a FEATURES Wide Bandwidth AD8047, G = +1 AD8048, G = +2 Small Signal 250 MHz 260 MHz Large Signal (2 V p-p) 130 MHz 160 MHz 5.8 mA Typical Supply Current Low Distortion, (SFDR) Low Noise –66 dBc typ @ 5 MHz –54 dBc typ @ 20 MHz 5.2 nV/√Hz (AD8047), 3.8 nV/√Hz (AD8048) Noise Drives 50 pF Capacitive Load High Speed Slew Rate 750 V/µs (AD8047), 1000 V/µs (AD8048) Settling 30 ns to 0.01%, 2 V Step ±3 V to ±6 V Supply Operation APPLICATIONS Low Power ADC Input Driver Differential Amplifiers IF/RF Amplifiers Pulse Amplifiers Professional Video DAC Current to Voltage Conversion Baseband and Video Communications Pin Diode Receivers Active Filters/Integrators PRODUCT DESCRIPTION 250 MHz, General Purpose Voltage Feedback Op Amps AD8047/AD8048 FUNCTIONAL BLOCK DIAGRAM 8-Pin Plastic Mini-DIP (N), Cerdip (Q) and SO (R) Packages NC 1 8 NC –INPUT 2 7 +VS +INPUT 3 6 OUTPUT 5 NC –V S 4 AD8047/48 (Top View) NC = NO CONNECT The AD8047 and AD8048’s low distortion and cap load drive make the AD8047/AD8048 ideal for buffering high speed ADCs. They are suitable for 12 bit/10 MSPS or 8 bit/60 MSPS ADCs. Additionally, the balanced high impedance inputs of the voltage feedback architecture allow maximum flexibility when designing active filters. The AD8047 and AD8048 are offered in industrial (–40°C to +85°C) temperature ranges and are available in 8-pin plastic DIP and SOIC packages. The AD8047 and AD8048 are very high speed and wide bandwidth amplifiers. The AD8047 is unity gain stable. The AD8048 is stable at gains of two or greater. The AD8047 and AD8048, which utilize a voltage feedback architecture, meet the requirements of many applications that previously depended on current feedback amplifiers. A proprietary circuit has produced an amplifier that combines many of the best characteristics of both current feedback and voltage feedback amplifiers. For the power (6.6 mA max) the AD8047 and AD8048 exhibit fast and accurate pulse response (30 ns to 0.01%) as well as extremely wide small signal and large signal bandwidth and low distortion. The AD8047 achieves –54 dBc distortion at 20 MHz and 250 MHz small signal and 130 MHz large signal bandwidths. 1V 5ns Figure 1. AD8047 Large Signal Transient Response, VO = 4 V p-p, G = +1 REV. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. © Analog Devices, Inc., 1995 One Technology Way, P.O. Box 9106, Norwood. MA 02062-9106, U.S.A. Tel: 617/329-4700 Fax: 617/326-8703 AD8047/AD8048–SPECIFICATIONS ELECTRICAL CHARACTERISTICS (±V = ±5 V; R S Parameter DYNAMIC PERFORMANCE Bandwidth (–3 dB) Small Signal Large Signal1 Bandwidth for 0.1 dB Flatness Slew Rate, Average +/– Rise/Fall Time Settling Time To 0.1% To 0.01% HARMONIC/NOISE PERFORMANCE 2nd Harmonic Distortion 3rd Harmonic Distortion Input Voltage Noise Input Current Noise Average Equivalent Integrated Input Noise Voltage Differential Gain Error (3.58 MHz) Differential Phase Error (3.58 MHz) LOAD = 100 Ω; AV = 1 (AD8047); AV = 2 (AD8048), unless otherwise noted) Conditions VOUT ≤ 0.4 V p-p VOUT = 2 V p-p VOUT = 300 mV p-p 8047, RF = 0 Ω; 8048, RF = 200 Ω VOUT = 4 V Step VOUT = 0.5 V Step VOUT = 4 V Step AD8047A Min Typ Max AD8048A Min Typ Max Units 170 100 180 135 260 160 MHz MHz 50 1000 1.2 3.2 MHz V/µs ns ns 475 250 130 35 750 1.1 4.3 VOUT = 2 V Step VOUT = 2 V Step 13 30 13 30 ns ns 2 V p-p; 20 MHz RL = 1 kΩ 2 V p-p; 20 MHz RL = 1 kΩ f = 100 kHz f = 100 kHz –54 –64 –60 –61 5.2 1.0 –48 –60 –56 –65 3.8 1.0 dBc dBc dBc dBc nV/√Hz pA/√Hz 0.1 MHz to 10 MHz RL = 150 Ω, G = +2 RL = 150 Ω, G = +2 16 0.02 0.03 11 0.01 0.02 µV rms % Degree DC PERFORMANCE2, RL = 150 Ω Input Offset Voltage3 1 TMIN –TMAX ±5 1 Offset Voltage Drift Input Bias Current TMIN –TMAX Input Offset Current Common-Mode Rejection Ratio Open-Loop Gain 740 0.5 TMIN –TMAX VCM = ± 2.5 V VOUT = ± 2.5 V TMIN –TMAX 74 58 54 INPUT CHARACTERISTICS Input Resistance Input Capacitance Input Common-Mode Voltage Range OUTPUT CHARACTERISTICS Output Voltage Range, RL = 150 Ω Output Current Output Resistance Short Circuit Current POWER SUPPLY Operating Range Quiescent Current 1 ±5 1 3.5 6.5 2 3 80 62 0.5 74 65 56 3 4 3.5 6.5 2 3 80 68 mV mV µV/°C µA µA µA µA dB dB dB 500 1.5 ± 3.4 500 1.5 ± 3.4 kΩ pF V ± 2.8 ± 3.0 50 0.2 130 ± 2.8 ± 3.0 50 0.2 130 V mA Ω mA ± 3.0 ± 5.0 ± 6.0 5.8 6.6 7.5 78 ± 3.0 ± 5.0 ± 6.0 5.9 6.6 7.5 72 78 V mA mA dB TMIN –TMAX Power Supply Rejection Ratio 3 4 72 NOTES 1 See Max Ratings and Theory of Operation sections of data sheet. 2 Measured at AV = 50. 3 Measured with respect to the inverting input. Specifications subject to change without notice. –2– REV. 0 AD8047/AD8048 ABSOLUTE MAXIMUM RATINGS 1 MAXIMUM POWER DISSIPATION Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.6 V Voltage Swing × Bandwidth Product (AD8047) . . . 180 V – MHz (AD8048) . . . 250 V – MHz Internal Power Dissipation2 Plastic Package (N) . . . . . . . . . . . . . . . . . . . . . . . . 1.3 Watts Small Outline Package (R) . . . . . . . . . . . . . . . . . . . 0.9 Watts Input Voltage (Common Mode) . . . . . . . . . . . . . . . . . . . . ± VS Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . ± 1.2 V Output Short Circuit Duration . . . . . . . . . . . . . . . . . . . . . . Observe Power Derating Curves Storage Temperature Range (N, R) . . . . . . . . –65°C to +125°C Operating Temperature Range (A Grade) . . . –40°C to +85°C Lead Temperature Range (Soldering 10 sec) . . . . . . . . +300°C The maximum power that can be safely dissipated by these devices is limited by the associated rise in junction temperature. The maximum safe junction temperature for plastic encapsulated devices is determined by the glass transition temperature of the plastic, approximately +150°C. Exceeding this limit temporarily may cause a shift in parametric performance due to a change in the stresses exerted on the die by the package. Exceeding a junction temperature of +175°C for an extended period can result in device failure. While the AD8047 and AD8048 are internally short circuit protected, this may not be sufficient to guarantee that the maximum junction temperature (+150°C) is not exceeded under all conditions. To ensure proper operation, it is necessary to observe the maximum power derating curves. NOTES 1 Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2 Specification is for device in free air: 8-Pin Plastic DIP Package: θ JA = 90°C/Watt 8-Pin SOIC Package: θJA = 140°C/Watt MAXIMUM POWER DISSIPATION – Watts 2.0 METALIZATION PHOTOS Dimensions shown in inches and (mm). Connect Substrate to –V S. AD8047 +VS 8-PIN MINI-DIP PACKAGE TJ = +150°C 1.5 1.0 8-PIN SOIC PACKAGE 0.5 0 –50 –40 –30 –20 –10 0 10 20 30 40 50 60 AMBIENT TEMPERATURE – °C 70 80 90 Figure 2. Plot of Maximum Power Dissipation vs. Temperature 0.045 (1.14) VOUT ORDERING GUIDE –IN –VS +IN Temperature Range Package Package Description Option* AD8047AN AD8047AR AD8047-EB –40°C to +85°C –40°C to +85°C AD8048AN AD8048AR AD8048-EB –40°C to +85°C –40°C to +85°C Plastic DIP SOIC Evaluation Board Plastic DIP SOIC Evaluation Board Model 0.044 (1.13) AD8048 +VS 0.045 –OUT (1.14) N-8 R-8 N-8 R-8 *N = Plastic DIP; R= SOIC (Small Outline Integrated Circuit) –IN +IN –VS 0.044 (1.13) CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although these devices feature proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. REV. 0 –3– WARNING! ESD SENSITIVE DEVICE AD8047/AD8048 AD8047–Typical Characteristics RF 10µF +VS PULSE GENERATOR 7 2 AD8047 TR /TF = 500ps VIN 3 TR/TF = 500ps 6 4 0.1µF RIN VIN VOUT 0.1µF 2 3 10µF RT = 49.9Ω 7 AD8047 RT = 66.5Ω RL = 100Ω 10µF +VS PULSE GENERATOR 0.1µF VOUT 6 0.1µF 4 100Ω RL = 100Ω 10µF –VS –V S Figure 3. Noninverting Configuration, G = +1 1V Figure 6. Inverting Configuration, G = –1 5ns 1V Figure 4. Large Signal Transient Response; VO = 4 V p-p, G = +1 100mV 5ns Figure 7. Large Signal Transient Response; VO = 4 V p-p, G = –1, RF = RIN = 200 Ω 5ns 100mV Figure 5. Small Signal Transient Response; VO = 400 mV p-p, G = +1 5ns Figure 8. Small Signal Transient Response; VO = 400 mV p-p, G = –1, RF = RIN = 200 Ω –4– REV. 0 AD8047/AD8048 AD8048–Typical Characteristics RF PULSE GENERATOR 10µF +V S TR/T F = 500ps 2 RIN VIN AD8048 3 0.1µF TR/TF = 500ps 7 VOUT 6 2 RT = 49.9Ω 3 RL = 100Ω RL = 100Ω –VS Figure 9. Noninverting Configuration, G = +2 Figure 12. Inverting Configuration, G= –1 1V 5ns Figure 10. Large Signal Transient Response; VO = 4 V p-p, G = +2, RF = RIN = 200 Ω 5ns Figure 13. Large Signal Transient Response; VO = 4 V p-p, G = –1, RF = RIN = 200 Ω 5ns 100mV Figure 11. Small Signal Transient Response; VO = 400 mV p-p, G = +2, RF = RIN = 200 Ω REV. 0 4 10µF –VS 100mV VOUT 6 0.1µF RS = 100Ω 10µF 1V 7 AD8048 RT = 66.5Ω 0.1µF 4 10µF +VS PULSE GENERATOR 0.1µF RIN VIN RF 5ns Figure 14. Small Signal Transient Response; VO = 400 mV p-p, G = –1, RF = RIN = 200 Ω –5– AD8047/AD8048 AD8047–Typical Characteristics 1 0 –1 –1 –3 RL = 100Ω RF = 0Ω FOR DIP RF = 66.5Ω FOR SOIC VOUT = 300mV p-p –2 OUTPUT – dBm –2 OUTPUT – dBm 1 0 –4 –5 –6 –3 RL = 100Ω RF = 0Ω FOR DIP RF = 66.5Ω FOR SOIC VOUT = 2V p-p –4 –5 –6 –7 –7 –8 –8 –9 1M 10M 100M –9 1M 1G 10M FREQUENCY – Hz Figure 15. AD8047 Small Signal Frequency Response G = +1 1 0 0 –0.1 –1 RL = 100Ω RF = 0Ω FOR DIP RF = 66.5Ω FOR SOIC VOUT = 300mV p-p –2 OUTPUT – dBm OUTPUT – dBm –0.3 –0.4 –0.5 –0.6 –3 RL = 100Ω RF = RIN = 200Ω VOUT = 300mV p-p –4 –5 –6 –0.7 –7 –0.8 –8 –0.9 1M 10M 100M –9 1M 1G 10M FREQUENCY – Hz 70 100 60 80 30 20 GAIN 0 –20 10 –40 0 RL = 100Ω –10 –60 –20 –80 –30 10k 100k 1M 10M 100M RL = 1kΩ VOUT = 2V p-p –40 –50 OUTPUT – dBm 40 PHASE MARGIN – Degrees GAIN – dB –20 60 40 20 1G Figure 19. AD8047 Small Signal Frequency Response, G = –1 –30 PHASE MARGIN 50 100M FREQUENCY – Hz Figure 16. AD8047 0.1 dB Flatness, G = +1 1k 1G Figure 18. AD8047 Large Signal Frequency Response, G = +1 0.1 –0.2 100M FREQUENCY – Hz –60 –70 2ND HARMONIC –80 –90 3RD HARMONIC –100 –110 –100 1G –120 10k FREQUENCY – Hz 100k 1M 10M 100M FREQUENCY – Hz Figure 17. AD8047 Open-Loop Gain and Phase Margin vs. Frequency Figure 20. AD8047 Harmonic Distortion vs. Frequency, G = +1 –6– REV. 0 AD8047/AD8048 –20 0.5 RL = 100Ω VOUT = 2V p-p RL = 100Ω RF = 0Ω VOUT = 2V STEP 0.4 –40 0.3 –50 0.2 –60 –70 ERROR – % HARMONIC DISTORTION – dBc –30 2ND HARMONIC –80 –90 0.1 0.0 –0.1 –0.2 3RD HARMONIC –100 –0.3 –110 –0.4 –120 10k 100k 10M 1M –0.5 100M 0 5 10 FREQUENCY – Hz Figure 21. AD8047 Harmonic Distortion vs. Frequency, G = +1 0.15 0.10 –40 –45 3RD HARMONIC –50 0.00 –0.05 –0.10 –0.15 2ND HARMONIC –0.20 –0.25 2.5 3.5 4.5 OUTPUT SWING – V p-p 5.5 6.5 0 2 4 8 6 10 12 SETTLING TIME – µs 14 16 18 Figure 25. AD8047 Long-Term Settling Time, G = +1 Figure 22. AD8047 Harmonic Distortion vs. Output Swing, G = +1 17 0.04 0.02 INPUT NOISE VOLTAGE – nV/√Hz DIFF GAIN – % 0.05 –55 –65 1.6 0.00 –0.02 –0.04 1st DIFF PHASE – Degrees 45 RL = 100Ω RF = 0Ω VOUT = 2V STEP 0.20 f = 20MHz RL = 1kΩ RF = 0Ω –60 2nd 3rd 4th 5th 6th 7th 8th 9th 10th 11th 0.04 0.02 0.00 15 13 11 9 7 5 –0.02 –0.04 3 1st 2nd 3rd 4th 5th 6th 7th 8th 9th 10th 11th 10 100 1k FREQUENCY – Hz 10k Figure 26. AD8047 Noise vs. Frequency Figure 23. AD8047 Differential Gain and Phase Error, G = +2, RL = 150 Ω, RF = 200 Ω, RIN = 200 Ω REV. 0 40 0.25 ERROR – % HARMONIC DISTORTION – dBc –35 35 Figure 24. AD8047 Short-Term Settling Time, G = +1 –25 –30 20 15 25 30 SETTLING TIME – ns –7– 100k AD8047/AD8048 AD8048–Typical Characteristics 7 7 6 6 5 4 OUTPUT – dBm OUTPUT – dBm 3 2 1 0 3 2 1 0 –1 –1 –2 –2 –3 –3 1M 10M 100M FREQUENCY – Hz 1G 1M 10M 1 6.4 RL = 100Ω RF = RIN = 200Ω VOUT = 300mV p-p 6.3 0 –1 6.2 OUTPUT – dBm –2 6.1 6.0 5.9 –4 –5 5.8 –6 –7 5.6 –8 5.5 –9 1M 10M 100M 1G RL = 100Ω RF = RIN = 200Ω VOUT = 300mV p-p –3 5.7 1M 10M FREQUENCY – Hz 100 –20 80 80 –30 70 60 HARMONIC DISTORTION – dBc 90 40 50 20 0 40 –20 30 RL = 100Ω 20 –40 10 –60 0 –80 –10 –100 –20 –120 1G 10k 100k 1M 10M FREQUENCY – Hz 100M PHASE – Degrees PHASE 60 100M FREQUENCY – Hz 1G Figure 31. AD8048 Small Signal Frequency Response, G = –1 Figure 28. AD8048 0.1 dB Flatness, G = +2 GAIN – dB 1G Figure 30. AD8048 Large Signal Frequency Response, G = +2 6.5 1k 100M FREQUENCY – Hz Figure 27. AD8048 Small Signal Frequency Response, G = +2 OUTPUT – dBm RL = 100Ω RF = RIN = 200Ω VOUT = 2V p-p 5 RL = 100Ω RF = RIN = 200Ω VOUT = 300mV p-p 4 RL = 1kΩ VOUT = 2V p-p –40 –50 –60 2ND HARMONIC –70 –80 –90 3RD HARMONIC –100 –110 –120 10k Figure 29. AD8048 Open-Loop Gain and Phase Margin vs. Frequency 100k 1M FREQUENCY – Hz 10M 100M Figure 32. AD8048 Harmonic Distortion vs. Frequency, G = +2 –8– REV. 0 AD8047/AD8048 0.5 –20 –40 0.3 –50 0.2 –60 0.1 –70 2ND HARMONIC –80 –0.3 –100 –0.4 –0.5 –120 10k 100k 1M FREQUENCY – Hz 10M 100M –15 10 15 20 25 30 35 40 45 0.25 –30 RL = 100Ω RF = 200Ω VOUT = 2V STEP 0.20 f = 20MHz RL = 1kΩ RF = 200 –25 0.15 3RD HARMONIC 0.10 –35 ERROR – % HARMONIC DISTORTION – dBc 5 Figure 36. AD8048 Short-Term Settling Time, G = +2 –20 –40 –45 –50 2ND HARMONIC –55 0.05 0.0 –0.05 –0.10 –60 –0.15 –65 –0.20 –70 1.5 2.5 3.5 4.5 OUTPUT SWING – Volts p-p 5.5 –0.25 6.5 Figure 34. AD8048 Harmonic Distortion vs. Output Swing, G = +2 0 2 4 8 6 10 12 SETTLING TIME – µs 14 16 18 Figure 37. AD8048 Long-Term Settling Time 2 V Step, G = +2 17 0.04 0.02 INPUT NOISE VOLTAGE – nV/√Hz DIFF GAIN – % 0 SETTLING TIME – ns Figure 33. AD8048 Harmonic Distortion vs. Frequency, G = +2 0.00 –0.02 –0.04 1st DIFF PHASE – Degrees 0.0 –0.1 –0.2 3RD HARMONIC –90 –110 2nd 3rd 4th 5th 6th 7th 8th 9th 10th 11th 0.04 0.02 0.00 15 13 11 9 7 5 –0.02 –0.04 1st 2nd 3rd 4th 5th 6th 7th 8th 9th 3 10th 11th 10 Figure 35. AD8048 Differential Gain and Phase Error, G = +2, RL = 150 Ω, RF = 200 Ω, RIN = 200 Ω REV. 0 RL = 100Ω RF = 200Ω VOUT = 2V STEP 0.4 ERROR – % HARMONIC DISTORTION – dBc –30 RL = 100Ω VOUT = 2V p-p 100 1k FREQUENCY – Hz 10k 100k Figure 38. AD8048 Noise vs. Frequency –9– AD8047/AD8048–Typical Characteristics 100 100 ∆VCM = 1V RL = 100Ω ∆VCM = 1V RL = 100Ω 90 80 80 70 70 CMRR – dB CMRR – dB 90 60 50 40 60 50 40 30 30 20 100k 1M 100M 10M 20 100k 1G FREQUENCY – Hz 1M 10M 1G 100M FREQUENCY – Hz Figure 42. AD8048 CMRR vs. Frequency 100 100 10 10 ROUT – Ω ROUT – Ω Figure 39. AD8047 CMRR vs. Frequency 1 1 0.1 0.1 0.01 10k 100k 1M 10M 100M 0.01 10k 1G 100k 90 90 80 80 +PSRR 1G –PSRR +PSRR 60 50 40 50 40 30 30 20 20 10 10 0 10k 100M 70 –PSRR PSRR – dB PSRR – dB 60 10M Figure 43. AD8048 Output Resistance vs. Frequency, G = +2 Figure 40. AD8047 Output Resistance vs. Frequency, G = +1 70 1M FREQUENCY – Hz FREQUENCY – Hz 0 100k 1M 10M 100M 1G 3k FREQUENCY – Hz 10k 100k 1M 100M 500M FREQUENCY – Hz Figure 41. AD8047 PSRR vs. Frequency Figure 44. AD8048 PSRR vs. Frequency, G = +2 –10– REV. 0 AD8047/AD8048 83.0 4.1 3.9 82.0 RL = 1kΩ +VOUT AD8047 –VOUT 81.0 3.5 CMRR – –dB OUTPUT SWING – Volts 3.7 3.3 +VOUT 3.1 RL = 150Ω –VOUT 80.0 AD8048 79.0 2.9 78.0 2.7 +VOUT 2.5 2.3 –60 –40 –20 77.0 RL = 50Ω –VOUT 0 20 40 60 80 100 JUNCTION TEMPERATURE – °C 120 76.0 –60 140 –40 –20 0 20 40 60 80 100 120 140 JUNCTION TEMPERATURE – °C Figure 45. AD8047/AD8048 Output Swing vs. Temperature Figure 48. AD8047/AD8048 CMRR vs. Temperature 2600 8.0 2400 7.5 AD8048 AD8048 SUPPLY CURRENT – mA OPEN-LOOP GAIN – V/V 2200 2000 1800 1600 1400 AD8048 6.0 ±5V AD8047 5.5 ±5V 5.0 –40 –20 0 20 40 60 80 100 JUNCTION TEMPERATURE – °C 120 4.5 –60 140 Figure 46. AD8047/AD8048 Open-Loop Gain vs. Temperature –40 –20 0 20 40 60 80 100 JUNCTION TEMPERATURE – °C 120 140 Figure 49. AD8047/AD8048 Supply Current vs. Temperature 94 900 92 INPUT OFFSET VOLTAGE – µV 800 90 +PSRR 88 PSRR – –dB AD8047 ±6V 6.5 AD8047 1200 1000 –60 ±6V 7.0 AD8048 86 84 –PSRR AD8048 +PSRR AD8047 82 80 AD8048 600 AD8047 500 400 300 200 AD8047 78 700 –PSRR 76 –60 –40 –20 0 20 40 60 80 100 120 100 –60 140 JUNCTION TEMPERATURE – °C –20 0 20 40 60 80 100 JUNCTION TEMPERATURE – °C 120 140 Figure 50. AD8047/AD8048 Input Offset Voltage vs. Temperature Figure 47. AD8047/AD8048 PSRR vs. Temperature REV. 0 –40 –11– AD8047/AD8048 For general voltage gain applications, the amplifier bandwidth can be closely estimated as: THEORY OF OPERATION General The AD8047 and AD8048 are wide bandwidth, voltage feedback amplifiers. Since their open-loop frequency response follows the conventional 6 dB/octave roll-off, their gain bandwidth product is basically constant. Increasing their closed-loop gain results in a corresponding decrease in small signal bandwidth. This can be observed by noting the bandwidth specification between the AD8047 (gain of 1) and AD8048 (gain of 2). f 3 dB ≅ Feedback Resistor Choice The value of the feedback resistor is critical for optimum performance on the AD8047 and AD8048. For maximum flatness at a gain of 2, RF and RG should be set to 200 Ω for the AD8048. When the AD8047 is configured as a unity gain follower, RF should be set to 0 Ω (no feedback resistor should be used) for the plastic DIP and 66.5 Ω for the SOIC. G=1+ +VS RF This estimation loses accuracy for gains of +2/–1 or lower due to the amplifier’s damping factor. For these “low gain” cases, the bandwidth will actually extend beyond the calculated value (see Closed-Loop BW plots, Figures 15 and 26). As a rule of thumb, capacitor CF will not be required if: (RF iRG ) × CI ≤ where NG is the Noise Gain (1 + RF/RG) of the circuit. For most voltage gain applications, this should be the case. 10µF RF 7 3 CF 0.1µF AD8047/48 6 RTERM 2 4 VOUT 0.1µF II RG –VS 3 Pulse Response 10µF Unlike a traditional voltage feedback amplifier, where the slew speed is dictated by its front end dc quiescent current and gain bandwidth product, the AD8047 and AD8048 provide “on demand” current that increases proportionally to the input “step” signal amplitude. This results in slew rates (1000 V/µs) comparable to wideband current feedback designs. This, combined with relatively low input noise current (1.0 pA/√Hz), gives the AD8047 and AD8048 the best attributes of both voltage and current feedback amplifiers. 0.1µF VOUT AD8047/48 6 2 RG 4 0.1µF RTERM –VS 10µF RF Figure 52. Inverting Operation When the AD8047 is used in the transimpedance (I to V) mode, such as in photodiode detection, the value of RF and diode capacitance (CI) are usually known. Generally, the value of RF selected will be in the kΩ range, and a shunt capacitor (CF) across RF will be required to maintain good amplifier stability. The value of CF required to maintain optimal flatness (<1 dB Peaking) and settling time can be estimated as: [ 2 CF ≅ (2 ωO CI RF – 1)/ωO RF 2 ] 1/2 where ωO is equal to the unity gain bandwidth product of the amplifier in rad/sec, and CI is the equivalent total input capacitance at the inverting input. Typically ωO = 800 × 106 rad/sec (see Open-Loop Frequency Response curve, Figure 17). As an example, choosing RF = 10 kΩ and CI = 5 pF, requires CF to be 1.1 pF (Note: CI includes both source and parasitic circuit capacitance). The bandwidth of the amplifier can be estimated using the CF calculated as: f 3 dB ≅ VOUT Figure 53. Transimpedance Configuration RF RG AD8047 RF +VS 7 CI 10µF Figure 51. Noninverting Operation VIN NG 4 ωO RG VIN G= – ωO R 2π 1+ F RG 1.6 2πR F CF Large Signal Performance The outstanding large signal operation of the AD8047 and AD8048 is due to a unique, proprietary design architecture. In order to maintain this level of performance, the maximum 180 V-MHz product must be observed, (e.g., @ 100 MHz, VO ≤ 1.8 V p-p) on the AD8047 and 250 V-MHz product on the AD8048. Power Supply Bypassing Adequate power supply bypassing can be critical when optimizing the performance of a high frequency circuit. Inductance in the power supply leads can form resonant circuits that produce peaking in the amplifier’s response. In addition, if large current transients must be delivered to the load, then bypass capacitors (typically greater than 1 µF) will be required to provide the best settling time and lowest distortion. A parallel combination of at least 4.7 µF, and between 0.1 µF and 0.01 µF, is recommended. Some brands of electrolytic capacitors will require a small series damping resistor ≈4.7 Ω for optimum results. Driving Capacitive Loads The AD8047/AD8048 have excellent cap load drive capability for high speed op amps as shown in Figures 55 and 57. However, when driving cap loads greater than 25 pF, the best frequency response is obtained by the addition of a small series resistance. It is worth noting that the frequency response of the –12– REV. 0 AD8047/AD8048 circuit when driving large capacitive loads will be dominated by the passive roll-off of RSERIES and CL. With a settling time of 30 ns to 0.01% and 13 ns to 0.1%, the devices are an excellent choice for DAC I/V conversion. The same characteristics along with low harmonic distortion make them a good choice for ADC buffering/amplification. With superb linearity at relatively high signal frequencies, the AD8047 and AD8048 are ideal drivers for ADCs up to 12 bits. RF RSERIES AD8047 RL 1kΩ (1000 V/µs) give higher performance capabilities to these applications over previous voltage feedback designs. CL Operation as a Video Line Driver The AD8047 and AD8048 have been designed to offer outstanding performance as video line drivers. The important specifications of differential gain (0.01%) and differential phase (0.02°) meet the most exacting HDTV demands for driving video loads. Figure 54. Driving Capacitive Loads 200Ω 200Ω 10µF +VS 0.1µF 7 2 500mV 3 VIN 5ns 75Ω CABLE 75Ω AD8047/ AD8048 75Ω CABLE 6 VOUT 0.1µF 4 75Ω 75Ω 10µF Figure 55. AD8047 Large Signal Transient Response; VO = 2 V p-p, G = +1, RF = 0 Ω, RSERIES = 0 Ω, CL = 27 pF RF Figure 58. Video Line Driver Active Filters RSERIES RIN –VS AD8048 RL 1kΩ CL Figure 56. Driving Capacitive Loads The wide bandwidth and low distortion of the AD8047 and AD8048 are ideal for the realization of higher bandwidth active filters. These characteristics, while being more common in many current feedback op amps, are offered in the AD8047 and AD8048 in a voltage feedback configuration. Many active filter configurations are not realizable with current feedback amplifiers. A multiple feedback active filter requires a voltage feedback amplifier and is more demanding of op amp performance than other active filter configurations such as the Sallen-Key. In general, the amplifier should have a bandwidth that is at least ten times the bandwidth of the filter if problems due to phase shift of the amplifier are to be avoided. Figure 59 is an example of a 20 MHz low pass multiple feedback active filter using an AD8048. VIN 500mV R1 154Ω +5V C1 50pF R4 154Ω R3 78.7Ω C2 100pF 0.1µF 1 7 2 5ns 10µF AD8048 100Ω 5 3 6 0.1µF 4 Figure 57. AD8048 Large Signal Transient Response; VO = 2 V p-p, G = +2, RF = RIN = 200 Ω, RSERIES = 0 Ω, CL = 27 pF 10µF –5V Figure 59. Active Filter Circuit APPLICATIONS The AD8047 and AD8048 are voltage feedback amplifiers well suited for such applications as photodetectors, active filters, and log amplifiers. The devices’ wide bandwidth (260 MHz), phase margin (65°), low noise current (1.0 pA/√Hz), and slew rate REV. 0 Choose: FO = Cutoff Frequency = 20 MHz α = Damping Ratio = 1/Q = 2 –13– VOUT AD8047/AD8048 –R4 R1 = 1 H = Absolute Value of Circuit Gain = The PCB should have a ground plane covering all unused portions of the component side of the board to provide a low impedance path. The ground plane should be removed from the area near the input pins to reduce stray capacitance. Then: k = 2 π FO C1 4 C1(H +1) α2 α R1 = 2 HK α R3 = 2 K (H +1) R4 = H(R1) Chip capacitors should be used for the supply bypassing (see Figure 60). One end should be connected to the ground plane and the other within 1/8 inch of each power pin. An additional large (0.47 µF–10 µF) tantalum electrolytic capacitor should be connected in parallel, though not necessarily so close, to supply current for fast, large signal changes at the output. C2 = The feedback resistor should be located close to the inverting input pin in order to keep the stray capacitance at this node to a minimum. Capacitance variations of less than 1 pF at the inverting input will significantly affect high speed performance. A/D Converter Driver As A/D converters move toward higher speeds with higher resolutions, there becomes a need for high performance drivers that will not degrade the analog signal to the converter. It is desirable from a system’s standpoint that the A/D be the element in the signal chain that ultimately limits overall distortion. This places new demands on the amplifiers used to drive fast, high resolution A/Ds. Stripline design techniques should be used for long signal traces (greater than about 1 inch). These should be designed with a characteristic impedance of 50 Ω or 75 Ω and be properly terminated at each end. Evaluation Board An evaluation board for both the AD8047 and AD8048 is available that has been carefully laid out and tested to demonstrate that the specified high speed performance of the device can be realized. For ordering information, please refer to the Ordering Guide. With high bandwidth, low distortion and fast settling time the AD8047 and AD8048 make high performance A/D drivers for advanced converters. Figure 60 is an example of an AD8047 used as an input driver for an AD872, a 12-bit, 10 MSPS A/D converter. The layout of the evaluation board can be used as shown or serve as a guide for a board layout. Layout Considerations The specified high speed performance of the AD8047 and AD8048 requires careful attention to board layout and component selection. Proper RF design techniques and low pass parasitic component selection are mandatory +5V DIGITAL +5V ANALOG 10Ω DV DD 4 DGND AV DD 0.1µF +5V ANALOG 5 DRV DD AGND DRGND 10µF CLK AD872 0.1µF 1 7 2 AD8047 ANALOG IN OTR 3 5 1 6 MSB BIT2 BIT3 BIT4 BIT5 BIT6 BIT7 BIT8 BIT9 BIT10 BIT11 BIT12 VINA 0.1µF 4 2 VINB 27 –5V ANALOG 10µF REF GND 0.1µF 28 REF IN 26 1µF AGND REF OUT AV SS 7 6 0.1µF +5V DIGITAL 22 23 0.1µF CLOCK INPUT 21 20 19 18 17 16 15 14 13 12 11 10 9 8 49.9Ω DIGITAL OUTPUT 24 AV SS 3 25 0.1µF 0.1µF –5V ANALOG Figure 60. AD8047 Used as Driver for an AD872, a 12-Bit, 10 MSPS A/D Converter –14– REV. 0 AD8047/AD8048 RF +VS +V S RG RO OPTIONAL OUT IN RT –VS C1 1000pF C3 0.1µF C5 10µF C2 1000pF C4 0.1µF C6 10µF –V S Supply Bypassing Noninverting Configuration Figure 61. Noninverting Configurations for Evaluation Boards Table I. AD8047 +2 Component –1 +1 RF RG RO RS RT Small Signal BW (–3 dB) 200 Ω 200 Ω 49.9 Ω – 66.5 Ω 66.5 Ω – 49.9 Ω 0Ω 49.9 Ω 90 MHz 260 MHz 95 MHz 1 kΩ 1 kΩ 49.9 Ω 0Ω 49.9 Ω AD8048 +10 +10 +101 –1 +2 1 kΩ 110 Ω 49.9 Ω 0Ω 49.9 Ω 1 kΩ 10 Ω 49.9 Ω 0Ω 49.9 Ω 200 Ω 200 Ω 49.9 Ω – 66.5 Ω 200 Ω 200 Ω 49.9 Ω 0Ω 49.9 Ω 10 MHz 1 MHz 250 MHz 250 MHz 22 MHz 1 kΩ 110 Ω 49.9 Ω 0Ω 49.9 Ω +101 1 kΩ 10 Ω 49.9 Ω 0Ω 49.9 Ω 2 MHz SOIC (R) NONINVERTER SOIC (R) INVERTER Figure 62. Evaluation Board Silkscreen (Top) SOIC (R) INVERTER SOIC (R) NONINVERTER Figure 63. Board Layout (Solder Side) REV. 0 –15– C1995–10–1/95 AD8047/AD8048 SOIC (R) NONINVERTER SOIC (R) INVERTER Figure 64. Board Layout (Component Side) OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 8-Pin Plastic DIP (N Package) 8 5 0.280 (7.11) 0.240 (6.10) PIN 1 1 4 0.325 (8.25) 0.300 (7.62) 0.430 (10.92) 0.348 (8.84) 0.060 (1.52) 0.015 (0.38) 0.210 (5.33) MAX 0.195 (4.95) 0.115 (2.93) 0.130 (3.30) MIN 0.160 (4.06) 0.115 (2.93) 0.022 (0.558) 0.014 (0.356) 0.100 (2.54) BSC 0.070 (1.77) 0.045 (1.15) 0.015 (0.381) 0.008 (0.204) SEATING PLANE 8-Pin Plastic SOIC (R Package) 0.150 (3.81) 8 5 0.244 (6.20) 0.228 (5.79) 1 PRINTED IN U.S.A. PIN 1 0.157 (3.99) 0.150 (3.81) 4 0.197 (5.01) 0.189 (4.80) 0.102 (2.59) 0.094 (2.39) 0.010 (0.25) 0.004 (0.10) 0.050 (1.27) BSC 0.019 (0.48) 0.014 (0.36) 0.020 (0.051) x 45 ° CHAMF 0.190 (4.82) 0.170 (4.32) 8° 0° 0.090 (2.29) 10 ° 0° 0.098 (0.2482) 0.075 (0.1905) –16– 0.030 (0.76) 0.018 (0.46) REV. 0