Philips Semiconductors Preliminary specification Silicon Diffused Power Transistor BUJ303AX GENERAL DESCRIPTION High-voltage, high-speed planar-passivated npn power switching transistor in a plastic full-pack envelope intended for use in high frequency electronic lighting ballast applications, converters, inverters, switching regulators, motor control systems, etc. QUICK REFERENCE DATA SYMBOL PARAMETER CONDITIONS TYP. MAX. UNIT VCESM VCBO VCEO IC ICM Ptot VCEsat hFEsat tf Collector-emitter voltage peak value Collector-Base voltage (open emitter) Collector-emitter voltage (open base) Collector current (DC) Collector current peak value Total power dissipation Collector-emitter saturation voltage DC current gain Fall time VBE = 0 V 0.25 12 145 1000 1000 500 5 10 32 1.5 160 V V V A A W V PINNING - SOT186A PIN Ths ≤ 25 ˚C IC = 3 A; IB = 0.6 A IC = 3 A; VCE = 5 V Ic=2.5A,IB1=0.5A PIN CONFIGURATION SYMBOL DESCRIPTION c case 1 base 2 collector 3 emitter ns b case isolated e 1 2 3 LIMITING VALUES Limiting values in accordance with the Absolute Maximum Rating System (IEC 134) SYMBOL PARAMETER CONDITIONS VCESM VCEO VCBO IC ICM IB IBM Ptot Tstg Tj Collector to emitter voltage Collector to emitter voltage (open base) Collector to base voltage (open emitter) Collector current (DC) Collector current peak value Base current (DC) Base current peak value Total power dissipation Storage temperature Junction temperature VBE = 0 V Ths ≤ 25 ˚C MIN. MAX. UNIT -65 - 1000 500 1000 5 10 2 4 32 150 150 V V V A A A A W ˚C ˚C TYP. MAX. UNIT - 3.95 K/W 55 - K/W THERMAL RESISTANCES SYMBOL PARAMETER CONDITIONS Rth j-hs Junction to heatsink with heatsink compound Rth j-a Junction to ambient in free air August 1998 1 Rev 1.000 Philips Semiconductors Preliminary specification Silicon Diffused Power Transistor BUJ303AX ISOLATION LIMITING VALUE & CHARACTERISTIC Ths = 25 ˚C unless otherwise specified SYMBOL PARAMETER CONDITIONS Visol R.M.S. isolation voltage from all three terminals to external heatsink f = 50-60 Hz; sinusoidal waveform; R.H. ≤ 65% ; clean and dustfree Cisol Capacitance from T2 to external f = 1 MHz heatsink MIN. TYP. - MAX. UNIT 2500 V - 10 - pF MIN. TYP. MAX. UNIT VBE = 0 V; VCE = VCESMmax VBE = 0 V; VCE = VCESMmax; Tj = 125 ˚C - - 1.0 2.0 mA mA VCBO = VCESMmax (1000V) VCEO = VCEOMmax (500V) - - 0.1 0.1 mA mA 500 - 0.1 - mA V VCEsat VBEsat hFE hFE VEB = 9 V; IC = 0 A IB = 0 A; IC = 100 mA; L = 25 mH Collector-emitter saturation voltages IC = 3 A; IB = 0.6 A Base-emitter saturation voltage IC = 3 A; IB = 0.6 A DC current gain IC = 5 mA; VCE = 5 V IC = 500 mA; VCE = 5 V 10 14 0.25 0.97 22 25 1.5 1.3 35 35 V V hFEsat DC current gain 10 - 13.5 12 17 - TYP. MAX. UNIT 0.5 3.3 0.33 0.7 4 0.45 µs µs µs 1.4 145 1.6 160 µs ns 1.7 160 1.9 200 µs ns STATIC CHARACTERISTICS Ths = 25 ˚C unless otherwise specified SYMBOL PARAMETER CONDITIONS 1 ICES ICES Collector cut-off current ICBO ICEO Collector cut-off current 1 IEBO VCEOsust Emitter cut-off current Collector-emitter sustaining voltage IC = 2.5 A; VCE = 5 V IC = 3 A; VCE = 5 V DYNAMIC CHARACTERISTICS Ths = 25 ˚C unless otherwise specified SYMBOL ton ts tf PARAMETER CONDITIONS Switching times (resistive load) ICon = 2.5 A; IBon = -IBoff = 0.5 A; RL = 75 ohms; VBB2 = 4 V; Turn-on time Turn-off storage time Turn-off fall time Switching times (inductive load) ts tf Turn-off storage time Turn-off fall time Switching times (inductive load) ts tf Turn-off storage time Turn-off fall time ICon = 2.5 A; IBon = 0.5 A; LB = 1 µH; -VBB = 5 V ICon = 2.5 A; IBon = 0.5 A; LB = 1 µH; -VBB = 5 V; Tj = 100 ˚C 1 Measured with half sine-wave voltage (curve tracer). August 1998 2 Rev 1.000 Philips Semiconductors Preliminary specification Silicon Diffused Power Transistor BUJ303AX ICon 90 % + 50v 100-200R 90 % IC 10 % ts Horizontal ton tf toff Oscilloscope IBon IB Vertical 10 % 300R 1R tr 30ns 6V 30-60 Hz -IBoff Fig.4. Switching times waveforms with resistive load. Fig.1. Test circuit for VCEOsust. VCC IC / mA LC 250 200 IBon LB 100 T.U.T. -VBB 0 min VCE / V VCEOsust Fig.2. Oscilloscope display for VCEOsust. Fig.5. Test circuit inductive load. VCC = 300 V; -VBE = 5 V; LC = 200 uH; LB = 1 uH VCC ICon 90 % IC RL VIM 10 % RB 0 T.U.T. ts toff tp IB tf t IBon T t -IBoff Fig.6. Switching times waveforms with inductive load. Fig.3. Test circuit resistive load. VIM = -6 to +8 V VCC = 250 V; tp = 20 µs; δ = tp / T = 0.01. RB and RL calculated from ICon and IBon requirements. August 1998 3 Rev 1.000 Philips Semiconductors Preliminary specification Silicon Diffused Power Transistor 120 110 BUJ303AX Normalised Derating % VBEsat/V with heatsink compound 1.4 100 1.2 90 80 70 1.0 0.8 60 P tot 50 40 0.6 30 0.4 20 10 0.2 0 0.0 0 20 40 60 80 Ths / C 100 120 140 0.1 1.0 IC/A 10.0 Fig.10. Base-Emitter saturation voltage. Solid lines = typ values, VBEsat = f(IC); at IC/IB =4. Fig.7. Normalised power dissipation. PD% = 100⋅PD/PD 25˚C = f (Ths) h FE 100 VCEsat/V 5V 0.5 0.4 10 0.3 0.2 Tj = 25 C 1V 0.1 1 0.01 0.1 1 10 0.0 IC / A 0 Fig.8. Typical DC current gain. hFE = f(IC) parameter VCE 2.0 1 IC/A 10 Fig.11. Collector-Emitter saturation voltage. Solid lines = typ values, VCEsat = f(IC); at IC/IB =4. VCEsat/V 10 Zth / (K/W) BU1706AX 1.6 IC=1A 2A 3A 0.5 4A 1 0.2 0.1 0.05 0.1 0.02 1.2 0.8 PD 0.4 0.10 IB/A 1.00 0.001 10.00 Fig.9. Collector-Emitter saturation voltage. Solid lines = typ values, VCEsat = f(IB); Tj=25˚C. August 1998 D= tp T 0.01 D=0 0.0 0.01 tp 1u t T 10u 100u 1m 10m 100m t/s 1 10 100 Fig.12. Transient thermal impedance. Zth j-hs = f(t); parameter D = tp/T 4 Rev 1.000 Philips Semiconductors Preliminary specification Silicon Diffused Power Transistor BUJ303AX IC/V 11 100 IC / A 10 9 8 7 = 0.01 ICM max 10 6 IC max 5 tp = 4 10 us II 3 2 100 us (1) 1 1 0 0 200 400 600 800 1,000 1,200 VCE CLAMP/V 1 ms Fig.13. Reverse bias safe operating area. Tj ≤ Tj max 10 ms I 0.1 (2) 500 ms DC VCC III 0.01 1 10 1000 100 VCE / V LC Fig.15. Forward bias safe operating area. Ths ≤ 25 ˚C IBon -VBB VCL (1) (2) I II III LB T.U.T. NB: Fig.14. Test circuit for reverse bias safe operating area. Vcl ≤ 1000V; Vcc = 150V; VBB = -5V; LB = 1µH; Lc = 200µH August 1998 5 Ptot max and Ptot peak max lines. Second breakdown limits. Region of permissible DC operation. Extension for repetitive pulse operation. Extension during turn-on in single transistor converters provided that RBE ≤ 100 Ω and tp ≤ 0.6 µs. Mounted with heatsink compound and 30 ± 5 newton force on the centre of the envelope. Rev 1.000 Philips Semiconductors Preliminary specification Silicon Diffused Power Transistor BUJ303AX MECHANICAL DATA Dimensions in mm Net Mass: 2 g 10.3 max 4.6 max 3.2 3.0 2.9 max 2.8 Recesses (2x) 2.5 0.8 max. depth 6.4 15.8 19 max. max. 15.8 max seating plane 3 max. not tinned 3 2.5 13.5 min. 1 0.4 2 3 M 1.0 (2x) 0.6 2.54 0.9 0.7 0.5 2.5 5.08 1.3 Fig.16. SOT186A; The seating plane is electrically isolated from all terminals. Notes 1. Refer to mounting instructions for F-pack envelopes. 2. Epoxy meets UL94 V0 at 1/8". August 1998 6 Rev 1.000 Philips Semiconductors Preliminary specification Silicon Diffused Power Transistor BUJ303AX DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications. Limiting values Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of this specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. Philips Electronics N.V. 1998 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, it is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. August 1998 7 Rev 1.000