SONY CXA2153

CXA2153S
Preamplifier for High Resolution Computer Display
Description
The CXA2153S is a bipolar IC developed for high
resolution computer displays.
Features
• Built-in wide-band amplifier: 180MHz@–3dB (Typ.)
• Input dynamic range: 1.0Vp-p (Typ.)
• High gain preamplifier (15dB)
• R, G and B incorporated in a single package
(SDIP 30 pins)
• I2C bus control
Contrast control
R/G/B drive control
Brightness control
OSD contrast control
4-channel DAC control output
• Built-in gamma function
• Built-in high-speed ABL blanking
• Built-in sync separator for Sync on Green
• Built-in blanking mixing function
(with blanking level fixed at 0.4V)
• Built-in OSD mixing function
• Video period detection function
• Built-in VBLK synchronous DAC refresh system
Applications
High resolution computer displays
30 pin SDIP (Plastic)
Absolute Maximum Ratings (Ta = 25°C, GND = 0V)
• Supply voltage
Vcc12
13
V
Vcc5
5.5
V
• Operating temperature Topr
–20 to +75
°C
• Storage temperature Tstg
–65 to +150
°C
• Allowable power dissipation
2.05
W
PD
• Pin voltage
Vcc5 + 0.3V
1, 3, 4, 6, 7, 8, 9, 10, 11,
12, 13, 14, 15, 16, 17 (Pin)
VREF (Pin 23) + 0.3V
18, 19, 20, 21, 25, 27,
29 (Pin)
Recommended Operating Conditions
Supply voltage
Vcc12
12 ± 0.5
Vcc5
5 ± 0.25
V
V
Structure
Bipolar silicon monolithic IC
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by
any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the
operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
–1–
E99X02A1Y-PS
16 17
7
1
ABL
RIN
–2–
3
6
BIN
Bch
Clamp Gch
Sharpness
Buffer
Clamp
BRIGHTNESS
SYNC OFF
SYNC SEP.
Clamp
SYNCOUT
ROUT
BLK
GOUT
BOUT
12
29
14
27
25
VDET LEVEL/VDET OFF
Bch (Same as Rch)
BLK
AMP
Blanking Mix
Rch
Gch (Same as Rch)
OSD/OSD_BLK
Mix
Video
Detector
SHP GAIN/
SHP WIDTH
Gain Control
AMP
G2 18
Gamma
B_BKG 19
Rch
GAMMA1/GAMMA2/GM OFF
POL1/POL2
G_BKG 20
OSD GAIN
R_BKG 21
GIN
ABL
Contrast
Regulator
VCC12 22
DRIVE
D/A
Converter
VREF 23
LPF
Latch
4
SCL
I2C Bus
Decoder
SYNCIN
SDA
CXA2153S
Block Diagram
8
OSD_BLK
9
OSD_R
10
OSD_G
11
OSD_B
15
VDET
13
CLP
CXA2153S
Pin Configuration
RIN
1
30 VCC12
VCC5
2
29 ROUT
GIN
3
28 GND_R
SYNCIN
4
27 GOUT
GND
5
26 GND_G
BIN
6
25 BOUT
ABL
7
24 GND_B
OSD_BLK
8
23 VREF
OSD_R
9
22 VCC12
OSD_G 10
21 R_BKG
OSD_B 11
20 G_BKG
SYNCOUT 12
19 B_BKG
CLP 13
18 G2
BLK 14
17 SCL
VDET 15
16 SDA
–3–
CXA2153S
Pin Description
Pin
No.
Symbol
Pin voltage
Equivalent circuit
Description
VCC
1k
VCC
VCC
1
3
6
RIN
GIN
BIN
3.1V
(CLAMP)
RGB signal inputs.
Input via the capacitor.
1
3
1k
6
1k
2
Vcc5
5V
5V power supply.
VCC
VCC
VCC 100
4
SYNCIN
Sync-on-green signal input.
Input via the capacitor.
2.9V
4
150
5
GND
GND
VCC
VCC
500
5V
VCC
2k
500
VCC
7
ABL
2.5V
(when
open)
10k
ABL input.
7
20k
10k
VCC
VCC
8
5k
OSD_BLK
8
30k
–4–
5k
OSD_BLK control input.
VILMAX = 0.8V
VIHMIN = 2.8V
CXA2153S
Pin
No.
Symbol
Pin voltage
Equivalent circuit
Description
VCC
VCC
VCC
9
10
11
OSD_R
OSD_G
OSD_B
5k
OSD control input.
VILMAX = 0.8V
VIHMIN = 2.8V
5k
9
10
30k
11
VCC
VCC
VCC
100
VCC
5k
20k
12
SYNCOUT
12
200
200
Sync separator output of Syncon-green signal.
I2C bus SOG off: Output at 0.
Typ.: High = 4.2V
Low = 0.2V
(positive polarity)
VCC
VCC
13
Clamp pulse (positive polarity)
input.
VILMAX = 0.8V
VIHMIN = 2.8V
CLP
13
30k
VCC
VCC
VCC
5k
14
BLK
14
30k
–5–
5k
Blanking pulse input.
Set the V blanking pulse width
to 300µs or more.
VILMAX = 1.2V
VIHMIN = 4.7V
CXA2153S
Pin
No.
Symbol
Pin voltage
Equivalent circuit
Description
VREF VCC
VCC
10k
100
VCC
20k
15
Video detector output.
I2C bus VDET off: Output at 0.
VDET
15
200
200
VCC
16
I2C bus standard SDA (serial
data) input/output.
VILMAX = 1.5V
VIHMIN = 3.5V
VOLMAX = 0.4V
4k
SDA
16
VCC
17
I2C bus standard SCL (serial
clock) input.
VILMAX = 1.5V
VIHMIN = 3.5V
4k
SCL
17
10k
VREG
VCC
21
20
19
18
R_BKG
G_BKG
B_BKG
G2
100
VREG
1k
BKG/G2 adjustment DAC
outputs.
The output DC is 1.5 to 5.5V.
21
20
19
18
100
22
30
Vcc12
12V
1k
12V power supply
–6–
CXA2153S
Pin
No.
Symbol
Pin voltage
Equivalent circuit
VCC12
23
VREF
VCC12
9V
23
Band Gap
28
26
24
GND_R
GND_G
GND_B
Description
0V
9V regulator.
Connect with Vcc12 via a
resistor of around 220Ω.
It cannot be used as an
external power supply.
GNDs
VCC12 VREG
29
27
25
ROUT
GOUT
BOUT
VCC
R, G and B signal outputs.
29
27
25
–7–
CXA2153S
I2C BUS Register Definitions
Slave Address
SLAVE RECEIVER: 40 (HEX)
Register Table
Sub Address
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
00h
CONTRAST
01h
BRIGHTNESS
02h
R_BKG
03h
G_BKG
04h
B_BKG
05h
OSD GAIN
06h
G2
07h
R_DRV
08h
G_DRV
09h
B_DRV
0Ah
∗
0Bh
POL1
0Ch
∗
∗
SHP WIDTH
GAMMA1
∗
POL2
BIT 2
BIT 1
BIT 0
SHP GAIN
GAMMA2
VDET LVL VDET OFF SOG OFF GAM OFF
0
D R OFF
∗: Don't Care
Sub Address 0000 CONTRAST (8)
Controls the gain common to the R, G and B channels. Since control is
performed by multiplying with R/G/B DRIVE, the white balance can be
adjusted by R/G/B DRIVE and the luminance can be adjusted by
CONTRAST.
0: Output level minimum (0Vp-p)
255: Output level maximum (4.4Vp-p; with 0.7Vp-p input)
Sub Address 0001 BRIGHTNESS (8) Controls the black level common to the R, G and B channels.
0: Black level minimum (0.8V)
255: Black level maximum (2.9V)
Sub Address 0010 R_BKG (8)
Controls Pin 21 (R BACKGROUND) output voltage.
0: Output voltage minimum (1.5V)
255: Output voltage maximum (5.5V)
Sub Address 0011 G_BKG (8)
Controls Pin 20 (G BACKGROUND) output voltage.
0: Output voltage minimum (1.5V)
255: Output voltage maximum (5.5V)
Sub Address 0100 B_BKG (8)
Controls Pin 19 (B BACKGROUND) output voltage.
0: Output voltage minimum (1.5V)
255: Output voltage maximum (5.5V)
–8–
CXA2153S
Sub Address 0101 OSD GAIN (8)
Controls the OSD gain common to the R, G and B channels. Since
control is performed by multiplying with R/G/B DRIVE, the video white
balance and tracking are obtained.
0: Gain minimum (0Vp-p)
255: Gain maximum (4.5Vp-p)
Sub Address 0110 G2 (8)
Controls Pin 18 (G2) output voltage.
0: Output voltage minimum (1.5V)
255: Output voltage maximum (5.5V)
Sub Address 0111 R_DRV (8)
Controls the gain for the R channel. Control is performed by multiplying
with CONTRAST. Use this for adjusting the white balance.
0: Output level minimum (0Vp-p)
255: Output level maximum (4.4Vp-p; with 0.7Vp-p input)
Sub Address 1000 G_DRV (8)
Controls the gain for the G channel. Control is performed by multiplying
with CONTRAST. Use this for adjusting the white balance.
0: Output level minimum (0Vp-p)
255: Output level maximum (4.4Vp-p; with 0.7Vp-p input)
Sub Address 1001 B_DRV (8)
Controls the gain for the B channel. Control is performed by multiplying
with CONTRAST. Use this for adjusting the white balance.
0: Output level minimum (0Vp-p)
255: Output level maximum (4.4Vp-p; with 0.7Vp-p input)
Sub Address 1010 SHP WIDTH (2)
Controls the sharpness time constant switching.
0: OFF
1: 25ns
2: 50ns
3: 100ns
Sub Address 1010 SHP GAIN (4)
Controls the sharpness gain.
0: Gain minimum (0dB)
F: Gain maximum (6dB) ∗ Amplitude at SHP OFF is assumed to be 0dB.
Sub Address 1011 POL1 (1)
Controls the polarity of the correction at GAMMA1.
0: – correction
1: + correction
Sub Address 1011 GAMMA1 (2)
Controls the gain of the inflection point 1 (15 IRE) at GAMMA.
0: 0 IRE correction
3: 9 IRE correction
Sub Address 1011 POL2 (1)
Controls the polarity of the correction at GAMMA2.
0: – correction
1: + correction
–9–
CXA2153S
Sub Address 1011 GAMMA2 (4)
Controls the gain of the inflection point 2 (60 IRE) at GAMMA.
0: 0 IRE correction
7: 20 IRE correction
Sub Address 1100 VDET LVL (1)
Controls the signal detection (VDET) slice level.
0: Slice level (160mV when RIN or GIN or BIN)
1: Slice level (200mV when RIN or GIN or BIN)
Sub Address 1100 VDET OFF (1)
Controls the video detection output.
0: Output on
1: Output off
Sub Address 1100 SOG OFF (1)
Controls the sync separator output.
0: Output on
1: Output off
Sub Address 1100 GM OFF (1)
Controls the gamma function operation.
0: Gamma on
1: Gamma off
Sub Address 1100 D R OFF (1)
Controls the VBLK synchronous DAC refresh function. The operation of
this function is set to OFF when the power is turned on.
0: Function operation on
1: Function operation off
– 10 –
CXA2153S
I2C BUS Logic System
No.
Item
Symbol
Min.
Typ.
Max.
Unit
1
High level input voltage
VIH
3.0
—
5.0
V
2
Low level input voltage
VIL
0
—
1.5
V
3
Low level output voltage
SDA during current inflow of 3mA
VOL
0
—
0.4
V
4
Maximum clock frequency
fSCL
0
—
400
kHz
5
Minimum waiting time for data change
1.3
—
—
µs
6
Minimum waiting time for data transfer start
0.6
—
—
µs
7
Low level clock pulse width
1.3
—
—
µs
8
High level clock pulse width
0.6
—
—
µs
9
Minimum waiting time for start preparation
0.6
—
—
µs
10
Minimum data hold time
0
—
900
ns
11
Maximum data preparation time
100
—
—
ns
12
Rise time
—
—
1
µs
13
Fall time
—
—
300
ns
14
Minimum waiting time for stop preparation
tBUF
tHD; STA
tLOW
tHIGH
tSU; STA
tHD; DAT
tSU; DAT
tR
tF
tSU; STO
0.6
—
—
µs
– 11 –
CXA2153S
Electrical Characteristics
No. Measurement item
Symbol
Measurement contents
Min. Typ. Max. Unit
Vcc5 (5V) pin inflow current
RGB signal input: None
38
55
73
mA
Current consumption
Icc2
(12V)
Vcc12 (12V) pin inflow current
RGB signal input: None
28
42
57
mA
Current consumption
Icc3
(12V OFF)
Pin inflow current when 12V OFF
RGB signal input: None
3.4
4.9
6.6
mA
Measure input rise time (TR1), input fall time
(TF1), input rise time (TR2) and input fall
time (TF2), then substitute these values into
the following equations.
0.9
1.96
3
1
Current
consumption (5V)
2
3
Icc1
TR
TR = √(TR22 – TR12), TF = √(TF22 – TF12)
(Contrast = 7F, DRIVE = FF, BRIGHTNESS = 7F)
4
Pulse characteristics
TR∗
ns
TF∗
VIDEO amplitude 90%
1.6
3.1
4.6
4
4.4
4.8
–100
0
120 mVp-p
Calculate the difference in the data obtained
–180
in No.5 and No.6 between the channels.
0
180
TF
VIDEO amplitude 0%
5
Contrast control 1
GCONT1
Measure the level of the output signal
amplitude Vout when a 0.7Vp-p video signal
is input.
GCONT1: Contrast = DRIVE = FF
GCONT2: Contrast = 00/DRIVE = FF
Vp-p
Input signal
0.7Vp-p
6
Contrast control 2
GCONT2
7
Relative contrast
GCONGAP
– 12 –
mV
CXA2153S
No. Measurement item
Symbol
Measurement contents
Min. Typ. Max. Unit
Measure the level of the output signal
amplitude Vout when a 0.7Vp-p video
signal is input.
Contrast = FF/DRIVE = 00
8
Drive control
GDRV
–100
Input signal
0
120 mVp-p
0.7Vp-p
GOSD1
9
Measure the OSD level of the output signal
when the OSD pulse is input.
GOSD1: OSD = FF/DRIVE = FF
GOSD2: OSD = 00/DRIVE = FF
4
4.57 5.15 Vp-p
OSD period
OSD gain control
RGB output signal
OSD
level
–330
0
360 mVp-p
Calculate the difference in the data obtained
–200
in No.9 between the channels.
0
200
0.8
0.95
GOSD2
10 Relative OSD
OSDGAP
VBRT1
11 Brightness control
Measure the black level of the RGB output
signal.
VBRT1: Brightness = 00
VBRT2: Brightness = FF
0.6
V
RGB output signal
Black level
VBRT2
mV
2.5
2.93 3.28
GND
12 Relative brightness
VBRTGAP
Calculate the difference in the data obtained
–200
in No.11 between the channels.
0
200
mV
Measure the BLK level of the output signal
when a BLK pulse is input.
13 BLK level
0.13 0.43 0.74
VBLK
BLK level
GND
– 13 –
V
CXA2153S
No. Measurement item
Sync separator
output rise delay
Symbol
Measurement contents
Sync-IN
SDLYR
Min. Typ. Max. Unit
6.5
8.5
11
Vth = 50%
14
Fall
Delay
Rise Delay
ns
Vth = 50%
Sync separator
output fall delay
SDLYF
Sync-OUT
6.5
8.8
11
3.9
4
—
Sync separator output
Sync-Hi
15 Sync separator
output
V
Sync-Lo
Sync-Lo
Sync-Hi
—
0.2
0.45
—
—
7.2
10
GND
Sync separator
16
capacity
VDET output rise
delay
SyncChk
Gradually reduce the sync level when the
duty is cycle 4.8% and 22.7% from 0.3Vp-p
0.24
and measure the sync level at which the
sync signals can be separated.
RGB input
DDLYR
5.5
0.7Vp-p
Vth = 50%
17
Rise
Delay
VDET output fall
delay
Vp-p
Vth = 50%
DDLYF
ns
Fall
Delay
8.5
11.9 15.5
VDET output
VDET-Hi
VDET output
4
4.1
—
18 VDET output
V
VDET-Lo
VDET-Lo
VDET-Hi
GND
– 14 –
—
0.25
0.4
CXA2153S
No. Measurement item
DAC output voltage
(BKG = 00)
Symbol
VBKG1
Measurement contents
Measure the DAC output voltage (Pin 20)
when BKG = 00/FF.
Min. Typ. Max. Unit
1.25 1.45 1.67
19
V
DAC output voltage
(BKG = FF)
VBKG2
5.45
5.7
5.95
3.35
3.8
4.4
0.3
0.4
0.5
0.3
0.4
0.5
0.6
0.8
1.0
0.5
0.65
0.8
Input the crosshatch signal of Dot Clock
100MHz/ 0.7p-p to the RGB inputs, and
measure the VDET output amplitude.
VDET LEVEL = 0
20
VDET output
amplitude
VDET
Input signal
Vp-p
0.7Vp-p
10ns
Sharpness gain 1
SHP1
21 Sharpness gain 2
SHP2
Input a 10MHz sin wave to RGB at an
amplitude of 0.1Vp-p, and measure the
output level.
(CONTRAST: 7F/DRIVE: FF/ABL: 5V)
SHP1: SHP GAIN = F/SHP SW = 0
SHP2: SHP GAIN = 0/SHP SW = 3
SHP3: SHP GAIN = F/SHP SW = 3
Input signal
Sharpness gain 3
GAM2
22 Gamma correction
GAM3
GAM4
Vp-p
0.1Vp-p
CLP potential
(approximately 3.1V)
SHP3
GAM1
10ns
Input 15 [IRE] and 60 [IRE] amplitude
signals (100 [IRE] = 0.7Vp-p) to the RGB
inputs, and measure the output amplitude.
GAM1: GAMMA1 = 3/POL1 = 1,
Vin = 0.105Vp-p
GAM2: GAMMA1 = 3/POL1 = 0,
Vin = 0.105Vp-p
GAM3: GAMMA2 = F/POL2 = 1,
Vin = 0.42Vp-p
GAM4: GAMMA2 = F/POL2 = 0,
Vin = 0.42Vp-p
(CONTRAST: 7F/DRIVE: FF/ABL: 5V)
– 15 –
0.05 0.15 0.25
Vp-p
1.8
2.1
2.4
0.8
1.0
1.25
CXA2153S
Control Characteristics
OSD GAIN Control Characteristics
5.0
4.5
4.5
4.0
4.0
3.5
3.5
Output level [Vp-p]
Output level [Vp-p]
CONTRAST Control Characteristics
5.0
3.0
2.5
2.0
1.5
3.0
2.5
2.0
1.5
1.0
1.0
0.5
0.5
0
0
32
64
96
0
128 160 192 224 256
0
32
64
CONTRAST data
96
128 160 192 224 256
OSD GAIN data
DRIVE Control Characteristics
BRIGHTNESS Control Characteristics
3.0
5.0
4.5
2.5
3.5
Output voltage [V]
Output level [Vp-p]
4.0
3.0
2.5
2.0
1.5
2.0
1.5
1.0
1.0
0.5
0
0
32
64
0.5
96 128 160 192 224 256
DRIVE data
0
90
5.5
80
5.0
70
4.5
60
50
40
30
3.5
3.0
2.5
2.0
10
1.5
2
3
ABL pin voltage [V]
4
128 160 192 224 256
4.0
20
1
96
RGB BKG/G2 Control Characteristics
6.0
Output voltage [V]
RGB output amplitude [%]
ABL Control Characteristics
0
64
BRIGHTNESS data
100
0
32
1.0
5
– 16 –
0
32
64
96
128 160 192 224 256
Control data
CXA2153S
Frequency Characteristic
14
12
10
Output gain [dB]
8
6
4
2
0
–2
–4
1
10
100
Input frequency [MHz]
– 17 –
1000
CXA2153S
Electrical Characteristics Measurement Circuit
47µF
0.1µF
12V
1
RIN
VCC12 30
2
VCC5
ROUT 29
3
GIN
4
SYNCIN
5
GND
6
BIN
BOUT 25
7
ABL
GND_B 24
8
OSD_BLK
47µF
75
0.1µF
Rch Output
5V
0.1µF
GND_R 28
0.1µF
75
Gch Output
GOUT 27
0.1µF
75
GND_G 26
Bch Output
0.1µF
75
0.1µF
10µF
VREF 23
220
OSD_R
VCC12 22
10 OSD_G
R_BKG 21
11 OSD_B
G_BKG 20
9
47µF
12V
0.1µF
DAC
Output
SYNC SEP Output
B_BKG 19
12 SYNCOUT
13 CLP
G2 18
14 BLK
SCL 17
220
VDET Output
SDA 16
15 VDET
220
– 18 –
I2C Bus
CXA2153S
Electrical Characteristics Measurement Circuit (Frequency Response)
1k
47µF
0.1µF
12V
1
RIN
VCC12 30
2
VCC5
ROUT 29
3
GIN
4
SYNCIN
5
GND
6
BIN
BOUT 25
7
ABL
GND_B 24
8
OSD_BLK
47µF
75
5V
1k
0.1µF
Rch Output
0.1µF
GND_R 28
0.1µF
75
Gch Output
GOUT 27
0.1µF
1k
GND_G 26
Bch Output
0.1µF
75
5V
0.1µF
10µF
VREF 23
220
OSD_R
VCC12 22
10 OSD_G
R_BKG 21
11 OSD_B
G_BKG 20
9
VREF
47µF
12V
0.1µF
DAC
Output
SYNC SEP Output
B_BKG 19
12 SYNCOUT
13 CLP
G2 18
14 BLK
SCL 17
220
VDET Output
SDA 16
15 VDET
220
– 19 –
I2C Bus
CXA2153S
Application Circuit
47µF
0.1µF
Rch Input
12V
1
RIN
VCC12 30
2
VCC5
ROUT 29
3
GIN
4
SYNCIN
5
GND
6
BIN
BOUT 25
7
ABL
GND_B 24
8
OSD_BLK
47µF
75
0.1µF
Rch Output
0.1µF
Gch Input
GND_R 28
0.1µF
Gch Output
75
GOUT 27
0.1µF
GND_G 26
Bch Input
Bch Output
0.1µF
75
0.1µF
10µF
VREF 23
220
OSD_R
VCC12 22
10 OSD_G
R_BKG 21
11 OSD_B
G_BKG 20
9
47µF
12V
0.1µF
DAC
Output
SYNC SEP Output
B_BKG 19
12 SYNCOUT
13 CLP
G2 18
14 BLK
SCL 17
220
VDET Output
I2C Bus
SDA 16
15 VDET
220
Application circuits shown are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for
any problems arising out of the use of these circuits or for any infringement of third party patent and other right due to same.
– 20 –
CXA2153S
Description of Operation
1. Sharpness function
The RGB signals input to Pins 5, 7 and 10 are mixed at a ratio of 0.6G + 0.3R + 0.1B to form the Y signal. The
high-frequency component is removed from this Y signal by a differentiation circuit, and the amplitude is
controlled by a gain control circuit. The signal which undergoes gain control (sharpness component) has its
amplitude clipped by a limiter circuit and is then added to the R, G and B signals.
SHP GAIN = 0 (HEX)
or SHP OFF = 1
No sharpness component
Section not sent to RGB output because of the limiter
100%
Limiter level = 30% (Typ.)
SHP GAIN = F (HEX)
100%
10%
25ns
(T SW = 1)
∗ The output level when RIN = GIN = BIN = 0.7Vp-p
is set to 100%.
50ns
(T SW = 2)
100ns
(T SW = 3)
2. VBLK synchronous DAC refresh system
The VBLK signal is removed from the composite BLK signal which has been input to Pin 14, and the data for
each control DAC is overwritten all at once in synchronization with this VBLK signal. The received I2C bus data
is held by a latch until the next VBLK signal arrives. As a result, I2C bus data transmission from the
microcomputer is timing-free. Set the width of the V blanking pulse which is input to Pin 14 to 300µs or more.
(See the next page)
3. Gamma correction function
Using the output obtained when 700mVp-p RGB signals are input as a reference (100 [IRE]), the ±9 [IRE]
(GAMMA1) and ±20 [IRE] (GAMMA2) waveforms can be corrected at the 15 [IRE] and 60 [IRE] inflection points,
respectively.
The polarity switching gain can be controlled separately for each point, enabling correction broken at two
points. The I2C bus controls the polarity switching and gain correction.
GAMMA1
GAMMA2
+20 [IRE]
–20 [IRE]
100 [IRE]
100 [IRE]
+9 [IRE]
–9 [IRE]
0
15 [IRE]
100 [IRE]
0
– 21 –
60 [IRE]
100 [IRE]
CXA2153S
VBLK Synchronous DAC Refresh System
VBLK
Transmission period
Bus data transmission
Data group (2)
Data group (1)
Data group (3)
enable
DAC refresh
enable signal
disable
DAC refresh
signal
The latest data which was sent
before VBLK is written to the DAC.
In this case the data in (1) is written.
The DAC is not rewritten while the
bus data in the VBLK period is being
transmitted. The transmitted data is held.
The data in (3) written.
The data in (2) written,
if (3) is not transmitted.
The VBLK signal is extracted from the composite BLK signal which has been input to Pin 14, and the DAC data
for each control is rewritten all at once in synchronization with this VBLK signal. The received I2C bus data is held
by a latch until the next VBLK signal arrives. Therefore, I2C bus data transmission from the microcomputer is
timing-free. Set the width of the V blanking pulse which is input to Pin 14 to 300µs or more.
Operation during power saving (Pin 22, VCC12 OFF)
Only the sync separator function operates. All the other functions are shut down.
– 22 –
CXA2153S
Notes on Operation
1.
2.
3.
Set the output for ROUT, GOUT and BOUT for reception at high impedance.
Make the wiring from ROUT, GOUT and BOUT to the power amplifier as short as possible.
Connect the Vcc5, Vcc12 and VREF decoupling capacitors so that the ceramic capacitor and electrolytic
capacitor are connected in parallel and the distance from the IC is less than 3mm.
4. Connect the clamp capacitors for RIN, GIN and BIN so that the distance from the IC is as short as
possible.
5. Input the signals to RIN, GIN and BIN at low impedance via a clamp capacitor.
6. Set the output to OFF when the VDET/CSYNC output is not used. (Otherwise, this may cause the
crosstalk to deteriorate.)
7. The VREF output cannot be used as an external power supply.
8. Turn the power on in the order of 5V → 12V, and off in the order of 12V → 5V. (Be sure to observe this
order particularly during power-off, otherwise spots may remain on the screen.)
9. When applying blanking to the video period, the blanking pulse input to the BLK pin should have a high
level of 4.7V or more.
10. When not using the sync separation function, connect the Sync In pin to GND through a capacitor, and set
SOG_OFF = 1 (bus setting).
11. When there is no clamp pulse input to Pin 13 (CLP), the output potential rises. Always input a clamp
pulse.
– 23 –
CXA2153S
Package Outline
Unit: mm
+ 0.1
.05
0.25 – 0
30PIN SDIP (PLASTIC)
+ 0.4
26.9 – 0.1
30
+ 0.3
8.5 – 0.1
10.16
16
0° to 15°
15
1
+ 0.4
3.7 – 0.1
0.5 MIN
1.778
0.5 ± 0.1
3.0 MIN
Two kinds of package surface:
1.All mat surface type.
2.All mirror surface type.
0.9 ± 0.15
PACKAGE STRUCTURE
MOLDING COMPOUND
EPOXY RESIN
PALLADIUM PLATING
SONY CODE
SDIP-30P-01
LEAD TREATMENT
EIAJ CODE
P-SDIP30-8.5x26.9-1.778
LEAD MATERIAL
COPPER ALLOY
PACKAGE MASS
1.8g
JEDEC CODE
– 24 –
Sony Corporation