MIG150Q201H TOSHIBA Intelligent Power Module Silicon N Channel IGBT MIG150Q201H High Power Switching Applications Motor Control Applications l Integrates inverter, brake power circuits & control circuits (IGBT drive units, protection units for over-current, under-voltage & over-temperature) in one package. l The electrodes are isolated from case. Equivalent Circuit 1 2001-05-29 MIG150Q201H Maximum Ratings (Tj = 25°C) Stage Characteristic Condition Supply voltage P-N power terminal Collector-emitter voltage Inverter ― VCC 900 V VCES 1200 V IC 150 A Forward current Tc = 25°C, DC IF 150 A Collector power dissipation Tc = 25°C PC 800 W Tj 150 °C VCC 900 V VCES 1200 V ― P-N power terminal Collector-emitter voltage ― Collector current Tc = 25°C, DC IC 50 A Reverse voltage ― VR 1200 V Forward current Tc = 25°C, DC IF 50 A Collector power dissipation Tc = 25°C PC 350 W Tj 150 °C Junction temperature Module Unit Tc = 25°C, DC Supply voltage Control Ratings Collector current Junction temperature Brake Symbol ― Control supply voltage VD-GND terminal VD 20 V Input voltage IN-GND terminal VIN 20 V Fault output voltage FO-GND (L) terminal VFO 20 V Fault output current FO sink current IFO 10 mA Operating temperature ― TC −20 ~ +100 °C Storage temperature range ― Tstg −40 ~ +125 °C VISO 2500 V ― 3 N·m Isolation voltage AC 1 minute Screw torque M5 Electrical Characteristics (Tj = 25°C) a. Inverter Stage Characteristic Collector cut-off current Collector-emitter saturation voltage Forward voltage Symbol ICEX VCE (sat) VF Test Condition Min Typ. Max Tj = 25°C ― ― 1 Tj = 125°C ― ― 20 VD = 15 V, IC = 150 A Tj = 25°C VIN = 3 V → 0 V Tj = 125°C ― 2.6 3.5 ― 2.5 ― IF = 150 A ― 2.2 3.0 0.8 1.5 2.1 ― 0.7 1.4 ― 0.18 0.25 ― 1.3 2.2 ― 0.25 0.5 VCE = 1200 V ton tc(on) Switching time trr VCC = 600 V, IC = 150 A VD = 15 V, VIN = 3 V 0V Inductive load toff (Note 1) tc(off) 2 Unit mA V V µs 2001-05-29 MIG150Q201H b. Brake Stage (Tj = 25°C) Characteristic Collector cut-off current Symbol ICEX Collector-emitter saturation voltage VCE (sat) Test Condition VCE = 1200V VD = 15V, IC = 50A VIN = 3V → 0V Reverse current IR VR = 1200V Forward voltage VF IF = 50A Min Typ. Max Tj = 25°C ― ― 1 Tj = 125°C ― ― 20 Tj = 25°C ― 2.7 3.5 Tj = 125°C ― 2.5 ― Tj = 25°C ― ― 1 Tj = 125°C ― ― 20 ― 1.4 2.2 0.7 1.4 2.0 ― 0.85 1.6 ― 0.42 0.5 ― 1.9 2.6 ― 0.4 0.8 Min Typ. Max ― 20 30 ― 80 120 0.9 1.1 1.3 8 10 12 ― ― 0.1 230 320 ― 80 110 ― 320 400 ― 120 150 ― ― 5 ― 111 118 125 ― 98 ― 11.3 12.0 12.7 11.8 12.5 13.2 1 2 3 ton tc(on) Switching time trr VCC = 600V, IC = 50A VD = 15V, VIN = 3V 0V Inductive load toff (Note 1) tc(off) c. Unit mA V mA V µs Control Stage (Tj = 25°C) Characteristic Control circuit current Symbol High side ID (H) Low side ID (L) Input-on signal voltage VIN (on) Fault output current Protection IFO (on) Normal IFO (off) Over current protection trip level Inverter Short current protection trip level Inverter Brake Brake Over current cut-off time VD = 15 V VD = 15 V, IC = 150 mA VD = 15 V OC VD = 15 V, Tj ≤ 125°C SC VD = 15 V, Tj ≤ 125°C toff (OC) Over temperature protection Trip level OT Reset level OTr Control supply under voltage protection Trip level UV Reset level UVr Fault output pulse width Test Condition tFO VD = 15 V Case temperature ― VD = 15 V 3 Unit mA V mA A A µs °C V ms 2001-05-29 MIG150Q201H d. Thermal Resistance (Tj = 25°C) Characteristic Junction to case thermal resistance Case to fin thermal resistance Symbol Rth (j-c) Rth (c-f) Test Condition Min Typ. Max Inverter IGBT ― ― 0.156 Inverter FRD ― ― 0.5 Brake IGBT ― ― 0.36 Brake FRD ― ― 1.0 Compound is applied ― 0.04 ― Unit °C / W °C / W Note 1: Switching time test circuit & timing chart 4 2001-05-29 MIG150Q201H Package Dimensions: TOSHIBA 2-136A1A Unit: mm 5 2001-05-29 MIG150Q201H RESTRICTIONS ON PRODUCT USE 000707EAA · TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc.. · The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer’s own risk. · The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of TOSHIBA CORPORATION or others. · The information contained herein is subject to change without notice. 6 2001-05-29