2PB1424 20 V, 3 A PNP low VCEsat (BISS) transistor Rev. 01 — 2 May 2005 Product data sheet 1. Product profile 1.1 General description PNP low VCEsat Breakthrough in Small Signal (BISS) transistor in a SOT89 (SC-62/ TO-243) SMD plastic package. NPN complement: 2PD2150. 1.2 Features ■ ■ ■ ■ ■ Low collector-emitter saturation voltage VCEsat High collector current capability: IC and ICM High collector current gain (hFE) at high IC High efficiency due to less heat generation Smaller required Printed-Circuit Board (PCB) area than for conventional transistors 1.3 Applications ■ ■ ■ ■ ■ ■ DC-to-DC conversion MOSFET gate driving Motor control Charging circuits Power switches (e.g. motors, fans) Thin Film Transistor (TFT) backlight inverter 1.4 Quick reference data Table 1: Quick reference data Symbol Parameter Conditions Min Typ Max Unit VCEO collector-emitter voltage open base - - −20 V ICM peak collector current single pulse; tp ≤ 1 ms - - −3 A hFE DC current gain VCE = −2 V; IC = −0.1 A 180 - 390 2PB1424 Philips Semiconductors 20 V, 3 A PNP low VCEsat (BISS) transistor 2. Pinning information Table 2: Pinning Pin Description 1 emitter 2 collector 3 base Simplified outline Symbol 2 3 3 2 1 1 sym079 3. Ordering information Table 3: Ordering information Type number Package Name Description Version 2PB1424 SC-62 plastic surface mounted package; collector pad for good heat transfer; 3 leads SOT89 4. Marking Table 4: Marking codes Type number Marking code 2PB1424 M1 9397 750 15061 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 2 May 2005 2 of 11 2PB1424 Philips Semiconductors 20 V, 3 A PNP low VCEsat (BISS) transistor 5. Limiting values Table 5: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter Conditions Min Max Unit VCBO collector-base voltage open emitter - −40 V VCEO collector-emitter voltage open base - −20 V VEBO emitter-base voltage open collector - −5 V IC collector current (DC) - −1 A ICM peak collector current single pulse; tp ≤ 1 ms - −3 A Ptot total power dissipation Tamb ≤ 25 °C [1] - 500 mW [2] - 850 mW [3] - 1200 mW Tj junction temperature - 150 °C Tamb ambient temperature −65 +150 °C Tstg storage temperature −65 +150 °C [1] Device mounted on an FR4 PCB, single-sided copper, tin-plated and standard footprint. [2] Device mounted on an FR4 PCB, single-sided copper, tin-plated, mounting pad for collector 1 cm2. [3] Device mounted on an FR4 PCB, single-sided copper, tin-plated, mounting pad for collector 6 cm2. 006aaa449 1600 Ptot (mW) (1) 1200 (2) 800 (3) 400 0 −65 −35 −5 25 55 85 115 145 175 Tamb (°C) (1) FR4 PCB; mounting pad for collector 6 cm2 (2) FR4 PCB; mounting pad for collector 1 cm2 (3) FR4 PCB; standard footprint Fig 1. Power derating curves 9397 750 15061 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 2 May 2005 3 of 11 2PB1424 Philips Semiconductors 20 V, 3 A PNP low VCEsat (BISS) transistor 6. Thermal characteristics Table 6: Thermal characteristics Symbol Parameter Rth(j-a) Conditions thermal resistance from junction to ambient in free air Min Typ Max Unit [1] - - 250 K/W [2] - - 147 K/W [3] Rth(j-sp) thermal resistance from junction to solder point - - 104 K/W - - 20 K/W [1] Device mounted on an FR4 PCB, single-sided copper, tin-plated and standard footprint. [2] Device mounted on an FR4 PCB, single-sided copper, tin-plated, mounting pad for collector 1 cm2. [3] Device mounted on an FR4 PCB, single-sided copper, tin-plated, mounting pad for collector 6 cm2. 006aaa450 103 Zth(j-a) (K/W) 102 duty cycle = 1.00 0.50 0.75 0.33 0.20 10 0.10 0.05 0.02 0.01 1 0.00 10−1 10−5 10−4 10−3 10−2 10−1 1 10 102 t p (s) 103 FR4 PCB; mounting pad for collector 1 cm2 Fig 2. Transient thermal impedance from junction to ambient as a function of pulse time; typical values 9397 750 15061 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 2 May 2005 4 of 11 2PB1424 Philips Semiconductors 20 V, 3 A PNP low VCEsat (BISS) transistor 7. Characteristics Table 7: Characteristics Tamb = 25 °C unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit ICBO collector-base cut-off current VCB = −30 V; IE = 0 A - - −0.1 µA VCB = −30 V; IE = 0 A; Tj = 150 °C - - −10 µA VEB = −5 V; IC = 0 A - - −0.1 µA IEBO emitter-base cut-off current hFE DC current gain VCE = −2 V; IC = −0.1 A VCEsat collector-emitter saturation voltage IC = −2 A; IB = −100 mA VBEon base-emitter turn-on voltage fT transition frequency Cc collector capacitance [1] 180 - 390 - - −0.5 V VCE = −10 V; IC = −5 mA - - −0.7 V VCE = −1 V; IC = −1 A - - −1 V VCE = −2 V; IC = −500 mA; f = 100 MHz - 140 - MHz VCB = −10 V; IE = ie = 0 A; f = 1 MHz - 27 - pF [1] Pulse test: tp ≤ 300 µs; δ ≤ 0.02 9397 750 15061 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 2 May 2005 5 of 11 2PB1424 Philips Semiconductors 20 V, 3 A PNP low VCEsat (BISS) transistor 006aaa457 −3 IB (mA) −25 hFE −20 −17.5 IC (A) 006aaa458 500 −22.5 (1) 400 −15 −12.5 −2 300 −10 (2) −7.5 200 −5 −1 (3) −2.5 0 0 −1 −2 −3 −4 100 0 −5 VCE (V) 1 102 10 103 104 IC (mA) VCE = −2 V Tamb = 25 ˚C (1) Tamb = 100 ˚C (2) Tamb = 25 ˚C (3) Tamb = −55 ˚C Fig 3. Collector current as a function of collector-emitter voltage; typical values Fig 4. DC current gain as a function of collector current; typical values 006aaa459 −1 006aaa460 −1 VCEsat (mV) VCEsat (mV) −10−1 −10−1 (1) (1) (2) (3) (3) −10−2 −10−3 −10−1 (2) −10−2 −1 −10 −102 −103 −104 IC (mA) IC/IB = 10 −10−3 −10−1 −1 −102 −103 −104 IC (mA) IC/IB = 20 (1) Tamb = 100 ˚C (1) Tamb = 100 ˚C (2) Tamb = 25 ˚C (2) Tamb = 25 ˚C (3) Tamb = −55 ˚C (3) Tamb = −55 ˚C Fig 5. Collector-emitter saturation voltage as a function of collector current; typical values Fig 6. Collector-emitter saturation voltage as a function of collector current; typical values 9397 750 15061 Product data sheet −10 © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 2 May 2005 6 of 11 2PB1424 Philips Semiconductors 20 V, 3 A PNP low VCEsat (BISS) transistor 8. Package outline 4.6 4.4 1.8 1.4 1.6 1.4 2.6 2.4 4.25 3.75 1 2 0.53 0.40 1.5 1.2 0.8 3 0.48 0.35 0.44 0.23 3 Dimensions in mm 04-08-03 Fig 7. Package outline SOT89 (SC-62/TO-243) 9. Packing information Table 8: Packing methods The indicated -xxx are the last three digits of the 12NC ordering code. [1] Type number 2PB1424 [1] Package SOT89 Description 8 mm pitch, 12 mm tape and reel 1000 4 000 -115 -135 For further information and the availability of packing methods, see Section 17. 9397 750 15061 Product data sheet Packing quantity © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 2 May 2005 7 of 11 2PB1424 Philips Semiconductors 20 V, 3 A PNP low VCEsat (BISS) transistor 10. Soldering 4.75 2.25 2.00 1.90 1.20 solder lands 0.85 0.20 solder resist occupied area 1.70 1.20 solder paste 4.60 4.85 0.50 1.20 1.00 (3x) 1.20 3 2 1 msa442 0.60 (3x) 0.70 (3x) 3.70 3.95 SOT89 standard mounting conditions for reflow soldering Dimensions in mm Fig 8. Reflow soldering footprint SOT89 (SC-62/TO-243) 11. Mounting 32 mm 10 mm 40 mm 10 mm 2.5 mm 1 mm 0.5 mm 5 mm 3.96 mm 1.6 mm 001aab105 Fig 9. FR4 PCB; mounting pad for collector 1 cm2 9397 750 15061 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 2 May 2005 8 of 11 2PB1424 Philips Semiconductors 20 V, 3 A PNP low VCEsat (BISS) transistor 12. Revision history Table 9: Revision history Document ID Release date Data sheet status Change notice Doc. number Supersedes 2PB1424_1 20050502 Product data sheet - 9397 750 15061 - 9397 750 15061 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 2 May 2005 9 of 11 2PB1424 Philips Semiconductors 20 V, 3 A PNP low VCEsat (BISS) transistor 13. Data sheet status Level Data sheet status [1] Product status [2] [3] Definition I Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. II Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. III Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). [1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. [3] For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. 14. Definitions customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Right to make changes — Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status ‘Production’), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. 16. Trademarks 15. Disclaimers Notice — All referenced brands, product names, service names and trademarks are the property of their respective owners. Life support — These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors 17. Contact information For additional information, please visit: http://www.semiconductors.philips.com For sales office addresses, send an email to: [email protected] 9397 750 15061 Product data sheet © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Rev. 01 — 2 May 2005 10 of 11 2PB1424 Philips Semiconductors 20 V, 3 A PNP low VCEsat (BISS) transistor 18. Contents 1 1.1 1.2 1.3 1.4 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Product profile . . . . . . . . . . . . . . . . . . . . . . . . . . 1 General description. . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick reference data. . . . . . . . . . . . . . . . . . . . . 1 Pinning information . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 3 Thermal characteristics. . . . . . . . . . . . . . . . . . . 4 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Package outline . . . . . . . . . . . . . . . . . . . . . . . . . 7 Packing information. . . . . . . . . . . . . . . . . . . . . . 7 Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . 9 Data sheet status . . . . . . . . . . . . . . . . . . . . . . . 10 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Contact information . . . . . . . . . . . . . . . . . . . . 10 © Koninklijke Philips Electronics N.V. 2005 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 2 May 2005 Document number: 9397 750 15061 Published in The Netherlands