2 2 [V] -20 0 20 40 60 80 100 1.9 -40 -20 0 20 Ta [°C] Overdischarge release voltage1 vs.temperature VDU1=2.60 [V] 2.7 VDU 1 [V] 2.6 VDU2 [V] 2.6 -20 0 20 40 60 80 100 Overdischarge release voltage1 vs.temperature VDU2=2.60 [V] 2.7 2.5 -40 40 Ta [°C] 60 80 100 2.5 -40 -20 0 20 40 60 80 100 Ta [°C] Ta [°C] Overcurrent1 detection voltage vs.temperature VIOV1=0.1 [V] Overcurrent1 detection voltage vs.temperature VIOV2=-1.20 [V] (VCC reference) 0.12 -1.10 VIOV1 [V] 0.10 VIOV2 [V] -1.20 -1.15 -1.25 0.08 -40 -1.30 -20 0 20 40 60 80 100 -40 -20 Ta [°C] 20 0 20 40 Ta [°C] Seiko Instruments Inc. 60 80 100 Battery Protection IC (for a 2-serial-cell pack) S-8232 Series Rev.3.0 2.Current consumption temperature characteristics Current consumption vs. temperature in normal mode Current consumption vs. temperature in power-down mode VCC=7.2 [V] VCC=3.0 [V] 15 100 10 IPDN [nA] 50 I OPE [uA] 5 0 -40 -20 0 20 40 60 80 0 -40 100 -20 0 20 Ta [°C] 40 60 80 100 Ta [°C] 3. Delay time temperature characteristics Overcharge detecion1 time vs.temparature Overcharge detecion1 time vs.temparature C3=0.22 [uF] C3=0.22 [uF] 1.5 150 TDD [mS] 100 tCU 1 [S] 0.5 -40 -20 0 20 40 60 80 50 -40 100 -20 Ta [°C] 0 20 40 60 80 100 Ta [°C] Overcurrent1 detection time vs.temperature C3=0.22 [uF] 12 11 tIOV1 [mS] 10 9 8 7 -40 -20 0 20 40 60 80 100 T a [°C] * Please design all applications of the S-8232 Series with safety. Seiko Instruments Inc. 21 FT008-A 990531 8-pin TSSOP Dimensions Unit:mm 3.00 +0.3 -0.2 0.17±0.05 0.2 0.1 0.65 Taping Specifications Reel Specifications 1 reel holds 3000 ICs. 4.0±0.1(50 pitches 200±0.3) 2.0±0.05 1.55±0.05 0.3±0.05 R135 8.0±0.1 7 max. 1.55 +0.1 -0 1.4±0.1 (6.9) 4.0 6.6 13.4±1.0 Winding core +0.4 -0.2 17.5±1.0 ø21±0.8 Feed direction 2±0.5 ø13±0.5 8232 Markings 8-pin TSSOP (1) (2) (3) (4) (5) (6) (7) 990603 • • • • • • The information described herein is subject to change without notice. Seiko Instruments Inc. is not responsible for any problems caused by circuits or diagrams described herein whose related industrial properties, patents, or other rights belong to third parties. The application circuit examples explain typical applications of the products, and do not guarantee the success of any specific mass-production design. When the products described herein are regulated products subject to the Wassenaar Arrangement or other agreements, they may not be exported without authorization from the appropriate governmental authority. Use of the information described herein for other purposes and/or reproduction or copying without the express permission of Seiko Instruments Inc. is strictly prohibited. The products described herein cannot be used as part of any device or equipment affecting the human body, such as exercise equipment, medical equipment, security systems, gas equipment, or any apparatus installed in airplanes and other vehicles, without prior written permission of Seiko Instruments Inc. Although Seiko Instruments Inc. exerts the greatest possible effort to ensure high quality and reliability, the failure or malfunction of semiconductor products may occur. The user of these products should therefore give thorough consideration to safety design, including redundancy, fire-prevention measures, and malfunction prevention, to prevent any accidents, fires, or community damage that may ensue.