AD 5962-9559701MPA

FEATURES
Superb Clamping Characteristics
3 mV Clamp Error
1.5 ns Overdrive Recovery
Minimized Nonlinear Clamping Region
240 MHz Clamp Input Bandwidth
ⴞ3.9 V Clamp Input Range
Wide Bandwidth
AD8036
AD8037
Small Signal
240 MHz 270 MHz
Large Signal (4 V p-p) 195 MHz 190 MHz
Good DC Characteristics
2 mV Offset
10 ␮V/ⴗC Drift
Ultralow Distortion, Low Noise
–72 dBc typ @ 20 MHz
4.5 nV/√Hz Input Voltage Noise
High Speed
Slew Rate 1500 V/␮s
Settling 10 ns to 0.1%, 16 ns to 0.01%
ⴞ3 V to ⴞ5 V Supply Operation
APPLICATIONS
ADC Buffer
IF/RF Signal Processing
High Quality Imaging
Broadcast Video Systems
Video Amplifier
Full Wave Rectifier
PRODUCT DESCRIPTION
The AD8036 and AD8037 are wide bandwidth, low distortion
clamping amplifiers. The AD8036 is unity gain stable. The
AD8037 is stable at a gain of two or greater. These devices allow the designer to specify a high (VCH) and low (VCL ) output
clamp voltage. The output signal will clamp at these specified
levels. Utilizing a unique patent pending CLAMPIN™ input
clamp architecture, the AD8036 and AD8037 offer a 10× improvement in clamp performance compared to traditional output clamping devices. In particular, clamp error is typically
3 mV or less and distortion in the clamp region is minimized.
This product can be used as a classical op amp or a clamp amplifier where a high and low output voltage are specified.
The AD8036 and AD8037, which utilize a voltage feedback architecture, meet the requirements of many applications which
previously depended on current feedback amplifiers. The
AD8036 and AD8037 exhibit an exceptionally fast and accurate
pulse response (16 ns to 0.01%), extremely wide small-signal
FUNCTIONAL BLOCK DIAGRAM
8-Lead Plastic DIP (N), Cerdip (Q),
and SO Packages
NC
1
–INPUT
AD8036/
AD8037
8
VH
2
7
+VS
+INPUT
3
6
OUTPUT
–VS
4
5
VL
(Top View)
NC = NO CONNECT
and large-signal bandwidths and ultralow distortion. The
AD8036 achieves –66 dBc at 20 MHz, and 240 MHz smallsignal and 195 MHz large-signal bandwidths. The AD8036 and
AD8037’s recover from 2× clamp overdrive within 1.5 ns.
These characteristics position the AD8036/AD8037 ideally for
driving as well as buffering flash and high resolution ADCs.
In addition to traditional output clamp amplifier applications,
the input clamp architecture supports the clamp levels as additional inputs to the amplifier. As such, in addition to static dc
clamp levels, signals with speeds up to 240 MHz can be applied
to the clamp pins. The clamp values can also be set to any
value within the output voltage range provided that VH is greater
that VL . Due to these clamp characteristics, the AD8036 and
AD8037 can be used in nontraditional applications such as a
full-wave rectifier, a pulse generator, or an amplitude modulator. These novel applications are only examples of some of the
diverse applications which can be designed with input clamps.
The AD8036 is offered in chips, industrial (–40°C to +85°C)
and military (–55°C to +125°C) package temperature ranges
and the AD8037 in industrial. Industrial versions are available
in plastic DIP and SOIC; MIL versions are packaged in cerdip.
4
AD8036
VH = 3V
3
OUTPUT VOLTAGE – Volts
a
Low Distortion, Wide Bandwidth
Voltage Feedback Clamp Amps
AD8036/AD8037
VH = 2V
2
VH = 1V
1
0
VL = –1V
–1
–2
VL = –2V
VL = –3V
–3
CLAMPIN is a trademark of Analog Devices, Inc.
–4
–4
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
–3
–2
–1
0
1
INPUT VOLTAGE – Volts
2
3
4
Figure 1. Clamp DC Accuracy vs. Input Voltage
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 1999
AD8036/AD8037–SPECIFICATIONS
(±V = ±5 V; R = 100 Ω; A = +1 (AD8036); A = +2 (AD8037), V , V open, unless
S
LOAD
ELECTRICAL CHARACTERISTICS otherwise noted)
Parameter
DYNAMIC PERFORMANCE
Bandwidth (–3 dB)
Small Signal
Large Signal 1
Bandwidth for 0.1 dB Flatness
Slew Rate, Average +/–
Rise/Fall Time
Settling Time
To 0.1%
To 0.01%
HARMONIC/NOISE PERFORMANCE
2nd Harmonic Distortion
3rd Harmonic Distortion
3rd Order Intercept
Noise Figure
Input Voltage Noise
Input Current Noise
Average Equivalent Integrated
Input Noise Voltage
Differential Gain Error (3.58 MHz)
Differential Phase Error (3.58 MHz)
Phase Nonlinearity
CLAMP PERFORMANCE
Clamp Voltage Range 2
Clamp Accuracy
Clamp Nonlinearity Range3
Clamp Input Bias Current (VH or VL)
Clamp Input Bandwidth (–3 dB)
Clamp Overshoot
Overdrive Recovery
DC PERFORMANCE 4, RL = 150 Ω
Input Offset Voltage 5
V
V
AD8036A
Min Typ Max
Conditions
AD8037A
Min Typ Max
Units
MHz
MHz
240
195
200
160
130
1200
1.4
2.6
130
1100 1500
1.2
2.2
VOUT = 2 V Step
VOUT = 2 V Step
10
16
2 V p-p; 20 MHz, RL = 100 Ω
RL = 500 Ω
2 V p-p; 20 MHz, RL = 100 Ω
RL = 500 Ω
25 MHz
RS = 50 Ω
1 MHz to 200 MHz
1 MHz to 200 MHz
–59
–66
–68
–72
+46
18
6.7
2.2
0.1 MHz to 200 MHz
RL = 150 Ω
RL = 150 Ω
DC to 100 MHz
95
0.05
0.02
1.1
VCH or V CL
2× Overdrive, V CH = +2 V, VCL = –2 V
TMIN–TMAX
8036, VH, L = ±1 V; 8037, VH, L = ± 0.5 V
TMIN–TMAX
VCH or V CL = 2 V p-p
2× Overdrive, V CH or V CL = 2 V p-p
2× Overdrive
± 3.3
± 3.9
±3
100
± 40
150
240
1
1.5
2
± 10
4
Offset Voltage Drift
Input Bias Current
TMIN –TMAX
Input Offset Current
0.3
TMIN –TMAX
VCM = ± 2 V
VOUT = ±2.5 V
TMIN –TMAX
66
48
40
INPUT CHARACTERISTICS
Input Resistance
Input Capacitance
Input Common-Mode Voltage Range
OUTPUT CHARACTERISTICS
Output Voltage Range, R L = 150 Ω
Output Current
Output Resistance
Short Circuit Current
POWER SUPPLY
Operating Range
Quiescent Current
Power Supply Rejection Ratio
L
VOUT ≤ 0.4 V p-p
150
8036, VOUT = 2.5 V p-p; 8037, VOUT = 3.5 V p-p 160
VOUT ≤ 0.4 V p-p
8036, RF = 140 Ω; 8037, R F = 274 Ω
VOUT = 4 V Step, 10–90%
900
VOUT = 0.5 V Step, 10–90%
VOUT = 4 V Step, 10–90%
TMIN –TMAX
Common-Mode Rejection Ratio
Open-Loop Gain
H
TMIN –TMAX
TMIN –TMAX
270
190
MHz
V/µs
ns
ns
10
16
–52
–59
–61
–65
–52
–72
–70
–80
+41
14
4.5
2.1
60
0.02
0.02
1.1
0.09
0.04
± 10
± 20
± 60
± 80
5
–45
–65
–63
–73
0.04
0.04
± 3.3 ± 3.9
±3
± 10
± 20
100
± 50 ± 70
± 90
180 270
1
5
1.3
7
11
2
± 10
3
10
15
3
5
90
55
ns
ns
0.1
70
54
46
7
10
9
15
3
5
90
60
dBc
dBc
dBc
dBc
dBm
dB
nV√Hz
pA√Hz
µV rms
%
Degree
Degree
V
mV
mV
mV
µA
µA
MHz
%
ns
mV
mV
µV/°C
µA
µA
µA
µA
dB
dB
dB
500
1.2
± 2.5
500
1.2
± 2.5
kΩ
pF
V
± 3.2
± 3.9
70
0.3
240
± 3.2 ± 3.9
70
0.3
240
V
mA
Ω
mA
± 3.0
± 5.0
20.5
50
60
± 3.0 ± 5.0 ± 6.0
18.5 19.5
24
56
66
V
mA
mA
dB
± 6.0
21.5
25
NOTES
1
See Max Ratings and Theory of Operation sections of data sheet.
2
See Max Ratings.
3
Nonlinearity is defined as the voltage delta between the set input clamp voltage (VH or V L) and the voltage at which V OUT starts deviating from VIN (see Figure 73).
4
Measured at A V = 50.
5
Measured with respect to the inverting input.
Specific ations subject to change without notice.
–2–
REV. A
AD8036/AD8037
ABSOLUTE MAXIMUM RATINGS 1
MAXIMUM POWER DISSIPATION
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.6 V
Voltage Swing × Bandwidth Product . . . . . . . . . . . 350 V-MHz
|VH–VIN| . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .≤ 6.3 V
|VL–VIN| . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .≤ 6.3 V
Internal Power Dissipation2
Plastic DIP Package (N) . . . . . . . . . . . . . . . . . . . . 1.3 Watts
Small Outline Package (SO) . . . . . . . . . . . . . . . . . . 0.9 Watts
Input Voltage (Common Mode) . . . . . . . . . . . . . . . . . . . . ± VS
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . ± 1.2 V
Output Short Circuit Duration
. . . . . . . . . . . . . . . . . . . . . . Observe Power Derating Curves
Storage Temperature Range N, R . . . . . . . . . –65°C to +125°C
Operating Temperature Range (A Grade) . . . –40°C to +85°C
Lead Temperature Range (Soldering 10 sec) . . . . . . . . +300°C
The maximum power that can be safely dissipated by these devices is limited by the associated rise in junction temperature.
The maximum safe junction temperature for plastic encapsulated devices is determined by the glass transition temperature
of the plastic, approximately +150°C. Exceeding this limit temporarily may cause a shift in parametric performance due to a
change in the stresses exerted on the die by the package. Exceeding a junction temperature of +175°C for an extended period can
result in device failure.
While the AD8036 and AD8037 are internally short circuit protected, this may not be sufficient to guarantee that the maximum junction temperature (+150°C) is not exceeded under all
conditions. To ensure proper operation, it is necessary to observe the maximum power derating curves.
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2
Specification is for device in free air:
8-Lead Plastic DIP: θ JA = 90°C/W
8-Lead SOIC: θ JA = 155°C/W
8-Lead Cerdip: θ JA = 110°C/W.
MAXIMUM POWER DISSIPATION – Watts
2.0
METALIZATION PHOTO
Dimensions shown in inches and (mm).
Connect Substrate to –VS .
–IN
VH
2
8
+VS
7
8-LEAD PLASTIC DIP
PACKAGE
TJ = +1508C
1.5
1.0
8-LEAD SOIC
PACKAGE
0.5
0
–50 –40 –30 –20 –10 0 10 20 30 40 50 60
AMBIENT TEMPERATURE – 8C
0.046
(1.17)
6
70
80 90
Figure 2. Plot of Maximum Power Dissipation vs.
Temperature
OUT
ORDERING GUIDE
3
+IN
4
–VS
5
8036
VL
Model
AD8036
0.050 (1.27)
–IN
VH
+VS
2
8
7
0.046
(1.17)
6
3
+IN
4
–VS
5
VL
0.050 (1.27)
OUT
Temperature
Range
Package
Option
AD8036AN
AD8036AR
AD8036AR-REEL
AD8036AR-REEL7
AD8036ACHIPS
AD8036-EB
5962-9559701MPA
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
Plastic DIP
SOIC
13" Tape and Reel
7" Tape and Reel
Die
Evaluation Board
–55°C to +125°C Cerdip
N-8
SO-8
SO-8
SO-8
AD8037AN
AD8037AR
AD8037AR-REEL
AD8037AR-REEL7
AD8037ACHIPS
AD8037-EB
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
N-8
SO-8
SO-8
SO-8
Plastic DIP
SOIC
13" Tape and Reel
7" Tape and Reel
Die
Evaluation Board
Q-8
8037
AD8037
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although these devices feature proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
REV. A
Package
Description
–3–
WARNING!
ESD SENSITIVE DEVICE
AD8036/AD8037
AD8036–Typical Characteristics
RF
RF
10mF
10mF
+VS
PULSE
GENERATOR
+VH
PULSE
GENERATOR
0.1mF
+VS
0.1mF
0.1mF
T R /T F = 350ps
T R /T F = 350ps
130V
AD8036
VIN
VOUT
0.1mF
49.9V
AD8036
130V
VIN
RL = 100V
49.9V
10mF
RL = 100V
10mF
0.1mF
–VS
VOUT
0.1mF
VL
–VS
Figure 6. Noninverting Clamp Configuration, G = +1
Figure 3. Noninverting Configuration, G = +1
Figure 4. Large Signal Transient Response; VO = 4 V p-p,
G = +1, RF = 140 Ω
Figure 7. Clamped Large Signal Transient Response (2 ×
Overdrive); VO = 2 V p-p, G = +1, R F = 140 Ω, V H = +1 V,
VL = –1 V
Figure 5. Small Signal Transient Response; VO = 400 mV
p-p, G = +1, RF = 140 Ω
Figure 8. Clamped Small Signal Transient Response
(2 × Overdrive); VO = 400 mV p-p, G = +1, RF = 140 Ω,
VH = +0.2 V, VL = –0.2 V
–4–
REV. A
AD8036/AD8037
AD8037–Typical Characteristics
RF
RF
PULSE
GENERATOR
10mF
+VS
T R /T F = 350ps
PULSE
GENERATOR
T R /T F = 350ps
0.1mF
AD8037
VIN
VOUT
0.1mF
49.9V
0.1mF
0.1mF
AD8037
100V
VIN
RL = 100V
VOUT
0.1mF
49.9V
10mF
RL = 100V
10mF
0.1mF
VL
–VS
–VS
Figure 12. Noninverting Clamp Configuration, G = +2
Figure 9. Noninverting Configuration, G = +2
Figure 10. Large Signal Transient Response; VO = 4 V p-p,
G = +2, RF = RIN = 274 Ω
Figure 13. Clamped Large Signal Transient Response
(2 × Overdrive); VO = 2 V p-p, G = +2, RF = RIN = 274 Ω,
VH = +0.5 V, VL = –0.5 V
Figure 14. Clamped Small Signal Transient Response
(2 × Overdrive); VO = 400 mV p-p, G = +2, RF = RIN = 274 Ω,
VH = +0.1 V, VL = –0.1 V
Figure 11. Small Signal Transient Response;
VO = 400 mV p-p, G = +2, RF = RIN = 274 Ω
REV. A
+VS
RIN
RIN
100V
10mF
+VH
–5–
AD8036/AD8037
AD8036–Typical Characteristics
400
2
140V
GAIN – dB
–2
VO = 300mV p-p
VS = 65V
RL = 100V
–3dB BANDWIDTH – MHz
0
–1
RF
200V
1
102V
49.9V
–3
–4
–5
VS = 65V
RL = 100V
GAIN = +1
350
130V
AD8036
RL
49.9V
N PACKAGE
300
R PACKAGE
250
–6
200
–7
–8
1M
10M
100M
FREQUENCY – Hz
20
1G
Figure 15. AD8036 Small Signal Frequency Response,
G = +1
0
VO = 300mV p-p
VS = 65V
RL = 100V
–1
140V
130V
–0.4
–2
–5
–6
–0.7
–7
10M
100M
FREQUENCY – Hz
90
100
2
80
80
1
60
50
20
40
0
GAIN
–2
–20
20
–40
10
–60
0
–80
–6
–100
–7
100k
1M
10M
FREQUENCY – Hz
100M
VS = 65V
VO = 300mV p-p
RL = 100V
140V
–3
30
–10
1G
0
–1
GAIN – dB
40
PHASE MARGIN – Degrees
PHASE
10M
100M
FREQUENCY – Hz
Figure 19. AD8036 Large Signal Frequency Response,
G = +1
Figure 16. AD8036 0.1 dB Flatness, N Package (for R
Package Add 20 Ω to RF)
70
50V
RF = 50V
TO
250V
BY
50V
–8
1M
1G
60
VS = 65V
VO = 2.5V p-p
RL = 100V
–4
–0.6
–0.8
1M
250V
–3
–0.5
OPEN -LOOP GAIN – dB
240
0
OUTPUT – dB
GAIN – dB
1
150V
–0.1
–20
10k
220
2
158V
0.1
–0.3
60
80 100 120 140 160 180 200
VALUE OF FEEDBACK RESISTOR (RF) – V
Figure 18. AD8036 Small Signal –3 dB Bandwidth vs. RF
0.2
–0.2
40
–4
–120
1G
–8
100k
(VO)
AD8036
–5
1V
100V
VH
VL (VIN)
1M
10M
FREQUENCY – Hz
100M
1G
Figure 20. AD8036 Clamp Input Bandwidth, VH, VL
Figure 17. AD8036 Open-Loop Gain and Phase Margin vs.
Frequency, RL = 100 Ω
–6–
REV. A
AD8036/AD8037
DIFF GAIN – %
–50
0.06
VO = 2V p-p
VS = 65V
RL = 500V
G = +1
–70
0.04
0.02
0.00
–0.02
–0.04
–0.06
1st
2nd
3rd
4th
5th
6th
7th
8th
9th 10th 11th
1st
2nd
3rd
4th
5th
6th
7th
8th
9th 10th 11th
2ND HARMONIC
DIFF PHASE – Degrees
HARMONIC DISTORTION – dBc
–30
–90
3RD HARMONIC
–110
–130
10k
100k
1M
FREQUENCY – Hz
10M
100M
0.04
0.02
0.00
–0.02
–0.04
Figure 24. AD8036 Differential Gain and Phase Error,
G = +1, RL = 150 Ω, F = 3.58 MHz
Figure 21. AD8036 Harmonic Distortion vs. Frequency,
RL = 500 Ω
–50
VO = 2V p-p
VS = 65V
RL = 100V
G = +1
0.05
0.04
0.03
0.02
2ND HARMONIC
–70
ERROR – %
HARMONIC DISTORTION – dBc
–30
–90
3RD HARMONIC
0.01
0
–0.01
–0.02
–0.03
–110
–0.04
–0.05
–130
10k
100k
1M
FREQUENCY – Hz
10M
0
100M
Figure 22. AD8036 Harmonic Distortion vs. Frequency,
RL = 100 Ω
5
10
15 20 25 30
SETTLING TIME – ns
35
40
45
Figure 25. AD8036 Short-Term Settling Time to 0.01%, 2 V
Step, G = +1, RL = 100 Ω
60
0.4
0.3
0.2
0.1
ERROR – %
INTERCEPT – +dBm
50
40
0
–0.1
–0.2
–0.3
–0.4
30
–0.5
–0.6
20
10
0
20
40
FREQUENCY – MHz
60
80
100
Figure 23. AD8036 Third Order Intercept vs. Frequency
REV. A
2
4
6
8
10 12 14
SETTLING TIME - ms
16
18
Figure 26. AD8036 Long-Term Settling Time, 2 V Step,
G = +1, RL = 100 Ω
–7–
AD8036/AD8037
AD8037–Typical Characteristics
8
475
7
VS = 65V
RL = 100V
GAIN = +2
350
374
GAIN – dB
5
4
VO = 300mV p-p
VS = 65V
RL = 100V
–3dB BANDWIDTH – MHz
6
274
174
3
2
1
RIN
100V
RF
AD8037
RL
300
49.9V
250
R PACKAGE
N PACKAGE
200
0
–1
150
–2
1M
10M
100M
FREQUENCY – Hz
1G
100
Figure 27. AD8037 Small Signal Frequency Response,
G = +2
6
274
VO = 3.00mV p-p
VS = 65V
RL = 100V
5
249
4
GAIN – dB
GAIN – dB
550
RF = 475V
7
224
–0.3
–0.4
VO = 3.5 V p-p
VS = 65V
RL = 100V
RF = 75V
3
RF = 75V
TO
475V
BY
100V
2
–0.5
1
–0.6
0
–0.7
–1
–0.8
1M
10M
100M
FREQUENCY – Hz
–2
1M
1G
Figure 28. AD8037 0.1 dB Flatness, N Package
(for R Package Add 20 Ω to RF)
10M
100M
FREQUENCY – Hz
1G
Figure 31. AD8037 Large Signal Frequency Response,
G = +2
65
60
8
55
50
7
100
PHASE
6
50
35
0
30
25
20
–50
GAIN
15
10
–100
5
0
–150
–5
–10
–200
100k
1M
10M
FREQUENCY – Hz
100M
5
GAIN – dB
45
40
PHASE MARGIN – Degrees
OPEN -LOOP GAIN – dB
500
8
0
–15
10k
250 300 350 400 450
VALUE OF RF,RIN – V
301
0.1
–0.2
200
Figure 30. AD8037 Small Signal –3 dB Bandwidth
vs. RF, RIN
0.2
–0.1
150
4
VS = 65V
VO = 300mV p-p
RL = 100V
274V
3
2
274V
0
1V
–2
100k
Figure 29. AD8037 Open-Loop Gain and Phase Margin
vs. Frequency, RL = 100 Ω
100V
VH
VL (VIN)
–1
–250
1G
(VO)
AD8037
1
1M
10M
FREQUENCY – Hz
100M
1G
Figure 32. AD8037 Clamp Input Bandwidth, VH, VL
–8–
REV. A
AD8036/AD8037
0.03
DIFF GAIN – %
–50
VO = 2V p-p
VS = 65V
RL = 500V
G = +2
–70
0.02
0.01
0.00
–0.01
–0.02
–0.03
2ND HARMONIC
1st
DIFF PHASE – Degrees
HARMONIC DISTORTION – dBc
–30
–90
3RD HARMONIC
–110
–130
10k
100k
1M
FREQUENCY – Hz
3rd
4th
5th
6th
7th
8th
9th 10th 11th
2nd
3rd
4th
5th
6th
7th
8th
9th 10th 11th
0.03
0.02
0.01
0.00
–0.01
–0.02
–0.03
1st
100M
10M
2nd
Figure 36. AD8037 Differential Gain and Phase Error
G = +2, RL = 150 Ω, F = 3.58 MHz
Figure 33. AD8037 Harmonic Distortion vs. Frequency,
R L = 500 Ω
–30
–50
–0.04
–0.03
2ND HARMONIC
–0.02
ERROR – %
HARMONIC DISTORTION – dBc
–0.05
VO = 2V p-p
VS = 65V
RL = 100V
G = +2
–70
–90
3RD HARMONIC
–0.01
0
–0.01
–0.02
–0.03
–110
–0.04
–130
10k
–0.05
100k
1M
FREQUENCY – Hz
100M
10M
0
5
10 15 20 25 30
SETTLING TIME – ns
35
40
45
Figure 37. AD8037 Short-Term Settling Time to 0.01%,
2 V Step, G = +2, RL = 100 Ω
Figure 34. AD8037 Harmonic Distortion vs. Frequency,
RL = 100 Ω
60
0.4
0.3
0.2
0.1
ERROR – %
INTERCEPT – +dBm
50
40
0
–0.1
–0.2
–0.3
30
–0.4
–0.5
–0.6
20
10
20
40
FREQUENCY – MHz
60
80
0
100
4
6
8 10 12 14
SETTLING TIME – ms
16
18
Figure 38. AD8037 Long-Term Settling Time 2 V Step,
RL = 100 Ω
Figure 35. AD8037 Third Order Intercept vs. Frequency
REV. A
2
–9–
AD8036/AD8037–Typical Characteristics
17
28
15
INPUT NOISE VOLTAGE – nV/ Hz
INPUT NOISE VOLTAGE – nV/ Hz
32
VS = 65V
24
20
16
12
VS = 65V
13
11
9
7
5
8
4
10
100
1k
FREQUENCY – Hz
10k
3
10
100k
+PSRR
PSRR – dB
PSRR – dB
–PSRR
40
35
30
25
20
15
10
5
0
10k
100k
1M
10M
FREQUENCY – Hz
100M
1G
80
75
70
65
60
55
50
45
40
35
30
25
20
15
10
5
0
10k
10k
100k
–PSRR
+PSRR
100k
1M
10M
FREQUENCY – Hz
100M
1G
Figure 43. AD8037 PSRR vs. Frequency
Figure 40. AD8036 PSRR vs. Frequency
100
100
VS = 65V
DVCM = 1V
RL = 100V
90
VS = 65V
DVCM = 1V
RL = 100V
90
80
80
70
CMRR – dB
CMRR – dB
1k
FREQUENCY – Hz
Figure 42. AD8037 Noise vs. Frequency
Figure 39. AD8036 Noise vs. Frequency
80
75
70
65
60
55
50
45
100
60
50
70
60
50
40
40
30
30
20
100k
1M
10M
FREQUENCY – Hz
100M
20
100k
1G
1M
10M
FREQUENCY – Hz
100M
1G
Figure 44. AD8037 CMRR vs. Frequency
Figure 41. AD8036 CMRR vs. Frequency
–10–
REV. A
AD8036/AD8037
1k
1400
1300
VS = 65V
G = +1
1200
OPEN -LOOP GAIN – V/ V
100
ROUT – V
10
1
0.1
1100
AD8037
1000
+AOL
900
–AOL
800
700
600
500
+AOL
AD8036
–AOL
0.01
0.1M
1.0M
10M
FREQUENCY – Hz
100M
400
–60
300M
–40
–20
0
20
40
60
80
100
120
140
JUNCTION TEMPERATURE – 8C
Figure 48. Open-Loop Gain vs. Temperature
Figure 45. AD8036 Output Resistance vs. Frequency
1k
74
VS = 65V
G = +2
100
–PSRR
72
AD8037
70
+PSRR
PSRR – dB
ROUT – V
10
1
68
AD8037
66
64
–PSRR
AD8036
+PSRR
0.1
62
AD8036
0.01
0.1M
1.0M
10M
FREQUENCY – Hz
100M
60
–60
300M
Figure 46. AD8037 Output Resistance vs. Frequency
–40
–20
0
20
40
60
80 100
JUNCTION TEMPERATURE – 8C
120
140
Figure 49. PSRR vs. Temperature
96
4.2
DVCM = 2V
4.1
+VOUT
94
4.0
–VOUT
3.9
CMRR – dB
OUTPUT SWING – Volts
95
RL=150
3.8
3.7
93
92
91
90
3.6
+VOUT
89
3.5
RL= 50
–VOUT
3.4
–60
–40
–20
0
20
40
60
80
100
JUNCTION TEMPERATURE – 8C
120
88
15
140
Figure 47. AD8036/AD8037 Output Swing vs. Temperature
REV. A
–11–
25
35
45
55
65
75
JUNCTION TEMPERATURE – 8C
85
95
Figure 50. AD8036/AD8037 CMRR vs. Temperature
AD8036/AD8037–Typical Characteristics
270
24
SHORT CIRCUIT CURRENT – mA
23
SUPPLY CURRENT – mA
AD8036, VS = 66V
22
AD8037, VS = 66V
21
AD8036, VS = 65V
20
AD8037, VS = 65V
19
260
AD8036
250
AD8037
AD8037
SINK
240
AD8036
230
SOURCE
220
210
18
17
–60
–40
–20
0
20
40
60
80 100
JUNCTION TEMPERATURE – 8C
120
200
–60
140
–40
–20
0
20
40
60
80 100
JUNCTION TEMPERATURE – 8C
120
140
Figure 54. Short Circuit Current vs. Temperature
Figure 51. Supply Current vs. Temperature
–2.50
4.5
VS = 66V
–IB
4.0
INPUT BIAS CURRENT – mA
INPUT OFFSET VOLTAGE – mV
–2.25
–2.00
VS = 66V
AD8037
–1.75
–1.50
VS = 65V
VS = 65V
–1.25
AD8036
–1.00
–40
–20
0
20
40
60
80 100
JUNCTION TEMPERATURE – 8C
120
+IB
2.5
–40
–20
0
20
40
60
80
100
JUNCTION TEMPERATURE – 8C
120
140
48
44
3 WAFER LOTS
COUNT = 632
3 WAFER LOTS
COUNT = 853
40
36
36
32
FREQ. DIST
32
24
COUNT
28
FREQ. DIST
20
16
28
24
20
16
12
12
8
8
4
4
0
–6
AD8037
Figure 55. Input Bias Current vs. Temperature
44
COUNT
–IB
3.0
1.5
–60
140
Figure 52. Input Offset Voltage vs. Temperature
40
+IB
3.5
2.0
–0.75
–0.50
–60
AD8036
–5
–4
–3
–2
–1
0
1
INPUT OFFSET VOLTAGE – mV
2
3
0
–4.5
4
Figure 53. AD8036 Input Offset Voltage Distribution
–4.0
–3.5
–3.0 –2.5 –2.0 –1.5 –1.0 –0.5
INPUT OFFSET VOLTAGE – mV
0
0.5
Figure 56. AD8037 Input Offset Voltage Distribution
–12–
REV. A
Clamp Characteristics–AD8036/AD8037
20
–80
VCL =
–3V
10
VCL =
–2V
VCL =
–1V
–75
AD8036, ACL = +1
AD8037, ACL = +2
HARMONIC DISTORTION – dBc
INPUT ERROR VOLTAGE – mV
15
5
0
AD8036
–5
AD8037
–10
VCH =
+1V
–15
VCH =
+2V
VCH =
+3V
–70
AD8037 3RD
HARMONIC
–65
–60
AD8037 2ND
HARMONIC
–55
–50
AD8036 2ND
HARMONIC
–45
AD8036 AD8037
–40
VH
VL
G
–35
–20
–3
–2
–1
0
1
OUTPUT VOLTAGE – Volts
2
–30
0.6
3
20
+0.5V
–0.5V
+2V
0.65
0.7
0.75
0.8
0.85
0.9
0.95
ABSOLUTE VALUE OF OUTPUT VOLTAGE – Volts
1.0
80
CLAMP INPUT BIAS CURRENT – mA
VH = + 1V
VL = – 1V
15
10
NONLINEARITY – mV
+1V
–1V
+1V
Figure 60. Harmonic Distortion as Output Approaches
Clamp Voltage; VO = 2 V p-p, RL = 100 ⍀, f = 20 MHz
Figure 57. Input Error Voltage vs. Clamped Output
Voltage
5
0
–5
–10
–15
60
POSITIVE IBH, IBL DENOTES
CURRENT FLOW INTO
CLAMP INPUTS VH, VL
40
20
IBL
0
IBH
–20
–40
–60
–20
–1.0
–0.8
–0.6
–0.4 –0.2 0.0
0.2
0.4
INPUT VOLTAGE AV – Volts
0.6
0.8
–80
–5
1.0
Figure 58. AD8036/AD8037 Nonlinearity Near Clamp
Voltage
–4
–3
–2
–1
0
1
2
3
INPUT CLAMP VOLTAGE (VH ,VL) – Volts
4
5
Figure 61. AD8036/AD8037 Clamp Input Bias Current vs.
Input Clamp Voltage
+2V
+2V
+1V
+1V
0V
0V
REF
REF
Figure 59. AD8036 Clamp Overdrive (2X) Recovery
REV. A
AD8036 3RD
HARMONIC
Figure 62. AD8037 Clamp Overdrive (2X) Recovery
–13–
0.5
0.5
0.4
0.4
0.3
0.3
0.2
0.2
ERROR – %
ERROR – %
AD8036/AD8037–Clamp Characteristics
0.1
0
–0.1
–0.2
–0.3
–0.3
–0.4
–0.4
–0.5
0
10
20 30 40 50 60
SETTLING TIME – ns
70
80
90
0
Figure 63. AD8036 Clamp Settling (0.1%), V H = +1 V,
VL = –1 V, 2 × Overdrive
10
20 30 40 50 60
SETTLING TIME – ns
70
80
90
Figure 66. AD8037 Clamp Settling (0.1%), VH = +0.5 V,
VL = –0.5 V, 2 × Overdrive
0.5
0.5
0.4
0.4
0.3
0.3
0.2
0.2
ERROR – %
ERROR – %
0
–0.1
–0.2
–0.5
0.1
0
–0.1
0.1
0
–0.1
–0.2
–0.2
–0.3
–0.3
–0.4
–0.4
–0.5
–0.5
0
5 10 15 20 25
SETTLING TIME – ns
30
35
0
40
Figure 64. AD8036 Clamp Recovery Settling Time (High),
from +2 × Overdrive to 0 V
5 10 15 20 25
SETTLING TIME – ns
30
35
40
Figure 67. AD8037 Clamp Recovery Settling Time (High),
from +2 × Overdrive to 0 V
0.5
0.5
0.4
0.4
0.3
0.3
0.2
0.2
ERROR – %
ERROR – %
0.1
0.1
0
–0.1
0.1
0
–0.1
–0.2
–0.2
–0.3
–0.3
–0.4
–0.4
–0.5
–0.5
0
5
10 15 20 25
SETTLING TIME – ns
30
35
40
Figure 65. AD8036 Clamp Recovery Settling Time (Low),
from –2 × Overdrive to 0 V
0
5 10 15 20 25
SETTLING TIME – ns
30 35
40
Figure 68. AD8037 Clamp Recovery Settling Time (Low),
from –2 × Overdrive to 0 V
–14–
REV. A
AD8036/AD8037
THEORY OF OPERATION
General
The AD8036 and AD8037 are wide bandwidth, voltage feedback clamp amplifiers. Since their open-loop frequency response follows the conventional 6 dB/octave roll-off, their gain
bandwidth product is basically constant. Increasing their
closed-loop gain results in a corresponding decrease in small signal bandwidth. This can be observed by noting the bandwidth
specification, between the AD8036 (gain of 1) and AD8037
(gain of 2). The AD8036/AD8037 typically maintain 65 degrees of phase margin. This high margin minimizes the effects
of signal and noise peaking.
While the AD8036 and AD8037 can be used in either an inverting or noninverting configuration, the clamp function will only
work in the noninverting mode. As such, this section shows connections only in the noninverting configuration. Applications
that require an inverting configuration will be discussed in the
Applications section. In applications that do not require clamping, Pins 5 and 8 (respectively VL and VH) may be left floating.
See Input Clamp Amp Operation and Applications sections
otherwise.
Feedback Resistor Choice
The value of the feedback resistor is critical for optimum performance on the AD8036 (gain +1) and less critical as the gain increases. Therefore, this section is specifically targeted at the
AD8036.
At minimum stable gain (+1), the AD8036 provides optimum
dynamic performance with RF = 140 Ω. This resistor acts only
as a parasitic suppressor against damped RF oscillations that
can occur due to lead (input, feedback) inductance and parasitic
capacitance. This value of RF provides the best combination of
wide bandwidth, low parasitic peaking, and fast settling time.
In fact, for the same reasons, a 100–130 Ω resistor should be
placed in series with the positive input for other AD8036 noninverting configurations. The correct connection is shown in
Figure 69.
+VS
10mF
R
G = 1+ F
RG
VH
0.1mF
100 - 130V
VIN
AD8036/
AD8037
RTERM
VOUT
0.1mF
10mF
VL
RF
This estimation loses accuracy for gains of +2/–1 or lower due
to the amplifier’s damping factor. For these “low gain” cases,
the bandwidth will actually extend beyond the calculated value
(see Closed-Loop BW plots, Figures 15 and 27).
Pulse Response
Unlike a traditional voltage feedback amplifier, where the slew
speed is dictated by its front end dc quiescent current and gain
bandwidth product, the AD8036 and AD8037 provide “on demand” current that increases proportionally to the input “step”
signal amplitude. This results in slew rates (1200 V/µs) comparable to wideband current feedback designs. This, combined
with relatively low input noise current (2.1 pA/√Hz), gives the
AD8036 and AD8037 the best attributes of both voltage and
current feedback amplifiers.
Large Signal Performance
The outstanding large signal operation of the AD8036 and
AD8037 is due to a unique, proprietary design architecture.
In order to maintain this level of performance, the maximum
350 V-MHz product must be observed, (e.g., @ 100 MHz,
VO ≤ 3.5 V p-p).
Power Supply and Input Clamp Bypassing
Adequate power supply bypassing can be critical when optimizing the performance of a high frequency circuit. Inductance in
the power supply leads can form resonant circuits that produce
peaking in the amplifier’s response. In addition, if large current
transients must be delivered to the load, then bypass capacitors
(typically greater than 1 µF) will be required to provide the best
settling time and lowest distortion. A parallel combination of at
least 4.7 µF, and between 0.1 µF and 0.01 µF, is recommended.
Some brands of electrolytic capacitors will require a small series
damping resistor ≈4.7 Ω for optimum results.
When the AD8036 and AD8037 are used in clamping mode,
and a dc voltage is connected to clamp inputs VH and VL, a 0.1 µF
bypassing capacitor is required between each input pin and
ground in order to maintain stability.
Driving Capacitive Loads
The AD8036 and AD8037 were designed primarily to drive
nonreactive loads. If driving loads with a capacitive component
is desired, the best frequency response is obtained by the addition of a small series resistance as shown in Figure 70. The accompanying graph shows the optimum value for RSERIES vs.
capacitive load. It is worth noting that the frequency response of
the circuit when driving large capacitive loads will be dominated
by the passive roll-off of RSERIES and CL . For capacitive loads of
6 pF or less, no RSERIES is necessary.
RF
–VS
RIN
RG
Figure 69. Noninverting Operation
RIN
AD8036/
AD8037
RSERIES
RL
1kV
For general voltage gain applications, the amplifier bandwidth
can be closely estimated as:
f 3 dB ≅
REV. A
Figure 70. Driving Capacitive Loads
ωO
  RF  
2π 1+ 

  RG  
–15–
CL
AD8036/AD8037
Operation of the AD8036 for negative input voltages and negative clamp levels on VL is similar, with comparator CL controlling S1. Since the comparators see the voltage on the +VIN pin
as their common reference level, then the voltage VH and VL are
defined as “High” or “Low” with respect to +VIN. For example,
if VIN is set to zero volts, VH is open, and VL is +1 V, comparator CL will switch S1 to “C,” so the AD8036 will buffer the
voltage on VL and ignore +VIN.
40
R SERIES – V
30
The performance of the AD8036 and AD8037 closely matches
the ideal just described. The comparator’s threshold extends
from 60 mV inside the clamp window defined by the voltages on
VL and VH to 60 mV beyond the window’s edge. Switch S1 is
implemented with current steering, so that A1’s +input makes a
continuous transition from say, VIN to VH as the input voltage
traverses the comparator’s input threshold from 0.9 V to 1.0 V
for VH = 1.0 V.
20
10
0
5
10
15
20
25
CL– pF
Figure 71. Recommended RSERIES vs. Capacitive Load
INPUT CLAMPING AMPLIFIER OPERATION
The key to the AD8036 and AD8037’s fast, accurate clamp and
amplifier performance is their unique patent pending CLAMPIN
input clamp architecture. This new design reduces clamp errors
by more than 10× over previous output clamp based circuits, as
well as substantially increasing the bandwidth, precision and
versatility of the clamp inputs.
Figure 72 is an idealized block diagram of the AD8036 connected as a unity gain voltage follower. The primary signal path
comprises A1 (a 1200 V/µs, 240 MHz high voltage gain, differential to single-ended amplifier) and A2 (a G = +1 high current
gain output buffer). The AD8037 differs from the AD8036 only
in that A1 is optimized for closed-loop gains of two or greater.
The CLAMPIN section is comprised of comparators CH and
CL, which drive switch S1 through a decoder. The unity-gain
buffers in series with +VIN, VH , and VL inputs isolate the input
pins from the comparators and S1 without reducing bandwidth
or precision.
The two comparators have about the same bandwidth as A1
(240 MHz), so they can keep up with signals within the useful
bandwidth of the AD8036. To illustrate the operation of the
CLAMPIN circuit, consider the case where VH is referenced to
+1 V, VL is open, and the AD8036 is set for a gain of +1, by
connecting its output back to its inverting input through the recommended 140 Ω feedback resistor. Note that the main signal
path always operates closed loop, since the CLAMPIN circuit
only affects A1’s noninverting input.
The practical effect of these nonidealities is to soften the
transition from amplification to clamping modes, without compromising the absolute clamp limit set by the CLAMPIN circuit. Figure 73 is a graph of VOUT vs. VIN for the AD8036 and a
typical output clamp amplifier. Both amplifiers are set for G =
+1 and VH = +1 V.
The worst case error between VOUT (ideally clamped) and VOUT
(actual) is typically 18 mV times the amplifier closed-loop gain.
This occurs when VIN equals VH (or VL). As VIN goes above
and/or below this limit, VOUT will settle to within 5 mV of the
ideal value.
In contrast, the output clamp amplifier’s transfer curve typically
will show some compression starting at an input of 0.8 V, and
can have an output voltage as far as 200 mV over the clamp
limit. In addition, since the output clamp in effect causes the
amplifier to operate open loop in clamp mode, the amplifier’s
output impedance will increase, potentially causing additional
errors.
The AD8036’s and AD8037’s CLAMPIN input clamp architecture works only for noninverting or follower applications and,
since it operates on the input, the clamp voltage levels VH and
VL, and input error limits will be multiplied by the amplifier’s
RF
140V
–VIN
+VIN
+1
VH
+1
VL
+1
A1
A
A2
+1
VOUT
S1
If a 0 V to +2 V voltage ramp is applied to the AD8036’s +VIN
for the connection just described, VOUT should track +VIN perfectly up to +1 V, then should limit at exactly +1 V as +VIN continues to +2 V.
In practice, the AD8036 comes close to this ideal behavior. As
the +VIN input voltage ramps from zero to 1 V, the output of the
high limit comparator CH starts in the off state, as does the output of CL. When +VIN just exceeds VIN (ideally, by say 1 µV,
practically by about 18 mV), CH changes state, switching S1
from “A” to “B” reference level. Since the + input of A1 is now
connected to VH, further increases in +VIN have no effect on the
AD8036’s output voltage. In short, the AD8036 is now operating as a unity-gain buffer for the VH input, as any variation in
VH, for VH > 1 V, will be faithfully reproduced at VOUT.
–16–
B
C
S1
CH
VIN > VH
A B C
0 1 0
VL ≤ VIN ≤ VH 1 0 0
VIN < VL
0 0 1
CL
Figure 72. AD8036/AD8037 Clamp Amp System
REV. A
AD8036/AD8037
closed-loop gain at the output. For instance, to set an output
limit of ± 1 V for an AD8037 operating at a gain of 3.0, VH and
VL would need to be set to +0.333 V and –0.333 V, respectively.
The only restriction on using the AD8036’s and AD8037’s
+VIN, VL, VH pins as inputs is that the maximum voltage difference between +VIN and VH or V L should not exceed 6.3 V, and
all three voltages be within the supply voltage range. For example, if VL is set at –3 V, then VIN should not exceed +3.3 V.
Clamping with Gain
Figure 75 shows an AD8037 configured for a noninverting gain
of two. The AD8037 is used in this circuit since it is compensated for gains of two or greater and provides greater bandwidth. In this case, the high clamping level at the output will
VH
0.1mF
+5V
0.1mF
1.6
10mF
130V
VIN
VH
AD8036
OUTPUT VOLTAGE – VOUT
1.4
VOUT
VL
0.1mF
1.2
10mF
0.1mF
CLAMP ERROR – 25mV
AD8036
–5V
CLAMP ERROR – >200mV
OUTPUT CLAMP
RF
140V
VL
1.0
AD8036
0.6
0.6
Figure 74. Unity Gain Noninverting Clamp
OUTPUT CLAMP AMP
0.8
0.8
1.0
1.2
1.4
1.6
INPUT VOLTAGE – +VIN
1.8
occur at 2 × VH and the low clamping level at the output will be
2 × VL. The equations governing the output clamp levels in circuits configured for noninverting gain are:
2.0
VCH = G × VH
VCL = G × VL
Figure 73. Output Clamp Error vs. Input Clamp Error
where:
AD8036/AD8037 APPLICATIONS
The AD8036 and AD8037 use a unique input clamping circuit
to perform the clamping function. As a result, they provide the
clamping function better than traditional output clamping devices and provide additional flexibility to perform other unique
applications.
VCH is the high output clamping level
VCL is the low output clamping level
G is the gain of the amplifier configuration
VH is the high input clamping level (Pin 8)
VL is the low input clamping level (Pin 5)
*Amplifier offset is assumed to be zero.
VH
There are, however, some restrictions on circuit configurations;
and some calculations need to be performed in order to figure
the clamping level, as a result of clamping being performed at
the input stage.
0.1mF
+5V
0.1mF
10mF
100V
The major restriction on the clamping feature of the AD8036/
AD8037 is that clamping occurs only when using the amplifiers
in the noninverting mode. To clamp in an inverting circuit, an
additional inverting gain stage is required. Another restriction is
that VH be greater than VL, and that each be within the output
voltage range of the amplifier (± 3.9 V). VH can go below ground
and VL can go above ground as long as VH is kept higher than VL.
VIN
VH
49.9V
AD8037
VOUT
VL
0.1mF
10mF
0.1mF
–5V
RG
274V
VL
RF
274V
Unity Gain Clamping
The simplest circuit for calculating the clamp levels is a unity
gain follower as shown in Figure 74. In this case, the AD8036
should be used since it is compensated for noninverting unity
gain.
Figure 75. Gain of Two Noninverting Clamp
This circuit will clamp at an upper voltage set by VH (the voltage
applied to Pin 8) and a lower voltage set by VL (the voltage applied to Pin 5).
REV. A
–17–
AD8036/AD8037
+5V
806V
+5V
0.1mF
100V
+5V
0.1mF
–0.5V to +0.5V
10µF
0.1mF
AD780
2.5V
49.9V
–2V to 0V
AD8037
0.1mF
100V
R1
499V
49.9V
VIN = –2V TO 0V
CLAMPING
RANGE
–2.1V to +0.1V
VL
0.1mF
806V
1N5712
AD9002
VH
R3
750V
10mF
100V
VIN
10mF
SUBSTRATE
DIODE
–5V
0.1mF
0.1mF
R2
301V
–5V
–5.2V
Figure 76. Gain of Two, Noninverting with Offset AD8037 Driving an AD9002—8-Bit, 125 MSPS A/D Converter
Clamping with an Offset
Some op amp circuits are required to operate with an offset
voltage. These are generally configured in the inverting mode
where the offset voltage can be summed in as one of the inputs.
Since AD8036/AD8037 clamping does not function in the inverting mode, it is not possible to clamp with this configuration.
Figure 76 shows a noninverting configuration of an AD8037
that provides clamping and also has an offset.␣ The circuit shows
the AD8037 as a driver for an AD9002, an 8-bit, 125 Msps
A/D converter and illustrates some of the considerations for using an AD8037 with offset and clamping.
VCH = VOFF + G × VH
VCL = VOFF + G × VL
Where VOFF is the offset voltage that appears at the output.
When an offset is added to a noninverting op amp circuit, it is
fed in through a resistor to the inverting input. The result is that
the op amp must now operate at a closed-loop gain greater than
unity. For this circuit a gain of two was chosen which allows the
use of the AD8037. The feedback resistor, R2, is set at 301 Ω
for optimum performance of the AD8037 at a gain of two.
There is an interaction between the offset and the gain, so some
calculations must be performed to arrive at the proper values for
R1 and R3. For a gain of two the parallel combination of resistors R1 and R3 must be equal to the feedback resistor R2. Thus
R1 × R3/R1 + R3 = R2 = 301 Ω
2.5 V × R1/(R1 + R3) = 1 V
When the two equations are solved simultaneously we get R1 =
499 Ω and R3 = 750 Ω (using closest 1% resistor values in all
cases). This positive 1 V offset at the input translates to a –1 V
offset at the output.
The usable input signal swing of the AD9002 is 2 V p-p. This is
centered about the –1 V offset making the usable signal range
from 0 V to –2 V. It is desirable to clamp the input signal so
Because the clamping is done at the input stage of the AD8037,
the clamping level as seen at the output is affected by not only
the gain of the circuit as previously described, but also by the
offset. Thus, in order to obtain the desired clamp levels, VH
must be biased at +0.55 V while VL must be biased at –0.55 V.
The clamping levels as seen at the output can be calculated by
the following:
The analog input range of the AD9002 is from ground to –2 V.
The input should not go more than 0.5 V outside this range in
order to prevent disruptions to the internal workings of the A/D
and to avoid drawing excess current. These requirements make
the AD8037 a prime candidate for signal conditioning.
The reference used to provide the offset is the AD780 whose
output is 2.5 V. This must be divided down to provide the 1 V
offset desired. Thus
that it goes no more than 100 mV outside of this range in either
direction. Thus, the high clamping level should be set at +0.1 V
and the low clamping level should be set at –2.1 V as seen at the
input of the AD9002 (output of AD8037).
The resistors used to generate the voltages for VH and VL should
be kept to a minimum in order to reduce errors due to clamp
bias current. This current is dependent on VH and VL (see Figure 61) and will create a voltage drop across whatever resistance
is in series with each clamp input. This extra error voltage is
multiplied by the closed-loop gain of the amplifier and can be
substantial, especially in high closed-loop gain configurations. A
0.1 µF bypass capacitor should be placed between input clamp
pins VH and VL and ground to ensure stable operation.
The 1N5712 Schottky diode is used for protection from forward
biasing the substrate diode in the AD9002 during power-up
transients.
Programmable Pulse Generator
The AD8036/AD8037’s clamp output can be set accurately and
has a well controlled flat level. This along with wide bandwidth
and high slew rate make them very well suited for programmable
level pulse generators.
Figure 77 is a schematic for a pulse generator that can directly
accept TTL generated timing signals for its input and generate
pulses at the output up to 24 V p-p with 2500 V/µs slew rate.
The output levels can be programmed to anywhere in the range
–12 V to +12 V.
–18–
REV. A
AD8036/AD8037
VH
0.1mF
+5V
+15V
0.1mF
200V
10mF
100V
TTLIN
VH
1.3kV
0.1mF
100V
AD8037
VL
10mF
VL 3 10
PULSE
OUT
AD811
–15V
0.1mF
VH 3 10
10mF
0.1mF
0.1mF
–5V
VL
–15V
274V
10mF
604V
150V
274V
Figure 77. Programmable Pulse Generator
The circuit uses an AD8037 operating at a gain of two with an
AD811 to boost the output to the ± 12 V range. The AD811 was
chosen for its ability to operate with ± 15 V supplies and its high
slew rate.
The circuit is configured as an inverting amplifier with a gain
of one. The input drives the inverting amplifier and also directly
drives VL, the lower level clamping input. The high level clamping input, VH, is left floating and plays no role in this circuit.
R1 and R2 act as a level shifter to make the TTL signal levels be
approximately symmetrical above and below ground. This ensures that both the high and low logic levels will be clamped by
the AD8037. For well controlled signal levels in the output
pulse, the high and low output levels should result from the
clamping action of the AD8037 and not be controlled by either
the high or low logic levels passing through a linear amplifier.
For good rise and fall times at the output pulse, a logic family
with high speed edges should be used.
When the input is negative, the amplifier acts as a regular unitygain inverting amplifier and outputs a positive signal at the same
amplitude as the input with opposite polarity. VL is driven negative by the input, so it performs no clamping action, because the
positive output signal is always higher than the negative level
driving VL.
The high logic levels are clamped at two times the voltage at VH ,
while the low logic levels are clamped at two times the voltage
at VL. The output of the AD8037 is amplified by the AD811
operating at a gain of 5. The overall gain of 10 will cause the
high output level to be 10 times the voltage at VH, and the low
output level to be 10 times the voltage at VL.
High Speed, Full-Wave Rectifier
The clamping inputs are additional inputs to the input stage of
the op amp. As such they have an input bandwidth comparable
to the amplifier inputs and lend themselves to some unique
functions when they are driven dynamically.
When the input is positive, the output result is the sum of two
separate effects. First, the inverting amplifier multiplies the input by –1 because of its unity-gain inverting configuration. This
effectively produces an offset as explained above, but with a dynamic level that is equal to –1 times the input.
Second, although the positive input is grounded (through 100 Ω),
the output is clamped at two times the voltage applied to VL (a
positive, dynamic voltage in this case). The factor of two is because the noise gain of the amplifier is two.
The sum of these two actions results in an output that is equal
to unity times the input signal for positive input signals, see Figure 79. For a input/output scope photo with an input signal of
20 MHz and amplitude ± 1 V, see Figure 80.
Figure 78 is a schematic for a full-wave rectifier, sometimes
called an absolute value generator. It works well up to 20 MHz
and can operate at significantly higher frequencies with some
degradation in performance. The distortion performance is significantly better than diode based full-wave rectifiers, especially
at high frequencies.
INPUT
LOWER
CLAMPING
LEVEL WITH
NO NEG INPUT
+5V
0.1mF
FULL WAVE
RECTIFIED
OUTPUT
10mF
100V
VH
AD8037
VOUT = VIN
VL
0.1mF
RG
274V
RF
274V
LOWER
CLAMPING
LEVEL
–1 3 INPUT
10mF
OUTPUT
–5V
VIN
Figure 79.
Figure 78. Full-Wave Rectifier
REV. A
–19–
AD8036/AD8037
The modulation signal is applied to both the input of a unity
gain inverting amplifier and to VL, the lower clamping input.
VH is biased at +0.5 V dc.
To understand the circuit operation, it is helpful to first consider a simpler circuit. If both VL and VH were dc biased at
–0.5 V and the carrier and modulation inputs driven as above,
the output would be a 2 V p-p square wave at the carrier frequency riding on a waveform at the modulating frequency. The
inverting input (modulation signal) is creating a varying offset to
the 2 V p-p square wave at the output. Both the high and low
levels clamp at twice the input levels on the clamps because the
noise gain of the circuit is two.
Figure 80. Full-Wave Rectifier Scope
When VL is driven by the modulation signal instead of being
held at a dc level, a more complicated situation results. The resulting waveform is composed of an upper envelope and a lower
envelope with the carrier square wave in between. The upper
and lower envelope waveforms are 180° out of phase as in a
typical AM waveform.
Thus for either positive or negative input signals, the output is
unity times the absolute value of the input signal. The circuit
can be easily configured to produce the negative absolute value
of the input by applying the input to VH instead of VL.
The circuit can get to within about 40 mV of ground during the
time when the input crosses zero. This voltage is fixed over a
wide frequency range and is a result of the switching between
the conventional op amp input and the clamp input. But because there are no diodes to rapidly switch from forward to reverse bias, the performance far exceeds that of diode based full
wave rectifiers.
The upper envelope is produced by the upper clamp level being
offset by the waveform applied to the inverting input. This offset
is the opposite polarity of the input waveform because of the
inverting configuration.
The 40 mV offset mentioned can be removed by adding an offset to the circuit. A 27.4 kΩ input resistor to the inverting input
will have a gain of 0.01, while changing the gain of the circuit by
only 1%. A plus or minus 4 V dc level (depending on the polarity of the rectifier) into this resistor will compensate for the
offset.
Full wave rectifiers are useful in many applications including
AM signal detection, high frequency ac voltmeters and various
arithmetic operations.
Amplitude Modulator
In addition to being able to be configured as an amplitude demodulator (AM detector), the AD8037 can also be configured
as an amplitude modulator as shown in Figure 81.
The lower envelope is produced by the sum of two effects. First,
it is offset by the waveform applied to the inverting input as in
the case of the simplified circuit above. The polarity of this offset is in the same direction as the upper envelope. Second, the
output is driven in the opposite direction of the offset at twice
the offset voltage by the modulation signal being applied to VL.
This results from the noise gain being equal to two, and since
there is no inversion in this connection, it is opposite polarity
from the offset.
The result at the output for the lower envelope is the sum of
these two effects, which produces the lower envelope of an amplitude modulated waveform. See Figure 82.
VH +5V
0.1mF
10mF
100V
CARRIER IN
VH
AD8037
AM OUT
VL
0.1mF
RG
274V
RF
274V
10mF
–5V
MODULATION IN
Figure 81. Amplitude Modulator
The positive input of the AD8037 is driven with a square wave
of sufficient amplitude to produce clamping action at both the
high and low levels. This is the higher frequency carrier signal.
Figure 82. AM Waveform
The depth of modulation can be modified in this circuit by
changing the amplitude of the modulation signal. This changes
the amplitude of the upper and lower envelope waveforms.
The modulation depth can also be changed by changing the dc
bias applied to VH . In this case the amplitudes of the upper and
lower envelope waveforms stay constant, but the spacing between them changes. This alters the ratio of the envelope amplitude to the amplitude of the overall waveform.
–20–
REV. A
AD8036/AD8037
Layout Considerations
VH
The specified high speed performance of the AD8036 and
AD8037 requires careful attention to board layout and component selection. Proper RF design techniques and low pass parasitic component selection are mandatory.
+VS
1kV
RF
–VS
0.1mF
The PCB should have a ground plane covering all unused portions of the component side of the board to provide a low impedance path. The ground plane should be removed from the
area near the input pins to reduce stray capacitance.
+VS
RG
RS
Chip capacitors should be used for supply and input clamp bypassing (see Figure 83). One end should be connected to the
ground plane and the other within 1/8 inch of each power and
clamp pin. An additional large (0.47 µF–10 µF) tantalum electrolytic capacitor should be connected in parallel, though not
necessarily so close, to supply current for fast, large signal
changes at the output.
RO
AD8036/
AD8037
VOUT
IN
RT
–VS
+VS
0.1mF
1kV
VL
–VS
NONINVERTING CONFIGURATION
The feedback resistor should be located close to the inverting
input pin in order to keep the stray capacitance at this node to a
minimum. Capacitance variations of less than 1 pF at the inverting input will significantly affect high speed performance.
+VS
OPTIONAL
Stripline design techniques should be used for long signal traces
(greater than about 1 inch). These should be designed with a
characteristic impedance of 50 Ω or 75 Ω and be properly terminated at each end.
Evaluation Board
C1
0.01mF
C3
0.1mF
C5
10mF
C2
0.01mF
C4
0.1mF
C6
10mF
–VS
SUPPLY BYPASSING
Figure 83. Noninverting Configurations for Evaluation
Boards
An evaluation board for both the AD8036 and AD8037 is available that has been carefully laid out and tested to demonstrate
that the specified high speed performance of the device can be
realized. For ordering information, please refer to the Ordering
Guide.
The layout of the evaluation board can be used as shown or
serve as a guide for a board layout.
Table I.
REV. A
Component
+1
+2
RF
RG
RO (Nominal)
RS
RT (Nominal)
Small Signal BW (MHz)
140 Ω
274 Ω
274 Ω
49.9 Ω
100 Ω
49.9 Ω
90
49.9 Ω
130 Ω
49.9 Ω
240
AD8036A
Gain
+10
2 kΩ
221 Ω
49.9 Ω
100 Ω
49.9 Ω
10
–21–
+100
+2
AD8037A
Gain
+10
+100
2 kΩ
20.5 Ω
49.9 Ω
100 Ω
49.9 Ω
1.3
274 Ω
274 Ω
49.9 Ω
100 Ω
49.9 Ω
275
2 kΩ
221 Ω
49.9 Ω
100 Ω
49.9 Ω
21
2 kΩ
20.5 Ω
49.9 Ω
100 Ω
49.9 Ω
3
AD8036/AD8037
Figure 84. Evaluation Board Silkscreen (Top)
Figure 86. Board Layout (Solder Side)
Figure 85. Evaluation Board Silkscreen (Bottom)
Figure 87. Board Layout (Component Side)
–22–
REV. A
AD8036/AD8037
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
8-Lead Plastic DIP
(N Package)
8
C1980a–0–9/99
0.430 (10.92)
0.348 (8.84)
5
0.280 (7.11)
0.240 (6.10)
1
4
0.325 (8.25)
0.300 (7.62)
PIN 1
0.100 (2.54)
BSC
0.060 (1.52)
0.015 (0.38)
0.210
(5.33)
MAX
0.195 (4.95)
0.115 (2.93)
0.130
(3.30)
MIN
0.160 (4.06)
0.115 (2.93)
0.015 (0.381)
0.008 (0.204)
0.022 (0.558) 0.070 (1.77) SEATING
0.014 (0.356) 0.045 (1.15) PLANE
8-Lead Plastic SOIC
(SO Package)
0.1968 (5.00)
0.1890 (4.80)
0.1574 (4.00)
0.1497 (3.80)
8
5
1
4
0.2440 (6.20)
0.2284 (5.80)
PIN 1
0.0196 (0.50)
3 458
0.0099 (0.25)
0.0500 (1.27)
BSC
0.0688 (1.75)
0.0532 (1.35)
0.0098 (0.25)
0.0040 (0.10)
SEATING
PLANE
88
0.0500 (1.27)
0.0098 (0.25) 08
0.0160 (0.41)
0.0075 (0.19)
0.0192 (0.49)
0.0138 (0.35)
8-Lead Cerdip
(Q Package)
0.005 (0.13)
MIN
8
0.055 (1.4)
MAX
5
0.310 (7.87)
0.220 (5.59)
PIN 1
1
4
0.200.(5.08)
MAX
0.200 (5.08)
0.125 (3.18)
0.060 (1.52)
0.015 (0.38)
0.150
(3.81)
MIN
SEATING
0.023 (0.58) 0.070 (1.78) PLANE
0.014 (0.36) 0.030 (0.76)
REV. A
–23–
0.320 (8.13)
0.290 (7.37)
15°
0°
0.015 (0.38)
0.008 (0.20)
PRINTED IN U.S.A.
0.100 (2.54) BSC
0.405 (10.29) MAX